Where is now, in new Debian systems, the internal text file where the
adequate medium (live systems recognize a medium /dev/sdb1 if I connect my phone tablet)
has to be present if used?
Is a special procedure to be use to mount, open, read, close and unmount them properly?
at a particular spot on your screen on Debian Lenny xfce4 64 bit?
View 6 Replies View RelatedI have installed Debian Jessie (<-- brilliant OS ) on my uncles Laptop (it is a Thinkpad E540) with Cinnamon as desktop environment. The installation was no problem. Everything apart from one minor thing works nicely. The minor thing however is the following:
I don't know what it is, but when I don't use a particular usb port for a while and then try to plug in a usb stick or a wacom tablet, it doesn't get recognized, it doesn't show up when I use f.e. Code: Select alllsusb. When I close the lid of the laptop and open it again, then the particular usb device gets recognized and cinnamon asks me what to do, f.e. open a folder and show the content of the usb stick I have plugged in. Because of the success on two other laptops I use the following
Code: Select all# /etc/systemd/system/powertop.service
[Unit]
Description=Powertop tunings
[Service]
Type=oneshot
RemainAfterExit=no
ExecStart=/usr/sbin/powertop --auto-tune
Environment="TERM=xterm"
[Install]
WantedBy=multi-user.target
to save power on the Thinkpad (this is in no way my service script, I tuned everything using powertop in the terminal after having had logged in, the script above stems from a brilliant user here on the forum). Could it therefore be autosuspend that is not working properly here?
I scanned my newly installed Debian 8 and found that i have two ports open.
22 for ssh which i want
111 can i safely close port 111 and how?
So I have this laptop with a busted battery, I'm trying to get it into some kind of headless server, media topbox hybrid.
First thing I want to do is being able to leave it shut (powered on) in the corner without having to interact with it directly.
I've setup ssh and vnc so to login remotely and do task, transfer files and etc.
However there is a little issue with the laptop lid down upon turning it on, it immediately goes into suspend when getting to the display manager, which is 'lightdm'.
I suppose this is the default setting for Xorg and as such my custom configs for KDE only kick in after I login.
Question is: I never seen configuration for default power management stuff being done in Xorg, is there some way to disable automatic suspension on lid down?
Another question is: After the KDE kicks in does it always replace power options? I have setup a xorg.conf file specifying dpms options but these don't seem to remain.
I bought a hp envy x360, and I have installed debian 8.1 and I have some problems with GNOME.
I am running session and it works fine, but after some time it is closed suddenly and after I can't start session.
System is a Dell E7440, with Jessie, I recently upgraded to kernel 4.2.5 due to issues with wireless that are supposed to be fixed. (The same issue exists with jessie stock kernel 3.16 and BPO tough)
When I close the lid it often does not work and I get this in dmesg
Code: Select all[Â 567.104335] pci_bus 0000:01: Allocating resources
[Â 567.104349] pci_bus 0000:02: Allocating resources
[Â 567.104415] pci_bus 0000:03: Allocating resources
[Â 567.104428] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[Â 567.105515] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[Â 567.105540] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[Â 567.105585] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[Code] ....
I suppose the i915 stuff is something I can ignore, However
Code: Select all[Â 570.768020] acpi device:40: Cannot transition to power state D3hot for parent in (unknown)
seems to be the issue.. I don't even know what device:40 is.
in ls -l it shows as
Code: Select all lrwxrwxrwx 1 root root 0 Nov 2 12:28 device:40 -> ../../../devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/INT33C6:00/device:40
and
Code: Select all# cat /sys/bus/acpi/devices/device:40/path
\_SB_.PCI0.SDHC.WI01
The awkward thing is tough, software suspend by running "systemctl suspend" works perfectly and always.
Code: Select all [ 872.054627] PM: Syncing filesystems ... done.
[Â 872.091506] PM: Preparing system for sleep (mem)
[Â 872.092045] Freezing user space processes ... (elapsed 0.001 seconds) done.
[Â 872.093377] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[Â 872.094563] PM: Suspending system (mem)
[Â 872.094595] Suspending console(s) (use no_console_suspend to debug)
[Code] ....
So despite the mysterious issue with acpi device 40, how is real lid close different from "systemctl suspend"? And can I simply workaround the issue by making such a suspend when the lid closes?
I'm using xfce, and the power manager settings, to only lock the screen when close, are not honored. The laptop suspends, no matter what, when closed. Is there a way to forcibily only allow xfce power manager to handle the close lid behavior?
View 2 Replies View RelatedI don't know if these are related, but I have had occasional lockups, where no input has any effect and then it shuts down, and am usually unable to resume from suspend on closing the lid.
Here are the specifics. Thinkpad x120e, AMD e-350, ATI radion 6310 graphics, Intel 320 series SSD 80 GB, no bluetooth.
The ethernet and wireless cards, as given in lspci, are
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
04:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01)
[Code].....
