I've just isntalled Debian 5.04 + Xfce. During the install, i didn't have the ADSL modem connected, therefore i didn't configure the network. Now I connect it but it doesn't work, Debian just won't recognize it. According to various guides I shouldn't need to do anything for it to work, so that's why I'm here.
View 4 RepliesI am having opensuse 11.0 installed. I have BSNL BB plan with "Always on" connection. How to configure internet connection in opensuse11.0 ?
View 1 Replies View RelatedI am using TATA Photon usb internet stick. It's a Huawei USB modem. OpenSuSe detects and shows it as mobile broadband. But can not connect to internet. Any1 has configured similar device before? It shows me in "network manager" but no option to active/connect it. In Windows I got auto dialer for Photon. And customer care says no support for Linux.
View 2 Replies View RelatedI am using both suse linux and scientific linux 4.6. my ether net card is RTL8111/8168B PCI Gigait.In suse i can configure internet and its working fine.
1. How to configure network in scientific linux 4.6 ? which driver should i install ? i don't find any driver corresponding to to this Ethernet card.
2.how to configure epiphany web browser in suse 11.0 ? it is not working.
I'm trying to configure internet access using KDE network manager. Added new VPN pptp connection, set gateway and other options but manager tries to connect for about a minute and breaks then. Here is /var/log/daemon.log
Code:
Jul 1 17:35:22 dvinokurov-desktop NetworkManager: <info> Starting VPN service 'org.freedesktop.NetworkManager.pptp'...
Jul 1 17:35:22 dvinokurov-desktop NetworkManager: <info> VPN service 'org.freedesktop.NetworkManager.pptp' started
[Code]....
As I understand the main problem is in "(IP Config Get) timeout exceeded".
Configuration: Kubuntu 10.04 x86, VPN server with MSCHAPV2 auth, no compression, no encrypting.
As i describe the thread,i won't be able to configure my NIC to connect to internet which is basically done by just running system-config-network in shell to configure xDSL connection.But instead of system-config-network it contains system-config-network-tui which is used for ISDN connection.And after running system-config-network as well as system-config-network-tui it shows the same output which is in attach file
After some google search it shows that there is bug with system-config-network and it is fixed in system-config-network-1.6.0.el6.2-1.el6 but i wont be able to find it.
As i m not subscribed to RHN
I use openSUSE 11.1 and my YAST can't connect Internet: How to configure my YAST Internet configuration through proxy server in order to download and install the programs (for example dwnld and install WML from [URL])
View 9 Replies View RelatedI have just installed Debian Squeeze on my spare computer (dual booted with Ubuntu 11.04) and I cannot connect to the internet using Squeeze. Due to my ISP, I have to manually connect this computer and on Ubuntu copying and pasting a text file such as this into the terminal works with no problems.What do I need to do to manually configure my Squeeze internet connection?
View 5 Replies View RelatedI will see ipcam in my local network from my tablets. I'm install server/client but I can't even ping my Ipcam from my tablet.I'm ping my ipcam from my server
Code: Select allping 10.42.0.22
PING 10.42.0.22 (10.42.0.22) 56(84) bytes of data.
64 bytes from 10.42.0.22: icmp_seq=1 ttl=64 time=0.639 ms
eth1:1 Link encap:Ethernet HWaddr 00:25:22:1c:6e:05
inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:10.42.0.1 P-t-P:10.42.0.2 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:1775 errors:0 dropped:0 overruns:0 frame:0
[code]...
my tablet can receive ip, can see ftp on server but can't see anything in my home network.
I have got the following Problem: I installed the 64 bit lxde Debian version... I couldnt configure the network during the installation because I just have a dsl modem and not a router... so the configuration of the network failed.... after the installation I started debian... and was surprised about the lack of "basic system configuration"-software that had been installed... I couldnt find aptitude or whats the debian-Update-Programm called .... instead I found OpenOffice... HAE? then I tried to configure internet access..... so I started a terminal and tried to start pppoeconf... but the program wasnt found! ARRRGG! What am I doing wrong here.... Why are these system utilities like pppoeconf not always installed...
