Fedora Installation :: 14 Live CD Freezes On Boot Probing PCMCIA Slot?
Apr 3, 2011
I have a Toshiba a105-s2236 laptop and am trying to install Fedora 14. Is there any way to tell Fedora not to look for the pcmcia slots on boot? My live CD is freezing at the point where it tries to probe the pcmcia socket IO port.
I tried adding the 3 to get to a console, but that fails as well. I had to add acpi=off to the kernel boot args to even get it to go this far.
Even using the nopcmcia option, it still tries to probe the socket's IO port.
The Fedora 12 (64 bit) install freezes right after the "probing EDD (edd=off) .... ok" comes up. I have to do a hard reboot to get the system back. I am currently running Fedora 8 (64bit) and everything works fine. The Fedora 11 (64 bit) install runs. (I don't really want Fedora 11, so I didn't complete the install). The Fedora 12 (32 bit) install runs. (I don't really want 32bit Fedora, so ...). The Fedora 12 (64 bit) install only runs if I add mem=xxx. (I would like to be on this version)
I'll be doing the full install soon, but what should I look for once I have it installed to figure out what the issue is? Why do I now have to pass the memory size when 8 and 11 seems to be able to figure that out? I have a dell optiplex 740 with 4Gb of ram. AMD Athlon x2 64bit processor.
I tried to install Fedora 10 with an encrypted root-filesystem on my Laptop. The problem was, that I wanted to install to the second hdd which resides in the extension slot of the laptop. I can either have the dvd-drive or the hdd in the slot. So I removed the internal hdd, and inserted the second one in its place. That way I could use the dvd. The installation went fine and I could boot into the OS. Then I removed the hdd again and inserted the original hdd to the internal slot, and the fedora-hdd in the extension slot. I can select during power-on from which hdd i want to boot, but I cannot boot fedora. After the first dialog, where I can enter the password to decrypt the disk, I get an error message (something like drive not found). I tried to change the grub settings in the /boot partition (which is not encrypted), but without success.
So, is there a way to boot the system? Or how do I install Fedora on the second hdd without the dvd-drive?
im building a storage pod following the backblaze build url. This build requires two power sources. One powers the boot drive, the mother board and 20 of the hard drives while the other powers the remaining 25 drives. When I power up the 25 drives first and the boot drive etc 2nd I recieve the message "Probing edd=off to disable" the system then freezes there. If I power up the boot drive etc then the 25 drives then it boots up normally with no problems. When ever I restart I recieve the same message since the 25 drives are already running when it boots.
I dont want to add edd=off to the boot command since i cannot have some drives not being detected all the time in my raid configurations. I have tried updating the bios and that didnt help. I have also installed a different os and receive the same message.
I am running Linux version 2.6.26-2-amd64 (Debian 2.6.26-21lenny4)Motherboard: Intel BOXDG43NB LGA 775 G43 ATX Motherboard
All of my specs are the same as the ones listed in the Backblaze build.
I am attempting to get Debian+Mate running on my laptop, with no success. I have not yet used Linux, but I do wish to climb out of the Window, and the Live session seems ideal to get a feel for Debian before finally abandoning Windows.
I got the Debian+Mate ISO file from the Debian website, and created a bootable USB stick. (Note : I have done this several times, getting new ISOs, and using Unetbootin, Universal USB Installer, and Linux Live installer; the result is always the same.)
When I boot the USB drive, all appears good at first. I get to the Debian (or Mate?) screen which is a pale jade green with a white squiggle in the middle region, with a panel at the top; this shows at left three options - applications, places, and system; and at right the correct time, a sound symbol,the wifi symbol, and a battery indicator. At the left of the screen in vertical arrangement there are 4 icons labelled computer, users home, install Debian Sid, and trash. On the bottom panel, at left there is a "button" for "click to hide all windows & show desktop", and at right 4 squares for workspaces.
There are also (temporary) windows that inform me that the battery is no good (I run on mains), and that there is no wifi connection established. These windows disappear in a minute or so.