I have made a bootable pen drive (2gb) and have a 30gb partition on my hard drive for unbuntu Im trying to try the OS by USB at the start into The BIOS If ya gets what i mean It successfully loads The Options menu where you pick a choice like run from usb So i run from usb and and it Loads Ubuntu just the purple background and the beans underneath it loading forever in the Logs this comes up
/init:line7:cant open /dev/sr0 :No medium
It will keep going like that anyone know whats wrong? Im using Windows 7 Build 7100* with a computer i built a year ago Intel e8400,6gb Ram, Asus P5Q SE Pro,and 100gb left on hard drive (30 Excluding cause i partitioned it =P) how do i remove the Floppy drive out of BIOS? i have it at the boot up priority at the last 1st is my hard drive then USB then CD Drive
I used t be able to install ubuntu, now I was able to install Fedador, but I get this message when I try to insatll ubutu can't open /dev/sr0: No medium found What do I do
View 1 Replies View RelatedI have some errors when run the mount -all command: mount: wrong fs type, bad option, bad superblock on /dev/sdc5, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Failed to open /proc/filesystems: No such file or directory
[Code]..
Debian 8.2 .... Desktop is lxde BTW. It auto-mounts the drive, and sometimes it's writeable for a while, but then it all goes read-only out of the blue. su doesn't work. I tried installing autofs and it doesn't mount at all.
/var/log/messages:
Nov 20 11:05:37 debian kernel: [589471.166033] scsi31 : usb-storage 1-3:1.0
Nov 20 11:05:37 debian mtp-probe: checking bus 1, device 41: "/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-3"
Nov 20 11:05:37 debian mtp-probe: bus: 1, device: 41 was not an MTP device
Nov 20 11:05:40 debian kernel: [589474.217399] scsi 31:0:0:0: Direct-Access PNY USB 2.0 FD 8192 PQ: 0 ANSI: 0 CCS
[Code] ....
syslog looks much the same.
I'm not an lxde fan. The file manager always was crashy. But I'm on an Acer Aspire, and too many desktop managers just can't deal with the screen ratio.
I was try to installed ubuntu 10.04 on the Macbook pro .But it was failed .I got following message:
/init: line 1: can't open /dev/sda: No medium found
I have already Bootcamp to create a partition to install Ubuntu . partition file system is FAT32.
When I plug in a usb flash drive, my Debian mount it, but when i am going to write, mkdir, rename file or paste a file permission denied.
The result of Code: Select alldev/sdc1 /media/usb0 auto rw,user,noauto 0 0
is Access denied
This is what writes when I enter localhost in browser and press Enter.
It works!
This is the default web page for this server.
The web server software is running but no content has been added, yet.
http://localhost/~david/baby.php
Not Found
The requested URL /~david/baby.php was not found on this server.
Apache/2.2.19 (Debian) Server at localhost Port 80
So , I copied file directly into /var/www folder, entered /localhost/baby.php and get this :
Server error The website encountered an error while retrieving http://localhost/baby.php. It may be down for maintenance or configured incorrectly. Here are some suggestions: Reload this webpage later. HTTP Error 500 (Internal Server Error): An unexpected condition was encountered while the server was attempting to fulfill the request.
So , it's not 'bout path or server .. or about php file (I tried few). I don't know what to do
I have a Western Digital 3TB USB drive connected to a Raspberry Pi 2 running Raspbian Jessie. I created an 30GB ext4 system partition and a NTFS Data partition using the remainder of the drive. I formatted the NTFS partition as follows:
sudo mkfs.ntfs -Q -L Data /dev/sda2
The drive works fine on the Pi but when I connect it to a Windows 7 pc the pc doesn't recognise the format of the Data partition and can't access it.
On the Pi I ran:
$ sudo fdisk -l /dev/sda2
Disk /dev/sda2: 2.7 TiB, 2968557453312 bytes, 724745472 sectors
Units: sectors of 1 * 4096 = 4096 bytes
Sector size (logical/physical): 4096 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
[Code] .....
Partition table entries are not in disk order.
I'm getting BSOD when I'm booting my main system (debian 8 fully updated). I get a BSOD with a _ sign. URL...because I can't access to failed boots files. Besides having the files
Code: Select allfelipe@debian ~ % ls /var/log/journal Â
362d07f9e18b45f8aec4575c347f181d 92e8a448f7a348719da129184a7e6821
Code: Select allfelipe@debian ~ % journalctl --list-boots
 0 0c51ae5b67f144059c5470dbe345d621 vie 2016-03-25 09:05:29 ART—vie 2016-03-25 09:11:58 ART
For my project, it's absolutely necessary to have a read-only root partition system. I have a writable /opt/project partition.But, I also need to start x server. startx This tries to write to some temporary files and fails as / is readonly. Is there any how-to on how to move this temporary files to the writable portions of the file system.
View 3 Replies View RelatedIs there a way to permanently, completely and utterly disabling the "feature" that stops me from opening my CD drive? I suspect it is the same thing that asks me if I want to play/mount/etc things when I plug them in. I don't - I just want to be allowed to use my computer without silly hindrances and interruptions. What is it that tries to take over my computer in this way?
