I'm trying to install F11 on my old FSC Amilo Pro laptop. The installer starts fine, shows up on the screen fine, but the graphic installation window is wrongly positioned on the screen. It's about 300px too far to the right and about 300px too low on the screen, so that my Next, Back, Cancel buttons etc are off the screen.
View 2 RepliesI have installed Ubuntu 11.04 along side windows 7 ultimate. But the problem is as soon as I switch on my computer. There is only a blank screen with my TFT screen displaying a msg "Out of Range"
Then suddenly Ubuntu loads without showing any option to load windows 7.
I have an asus netbook with an intel GMA integrated chip. until now i had been using the out of the box drivers, hadn't changed anything, and it worked ok. I tried installing a graphics driver and rebooted. This time i got the command line only, logged in, uninstalled the driver (apt-get remove) and rebooted, now after i choose ubuntu in GRUB an instant after the ubuntu loading screen comes on it goes to black. I'm trying to find a way from within GRUB to get it to do a command-line boot so i could force it to use the default drivers (how would i do this exactly?), but when i press "e" and then put "text" at the end of the "kernel" line it doesn't change anything. so what do i do from here? worst case scenario i reinstall ubuntu.
View 2 Replies View RelatedGot an Asus eeepc 900a. Runs Intel 915 graphics. Upgraded to slackware current last week. X would not start. Based on info here, I reverted back to earlier libdrm and xf86-video-intel. That got it working again.
Updated Slackware current again today. I think I got a new kernel. Now, halfway through boot time, the screen goes blank, then comes back and the font is tiny. Gone into framebuffer mode. If I start X, it just freezes. Nothing but a reboot will get out of it.
I have vga=normal in lilo.conf, but I read that this is no longer used. I can find no way to turn off framebuffer mode. From other threads here, I have tried append="i915.modeset=1" in lilo.conf. Has no effect.
I could revert Slackware to 13.0 from current, and that would make the eeepc useful again. Is there anything else I should try?
Code:
Fedora 12
2.6.32.9-70.fc12.i686
GEFORCE GO 7400
When my notebook boots I get a high screen resolution. However, when I login it seems to go to a lower resolution that is not clear. I think this all started when I updated to a new kernel. So I reinstalled the nvida drivers using leigh's guide. However, I still can't seem to get it to display correctly.
Code:
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (mockbuild@) Sun Feb 28 14:49:02 EST 2010
# Xorg configuration created by livna-config-display
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection .....
I my trying to install Ubuntu onto a new 1 TByte Sata HDD on my Dell 8400. The computer has no other OS installed as the old HDD containing Windows XP has being removed. The new hdd has being fully formatted and is set up as a NTFS with a single partition of 1 TByte. I downloaded the latest version of UBuntu and burned it to a cd as a ISO file. When I boot my computer up from this cd I am asked to enter my language of choice and then I get the main menu screen. On this screen I choose option (2) - Install Ubuntu. After a few minutes during which time you can hear the cd being accessed the screen just displays this main menu and never changes. I have tried twice using this install option but after 45-50 minutes the screen still never changes. No progress information is given. If it is normal how long does the installation generally take?
View 2 Replies View RelatedI can't seem to get Ubuntu to run on my old Dell Dimension 2300. It boots to a purple screen then it goes to a black screen with a load of writing nothing else happens after this screen. [URL] Could someone advise how I can get it to work?
View 1 Replies View RelatedI am new to linux go easy please. I have about 200 machines with opensuse11.4 KDE on them, I would like certain information to stick to the background kinda like a widget type of thing that cannot be removed by a user (no admin rights) and it has to start on machine boot up and also these pcs are continually moving to different spots in our building but on the same network so idk if that changes anything with configuring the ip address.... the only things that need to be visible are as follows:
Host name
User name
IP address
domain
So basically widgets are useless to me, unless somebody knows how to configure these the way I need them or maybe there is something better then widgets. I came here to get the right answer from all you geniuses out there instead of trying to hop around on google and whatnot. Let me know what my options are and how I can roll this out on 200 PC efficiently.
I compiled the buildroot for zImage and rootfs.jffs2 for SMDK6410. Used the linux kernel 2.6.35 and busybox 1.17. And deployed these two images using DNW. The kernel and rootfs loaded successfully and able to do execute linux commands from DNW but not from LCD screen. I am new to the linux development and want to see a sample framebuffer / desktop application on the screen.
View 2 Replies View RelatedI have a little brother who is handicapped and uses the machine he was sat by the computer with a blank screen at which point my dad soft rebooted the machine (he will sit at the machine if its not working but he cant tell us its not working). I don't know if the below caused the machine to stop displaying?
Code:
New to ubuntu, as of about 3 days ago. Using ubuntu 9.10 on a Dell Dimension 3100. I installed ubuntu as a program on windows 7. I am only given the option for 800X600 and wanting to switch to 1024X768. My graph card is MESA DRI Intel 915G GEM 20090712 2009Q2 RC3/x86/MMX/SSE2 v1.4 Mesa 7.6. Other info: The X.ORG Foundation v1.6.4. How can I get the desired screen resolution?
