I have been getting some compile errors here and there and have read that possibly I need to install the kernel-devel package.I am running 2.6.33.4 which I built from source.I have also built and installed the kernel-headers.I cannot find the kernel-devel for 2.6.33.4 anywhere, can I build it myself from the kernel source?
View 2 RepliesI'm attempting to install ndiswrapper-dkms package. The installation fails due to the following error:Module build for the currently running kernel was skipped since the kernel source for this kernel does not seem to be installed. dpkg reports that the source is installed
[code]....
I've been searching google for the past couple of days but haven't found anything specific. Any ideas to get me going in the right direction?
uname -a reports
Linux debtop 2.6.32-trunk-686 #1 SMP Sun Jan 10 06:32:16 UTC 2010 i686 GNU/Linux
I'm trying to use module-assistant to add the vboxdrv using instructions also found here in the debian forum. However, m-a can't find the linux-headers because it looks for the package linux-headers-2.6.32-5-trunk-686. I attempted to specify were the headers were by using:
m-a prepare --kernel-dir /usr/src/linux-headers-2.6.32-5-686/
but also doesn't work. Instead, I get the error:
Bad kernel version specification at /usr/bin/m-a line 566.
Anyone knows how to work around this?
By the way, the reason I am doing this is because when I installed virtualbox (following the instructions in debian wiki) there's no vboxdrv. When I try to modprobe it, I get:
FATAL: Module vboxdrv not found.
I'm attempting to install the driver for my atheros AR8131 PCI-E Gigabit Ethernet adapter (in my Lenovo laptop) on my newly installed RHEL5 system (it's not currently being recognized).
I tried using: 'make install' but hit an error "Makefile:61: *** Linux kernel source not found."
After this, I tried: 'sudo yum install kernel-devel kernel-headers'
To rectify this, but hit this error "No package kernel-devel available" (and the same for the headers). What should I do?
I've been trying to install nvidia drivers yesterday, so I went to runlevel 3, ran the .bin installer and it came up with error: missing kernel-devel and kernel-source.
So I go yum install kernel-devel, it does, but it doesnt find anything like kernel-source.
How do I fix this issue? I have Fedora 12, and I ran drivers from:[URL]..
I used Backtrack 5 and Fedora, basically I'm trying to install my wireless card but I don't have these installed to make && sudo. I burned the iso images for backtrack and fedora and booted my computer from them but can't figure out how to install kernel-devel on backtrack for example. I dled yum onto my flash drive but can't figure out how to install it.
View 14 Replies View RelatedI need help in understand how the kernel-header and kernel-devel works. Pretty new to Linux.
View 1 Replies View RelatedI have installed CentOS 5.4 & am trying to install VirtualBox on it. To install VirtualBox I run the command:
yum localinstall path/Virtualbox.rpm
It runs through the dependency check & says everything is fine. It installs the rpm & then says that compiling of the kernel module failed & that VirtualBox will not start until this is fixed, & that the most like cause is that the kernel sources are not installed.
I have installed the kernel-devel package & have the kernel source tree located at /usr/src/kernel/2.6....
I am trying to install the mysql workbench and it is looking for libzib-devel. I can not seem to find it in any yum repo. Does anyone know where I could find it?
View 2 Replies View RelatedI'm working on a Fedora 13 server trying to intal some soft following the same steps I did with some other server with Fedora 12 ( not 13, like the new one ).First problem that I found was with 'yum install kernel-devel'
Response: Nothing to do !
Then I tryed 'yum -v info kernel devel'
Response:
Installed Packages
Name : kernel-devel
Arch : x86_64
code....
Second problem that is stopping me is 'yum install gcc' Some dpendency problem that can not be solved. Tryed --skeep-broken but nothing is installed.I don't have gcc on my sistem.
I have a program that needs kernel headers. The machine is running CentOS release 5.4 (Final).
uname -r output: 2.6.18-164.9.1.el5
When I try to do a - yum install kernel-devel or kernel-headers I get:
kernel-headers i386 2.6.18-194.3.1.el5 updates 1.0 M
Why don't they match?
I recently installed debian squeeze 32bit on a second partition of my amd athlon 64 X2 dual core machine.Currently it is using linux-image-2.6.32-trunk-686 kernel.But linux-image-2.6.32-trunk-amd64 is available.on the repository.Is it a 64bit kernel or 32bit kernel optimized for amd64 architecture?
View 12 Replies View RelatedI am using DEBIAN 6.0 and I wannna update my kernel from 2.6.32 to 2.6.38. Every time, I do it but after the installation & rebooting into the new kernel it gives me error "UNABLE TO BOOT INTO THE KERNEL".