View 1 Replies View RelatedI am working on a cross-platform application for Linux ,Apple and Windows, so I have a full tower system with four SATA hard drives that be selected with a switch, so that I can change drives and operating systems at will. -sort of makes me a jack of linux systems, but master of none.It's important to mention this, because it shows the strangeness of the problem as it is isolated to Debian* systems.
So where does debian/ubuntu get it's information to establish a network connection?How do I rectify the problem? I can hardly blame the hardware (RTL8111B), because the problem is isolated to Debian systems.
I just installed, and evolution doesn't seem to think it has internet. The icon with the power cord in the bottom left is unplugged, and send/receive is greyed out. Internet is working , but it is not using network manager, since network manager says no internet is connected. Maybe this has something to do with it?
View 1 Replies View RelatedI just installed debian, durning the installation i opted not to connect to the internet since the large network cable was in the closet and i did not feel like standing up. Now i have finished installing and plugged the network cable in, expecting it to "just work", this is not the case. What needs to happen before the wired network connection starts working? also, the lspci output, appearantly it won't find any network adapter. I suspect this is the fault of my lazyness.
[code]...
I'm using debian lenny.When I boot with kernel 2.6.36, ping always respond with Network is Unreachable. But when I boot with kernel 2.6.26 it works. I can't even ping the dafault router of 2.6.26 kernel when I am at 2.6.36. Also, system/administration/network does not show any connections while it shows something at the other kernel.
View 1 Replies View RelatedI've been dual booting Windows 7 and Debian on my desktop ever since. But recently I installed Debian again on a new laptop that I recently bought and unfortunately it's being very different from my first successful installation. The first problem is that Network Manager is not picking up internet on the new laptop. The Wireless tab is grayed out, so I can't click it and look for a new one. I've been using Wired internet since, but if I want to take it to work I have to have it be Wireless-able. Currently my Wireless Card is a Broadcom 4313 802.11 b/g/n which I'm fairly sure is supported. The second problem is installing Firefox. On my first installation it worked fine, and the bin file loaded and everything. However, for this second one that's been a completely different situation and the bin file hasn't worked (by this I mean I can't double click it to open it).
View 6 Replies View RelatedI would like to update my network setup.
Today, I have an ADSL box which is my gateway to internet (192.168.0.1).
I have a Raspberry pi (RPI) which I use as a dhcp & dns server (192.168.0.2).
Recently my mobile phone operator installed a 4G antenna beside my home, and the bandwidth and latency are much better with my mobile phone than with my internet provider (ADSL).
I would like to install a wifi dongle on my RPI (I would get wlan0 & eth0 interfaces)
When RPI detect my shared phone connection (tethering) I would like RPI to automatically route internet:
- from authorized devices on my network to my mobile connexion (wlan0 -> mobile phone).
- from other devices to the standard ADSL internet (eth0 -> ADSL box).
I don't want any device to use the shared 4G connexion, best would be authorized devices to be selected by MAC address. How I should properly setup such a network ?
I have installed debian to run Squid cache as a caching proxy.
Ive been bashing away now for 2 days and i have managed to install squid (i first tried manually, but that did not work so i used synaptic software packager to install it (from Administration menu)
That went well, thereafter i installed webamin to work with squid in a GUI
I have managed to start squid and added my range of IP addresses to the ACL list
I have added the proxy restriction too.
Now, i tried to test it.
I opened Iceweasel Web browser (on the same machine) and setit to use the Proxy server: localhost and port:3128
That works fine.
But when i try to change the proxy setting to my machines ip (where squid is installed) :
Proxy server: 10.0.0.35 and port:3128
That does not work.
Am i missing something, please help
I then tried to set another windows PC on the network to:
Proxy server: 10.0.0.35 and port:3128
That also does not work.
