Fedora Installation :: FC10 Network Setup Repeatedly Overwritten?
Jan 21, 2009
Recent FC10 totally clean install. Fully updated using yum.
Using gui /system/administration/network I set up my DNS to the two IP addresses I've been given.
$service network restart
cat /etc/resolv.conf and the secondary DNS has changed to the IP address of my
gateway (router, at 192.168.2.x)
I.e. something is overwriting resolv.conf
Prior to this install, I'd been successfully using fixed IP on the 192.168.2.x range quite happily. Now it only works on DHCP and DNS seems to take an age.
View 4 Replies
ADVERTISEMENT
May 28, 2009
I have a home network with 2 WINXP machines and one I am trying to load FC10 on. If I get FC10 to work, I will convert the others to FC10. I am trying to access the WINXP machines through my LAN. I have installed samba. I have gone through a lot of places to try to configure samba. Several places say I have to set the security level on the ethernet card using system-config-securitylevel. When I enter this in terminal, I get command not found. I checked with yum and it is installed. I have tried using the menus but cannot find it anywhere. I can see the FC workgroup from one of the WINXP machines but I cannot look into it. It says I don't have the right permissions. I would like to set it so I don't need a userid/password at all. Can I do this?
View 5 Replies
View Related
Mar 21, 2009
I and my friend use FC10 on our laptops. We want to share our data by creating a wired network between our machines because a wireless router is something what our pockets can't afford. What should I do for it? What type of wires and stuffs do I need? I Googled for some link for doing so in FC10 but couldn't find.
View 6 Replies
View Related
Jun 1, 2011
Fedora-15-i386-DVD.iso file, sha256sum is correct. Burning by k3b on a fedora14 system fails again and again at 98.4% of the burning. I downloaded again to another partition and the same happens again. The k3b-debug output:
[Code]...
View 1 Replies
View Related
Jul 20, 2010
I need to play a info movie on a monitor through VGA. When done, then re-start the movie and continue to run it, forever. How do i do this? If I install a ubuntu 10.04 server, or a very stripped down ubuntu version (i dont know one) then how do I setup VLC to do what I want it to? All I can find is stuff about streaming over a network, and nothing on how to stream (local) over vga.
View 9 Replies
View Related
Jun 28, 2009
I have a lab of 10 computers with ips from 192.168.1.120 to 192.168.1.130 the server's Ip is 192.168.1.116When I am on client computer I type the server's Ip address on the browser and it works. All i want is that instead of entering my servers Ip I could just enter an address like: example.lan
View 3 Replies
View Related
Nov 27, 2009
I'm trying to upgrade to F11, and I'm having trouble. I attempted to download the x86_64 DVD .iso image by bit torrent, and it seemed okay, but when I started the installation the DVD failed the initial integrity check. I tried a second time with another DVD and got the same result.I tried running md5sum on the .iso image, but the response did not match what was in the CHECKSUM file that came with the .iso image -- should it? I tried downloading a live DVD image for comparison and found the same result - the response to the md5sum command did not match what was listed in the CHECKSUM file.Should these checksums match, or am I comparing apples and oranges? I thought the bit torrent client was supposed to check the files, but I'm not sure about that.
View 14 Replies
View Related
Jun 20, 2009
I'm having trouble getting my wifi devices to work on my 128bit WEP network. I have a new Thinkpad T400, with an internal Intel PRO/Wireless 5100 AGN. I also have some cardbus cards: a Lucent ORiNOCO Gold, a Linksys Wireless-G, and a TRENDnet TEW-421PC. I have them set up as interfaces eth2, eth1, and eth3. (The TRENDnet isn't recognised as a network card at all, so no interface for it.) I have installed the latest firmware for the Linksys card.
The /etc/sysconfig/network-scripts/ifcfg-* files are virtually identical for all of them, differing only in the HWADDR and DEVICE lines. So here's the behaviour:
1. The Lucent card comes up just fine.
2. The internal 5100AGN and the Linksys cards won't come up, and watching with iwconfig shows that they're either associated with my AP OR they've got an encryption key set -- but not both.
3. When trying to bring up the 5100AGN, I get the following messages:
iwlagn: index 0 not used in uCode key table
iwlagn: index 3 not used in uCode key table
/var/log/messages shows DHCPDISCOVER requests being sent, but they're bound to fail since the association with the AP with WEP isn't being completed. And yes, the ifcfg-* files really *are* identical except for the DEVICE and HWADDR lines. The /etc/udev/rules.d/70-persistent-net.rules file correctly maps the interfaces to the MAC addresses. So why does my antique ORiNOCO card work and thew newer ones fail? How can I track down what's being done wrong/not being done?
