Debian Configuration :: Prevent Driver To Do Update
Nov 18, 2010
I have a PC that have a new Ethernet card that is not yet supported by Debian/Lenny.I downloaded the latests driver from the manufacturer and after a make;make install everything works like a charm.My problem is that one day after a probable update, Debian overrided my new driver by an other one causing my Ethernet card to shut down.After an other make install, everything work again like it should..But how do i do to prevent Debian to update my driver ?
View 1 Replies
ADVERTISEMENT
Jan 4, 2016
Yesterday I installed some updates on my Jessie system (I don't remember if the kernel was also updated). After rebooting the system nothing happens after the "Loading intial ramdisk"-message. If I boot in recovery mode the boot stops at the message:
Code: Select allfb: switching to nouveaufb from simple
If I add "nouveau.modeset=0" temporary to the GRUB-entry for the recovery mode, it will boot up in the console-mode.
I was able to get an ethernet connection with "dhclient eth0" and removed the "xserver-xorg-video-nouveau" package. Then I installed it and the removed gnome-desktop again. Before removing it, aptitude said the following to the package:
Code: Select alli A xserver-xorg-video-nouveau
Now it only says:
Code: Select alli xserver-xorg-video-nouveau
But this didn't change my problem. I found a similar case in the internet, but there were no solutions for it: [URL] ....
The next thing I would do, is to install the proprietary nvidia-drivers, but since I have a GTX 960 video card, I would have to use experimental drivers. So I'm afraid to make it more worse trying to install this drivers.
Also I'm not sure if it really is a driver-specific of kernel-specific problem. My kernel is version 3.16.0-4-amd64.
View 10 Replies
View Related
Jun 11, 2010
I have the latest version of Debian installed on a Poweredge 1600SC. Everything is working ok, but the Adaptec AAR 2410sa PCI SATA card has started being a bit weird. I have a 1TB drive connected to it and noticed that occasionally it was unmounting the drive and messages appeared in the /var/log/messages like the following:
Jun 10 23:50:57 servertron kernel: [11246.006500] sd 1:0:2:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
Jun 10 23:50:57 servertron kernel: [11246.006500] sd 1:0:2:0: [sdd] Sense Key : Hardware Error [current]
Jun 10 23:50:57 servertron kernel: [11246.006500] sd 1:0:2:0: [sdd] Add. Sense: Internal target failure
After a reboot everything would be fine. I did some research and heard that it could be the drive failing, so after running a disk check etc I connected up a new 1TB drive (was getting low anyway) to another SATA interface on the card and started trying to copy from one drive to another. Lo and behold, it happened on the new drive as well. Bugger.
I haven't had time to open it up and check the connections and will be doing this shortly, but thought I would check to see if it was using the best/newest driver, but am a bit stuck as to where to start. I've looked through some docs and help but can't really see how to update and check hardware drivers in debian.
lspci shows the following:
00:00.0 Host bridge: Broadcom GCNB-LE Host Bridge (rev 01)
00:00.1 Host bridge: Broadcom GCNB-LE Host Bridge
00:02.0 Ethernet controller: Intel Corporation 82540EM Gigabit Ethernet Controller (rev 02)
[code]....
Is there a newer version of accraid I can use? Even if there isn't, how would I go about identifying which driver the card is using and installing an update?
View 1 Replies
View Related
May 28, 2010
Alright, first Squeeze wouldn't create an initial RAM disk even with "--initrd" specified. Now I don't need one and it's creating one for me even though I don't want one! How do I stop this? I'm beginning to feel like I am using Windows in the sense that it's doing things on its own. Don't make me a RAM disk unless I say so!
View 10 Replies
View Related
Jul 24, 2010
i would like to prevent all users other than the user "parker" on my system from using the su or sudo commands. I have not attempted to modify the sudoers file so it just contains the standard root ALL = (ALL) ALL.
View 5 Replies
View Related
Feb 8, 2011
Howto create usb-hdd using live-helper to prevent xfce desktop from any changes? Normal user shouldn't change any icon on the desktop.
View 8 Replies
View Related
Jan 7, 2011
We have the following server at collocation: [URL]
Provider's technicians were working for 3 hrs but finally were unable to set up hardware RAID1 on it.
