CentOS 5 Networking :: Error - No Network Devices Available - 5.3
May 6, 2009Right now I have this error
On my top right hand corner. No network devices available.
My distro is Centos 5.3
ADVERTISEMENT
CentOS 5 Networking :: After Install Cant Surf The Net - No Devices For Network
Sep 12, 2010I installl centos in my pc after i install, i cant surf the net,showing no devices for network
View 1 Replies View RelatedCentOS 5 Hardware :: An Error Occurred - No Valid Devices Were Found
Jul 12, 2010when i want to install centos 5.5 i take this error:
An error occurred - no valid devices werefound on which to crate new file systems.
my hardware specification is:
motherboard: gigabyte p55a-ud3
ram: ddr3 crucial 4gb
cpu: corei5 750
hdd: 2X1TB wd black edition raid1
CentOS 5 Networking :: When Type Command To Edit My Network IP Address Get Error
Dec 9, 2009I installed Centos server and when I type this command to edit my network IP address I get this error.
View 5 Replies View RelatedUbuntu Networking :: No Network Devices Available?
Nov 17, 2010I'm looking for some help on how to troubleshoot the network on Ubuntu 10.04 64 Desktop. It's on a Acer Aspire 721. There's a wireless card but the widget in the top right says there is no network device.
View 2 Replies View RelatedUbuntu Networking :: No Network Devices Available 10.04.2
Jun 6, 2011Just built a box and once 10.04.2 64 bit was all installed and loaded up I realized instead of showing my Ethernet as connected it had the ol x. So when I clicked on it I got "No network devices available." The mainboard is an Asrock 890GX Pro3, link light completely out.
View 1 Replies View RelatedNetworking :: Fedora 15 Naming Network Devices
Jun 23, 2011I'm doing a few tests with fedora 15. I'm surprised because they changed the naming way on network devices. eth0 is now called em1.At every fedora I have found the configuration files in /etc/sysconfig/network-scripts, but today I can't find them.
View 1 Replies View RelatedUbuntu Networking :: Boot Computer And Network Manager Shos "no Network Devices Available"?
May 10, 2010Loaded Ubuntu 10.4lucid on TransPort NX Mobile Pentium II, 328MiB,Using Netgear Rangemax wn511b. with Broadcom STA wirless driver. bcm43gx.Boot computer and network manager shos "no network devices available" Run system/administration/hardware drivers and the Broadcom STA driver shows up (only one that shows up) REMOVE and then ACTIVATE and the network manager sees it and connects fine. Shut down computer, restart and no device. I am forced to Remove and Activate each time I start the computer.Is there a way to set this driver to be found and run at computer start.
View 4 Replies View RelatedCentOS 5 Networking :: Devices Can't Be Found When Boot
Nov 6, 2010I`ve boot my laptop by centos. then my devices cant be found.
View 1 Replies View RelatedFedora Networking :: App That Continually Checks For Devices On Network
Dec 4, 2010Does anyone know of an application that continually scans for devices on a network and notifies you if a device connects/disconnects to/from the network? I just want a way of knowing when a computer is connected and when it's not.
View 10 Replies View RelatedUbuntu Networking :: Multiple Devices On Single Network
Jan 14, 2010I've got a co-worker who is trying to connect multiple devices to his wireless router - Xbox, Wii, TV, Dishnetwork box, etc. Not all of the devices are wireless however. He's had several thoughts on how to get this done and I know very little about this kind of thing so I thought I'd ask some of you.
His first thought was to buy a multi port bridge, but he doesn't like any of the ones he's seen so far.The other thought was to connect all of the devices to a switch and then use a single bridge, but he isn't sure if this would work.
Ubuntu Networking :: HP Mini 1116nr 'No Network Devices Available'
Aug 12, 2010I'm running Ubuntu 10.04 on a HP Mini 1116nr as expected i have no Wireless access but i also seem to have no wired access either.