View 4 Replies
View Related
Sep 2, 2011
I have been trying to follow this guide for dnssec http://wiki.debian.org/DNSSEC in which at the very last it gives that you should change the value in /etc/resolv.conf to 127.0.0.1 Now in mine, network-manager overwrites the values. Is there a way to stop network-manager from overwriting the values in /etc/resolv.conf ?seems the simplest is to write-protect it. chattr +i /etc/resolv.conf
View 8 Replies
View Related
May 16, 2009
I'm going to setup a File and Printer Sharing in my little home network... 3 Computers actively connected to the Web through a single ADSL2+ Wireless Router (number of Computers will increase later) At the moment 2 of the computers are running Fedora 10 and 1 running Windows XP...
Now i want to setup the 3 machines to use 1 printer which is connected to one of the Fedora 10 machines, and i want File Sharing to be enabled so each machine can easily view each others shared files and also be able to print when ever needed (ofcourse the machine with the printer will have to be on for the printing process to happen) I've installed Samaba on each Fedora Machine, enabled sharing but i dont seem to be able to view the Windows machine or each other....
View 6 Replies
View Related
Mar 3, 2009
I have been running FC8 on this IBM T23 with a D-Link wireless adapter. Using MadWifi this has worked fine with Network Manager disabled. But now I have nuked that installation and replaced it with FC10. Network Manager is nice, and I would like to use it. And it kind-of works. Network Manager recognizes my router and all my neighbor's routers, but I can't connect.
[Code]....
View 5 Replies
View Related
Jan 6, 2009
When trying to launch firefox after upgrading to FC10, I get:Couldn't load XPCOM
View 4 Replies
View Related
Aug 6, 2009
I did the yum preupgrade install, all went well, did preupgrade -gui ; did everything fine, then i got the REBOOT now to start updating, clicked and i have just
View 5 Replies
View Related
Mar 30, 2009
I was forced to reinstall fc10 a couple of days back and from them the bootingup is really slow(takes more then 1 minute to show login screen). before the reinstall, it was quite fast. i dont know what went wrong.
[Code]....
View 2 Replies
View Related
Apr 16, 2009
I am trying to install systemc v2.1.0 on fc10 with gcc 4.3.2. I have gone through the previous posts for systemc installation with gcc 4.3.2 and have installed the patch ,
added the following headers in systemc-2.2.0/src/sysc/utils/sc_utils_ids.cpp
#include "string.h"
#include "cstdlib"
but it did not work out.This is what I get The complete installation process is as follows
$tar xvzf systemc-2.1.v1.tgz
$cd systemc-2.1.v1
$wget http://www.kix.in/misc/patch_systemc-2.1.v1-gcc4-osx // patch from post
$patch -p0<patch_systemc-2.1.v1-gcc4-osx
[code]....
View 1 Replies
View Related
May 3, 2009
After to download the firefox-3.0.10.tar.bz2I have the next problem
Code:
firefox-3.0.10]$ ./firefox
./run-mozilla.sh: ./firefox-bin: /lib/ld-linux.so.2: bad ELF interpreter:
[code]....
View 11 Replies
View Related
May 27, 2009
installing IE on FC10 as I need it to access company email I installed wine first as #yum install wine* then I installed cabextract as #yum install cabextract after that I downloaded IEs4linux and run the script ad $./ies4linux I got the following message in the terminal "IEs4Linux 2 is developed to be used with recent Wine versions (0.9.x). It seems that you are using an old version. It's recommended that you update your wine to the latest version (Go to: [URL])" and in the install window script couldn't download flash and it seems to be hang every thing is stopped and I didn't get any message in terminal or in installation window.
View 1 Replies
View Related
Jun 9, 2009
I'd like to try a clean install instead of an upgrade from FC10 to FC11. What is a good way of getting the list of all packages that were installed through yum, and how do I feed that list to yum on a newly installed FC11?
View 7 Replies
View Related
Sep 26, 2010
Having just installed OpenSuse 11.3, NetworkManager identifies my wireless network, but repeatedly fails to make a connection. Without further ado, here are the outputs to commands requested in the first sticky thread:
[Code]....
View 7 Replies
View Related
Apr 9, 2010
I installed Ubuntu on an old desktop last night and am having some problems with my wireless connection.I've searched around a bit and tried a few solutions but nothing seems to be working so hopefully someone can help. I'm using a Netgear WG111v3 wireless USB adapter and am attempting to connect to a Sky Broadband modem, the connection shows up in the list of avaliable networks after clicking on the network symbol and after attempting to connect for a while it then asks for the WPA password.