The cursor moves ok. The only actions that it creates are the information drop-down texts that tell me what the headings mean - e.g. no connections when I hover the cursor above the wifi connections symbol.
But whatever I attempt to do - selecting any of the options - nothing happens. Everything except the cursor appears to be dead.
The machine that I am using is an old laptop that I use as a second computer. It has a SIS Mirage 3 graphics engine, which I gather may be a problem. I also tried the same procedure with my fairly modern ASUS laptop (NVidia graphics) with exactly the same results; it seems that NVidia graphics may also be problematic, judging from some posts on the web. I have also tried Debian+Cinnamon, again with the same outcome.
I run plop bootmanager - [url] to load live linux distros from the usb drive on the PCMCIA card. This is because grub2 doesn't yet support the pcmcia drivers and I wanted to make use of my old laptop.
I run the instruction on how one should install ubuntu on a usb stick from [url].
The process goes through when I see the live CD screen where it lets me try Ubuntu without installing. The splash screen comes up and all and remains there for sometime but after that it stops and then I get this error:
Its trying to search for my cdrom drive when it shouldn't as I have it on usb drive!
I am trying to find out what's my soundcard model as my sound is not working very well.I am using YasT2 - > Hardware Information to find out what is the problem. The probing hardware process starts but gets stuck at the probing monitor phase (49%). I have tried to rerun the process after rebooting the pc. I have let the process to run for a few hours but still it was stuck at the 49%What should I try to do to skip this obstacle and get information about my sound hardware.
I have just installed F10 via DVD download onto my Dell Desktop with Nvidia GE6800 graphics card and twin LCD Monitors. I have configured Dual Boot with Grub (Windows XP Home and F10). After installing and configuring the correct driver from Nvidia I am now observing a strange problem when booting into Fedora.
On cold boot the system starts and gets to Probing EDD (edd=off to disable)... and then freezes, however if I then warm boot Ctrl Alt Del the system boots into F10 with no problem. I had to disable the latest Kernel update because I couldn't start graphical interface with it so I only boot into the original Kernel.
I have a sandisk cruzer 4gb and everytime i try to boot with it in the usb slot it doesn't get read. after bootup i have to pull it out and put it back in and then it recognizes and reads it. have usb device selected as first boot order and have even hit esc during bootup and selected usb as boot device. trying to install the unbuntu 10.10 on the netbook.
Probing EDD (edd=off to disable) .... then the boot hang up for a few minutes with a flashing cursor immediately after the message and finally it booted the default OpenSuse 11.1 in the usual way. I tried to search LQ, Wikipedia, Google... but even if the message has been reported by many people, nobody gave the answer to the question running in my mind:
Code:
What is EDD? Should I start to think about the funeral for my beloved notebook? Should I consider to do an additional backup copy of the backup of my disk, just for sure?
Tried the DVD install for 10. Install went fine other than it take for freakin ever, but after an 1 hour install, the update wanted to install 1675 or so updates. I let those updates install. 5 hours later the updates were done. Rebooted and now it freezes at a blank screen right after the 3 scrolling bars. System is older AMD 3000+, 1 GIG RAM with NVidia 5700 video card.
I did try and search some. But the only thing I could find was something about editing my grub file for a scan=sync setting (the information was basically gibberish to me. No clue what it was talking about or how I would edit a file on a system that won't boot). I tried to recover mode off the live CD. It had some options that said you could type Linux command line arguments, but whenever it got to the sysimage it says Linux isn't a command.
I already know what the problem is, which is that I have an AGP Nvidia graphic card. When I try to boot the live cd it freezes. I've done some research and I've already tried using "nouveau.noagp=1" as a Boot Option from the live cd. But it says unknown boot option ignoring. And it still fails to boot up. Im anxious to begin using Fedora.
When it is trying to boot...it also says IO APIC resources could not be allocated.