View 1 Replies View RelatedI have a problem with my custom kernel when I want to create the Nvidia kernel module.After this finished I installed the image and headers and created the Nvidia kernel module. Everything worked fine.However, if I remove the linux-source from my home directory then I can't create the kernel module.Even though I have the headers for the kernel installed.
View 2 Replies View RelatedUse 2.6.32.11-99.fc12.i686 kernel,
A package needs same kernel source to build.
Add/Remove Software show only: 2.6.32.12-115.fc12... & 2.6.31.5-127.fc12...
How to get kernel-devel-2.6.32.11-99.fc12.i686?
from what I understand kernel-devel does not bring in ALL the header files for install modules. so what i would like to know is how to install true headers instead of using kernel-devel. I found one tutorial, but it was way out of date.
View 3 Replies View RelatedI have a set of vm's with stable, testing, and sid to keep track of how things are going. When I did an apt-get dist-upgrade with squeeze last week, things seemed to OK (350 package updates) until the end. It didn't seem to like and / or was confused by a kernel dependency.
I am not too concerned yet. Because these are in vm's, I do a snapshot before any significant change. I can futz around with impunity because I have that backup.
I re-booted, and tried the apt-get dist-upgrade again with same results. I think I also tried apt-get -f install.
So I reverted to the snapshot, and will simply try again in the future. I recall that with lenny as testing, the font-desktop was really screwed up for about a period of 6 weeks.
However, just in case someone else runs into this:
1) a re-boot worked, but the failure of apt-get made me nervous enough to revert.
2) waiting for corrections has seemed to work in the past (with a single exception with a 4-disk SCSI software RAID10 update that failed to re-boot lenny successfully after what seemed to be a minor update -- that was on a real system, not a vm. I haven't gotten back to look at that.)
I tried installing the VBOX additions. But after running the VBoxLinuxAdditions.run file, building of the kernel modules failed. It gave following message: The headers of the currently running kernel were not found. If the current compilation fails then probably this could be the reason. The missing package can be probably installed with yum install kernel-devel-2.6.40.4-5.fc15.i686.
But when I tried installing the above kernel headers and devel package, it says no such package were found.kernel is 2.6.40.4-5.fc15.i686 but the kernel headers are not available for this version. They are available for previous versions i.e 2.6.40.3-0.fc15.i686.should I downgrade my kernel version (if it's possible) or is there any way things can work out. I have enabled 3D accelaration and given the memory of 128 MB for display. The memory for Virtual Box is 1 GB and hard Disk is 8 GB. The host system is windows 7.
I have a problem to install the VMware Server (VMware-server-2.0.2-203138.x86_64.rpm) on "Fedora 13 Desktop Edition 64-bit".I traied all tips I found, but nothing was OK.Please look my linux configuration and the error messages:
(VMware installation)
[root@localhost BKP]# rpm -Uvh VMware-server-2.0.2-203138.x86_64.rpm
Preparing... ########################################### [100%]
1:VMware-server ########################################### [100%]
The installation of VMware Server 2.0.2 for Linux completed successfully.Before running VMware Server for the first time, you need to configure it for your running kernel by invoking the following command: "/usr/bin/vmware-config.pl".
code....
is it save to install linux kernel 2.6.35.2 on Debian Lenny 5.0.5 or stick with automatic updates...
View 14 Replies View RelatedOn Lenny, due to some compatibility issues: kernels before 2.6.26 don't recognize part of my vaio laptop's hardware, while the last drivers of my videocard (version: 260, card: nvidia gt 230m) suffer some incompatibility problem (this is one of the most problematic computers I ever had), so I have to use version 256, which doesn't work with kernels after (perhaps) 2.6.32. So, I suppose I have to check each kernel between that two versions and hope that one of them will be ok. I searched quite deeply over the net but didn't find anything related to debian, except for generic kernels [URL], but as someone told me that it's better if I only install stuff from the stable repository or backports. What can I do? Is there any backports archive or something like that? Otherwise, what should I do?
View 5 Replies View RelatedI recently bought an AMD R7 360 videocard and I'd like to use the free Radeon driver.
Problem is, PCI-ID 0x665f is not present in Jessie's 3.16 kernel sources. The hardware however is supported, it's just not recognized. So I'll have to get the Debain sources and patch include/drm/drm_pciids.h
From the 4.1rc1 kernel I know what to patch and where.
Debian page that explains how to use the Debian build system for recompiling the current kernel from Debian packages?
Upgraded Wheezy to Jessie, by changing my apt sources to point at stable instead of wheezy. Ran upgrade, and dist-upgrade, all fine etc.
Then tried to update the kernel by installing linux-image-amd64 package .. seemed to work fine, but after a reboot my kernel version still says 3.10.23
What have I missed?