I also edited the conf file to http_access allow all, but i do not know if i have doen it correctly, but maybe there is another problem?
I have a server that is on both a standard network and a virtual network, as follows: server1 attached to standard network server1 acting as Dom0 with two linux DomU guests (under Xen) I only have one network card. How do I configure server1 to have a different hostname on the standard network than on the virtual network? Here are the relevant network configuration files for server1:
/etc/sysconfig/network-scripts/ifcfg-eth0:1
DEVICE=eth0:1
BOOTPROTO=none
NETMASK=255.255.255.0
IPADDR=192.168.122.9
[Code]...
today I tried to configure a network route to a host for testing my network interface. Code: route add 192.168.1.15 eth0 As I have to eth interfaces and both interface got their IP from DHCP (192.168.1.11 and 192.168.1.12) and are in the same subnet, I shut the other interface down:
Code: ifconfig eth1 down Then I tried to test the interface by doing a ping to 192.168.1.15.
Problem: When I unplug the cable from eth0 (and eth1 is still plugged) the ping still works. Somehow my linux (it's debian) powers up again eth0 and pings over this port.
How can I stop my linux doing this. I just want to have the route added only on the one interface - not the other. Is it maybe some case of a default-gateway?
I've installed the Ubuntu 10.04 Server onto a PPC G4 Mac just for the experience of setting up a server. During the installation process Ubuntu couldn't auto-configure my DHCP Network. I'm using the airport card on a wireless network. How can I manually configure the network once Ubuntu is installed.
View 6 Replies View RelatedIm new in this world of linux and suse. I have just installed the opensuse 11.2 in a Dell Inspiron 5160. Such laptop has a BCM4306 Wireless LAN controller. When I tried to configure a wlan connection, I found that the firmware was not installed. After looking in different forums, I installed the firmware b43. Now, my wlan card is abled to find the wireless of my router.
I have tried to configure a connection with YAST as well as with Network Manager, but both cases failled. Specifically, when I use Network manager, Im able to see in the applet my connection, how strong is the signal, but I see a yellow symbol (in one forum, such a box is shown with a green symbol).
I have check many time all about the secutity, encryption, and so one and all seems to be correct. But when I open the mozila firefox or the konqueror browser, no chance to surffer in internet. Now Im just a step to become crazy. The drivers are ok, the information about the router and the keys are ok, but in such a way, I am still harmloss.
I have just installed opensuse 11.3. I am absolutely new for Linux and for this forum. I have tried to open Network manager to configure my wlan. But its not starting. How to start network manager and configuring my wlan.
View 4 Replies View RelatedI'm going to come right out and say I am a complete novice with Linux/SUSE. The equipment I'm having a problem with is a little web-server that was purchased by my employer that has, quite suddenly, stopped functioning. I was changing the IP address within YaST, at which point the device offered to update itself, which I saw no harm in. Post-update, however, I was unable to so much as ping the device.
I tried "ifconfig eth0": "Error fetching interface information: Device not found." I went into network settings via YaST and found that there are two cards now listed as: RTL8111/8168B PCI Express Gigabit Ethernet controller Both IP addresses are "Not configured". The information pane, for both cards, cites:
RTL8111/8168B PCI Express Gigabit Ethernet controllerBusID : 0000:02:00.0 Unable to configure the network card because the kernel device (eth0, wlan0) is not present. This is mostly caused by missing firmware (for wlan devices). See dmesg output for details. The only difference in either of the cards is the BusID (0000:02:00.0 and 0000:03.00.0)
I can neither edit nor delete either of these cards. As I mentioned, I am a total Linux novice, and am at a total loss for what to do next, or even how to find critical information about the system itself. I know enough to check dmesg, but not enough to have any clue what to look for in the output.
OpenSuse 11.4 Asus Netbook 1000H Following other members in the forums I have installed Opensuse 11.4 on the Netbook. In the early days Ubuntu Netbook Remix worked well for me. But this has been discarded, and the "one size fits all" Ubuntu had become slow and cumbersome. So..... onto my post. Opensuse is working well. The install went beautifully.