I get it to boot to the loading screen and it gets to what looks like 99% loaded and it just sticks, i have tried multiple downloads, different cds and did "verify and boot" just to be sure and it just sticks and does nothing?
Just read up that it's an issue for a lot of others as well, so i'm downloading the dvd to do a straight install from
I'm trying to install using live USB stick. The F15 live CD was downloaded and copied to the USB stick via liveusb-creator. The target machine has Award BIOS v6.00PG, I set the first boot device to USB-HDD. When I tried to boot it from the machine, I get the following error:
SYSLINUX 4.02 2010-07-21 CHS Copyright (C) 1994-2010 H. Peter Anvin et al ERROR: No configuration file found No DEFAULT or UI configuration directive found!
I'm trying to install F11 in my new laptop [URL] and I'm unfortunately about to give up, but I want to give this option. What I want to do is use the live cd (on a usb stick) to boot on a text-only session. Supposedly the way to do that is type "linux text" on the boot prompt but the problem is that I can't even get there. After booting I get the grub menu with two options: boot, and verify and boot. Hitting esc doesn't bring me to the boot prompt. I can get to the grub menu, but I'm not sure what to do from there. And I can edit the boot and kernel options, but I'm not sure whether that will allow me to log in a text-only session.
I currently dual-boot Windows Vista and Suse 11.2 on my Gateway desktop machine. I'd like to try out Fedora in a triple-boot situation.
My trouble is that the F13 Live CD hangs during boot. I've checked the hashes of the downloaded ISO files, and done burns on multiple media. During booting with the Live CD, my box hangs and I have to use the physical power button to turn off the box.
I've tried the 64-bit KDE spin (my preferred choice), the 64-bit GNOME version, and also the 32-bit KDE spin, and all of them hang at the same point. Removing the "quiet" boot option shows that it hangs after setting up my built-in card reader. When I installed Suse 10.3 on this same machine, I had to use the flags "acpi=off" and "brokenmodules=pata_it821x". Would the syntax be the same if I wanted to try with those boot options with the F13 Live CD?
Using the ISO files in VirtualBox inside my working Suse install works just fine.
I was running 10.04 with no problems. Upgraded. I may or may not have lost power before the upgrade was finished. Now my system locks out the keyboard and mouse on the login screen...nocapslock light or anything, but I know it's still running because the clock at the bottom increments once per minute. Booting safemode does not help, it simply hangs at some point on the scrolling black screen instead.I can boot 9.04, which is still installed on another partition, just fine.Is there any way I can boot to a terminal and try running apt-get again, to see if I can fix whatever's wrong?
When i boot the fedora image from a dvd i'm not being taken to the fedora live system screen, instead i see a bunch a words on a black screen (looks like DOS)...am i having compatibility issues or what? ive tried 32bit, 64bit versions as well as different desktops. does anyone have any ideas? my laptop is brand new: toshiba e205 running windows 7 ultimate..
i have a hp dv6707us with windows vista and i'm trying to install fedora 10 x86_64 from a live cd, when i try to use the live cd it shows a screen saying that it will boot after 10 seconds, then appears a black screen with a loading bar with fedora 10 word next to it when the bar becomes completely white along with the word fedora 10 it doesnt happens anything and any indication of what could be wrong then i type enter and it reads the live cd for a while then a black screen with a blinking cursor appears and yet nothing happens i wait until i get bored and cancel the all the process.
I'm making life difficult for myself. Summary, I have a laptop with F10 installed on a portable harddrive (sdb 1-3, i.e., no logical volume) Works great, no complaints so I guess this reduces to a grub question; how do I edit grub.conf to boot an iso on sdb4? Fedora10.iso for example.
Yesterday, i just got my Fedora live DVD. When i tried to boot it from my CD/DVD ROM drive, it seems to hang when it's just about to finish loading. From one of the prevous threads, one of the members said that i had to have 2 partitions on my HD. Currently, i already have 2 partitions. Can someone give me advice on what to do??