What could prevent them from doing it? Is it difficult to set up RAID1? It is mentionned as basic function in specifications.
They said debian not booting after raid configured...
View 2 Replies
View Related
Dec 16, 2010
A few days ago I had a problem with my screen resolution after a safe-upgrade. I struggled a little but I finally downgraded and pinned the intel driver. But now, each time I turn my computer on I get a notification of "1 update aviable" I've checked and the update is correctly pinned (I used keep and forbid-version), it does not upgrade. As you can see, this is not critical, but I would apreciate a fix.
Details:
Debian sqeeze/sid with KDE4 on Acer Aspire One ZG5. I manage my programs with aptitude.
View 3 Replies
View Related
Apr 1, 2016
I'm trying to prevent GDM/Gnome from turning the screen off prior to login. It's current behavior, under 3.14, slowly fades the screen out and then enters DPMS mode after 10 minutes.I have zeroed out the following dconf settings, under both root and user, but the default behavior persists.
org.gnome.desktop.session idle-delay
org.gnome.settings-daemon.plugins.power sleep-inactive-ac-timeout
org.gnome.settings-daemon.plugins.power sleep-inactive-battery-timeout
View 0 Replies
View Related
Jul 27, 2011
I have a ppp0 entry with post-up options like this
mapping ppp0
map none photon-plus motorola
map timeout: 12
## map init-time: 12 # for slow drivers
[code]...
If I comment those off then no such problem, hence some how ppp0 executed automatically and there is no [auto ppp0] any where. How can I stop this forcefully ?
View 2 Replies
View Related
Feb 15, 2010
Just installed squeeze on a new laptop(had been runny Lenny on my older one with no issues, but no sound or wireless on the new one).I decided to install the ATI drive for my Radeon Mobility 4500(or some close revision) because the fan is constantly running and based on some other postings, it seems that it could be the graphics card causing it.Downloaded the driver from ATI's site and it seemed to install fine but when starting X.
View 11 Replies
View Related
Sep 4, 2015
i've installed debian 8 on this laptop but can't use the nvidia card from nvidia-detect can't find the card but it work 'cause i can see it in the list of hardware, 3d controller the driver from nvidia don't work, and i had a problem with force installation and xorg.conf file.. how i can make it work ? the card it's nvidia 820m
View 3 Replies
View Related
Sep 21, 2015
I have PCI-device and driver for it - tmk1553b.ko
The problem is to make this device work i have to open terminal after system starts and write
Code: Select allcd /path/to/driver
sudo insmod ./tmk1553b.ko d0=1 t0="TAI" misc=1
But idea is that this PC will work without operator so driver must be loaded automatically. As i realized the solution is to make script but when i try google it shows me how and where to put this script but not how to make it. Also i've tried to put tmk1553b.ko to /lib/modules/2.6.32-5-686/kernel/drivers/misc but it doesn't work.
Debian 6.0.10 (squeeze)
Kernel 2.6.32-5-686
View 5 Replies
View Related
Jun 7, 2010
I recently installed Squeeze. I had sound with the video driver that came with the install. Then I installed the Nvidia driver from Nvidia website. The sound dissappeared. When I uninstalled the Nvidia driver and removed xorg.conf and rebooted again, the sound came back. Then I installed the Nvidia driver from (nvidia-glx, dev and settings) from Debian with Synaptic. The sound went away again. If I uninstall the nvidia driver and xorg.conf the sound will probably come back again. The sound driver is the one that came with the install.
The volumes are unmuted in the alsamixer. Somehow alsaconf command does not work.
My mother board is a ASUS M4N78 Pro with Nvidia IGP.
What can I do to have sound with the nvidia driver?
