Fedora Installation :: 11 Installer Doesn't Detect Seagate Sata Disk
Jul 8, 2009
I have an Asus P5K motherboard with an Intel Core 2 Duo 8400. It has 2 SATA hard disks, a 250 GB Seagate and a 500GB Hitachi.
I've been running Fedora 10 x86_64 for 6 months on this computer without problems.
I'm trying to do a new Fedora 11 install on this computer but the installer (Anaconda?) only detects the Hitachi disk.
I've tried to make a new Fedora 10 install to check if it was a media or disk problem and it detects the two hard disks.
I've tried to install it via a Live CD, and the installer only detects the Hitachi disk. The LiveCD detects the two hard disks, I can access it, partition, format, write, but the installer only detects the Hitachi.
I've tried to change from Enhanced SATA (AHCI) to Compatible in BIOS without success and I've changed SATA cables from one disk to the other, changed the disk order and nothing.
Must I enter some boot parameters for Fedora 11? Has the LiveCD installer some options?
View 2 Replies
ADVERTISEMENT
Jul 12, 2010
I have a dual CPU Xeon machine that I have been using various versions of fedora on for years.
The machine has the following disk layout:
I currently have Fedora 10 and grub installed on hda and I had to jump through hoops to install such as disabling the promise controller and reassigning drives because that blasted /dev/mapper kept grabbing the Maxtor ATA drives although I didn't want it to.
Anyway, in the BIOS I can boot from the secondary IDE controller so I want to install Fedora 13 on hdb. Problem is, the Fedora installer won't detect the drive.
Its partition table is as follows:
There is approximately 69GB of free space on this disk but the blasted python based installer wont show the disk as a possible installation location. If I exit to a bash shell I see that the device nodes do exist and I can manually mount and manipulate the disk but the installer is brain dead where the disk is concerned.
I will mention that sdc, sdi, and sdj are used with mdadm to create high performance striped volumes. Also, sdc shows up under /dev/mapper and I don't want to use /dev/mapper at all. I want simple /dev/sd? mount points...no stinking /dev/mapper, and no stinkin volume manager wrappers...
Why I cannot get the installer to use /dev/sdb?
Is there a disk signature on /dev/hd[bc] that is causing them to be grabbed by /dev/mapper, and if so, how would I remove that signature from the drive? /dev/mapper is vacant under Fedora 10.
View 2 Replies
View Related
Oct 12, 2010
I have a ssd cosair harddisk with both usb and sata connecters. If I connect it with sata anything is working fine, and I managed to install Fedora core 13.
But I also want to be able to use the harddisk when it is connected with usb and that causes problems.
When I boot the Fedora Core 13 dvd It can't detect my usb harddisk.
When booting in install mode it just don't detect the harddisk.
When booting the dvd in rescue mode it don't detect the harddisk, and it don't create any entries in /dev/ for the harddisk. It is like there is no disk at all.
I have tested this on 3 different computers, so it is not a problem with my specific motherboard. So either it is a problem between my harddisk and Fedora Core 13, or there is some problems with the usb drivers in the boot image used by the Fedora core 13 dvd.
The disk is working fine if I connect it via usb to an existing Windows install, so the usb connection is working.
I installed Fedora core 13 with the harddisk connected to sata and then re-connected the harddisk to usb. It then boot up, but complain about missing root filesystem. Most likely caused by missing usb driver in my kernel.
But anyway, what I really want is the ability to boot from both sata and usb, so I can take the harddisk with me and boot it on other computers with usb.
So is there a command which allows me to build an kernel image which can boot from usb or am I trying to do something which is not really supported?
I did update my fstab to use LABEL=myroot
There is 1 Windows partition(NTFS) and 1 linux partition on the disk. (No seperate /boot partition and no swap)
View 1 Replies
View Related
Oct 13, 2010
I've just installed Fedora (F13) for the first time, on a new HDD, to give myself a dual-boot system. So currently I have:
So, at the appropriate stage in the install menu, there is an option for where to install GRUB, and a drop-down to choose which drive is the primary BIOS boot drive.