I enter the password and then this repeats over and over again continuously asking for the password and me continuously entering it. I know the password is correct as I'm using it on my laptop and other home computer right now.I've tried connecting to a hidden wireless network and inserting the network name and password as some have suggested and I've also tried adding the details from my router into the connection; so that I have manually entered the information rather than automatically finding it, this also hasn't worked.I should probably add that earlier today I seemingly randomly got connected and then managed to run some updates but since then it has disconnected and the same problem is repeating over and over. Sorry if thats quite a long explanation but I thought I'd try and make it as clear as possible,
View 1 Replies
View Related
Dec 10, 2009
How do I update from FC10 to Fedora 12 from the command line.
View 2 Replies
View Related
Jan 30, 2009
I have just loaded the FC9 onto a HP/Compaq D510 2.8Ghz/Intel graphic card. Everything when as expected during the install but on login I get the following set of errors. The follow Panels encounters a problem.
[Code].....
View 3 Replies
View Related
Feb 23, 2009
Just installed FC10 and noticed no sound with latest kernel (2.6.27.15-170.2.24), however I do have sound with kernel 2.6.27.5-117. No other differences. Anybody else have this problem?
View 10 Replies
View Related
Mar 3, 2009
I installed fedora on my second hdd, the other one had xp before fedora, now in grub it shows xp as other and wont boot into it, just hangs there. SDC is an external drive and sdb is the xp drive as you can tell by the filesystem.
Disk /dev/sda: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x836db2c4 .....
View 1 Replies
View Related
Mar 5, 2009
I am new to Fedora 10 and encountered the following problem. I installed FC10 on an external eSATA hard drive (sdb) on my laptop which already has some other Linux distros on sda. I used a DVD that came with the Fedora 10 Bible, so I can assume that the DVD had no problems. The installation went OK and I got no error messages. I added the following lines to the menu.lst file of the distro that I use to boot all my distros.
title Fedora 10
root (hd1,1)
kernel /boot/vmlinuz-2.6.27.15-170.2.24.fc10.i686 ro root=/dev/sdb2 rhgb quiet
initrd /boot/initrd-2.6.27.15-170.2.24.fc10.i686.img
When I boot Fedora, the blue bar at the bottom of the screen goes half-way, then gives me the error message: "mount: could not find filesystem '/dev/root' "
View 5 Replies
View Related
Apr 18, 2009
I would like to try out fc10 on an old, k6-2 pc. Last night I tried to download the dvd, but firefox 'completed' the download with only 1.2/~3xg, and of course it didn't work.
I am trying a test net installation in VirtualBox, so far so good.
However, I would rather have a more complete installation on hand and I'm looking at the full install cd's --there are 6 of them.
[url]
Are all 6 required for a minimal install, or could I get by with one (or two, etc)? For example, with debian installation cds you can use just the first one -- the rest are just a complete set of packages for everything +kitchen sink.
View 1 Replies
View Related
Apr 20, 2009
I upgraded to fedora 10 using yum but i have a problem, the installation went fine and after rebooting i got a login screen. I typed in my user name and password and after a second it returns to the login screen. Im sure the username and password are correct. If i type in another password i get an error message. So how can i log in?
This is what i did to upgrade to Fc10:
Code:
Then i got an upgrade wizzard and selected Fedora 10 and than reboot.
In the grub menu only one kernel is present which is the Fc10 so couldn't use the old one.
I've tried to edit the kernel with single for single user that works gives me a command line but im just not experienced enough to figure out how i can use the command line to login.
View 6 Replies
View Related
Apr 20, 2009
Anyone know where I can find installation driver disk for a RaidCore 5252? I do have the source code, would I be able to create a new driver for this controller? If so, how is that done?
View 2 Replies
View Related
Jun 1, 2009
My laptop is dual-boot with Windows XP and FC10 co-existing. Yesterday, I wanna re-install FC10, so I formated(deleted) all linux partitions in Windows XP. Disaster happened when i rebooted computer: the computer cannot startup at all?Now, I don't know how to deal with it. I wanna know: what can i do to start up the computer into Windows? In my opinion, computer should work well without one system in dual-boot mode. If you format C: drive on which windows are installed, for instance, the computer can boot into FC10 normally. Why it die deleting FC10?
View 1 Replies
View Related
Jun 22, 2009
I've been running FC10 with all updates and had downloaded the FC11 DVD. Yesterday I upgraded to FC 11 using the DVD and it appeared that everything went fine. However when I tried to do ayum updateI got the following error. There was a problem importing one of the Python modules required to run yum. The error leading to this problem was:
No module named yum
install a package which provides this module, or verify that the module is installed correctly.
It's possible that the above module doesn't match the current version of Python, which is:
2.6 (r26:66714, Mar 17 2009, 11:44:14)
[GCC 4.4.0 20090313 (Red Hat 4.4.0-0.26)]
go to the yum faq at: [URL] I'm not sure what to do next. I also noticed that all my previously configured repositories are lost.
View 3 Replies
View Related