View 2 Replies View RelatedNetworking :: Identifying Network Devices At Boot Time?
Dec 23, 2008I boot linux off a USB stick on many different computers with different hardware. How can I determine in a script which devices eth0, eth1, wlan0 exist and which hardware devices they apply too? Sometimes a wireless card is wlan0, other times it is eth1 or even eth3! The proc/net/dev file does not inidicate which hardware is installed.
View 2 Replies View RelatedNetworking :: Two Network Devices For Increased Transfer Rate?
Jan 28, 2011I have not tried this, and I am only wondering about the result.Let's say that I have a PC/Laptop with two network devices: an ethernet and a wireless. Can I connect both of the to the same network (if this network allows both connection) to increase the transfer rate between the PC/Laptop and the server???
View 5 Replies View RelatedUbuntu :: Mapping Network Devices Like Windows Networking?
Jan 9, 2010I am running Ubuntu 9.10 and Windows 7 (Wubi). Windows Networking shows all devices on the network (computers, routers, etc). Is there a way to get Ubuntu to do this (Would prefer GUI)?
View 3 Replies View RelatedUbuntu Networking :: Server Doesn't Find My Other Network Devices
Jun 30, 2010I've got three network devices on a laptop:
1. Built-in ethernet LAN
2. Built-in ethernet WLAN
3. PCMCIA ethernet LAN
I installed Ubuntu Server on this computer without the last one inserted.I inserted the last one today, and it lights up when i put in the cable. To be sure if Ubuntu has found it, I tested with the install CD and could see that it found all three at the first part of the installation where I have to chose a primary device.I can't get my WLAN card working, neither do I get my PCMCIA LAN card working. The third card, this PCMCIA card, has worked on Ubuntu Desktop using another laptop. And as said, the setup finds all three.
Ubuntu Networking :: Network Manager No Longer Seeing Devices After Reboot
Dec 5, 2010I just loaded 10.10 on an Acer Aspire One D255. When I installed Ubuntu, network manager loaded and I was able to use both the wired and wireless cards. After I used update manager, the kernel was upgraded, and I also added some wireless applications (RutilT WLAN Manager, SWScanner, and WiFi Radar). Upon reboot, the network manager doesn't work, and it cannot find any of the devices.
View 9 Replies View RelatedUbuntu Networking :: Enabling Wifi In Laptop For Other Devices When Connected To Wired Network
Jul 14, 2010This may be more suited for the networking forums, but I figured Community Cafe would be well rounded enough for someone to tell me if this is even possible (with minimal configuration that is).There are a few places I travel where I only have a wired connection to the Internet (no wifi), but when this happens is there a simple way to create an adhoc network so wireless devices can route through my computer and to the network? Reason I'm asking is I'm thinking of getting an iPad or iPod Touch which have wireless connections, but in the cases where my laptop is using a wired ethernet connection and the wireless card isn't used, I'd like to create an adhoc wireless network that'll let such wireless devices work.
View 4 Replies View RelatedFedora Networking :: FC10 - Wifi Devices To Work On 128bit WEP Network - Linksys Wireless-G And 5100AGN
Jun 20, 2009I'm having trouble getting my wifi devices to work on my 128bit WEP network. I have a new Thinkpad T400, with an internal Intel PRO/Wireless 5100 AGN. I also have some cardbus cards: a Lucent ORiNOCO Gold, a Linksys Wireless-G, and a TRENDnet TEW-421PC. I have them set up as interfaces eth2, eth1, and eth3. (The TRENDnet isn't recognised as a network card at all, so no interface for it.) I have installed the latest firmware for the Linksys card.
The /etc/sysconfig/network-scripts/ifcfg-* files are virtually identical for all of them, differing only in the HWADDR and DEVICE lines. So here's the behaviour:
1. The Lucent card comes up just fine.
2. The internal 5100AGN and the Linksys cards won't come up, and watching with iwconfig shows that they're either associated with my AP OR they've got an encryption key set -- but not both.