View 14 Replies
View Related
Jun 21, 2011
I've got a Dell Optiplex Desktop here, the CPU is a Intel(R) Core(TM) i5-2400 CPU @ 3.10GHz. The integrated ethernet here is from intel also, it's a 82579LM Gigabit Network Connection. This computer is running a Debian Squeeze 64bits, distrib sid, kernel 2.6.39-2-amd64.Well, here goes the story. I had a lot of trouble with the ethernet card, being very slow, and it just didn't work when i was using tftp. So I downloaded and compiled the latest driver available on Intel website. Currently with debian sid, the version for the driver ( e1000e ) is version: 1.3.10-k2. From Intel I got the version 1.3.17-NAPI.Alright, so I build it, and move the module manually to the right place, replacing the previous version at the same time ie :
$ sudo cp e1000e.ko /lib/modules/2.6.39-2-amd64/kernel/drivers/net/e1000e/e1000e.ko
However, there is is still something bothering me. When I want to check, after rebooting, that I did it right, here is what happens :
$ sudo ethtool -i eth1
driver: e1000e
version: 1.3.10-k2
[code]...
So, which one should I trust ? Is there something I didn't do properly when installing the module ? Or maybe I just don't understand ethtool and modinfo enough.
View 5 Replies
View Related
Jan 15, 2016
I just installed Debian 8 and it doesnt look like my WiFi card is working. Unfortunately I didn't make a note what is the card manufacturer. How would I update WiFi driver?I previously had Windows 7 but I installed Debian over Windows.
View 2 Replies
View Related
Oct 6, 2015
Today I fresh installed the latest stable version of debian (jessie) with gnome from the USB DVD image for a 64bit machine. Everything got fine except the graphic driver, I think.
Now Gnome 3 is running but graphic is super slow. My previous debian/gnome 3 ran much better and I think there is a problem with the graphic driver.
I'm on an thinkpad t61.
Processor: Intel Core2 Duo CPU T7500 @ 2.20GHz × 2
Ram: 4GB
Graphic: VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (primary) (rev 0c)
Now the graphic is: Gallium 0.4 on llvmpipe (LLVM 3.5, 128 bits) which is likely wrong. If I'm not mistaken llvmpipe is pure slow software acceleration.
Moreover this was different on my previous debian (wheezy), which was faster. Anyway I don't know what " Gallium 0.4 on llvmpipe (LLVM 3.5, 128 bits) " is and it was for sure different in wheezy.
According to apt-get I have the latest intel graphic divers installed. So maybe this an X-org confic problem?
View 5 Replies
View Related
Oct 22, 2015
I am running fully updated Stretch. I am tring to complie a driver for Ralink 5370 USB WiFi dongle. When I do make I get the following error:
Code: Select allmake[1]: Entering directory '/lib/modules/4.2.0-1-686-pae/build'
make[1]: *** No rule to make target 'modules'. Stop.
make[1]: Leaving directory '/lib/modules/4.2.0-1-686-pae/build'
Makefile:356: recipe for target 'LINUX' failed
I have installed build-essentials, linux-headers and linux sources. What I have to install to complete this compile?
View 3 Replies
View Related
Apr 2, 2010
I follow a french tutorial to install the nvidia pilots. So, i did :
$ su
# apt-get install module-assistant
# m-a prepare
# m-a clean nvidia-kernel
# m-a a-i -i nvidia-kernel-source
[Code]....
View 6 Replies
View Related
Apr 21, 2010
I was able to successfully put together the driver with the Linksys WUSB100 v2 using ndiswrapper.
Here is what i get from ndiswrapper -l: rt2870: driver installed device (1737:0078) present (alternate driver: rt2870sta)But, the catch is where it maps to: ra0 instead of wlan0. This has caused me problems in order to get it to connect through network-manager or in the terminal.
ifconfig output for ra0:
ra0:
Link encap: Ethernet HWaddr 00:1e:e5:e8:14:e6
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[Code]....
View 4 Replies
View Related
Apr 22, 2010
I'm trying to install the driver for mi wireless card. The instructions say that to build the tar.gz file, I have to:
# mkdir hybrid_wl
# cd hybrid_wl
# tar <path>/hybrid-portsrc.tarhybrid-portsrc-x86_64.tar.gz
The third step i don't understand. I want the folder of the driver to be located in a folder inside home called "Programas" so what I did was to open the terminal, went su, and then did cd Programas. Then I followed instructions 1 and 2, but I don't know what to put where it says <path>.