Code: Select allroot@hostname:~# apt-cache search linux-image
linux-headers-3.16.0-4-amd64 - Header files for Linux 3.16.0-4-amd64
linux-image-3.16.0-4-amd64 - Linux 3.16 for 64-bit PCs
linux-image-3.16.0-4-amd64-dbg - Debugging symbols for Linux 3.16.0-4-amd64
linux-image-amd64 - Linux for 64-bit PCs (meta-package)
[Code] .....
I have a MyBookLive where i installed a Debian 2.6 kernel. The system is running fine so far. Because of an error message when apt-get upgrade (udev) i tried to upgrade to 3.16. Here's what i did:
- apt-get install linux-image-xx
- apt-get install linux-source-xx
- extract the source
- copied the old .config from running 2.6 kernel over to the 3.16 directory
- make oldconfig
- make uImage
- make modules
- make modules_install
- copied uImage to /boot
No error messages because its a headless device - its just not booting up.
I was wondering if anyone can assist me. I am looking to build a server with Debian as the host. When I installed Debian (Squeeze) the default kernel was "2.6.32-3-trunk-amd64". When I tried to install 'Virtualbox' application, I got a failure because I didn't have the 'kernel-headers' installed on my machine. I noticed there are no specific header package the 'trunk' kernel I was using. I have a few questions so I guess I should begin:
Is it safe to remove the 'trunk' kernel and boot my system on just the regular 2.6.32-3-amd64 kernel? Is this OK or not recommended? Please explain whatever is the correct answer. This is my 1st time using a 'Trunk' kernel so I don't know the in's and out's of it.
If I am using Debian 'Testing' for virtualization via 'Vbox', is there a specific kernel I "should" be using?
I have maked a new kernel (version is 2.6.24.7) in debian system which kernel is 2.6.26, and then when i start the new kernel which is 2.6.24.7, it tells me that:
View 1 Replies View RelatedMy girlfriend got a 'new' (second hand) laptop, a HP Compaq 6715s. When I tried to install Debian on it, the install went immensely slow - glacial, even. It was a very minimal install but it tooks hours to get to nowhere.
I found out online that this was because of a problem between the current kernel and the hard drive (or HD bus, something hardware-y to do with the disk) which meant file operations were extremely slow. I thought "easy, patiently install Debian and then install newer kernel". Except that after six hours, the install wasn't even halfway.
So I install Arch Linux with the 2.6.35 kernel: no problems with the drive speed at all. After a lot of researching (I only played around with Arch once, more than a year ago) I got the system into a usable state. But now wlan0 has suddenly disappeared, together with some other problems - and a usable laptop wasn't exactly what I had in mind, it was supposed to be awesome (or at least good). Which, with Debian, it would be
So... is it possible to make a Debian installation use a later version of a kernel? I'd want to install Debian with the 2.6.35 kernel, not install Debian and then afterwards update the kernel (because I don't have 24 hours to install an OS, if it'll ever even install).
I've found some stuff online but it might well have been written in the Cyrillic alphabet. All I understand, I think, is that in theory it's possible.
I installed Debian Squeeze from a net install to a raid 1 array. I have been having a lot of troubles related to being able to write to one or more of the mounted drives - even touch gives me errors.
The most interesting line from dmesg is:
Here is the full output from dmesg:
I found a thread that indicated that this bug was fixed in the next kernel version: 2.6.32-6. I am willing to upgrade the kernel to get rid of my problems. Is a squeeze kernel at 2.6.32-6 or higher available? If so, where? I have not compiled my own kernel, and am not very interested in getting into that.
Trying to compile the 2.6.36.2 kernel. Its not the first kernel I've compiled, but I've run into a problem I've not come accross before.
While compiling I get this error.
[Code]....
Looks like the headers sys/eventfd.h and linux/virtio_rng.h haven't been selected in my .config file. I just copied my old config from the last kernel I built. This was a while ago (2.6.30), but I thought I'd give it a go anyway.
what config option they are under or what I can do to get rid of this error?
This is Wheezy x86_64. I tried two different ways to install kernel 2.6.38 on my machine and both have failed. First thing I did was to follow this guide [URL]... el-26.html) and try to compile the latest stable from kernel.org. I don't know why, but it turns into kernel panic when I try to run it. Second thing I did was to install the liquorix 2.6.38, and that also fails, seeming to boot but hanging a second short from the login. I don't know what I'm doing wrong. Is there a special way to install kernels in Debian? This is the first time I tried compiling a kernel, so it's quite likely that the problem is sitting 6 inches from the computer screen. Also, how would I remove those kernels since they're obviously not working? I know I could remove them from the grub menu but I'm not sure how to completely delete them.
View 12 Replies View Related