However, in both cases, no other drive except my new sdc is visible. So, I can install GRUB to MBR of sdc, or to first sector of boot partition - but no option to put it to my primary boot drive MBR on sda.
Likewise, in the GRUB configuration page, if I go to Add another OS, the only option it gives me is my new Fedora install. It doesn't list the Vista OS on sda at all.
The result is that I can boot to either OS by changing the boot drive priority in BIOS.
I guess my question is this:
- is this expected behaviour from the installer, meaning that I'll need to configure GRUB manually somehow? (gulp ) or
- did I do something wrong in the install process? or
- is this some weird bug manifesting itself?
View 12 Replies
View Related
Oct 5, 2010
I have a Dell Poweredge 2970 2x3.0 GHz AMD 64bit dual core, Perc 5/i controller, and 2 brand new Fujitso SAS 15K 146GB drives.
Trying to install Ubuntu 10.04 Server 64 bit from USB. At the point of detecting disks, the installer only recognizes the USB. The installation was created using Pendriveinstaller ver1.8.0.1 per Ubuntu Server web site instructions. I have the drives configured as 2 separate raid 0 arrays using the bios raid configurator. The drives have been initialized. (Tried before with a single Raid 1 array, but had same issue and since have read Ubuntu support for hardware raid is not great, so was going to bypass hardware raid for now).
I've seen some chatter on here about opening a terminal at this point and removing dmraid but don't see an option for terminal only shell.
View 1 Replies
View Related
Apr 17, 2011
I downloaded this "debian-6.0.1a-amd64-netinst" iso image....But on the partitioning screen, after selecting the manual partitioning, it shows the whole hard disk without detecting the XP partitions.
View 2 Replies
View Related
Dec 19, 2009
Trying to install SUSE on a perfectly working PC that was running Windows. Blew away all the partitions and formated the drives.When trying to install SUSE, Installer will not detect my two hard disks. Tried with version 10.x, 11.1 and 11.2, without success.My Mobo is a XFX GeForce 8209, and my SATA drives are both Seagates (1x120GB, 1x320GB). I've tried different SATA mode selection (i.e. SATA, AHCI, and RAID) without any success either.I've tried to look for SATA controller drivers for my Mobo, to try to load on Installer startup, but failed there too.
View 1 Replies
View Related
Dec 19, 2010
I am trying to install Debian Lenny (64 bit) on my brand new Toshiba laptop (intel i3, 3 GB RAM) and for some reason the installer cannot detect the ethernet card. This is the error message I get:"No Ethernet card was detected. If you know the name of the driver needed by your Ethernet card, you can select it from the list."And then there's a list which is quite long -- and I cannot replicate it here. But I want to know why the installer cannot find the ethernet card on its own or find the appropriate driver. In any case how can I fix this problem?
View 14 Replies
View Related
Apr 20, 2011
Having trouble installing 'Squeeze' 6.0.1a-amd64-netinst on a new AMD64 system.The installer boots and runs fine until it gets to hard disk detection. Then it hangs for about 20 minutes showing a blue screen, during which time the HDD-activity light flickers every 5 seconds. Eventually it says it can't detect a hard disk, and displays a (longish) list of possible drivers; no idea which, if any, would suit.Anyone else installed (successfully or otherwise) on this combo?
View 3 Replies
View Related
Feb 16, 2011
I have a Windows XP system, and wanted to install Ubuntu to a 100 GB XT3 partition on the same drive. I was told I could chainload Ubuntu from the NT Loader menu. I booted from a Ubuntu 10.04 CD and ran the installer. It didn't find any hard drives. On a hunch, I tried the 10.04 alternate installer CD. That DID find the hard drive and partitions. I had the installer make /dev/sda7 (the XT3 partition) the root. Installation proceeded smoothly, but then the installer told me it did not see any other OS's on my drive! Why? I directed the installer to place grub on /dev/sda7 instead of the MBR.