View 1 Replies View RelatedI use Ubuntu 10.04 LTS.
I was compiling an application called Audacious. One of the dependent packages I needed to obtain was called Glib. After installing Glib (and a package it also required), my GNOME began failing and after rebooting the computer, the login GNOME login screen fails to displaying. Does anyone know what's gone wrong?
[URL]
Now after installing Glib, restart your computer and your GNOME will have failed. Why the F did this happen?
For the past month or so I have been having some issues with screen crashing and displaying funky colors. Basically it happens at completely random times, doing completely random things. The screen goes to a pink color then freezes the the only way I can gain control again is if I restart the machine or restart gdm via ssh. This is really puzzling me. Perhaps there are some logs I can look at? A little bit about my system:
Code:
Processor2x Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz
Memory4059MB (1321MB used)
Display[code].....
To redirect standard output to multiple files:
Code:
echo Test | tee file1 file2
My problem is that the word "Test" still displays to the screen? I want same effect as:
Code:
echo Test > file1
but with multiple file redirection.
For the past month or so I have been having some issues with screen crashing and displaying funky colors. Basically it happens at completely random times, doing completely random things. The screen goes to a pink color then freezes the the only way I can gain control again is if I restart the machine or restart gdm via ssh. This is really puzzling me. Perhaps there are some logs I can look at? A little bit about my system:
[Code]....
Since I have upgraded to Lucid (and thus to Mozilla 3.6.6), I am experiencing a bunch of annoyances with Mozilla.
1) logging into my GoDaddy account keeps displaying the login screen and not my accounts page (yes, I checked the password)
2) creating an account in bugzilla resulted in an "Invalid OpenID transaction" error message instead of a confirmation page
3) the [URL] page popped up a parser error instead of the website.
Midori and Mozilla 3.0.8 work just fine. Does anybody else have problems with mozilla 3.6.6 and above?
HP Pavilion Media Center a1430n Desktop PC
Athlon 64 X2 (T) 3800+ 2.0 GHz
Asus A8N-LA chipset GeForce 6150 LE
1 gB of RAM
Video Graphics: integrated
Hipro hp-d3057f3r max out put 300w
Here is the problem fist i had a 8800gt installed it work fine until one time the card stop displaying on my screen and the card would make a fan sound like if was over heated......but my integrated still displays... ok then i send the card to my provider so it can be replace.. so they send me a 8800gts .... and i installed and deleted the old drives and even upgrade my bios .... but still happen like it happen whit the 8800gt it wont display any thing on my screen and also is making the same fan sound of the 8800gt ....
I have been using ubuntu wel a long time now and I know my way around in linux but I recently updated my laptop from ubuntu 10.04 to ubuntu 10.10 all went fine until I had to restart my laptop. I got a purple screen (loading screen) with 4 dots and a oldskool like font which said: Ubuntu 10.10 Right after that the screen goes purple and its like the system halts I hear no login sound etc just a purple screen. So I did a clean install from the 10.10 live cd which booted perfectly fine and the system was also useable like before. But when I installed the system and rebooted it again no problems.
But when I tried to install the proprietary nvidia driver (the recommended one) I got the same problem again the purple screen. After searching a while on the internet I only found posts which had the problem with ATI cards but my laptop is fitted with a Nvidia Geforce 9300 M card. So I tried several things like removing the xorg.conf (read it somewhere) which ofcourse did not work, and booting in graphics fail safe mode which worked. So the point is in 10.04 and 9.10 I CAN use my video card drivers but not in 10.10 is there a solution to this problem? I am talking about the 32 bit version of ubuntu and here's my system hardware profile:
Intel core 2 duo t7350 @ 2,0 ghz / 3mb l2 cache
2 GB DDR3 ram
160 gb hdd
Nvidia 9300m gs
Chipset: I dont know sorry
Model: Samsung R710
Is there a known problem with the Lubuntu 10.10 image here? I have downloaded it to two different computers, then burned the images to two different blank CD's (different brands) and neither loads. Both only get as far as the Lubuntu menu, once ENTER is pressed at that point to load the LiveCD, a blank screen eventually appears with a flashing cursor at the upper left of the screen, that's it. They were both burned using the slowest burn speeds available.
View 9 Replies View RelatedWhen I install Ubuntu 11.04 with Wubi, I get this freeze screen after I reboot and get past the Ubuntu splash screen: url
As you can see, it's a scrambled picture of my Windows desktop. This happens with every other version of Ubuntu also.
I'm running a 64-bit PC and I don't wanna waste another CD or use a USB to install, because I actually progress further in my efforts whenever I use Wubi.