View 10 Replies View RelatedI am trying to use thunderbird to connect to gmail. followed the instructions on the gmail help section to set up thunderbird and opened ports 995 for pop and 465 smtp on my router. When that did not work I posted on the thunderbird forum. It was decided there I had a problem with debian since both the thunderbird and router settings were right. doing more research I used nmap and netstat to check for open ports and it seems to me I only have tcp 80 and udp 138 open. downloaded firestarter hoping to solve the problem but in the events section it does not show thunderbird trying to connect to any port. Is this a case of not understanding what I am looking for here. Is there some way to open all ports on debian and then using firestarter to block the traffic I do not want.
View 11 Replies View RelatedI have just switched over from firestart to gufw.I have set all incoming traffic to deny and all outgoing traffic to allow.I have rules set for incoming traffic, and have only opened 1 port on my system for torrents. My router also only has the same port opened which again is for torrents.I use "Network Tools" which is included on squeeze and do a portscan of 192.168.1.100 and 127.0.0.1 I get all kinds of crazy ports coming back as opened. What is even stranger is if I do a few scans, these ports change, so one port on one scan may come up as open, then it will disappear and a different port may show as open.
Mind you none but the torrent port is forwarded in my router, I have no idea what any of these other ports are, or why they are even showing up.What the heck is going on? I dont think this is normal? Am I at any higher risk for attack?
I just set up a computer with debian (im no linux expert) and now i have trouble with getting the packages for my graphics card (its an RV635)
Im tried to do it like this page says: [URL]....
However when i try to Code: Select allapt-get update he throws an error:
W: Fehlschlag beim Holen von http://httpredir.debian.org/debian/dists/jessie/Release Erwarteter Eintrag »nonfree/binary-amd64/Packages« konnte in Release-Datei nicht gefunden werden (falscher Eintrag in sources.list oder missgebildete Datei)
I'm trying to get my Intel HM55 GMA HD graphics card to work in Debian Lenny.As the vanilla Xorg didn't have any support for it, I manually compiled the last stable Xorg source (1.7.1 - such a pain) and the Intel driver. But when I try to launch X, I get the following message :
(EE) GARTInit: Unable to open /dev/agpgart (No such file or directory)
(EE) intel(0) : /dev/agpgart is either not available, or no memory is available for allocation. Please enable agpgart.
I've just installed Debian Squeeze from a live CD. When I open a web browser (be it iceweasel or epiphany) and try to go to google.com, it tells me it can't resolve the host name. [Edit: They do, however, allow me to go anywhere on debian.org, minus the search feature] I also get the same error when I try to go to my website running on a local server. However, when I type the server's IP address (192.168.0.10), it goes to the website fine. Basically, any program I run that needs to resolve a host name returns an error, with the exception of the host command:
I've tried changing my DNS server IP from 192.168.0.1 (my router, configured to provide DNS) to 192.168.1.254 (my internet modem, also configured to provide DNS). That didn't help any. Then I changed my DNS server IP to the same one used by the modem, and now everything works.
I've tried googling my way out of the issue, and I've found where someone had the same issue as I've got and fixed it by adding "blacklist ipv6" to their /etc/modprobe.d/blacklist.conf file, but that didn't work for me.
So, recap: Why does resolving domain names fail for certain applications (except the "host" program) when the DNS server IP is that of my router or modem (which works fine for all of my other computers), but suddenly works when I point the computer straight to my ISP's DNS servers, and how can I permanently fix the problem?
I have a Broadcom BCM4312 LP-PHY in this machine. I was informed theres an open source driver for broadcom cards (brcm80211), but it doesn't seem to support this chipset. In the spirit of Debian, is there another driver available?
View 2 Replies View Relatedhow can i close all of ports and open ssh only?
View 6 Replies View RelatedI'm having some strange issues with my HP Probook. The resolution changes (lower) after I close and open the lid again. Only a restart will fix this problem. Sometimes happens even when I normally turn the computer on, only a restart will fix it...
View 7 Replies View RelatedI'm trying to install the openconnect VPN client on a server machine, Debian 7 Wheezy, and APT is trying to install a lot of dependencies. I think it's trying to install the whole desktop environment.I was searching the web but all articles are for desktop machines and nobody mentions my problem with the dependencies. I also have openconnect installed in two Gnome desktop machines without problems.
This is the output:
Code: Select all# apt-get install openconnect
Reading package lists... Done
Building dependency tree   Â
Reading state information... Done
[code]...
I have this one comp with an Radeon (MSI-R7850) card in it and its been working fine untill I tried to open Blender (3D creation Studio) today. Blender pops open and crashes. I opened it in command line to get the output but I dont know where to go from there. Blender used to work just fine on this comp. does on my others (they're NVidia).
output;
Code: Select all:~$ blender
X server found. dri2 connection failed!
connect failed: No such file or directory
X Error of failed request:Â BadLength (poly request too large or internal Xlib length error)
 Major opcode of failed request: 157 (GLX)
 Minor opcode of failed request: 1 (X_GLXRender)
 Serial number of failed request: 161
 Current serial number in output stream: 164
comp;
Code: Select all~$ uname -a
Linux node-1 3.16.0-4-amd64 #1 SMP Debian 3.16.7-ckt20-1+deb8u2 (2016-01-02) x86_64 GNU/Linux