Per the instructions I was given, I used DD to copy the first 512 bytes of /dev/sda7 to the Windows primary partition (sda1) as bootloader.lnx. But the resulting file is empty, and it won't boot. I repeated the whole process - formatting, installing FOUR times, and same results. I have no idea where GRUB was installed. It is apparently not in the MBR, because I still have my normal Windows boot. I downloaded the 10.10 alternate installer and got the same exact results. Even switched from XT3 to XT4. After two weeks of this nonsense, I still have yet to see Linux boot.
View 9 Replies
View Related
Feb 24, 2011
I have trouble installing ubuntu on my desktop machine. I had Mint before, reinstalled Win7 and wanted to upgrade to newest release as I didn't use Linux for some time.
Basically fdisk can see the disk but installer don't
View 5 Replies
View Related
Jun 11, 2009
I've been struggling a bit with install F11. F10 installs without issue. I have two internal SATA drives, a PATA DVD-ROM and a USB drive. The BIOS recognizes everything. However, when I got to the disk partition utility, Anaconda could never detect one of the SATA devices. I tried swapping cables, ports, etc. No luck. Today, I ran across this Bug thread: [URL] I checked the screens Ctrl-Alt-F1-6. Nothing obvious. But, for fun (from the bug thread) I went to the prompt on 2 and ran:
dmraid -r -E It found an "nvidia" RAID "thingy". Forgive my ignorance on what it really is called or what it does. Anyway, I answered yes to erase the "thingy" and voila. I was able to install F11. Not sure if I made a good title, but I've seen bits and pieces of people having similar problems with F11. And BTW, the drive that had "nvidia" on it was from a machine that was using nvidia hardware RAID 0 - but F10 had no problems with it.
View 1 Replies
View Related
Dec 10, 2010
There is a FC4 Server with A8V-MX mobo currently running 2x WD500 SATA drives in RAID1 with a third WD500 SATA drive for data backup. This machine has been running 24/7 since January 2007.The plan is to replace the WD500s with WD 2TB SATA II drives in a similar setup as above. i.e. 2 drives in RAID1 and the third drive for data backup.Definitely looking to do a clean Fedora 14 install on the 2TB but have some questions.
1. Will Fedora 14 detect the VT8251 connected SATA drives?
2. If not, how do I get drivers so it will? (I have the mobo CD with makedisk, but prob for windows)
I already have the 14 x86-64 DVD ready to go, but I am not yet at the site.the BIOS settings are: SATA, RAID or AHCI.
View 1 Replies
View Related
Jul 15, 2009
I have AMD athlon 64 processor, Seagate 160GB SATA Hard Disk, ASUS A8VMX mother board.With this configuration, I can Install FC7 without any error. But all the latest releases after FC7 is not detecting my Hard disk. Is there any solution to solve this problem? Actually I'm searching for a solution when the FC8 released. Now I have all the later releases from FC8 to FC11 DVD except FC9. But none is working .
View 1 Replies
View Related
May 28, 2011
ubuntu 8.04 server can not detect seagate sata hard drive 2tb or sata Lg dvdrw x22 sata drive .is it possible to install it without buying a pci ide sata card?is it possible to get a driver for sata driver and sata drive that can be recognise by ubunto 8.04 server ?or to get the files for 1.44 floppy diskdoes the late edition of unbutu recognise sate hdd and sata cdrw drive automaticly during the installation of the unbutu?
View 1 Replies
View Related
Jul 3, 2011
No SATA capable systems around the house to test this drive out, but with a SATA to USB converter I have been able to access SATA drives except this one particular Seagate drive. Upon connecting this drive dmesg shows
Code:
[173156.023440] usb 1-1.2.3: USB disconnect, device number 25
[173181.235788] usb 1-1.2.3: new high speed USB device number 26 using ehci_hcd
[code]...
View 14 Replies
View Related
Aug 13, 2010
Can SATA 3 (SATA III) Hard disk be run on motherboard which only supports SATA II, except sacrificing the speed (throughput)?