'm trying to duel boot windows 7 and ubuntu 11.04 on an Acer Aspire 5736, but when I try to boot from the cd (which I burned with InfraRecorder) it first goes to a black screen with a blinking under score in the corner, then to a purple screen with a couple symbols at the bottom, and then the screen goes black and nothing else ever happens
View 4 Replies View RelatedAfter succesfully installing Ubuntu 10.4 x32 and rebooting pc hangs on black screen with a flashing white dot in the top left corner of my screen, i've tried installing it twice with the same results.
my setup is: Asus p5q-e,
4 gig of corsair dual ram,
ati 4850 graphics,
onboard audio.
ahci mode
win 7 installed on intel ssd, and xp on a samsung 320 gb sata 2,
i had this configuration running fine for 2 months without boot loaders,
on pc start up i choose from which hdd to boot from.
i installed ubuntu on the samsung drive where it was recognised fine, wiped it all and installed automatically.
pls let me know if there is anything i missed, and advice if possible in what to do.
thanks
kannanni
another post about this. I just don't know how to handle this, as I'm pretty nsee the grub loading menu, but screen just freezes after, no way I can reboot, or open a console. In recovery mode I can log as root in console, though.I run Debian 6, 64 bits. I have an intel q6600 and a nvidia geforce 9800GX2.
View 9 Replies View RelatedI received the Ubuntu CD by mail the other day and tried to install a dual boot with it. I first tried it out by running from the CD and the first problem I had was the screen froze after the splash screen. So I lurked around for a bit and found out that I can press any key on the screen with the keyboard and person to get to a different screen. At this screen I entered "F6" and then entered "nomodeset", this allowed me to pass the splash screen.
Next, I got into Unbuntu but I found out that the keyboard and mouse weren't working, so I lurked again and found out that I have to enter "noacpi" (sorry if I got that wrong, I forgot the name ). I ran by CD once more and everything worked, so I decided to finally install it next to my Vista. However, after installing it goes straight to the splash screen, and the freezing happens again. The screen where the keyboard and the person are not showing up so I have no idea how add the "nomodeset" and "noacpi". So my question is, how do I get to the screen where I can add both those things? Also, is there a way to add it permanently so I don't have to keep pressing F6?
I downloaded Fedora-14-i686-Live-Desktop.iso and used the Fedora liveusb-creator to put this on a 2GB USB stick. Everything seemed to have gone well and it said complete; however, when I try to boot from the USB stick, I get a black screen with a linux copyright notice at the top and it just stays at that screen forever. I tried this on two computers with the same results.
I'd previously tried with Ubuntu and had a similar issue, it would go to a purple (if I remember correctly) Ubuntu screen and it sat that forever.
I running 1 pc touchsmart IQ816 (windows7, standalone) and a sunfire server (fedora 14, standalone).Because my touchsmart screen doesnt support dual screen input, i'm reaching my server true vnc. Is there a beter way (VMware?) to handle this problem?Im new in VMware: Can a esxi server from vmware help me out in this situation?
Do some people have experience on this?
I have downloaded ubuntu 10.10 64bit and have also burned it to good disk at 4x speed. when i boot it from cd everything goes simple and fine till it comes to a mixed orange colour screen and then nothing goes further, it just halts there with this full blank screen. so i have to do a hard shutdown. then i tried wubi.it went good. after rebooting it asks for installation options. there are five of them. in the normal mode the same thing gets repeated again. but in safe graphics mode ubuntu gets installed but few errors are shown after installation. there is no graphical screen and only this text screen comes again and again.
My laptop specs are as follows:
I have been running 10.04 quite successfully, when I upgraded to 10.10, I have a problem with the newer kernels. If I let it boot into the latest one 2.6.35-23, I get the Ubuntu 10.10 splash screen for a second then a blank screen, same with 2.6.35-22. I have to run with 32-25 to get it to load the gui.
I have an AMD Sempron 2800, 1.6GHz pc, but I'm not sure if it's running 64bit.
I've been running Ubuntu 10.10 very smoothly for a while now. Decided to upgrade to 11.04 - managed to corrupt the hard disk the first time by letting the laptop hibernate part of the way through but reinstalled from a live CD of 11.04 and it's now working except for this issue.
If I shut the screen on my laptop (or press the screen off button) either the screen won't come back on or it will but frozen (I can move the mouse but not click on anything etc.) In this state music continues to play (from spotify under wine) and if I press my hibernate shortcut (power button) the computer hibernates, only to wake into the same situation. I've got a Dell Latitude D520, upgraded to a bigger hard disk and more ram - the ubuntu partition has 50gb. Windows is working fine.
Edit: I noticed a sticky thread which includes something about a blank screen but I think this is a different issue?
This problem started within the last few minutes. I run a program in my browser that uploads data from my machine (ubuntu) to another machine (Fedora 13), for manipulation and then spits back the data that does not match our standardised information.
When I tried to run it a few minutes ago, it seemed to take a long time to make the connection. I went back and checked the machine, everything was connected and fine. I decided to reboot the machine from within KDE and then try again. Same result. I went to the machine again and tried to login through KDE, the screen goes black for a few seconds and then returns me to the login screen. I switched over to a virtual terminal and was able to login using the same credentials. I checked the .xsessions-errors file and this is what I am seeing:
[Code]....