View 14 Replies
View Related
Jul 18, 2010
I just installed Debian 5 in my pc. I have made all the updates but my screen is a bit bright and the resolution isn't very good. I think that i need to install the graphic card driver but all the solution i find in google didn't work . My laptop is Toshiba satellite pro u400 and my card is Intel GMA 4500 MHD.
View 4 Replies
View Related
Feb 23, 2011
I'm attempting to get a Realtek 0bda:8176 wireless usb adapter (lsusb gives: Bus 001 Device 006: ID 0bda:8176 Realtek Semiconductor Corp.) running with my Debian Server, I researched and found that the RTL8192CE driver is required for my adapter but when I run make install I get this error:
[Code]....
View 2 Replies
View Related
May 10, 2011
I'm encountering a problem running X and Gnome from a Xen-enabled Kernel with NVIDIA Binary driver compiled with IGNORE_XEN_PRESENCE=y on debian squeeze
Hardware:
NVIDIA NVS 5100M
Kernel:
Debian Squeeze : 2.6.32-5-xen-amd64
NVIDIA Kernel from the official package
Boot and module loading are successful, but when X starts, I only get a black screen. I attached here my Xorg.0.log, however it doesn't seems to have any problem.
View 5 Replies
View Related
Jul 14, 2011
I get plymouth and install it success, but it only support nouveau(nvidia) mode.
When I update my driver with [URL] , plymouth gone.
Is there any other way to do boot-image with the driver from [URL] ?
I find super-image-manager(buc), but I can not install it.
Addition: What is buc ?
View 3 Replies
View Related
Feb 24, 2010
Apparently, the wireless adapter Realtek 8171 uses the rtl8192se driver, which is currently available only as source from Realtek's website. Is building a driver equal to building a package? Should I follow the same cautions, say these ones?
View 9 Replies
View Related
Jun 26, 2010
Is there a way to programmatically determine whether a particular driver support is built-in rather than a loadable module? I'd be grateful if somebody would share how. I have written a shell script using the RTC (real time clock). I can check whether the rtc-cmos kernel module exists and load the module accordingly as needed, but I don't know how to determine when the driver is built-in. Of course, if the driver is built-in then the module does not exist.
I seem to recall there is a method to query the kernel config file (/proc/config.gz), through which I probably could grep for the CONFIG_RTC_DRV_CMOS parameter. I also can check whether /proc/driver/rtc exists. If that file exists then either the driver is built-in or the module was loaded.I realize the rtc-cmos driver is built-in with the standard Debian kernel build, but I still would like a way to query where the driver is supported.Is there a straightforward or direct method to query the kernel whether a particular driver is built-in?
View 3 Replies
View Related
Mar 2, 2011
I have a printer connected locally to my Debian box. It runs fine via cupsd.I am also running a Windows 2003 VMware guest which I would like to use the printer (use as a local printer, not a network printer).
VMware offers a connection via USB, so it should work. The printer I have plugged locally into the Debian host is recognised by the Windows 2003 guest, but it won't print. I get an error message saying that the printer is still connected to the host OS, and that I need to remove (or presumably disable) the host driver before the guest can use the printer.
So how can I find out which printer driver/module is being used by the Debian host to connect to this printer? And what is the best way to temporarily disable it, while my VMware guest is running?
View 3 Replies
View Related
Mar 4, 2011
Alright, Lenny has a working "fglrx-driver" package for my laptop, but Squeeze does not. Would it be possible to install the one from Lenny on Squeeze since Squeeze has newer libraries and such? I know I can't install new stuff with older libraries, but can I install the old stuff with newer libraries? I am at the end of my rope here! I mean ATI sucks and we all know this, but I've always found a Linux/open-source alternative that worked, until Squeeze.
View 10 Replies
View Related
May 14, 2011
I've been following this guide for squeeze: [URL] After getting the wireless-tools and firmware-ralink packages installed with no internet, I managed to installthe driver using modprobe rt2870sta (the 4th step). With the module loaded and the device plugged in (a RangePlusWireless Network USB Adapter with the WUSB100v2 chipset), iwconfig returned something like
[code]....
and then ifconfig wlan0 up returned ERROR while getting interface flags: no available device
View 14 Replies
View Related