View 2 Replies
View Related
Sep 9, 2010
I went to install Ubuntu 10.04 on my home pc last night but I couldn't. The installers could not see my raid and even though I wished to install to a seperate HDD windows is installed to my raid. The windows MBR always overtook the Grub and whenever I start grub up it cannot find an OS or Kernel.
I have got an ASUS Rampage 3 Extreme [URL] and on it there are two 6.0 sata Marvell connectors: [URL]
In these two Marvell connectors are two WD velociraptor 10,00 rpm Raid 0 drives. On these two drives is installed Windows 7. The ubuntu installer cannot seem to see the raid pair and so does not install Grub correctly.
View 5 Replies
View Related
May 13, 2011
Just what the title says ... I'm trying to install Ubuntu 10.10 and it does not detect either 300G SATA drive in my system. One of them is /home for my non-OS software and the other is used for data storage.
It does detect the drive (SDC) where I have 9.04 installed, but /home is on one of the SATA drives. Where to start? 9.04 works just fine, but I'm running tio problems with FLASH web sites insisting I have to upgrade Flash and Adobe doesn't have anything for 9.04.
[Code]...
View 3 Replies
View Related
Dec 28, 2010
I have Mint 9 installed on a 120GB, WD SATA HDD. Now I want to install Ubuntu 10.10 on this HDD. Downloaded i386 desktop image and created a bootable USB stick with the image. System boots fine but installer do not detect My HDD. It only lists my USB drive. Even Gparted donot detect the drive. Typing sudo fdisk -l also lists only my USB Drive.
View 3 Replies
View Related
Mar 21, 2011
Ubuntu installer does not detect my sata drive during installation.
Hardware:
Asus p4gv-mx
4gb ram
250gb wd sataII drive
ide cdrom
Bios options tried:
Disabling apci 2.0
disabling apci
setting IDE mode to
[Enhanced]
[compatibility] w/both sata only, pata& sata settings
Setting my pata cdrom to slave and plugging it into the slave position of the ide ribbon.
I've tried these combinations with the usb installer, and dvd installer.
I've tried loading the live cd/dvd & usb then running the installer with in.
I've tried the spacebar method, hitting f6 and apci=no, noapci
The live cd has no problems detecting and mounting my hdd, however the installer does not detect it.
View 3 Replies
View Related
Aug 11, 2011
I'm trying to install Ubuntu 11.04 alongside Windows 7, but when I boot from the CD, Ubuntu refuses to detect the presence of Windows 7. I tried unplugging all my external hard drives to see if that made a difference, but Ubuntu still can't tell that I have Windows 7 on there.
View 4 Replies
View Related
May 31, 2011
I upgraded F14 to F15; However, F15 no longer recognizes my 3 sata disks connected through Marvell controller. The controller is an integrated Marvell chipset 88SE6480. The controller has its own manufacturer driver but it was intended for RHEL 5.4 (mv64xx) and installation of this driver fails to generate mv64xx driver.
View 3 Replies
View Related
Dec 4, 2010
just bought an adaptec 39160 PCI scsi controller and 34Gb drive and installed it on my computer.When i Booted it up a utility thing ran which said 'detecting array' and it found the drive and its size etc. it didn't go any further to allow my system to boot, so I rebooted and pressed CTRL + A to enter the adaptec scsi config. I changed something in there to make the disk non bootable (i Think) and rebooted the system.
It now hangs at :
'Detecting Array .....'
and does not show the drive details or the CTRL + A option to enter the utilities. So the only option I have had is to remove the adaptec controller ( and the system boots fine) the mother board is an Abit an8 ultra - probably about 4 years old and cpu is amd 64 I guess i have broken it and my remedy would be to reset the default options on the adaptec controller, but you can probably guess I have v. limited knowledge and have not used scsi before.
View 1 Replies
View Related
Feb 26, 2010
I have a sata card in my RHEL5 server that is not working. It has a 1.5tb hard drive attached to it that I would like to use. It seems that the 2.6.18 kernel did not detect and use it by default. I was able to find some info about the
lspci | grep VIA
03:06.0 RAID bus controller: VIA Technologies, Inc. VT6421 IDE RAID Controller (rev 50)
View 1 Replies
View Related
Mar 18, 2009
Recently i upgraded my dvd writer from pata to sata, now i install LG sata dvd writer into my system, now my problem is that its unable to detect in my fedora 8 box , but i can successfully boot fedora 8 from this dvd writer.i have a kernel version 2.6.23. solution for this.