It detected the Wireless Internet and I am able to get on line. I also need to share the Internet connection to a desktop. This is done via a small network switch. Thus far I cannot do this. I tried to use ifup to configure a static ip but this busted my Wireless configuration. I went back to knetwork manager. Then I tried to set up the wired network using knetwork manager and under IPV4 "share" the connection. But this blanks out any possiblity of a static address and substitutes dhcp. My desktop cannot ping the this dhcp address. Ubuntu had this thing called Firestarter? - from memory. This configured the system to sharing the network.
1 linksys router: gets the net from PPPOE and give the network DHCP. The router IP is 192.168.1.1. 1 windows laptop that work wireless and wired. 1 debian desktop that work wired and not working wireless. THe problem with the debian desktop is like this: I have a TP-Link TL-WN321G installed and found by lsusb command. I make a wireless connection WPA Personal (just like the router settings) it says i am connected to the wl network but no internet connection. the route command give me this:
[code]....
I tryed with wicd who said that the connection is WEP (and it's not, it is setup to WPA on the router and the network-manager conncetion) and when i try to connect i get bad password. I tryed with network-manager uninstalled and no chance.
I installed Suse 11.2 on clean HD. I cannot connect to the internet. Seems like Suse didn't install drivers for on board ethernet card. It is a Marvell Yukon 88E8056. I'm new to this and don't know how to install the drivers.
View 3 Replies View RelatedI have SUSE 11.0 set up to act as a router/firewall for my home network to the internet through a cable modem attached to an Ethernet card. When I was laid off several years back, I found information that let me connect my network to an ISP via a standard serial modem. I am considering going to the Sprint U1901 4G USB modem and dropping cable internet. Sprint claims the U1901 is Linux compatible. My thoughts are that using the 4G modem should be similar to the old dialup modem. I had a script that connected to the internet whenever internet traffic was detected. Unfortunately, I did not save notes on what I had done to setup the modem to dial automatically, and I have been unable to locate information that seems good to set this up again. I already know that all I had to do to get routing working was simply replace the internet port in the firewall/routing script with the port for the modem. So I assume that is rather trivial.
Would you please point me to a doc, perhaps SuSE specific, that gives reasonable directions on how to set up a "dial on demand" ISP connection? I assume that the 4G modem will be very similar to my old serial modem so that a dial on demand script will work. I did find a dial on demand howto, however, it did not seem to apply.
I am using ubuntu 8.10 ....
i am unable to configure my internet on it ..i have tried a lot of things, which i have are as follows...
1. i used these commands but unfortunately no result... sudo ifconfig eth0 192.168.1.21 $ sudo route add default gw 192.168.1.1$ sudo vi /etc/resolv.conf this file is edited to enter ipadd etc....
2.Setting the ipaddress in system>admininstrator>network config
there i edited the properties of "Auto eth0" for my ip address, mask, and default gateway....
P.S: My internet connection is perfectly working fine in windows xp. Details shown in windows are :
ip address : 192.168.1.21
mask :255.255.255.0
gateway :192.168.1.1
dns :59.179.243.70
In Damn Small Linux? I have a dinosaur computer I need to use for something, and there's no ethernet port. But there is USB. On the internet box my ISP provided there's a port for a usb cable. But I plug it in and there's no connection. Tried Vector too. Is there a terminal command to make it work?
View 9 Replies View RelatedI am new to Linux. Just installed Ubuntu 10.04 few days back. The problem I am having is not able to connect to internet. Mine is direct cable connection using CAT5 cable terminted to my ethernet card. and I connect to the net using a dial-up connection. I think other end of the cable is terminated to a common switch.I have tried searching it over net. The only thing I could figure out is that I have to do some configuration on pppoe (am i right?)Are there any commands I have to enter or anything like we used to do in windows?
View 8 Replies View Related