I was using Ubuntu 9.10, until I got a new graphics card (Nvidia GeForce 9800 GT). After I got that upgrade, Ubuntu no longer supported that card for some reason, so I decided to try Linux Mint since it was a close relative to Ubuntu. Still no support for the video card.
I've always wanted to try Fedora so I decided to grab the x86_64 live cd and burn it. I stick it into my disk drive and it boots where it shows me the options to "Boot" "Verify and Boot" "Boot from Hard Disk" and one other option.
I tried the Boot option, and after selecting that, everything stalls, and my display turns off (not the entire monitor, just the display). I tried Verify and Boot, and still no luck.
I have also tried the i686 live cd and the same issue. It can not be the way I am burning it, cause I've gotten other live cd's to work with the same method of burning. Is it that Fedora does not support the card?
I am trying to get the GNOME version up and running.
I want to dual boot Fedora 11 and Windows Vista, and the last time I tried I deleted my Windows Vista (big no no). So, I've made a partition of about 30GB, and I'm trying to go through the installation (from the live CD), but I don't know quite what to do? If I select Shrink existing disk, it doesn't let me do it for any amount that I put in, by the way.
I was able to install Fedora 10 from the Live KDE CD, however I can't boot it.
I placed it on /dev/hda4 of an IDE disk, while on /dev/hda1 I have a RedHat 9 Linux, /home is on /dev/hda2 and the swap is on /dev/hda3. I'm not sure if RedHat 9 and Fedora 10 can coexist on the same HD.
There's an option in the Live KDE CD boot install, which allows one to select:
boot from hard disk:
Do you know what to type in in order to direct Fedora to boot from /dev/hda4 (who may be /dev/sda4 as seen by Fedora)?
P.S. For the time being, I want to forget about Grub or LILO and see if I can boot it this way first. I have LILO working, it boots Windows from a separate disk and RedHat 9 from /dev/hda1.
Well Fedora 14 sees my Emu soundcard right out of the gate with the live cd! I have windows 7 installed right now. I would like to install Fedora 14 from the live cd to have a duel boot setup. What I am trying to do is just give Fedora 60GB of the drive and keep the rest for Winows. How can I go about this with the live cd. I am sure it's been covered to death but I couldn't really find it.
I'd like to install Fedora 14 64bit as a dual boot on an existing win 7 32bit system. When I boot with the Live CD, after selecting "boot" in the Fedora boot selection menu, I get a grey screen with a white cursor, and the system freezes. I checked the Live CD on my laptop and it worked perfectly.
My System: MotherboardASUS P5Q DELUXE CPUIntel Core 2 Duo E6750, 2,66 GHz, Sockel 775
I am running Vista on my C: drive and I just got Fedora 11. I planned to dual boot Vista and fedora 11. I Downloaded the Live CD from the site (680 +- MB) and burned the files IN the .iso file to an empty DVD and CD. Shrank my D: drive and now have about 27 GiB wort of unpartitioned space. I booted from the Live CD. everything went OK until i chose Boot from the Boot Menu that came up. First it took me to a screen with the following message:
ACPI: expecting a [reference] package element found type 5. and then in went on to boot normally. Then when it reached the user login screen, I found that my mouse and keyboard were'nt responding and that there was no lights on any of the keys. I checked the USB cables and did a hard shutdown and booted from the Live CD again, but the problem persists.
I've run the install to hard drive program three times over and each time I get "disk boot failure". I believe I've got Grub to install to the mbr but I am not sure.
System: Barton 3200+ with 1GB of DDR1 Asus A7V333 High Point hard disk controller
other items
All the hard drives are hooked to the High Point controller. It recognizes all of them that have power hooked up and read/writes to them. Two have 98SE installs, the third is where I'm trying to install Fedora 12 to get away from some problems I'm having with 98SE.
The BIOS is set up to boot from the "SCSI device" which means it's booting from the High Point controller. The High Point lets me set a boot mark, which, when set to the Fedora drive, yields the disk boot failure no matter what I do to it.