View 8 Replies
View Related
Feb 21, 2010
I'm using the Ubuntu 9.10 alternate install CD in an external PATA USB CD drive to try to install Ubuntu on a ThinkPad X60. The installer boots but then very quickly gets to a stage where it complains that, "No Common CD-ROM drive was detected". It asks you to point out the drive or load or select drivers, but there aren't any drives or drivers to choose. I brought up another console, and looked in /dev, but there isn't anything there that resembles a CD drive.
I tried
$ modprobe ide-scsi
But it can't find the module.
I followed the instructions here, found the drivers on a working system, and put them on a thumbdrive. However, when I mount it:
$ mkdir /tmp/drive
$ mount /dev/sdc1 /tmp/drive
Mount fails due to an "invalid argument," with two different USB drives that work just fine on other systems. When even mount doesn't work, I feel like I've got both hands tied behind my back. How I can correctly implement the above command-line fixes? I'm not sure what I'm doing wrong. I've installed different Ubuntus probably a dozen times over the years, and haven't gotten stuck this badly since somewhere around version 4. Whether this problem is specifically related to the fact that my external USB CD drive has a PATA interface. If I go out and buy or borrow a SATA USB CD drive, is this problem likely to go away?
View 6 Replies
View Related
Mar 4, 2010
I've posted about this problem on a lot of similar threads and found nothing, so I'm creating a new one in the hopes of finally getting some answers.Ubuntu 9.10 never detected my two, IDE-controlled, non-RAID SATA drives. I never bothered to make it until the PATA drive that was running karmic died. Now I'm trying to dual-boot with my XP install on those SATA drives, but I can't get ubuntu to recognize them.Mobo: ASUS a8v-xe, North Bridge VIA K8T890, South Bridge VIA VT8251, Phoenix AwardBIOSHDs: one SATA 3.0 40 gB Maxtor drive, and one SATA 3.0 500 gB WD drive. The drives are not RAID, and the BIOS lists them as IDE-controlled.The install partitioner does not detect any drives. When I boot off of the live CD, neither GParted nor Disk utility detects them.I have tried each of the following, with no luck:
-removing DMRAID, both in Synaptic and Terminal
-installing with 8.10, 9.10 txt-alternate, and 10.04 Beta
-booting in expert mode with txt-alternate CD and disabling RAID
[code]....
View 7 Replies
View Related
Jun 26, 2015
“toshiba satellite u840w with hard disk drive and a solid state disk cache”
Debian 8 installer does not detect the hard drive during installation
I've recently tried to installed Debian 8. The problem is that the partition menu gives me these 3 options:
1. Configure iSCSI volumes
2. Undo changes to partitions
3. Finish partitioning and write changes to disk
There are no options for defining partitions or any hard drive during installation. After searching the internet i found that the problem because the solid state disk SSD cache. How I install a Debian 8 with computer which has a hard disk drive and a solid state disk cache.
more info: I want windows 7(64) and debian dual boot
View 14 Replies
View Related
Dec 1, 2014
I'm trying to install Debian Jessie beta2 on a UEFI laptop. The installation worked just fine before with setting in manual partitioning an EFI system partition and a root partition.But when I try to partition with root as an encrypted volume I get this error when I wanna write changes to disk:" the attempt to mount a file system with type vfat in scsi1 partition sda at /boot/efi failed"When I choose resume partitioning the installer then freezes at "detect file systems".
Because my harddrive needs specific alignment I've made beforehand in gdisk:EFI System Partition of 100mib at /dev/sda1/boot partition of 512mib at /dev/sda2/ (because I expect the installer to want a /boot too for an encrypted device)rest of harddrive reserved for root at /dev/sda3
View 3 Replies
View Related