3. When trying to bring up the 5100AGN, I get the following messages:
iwlagn: index 0 not used in uCode key table
iwlagn: index 3 not used in uCode key table
/var/log/messages shows DHCPDISCOVER requests being sent, but they're bound to fail since the association with the AP with WEP isn't being completed. And yes, the ifcfg-* files really *are* identical except for the DEVICE and HWADDR lines. The /etc/udev/rules.d/70-persistent-net.rules file correctly maps the interfaces to the MAC addresses. So why does my antique ORiNOCO card work and thew newer ones fail? How can I track down what's being done wrong/not being done?
CentOS 5 Hardware :: SW RAID - Raid Devices Larger Than Total Devices
Dec 7, 2010I'm working on a server and noticed that the to RAID5 setup is showing 4 Raid devices but only 3 Total devices. It's on a fully updated CentOS 5 system that only has three SATA drives, as it can not hold anymore. I've done some researching but am unable to remove the fourth device, which is listed as removed. The full output of `mdadm -D /dev/md2` can be see below. I've never run into this situation before.Anyone have any pointers on how I can reduced the Raid Devices from 4 to 3? I have tried
mdadm /dev/md2 -r failed
mdadm /dev/md2 -r detached
but neither work and since there is no block device listed I'm not quite sure how to get things back in sync so it's only seeing the three drives.
/dev/md2:
Version : 0.90
Creation Time : Tue May 25 11:07:04 2010
Raid Level : raid5
[code]....
Ubuntu Networking :: Can See All Devices On Local Network And Their Local Ip Addresses
May 16, 2010I'd like a way to see all of the devices on my local network and what their local IP address is. I recall that I used wireshark to troubleshoot a similar problem a while back, but it doesn't seem to have a way to see all of the devices- only the traffic. (I'd like to do this without having to physically interface with my router if possible, and I am in an encrypted network if that matters)
View 6 Replies View RelatedOpenSUSE Network :: Can't See Any Of Devices Showing Up In Network Manager
Feb 2, 2010I can't see any of my devices showing up in network manager to configure even though they're using dhcp and working. How do I get them in so I can configure a proxy?
View 3 Replies View RelatedOpenSUSE Network :: No Network Devices Recognized On New Install
Feb 24, 2011Just installed 11.3 kde. When running the live cd both wireless and ethernet devices appeared in the network connections manager utility. I even connected to a wireless AP.I just booted up for the first time and none of these devices are available. There is no network manager icon in the system tray, and when the network manager utility is maually opened the only connection type i can select is vpn.I know that opensuse should be able to recognize these devices since they were available and working via the live cd, so can anyone help me restore them?
One extra piece of info, is that I am sharing a home directory with a gnome ubuntu install. there were a few minor issues i dealt with initially, but i didnt need to change this user's UID like I have had to do in the past so that's good. Each time i open a terminal I get two pieces of output assuming from the bash startup saying something like.URL...I highly doubt that these problems are related, but figured I'd post. Also if someone knows the solution to that as well, that would save me a bit of googling.
CentOS 5 :: Does The Centos Kernel Support Growing Raid Devices
Oct 16, 2010I'm setting up a raid 5 on several hard disks with a layer of lvm on top for good measure.I know the recent kernels support growing software raid, but since centos runs 2.6.18, I wanted to make sure it'll work. Does the centos kernel support growing raid devices?
View 1 Replies View RelatedCentOS 5 Networking :: Configure Server1 To Have A Different Hostname On The Standard Network Than On The Virtual Network?
Oct 5, 2010I have a server that is on both a standard network and a virtual network, as follows: server1 attached to standard network server1 acting as Dom0 with two linux DomU guests (under Xen) I only have one network card. How do I configure server1 to have a different hostname on the standard network than on the virtual network? Here are the relevant network configuration files for server1:
/etc/sysconfig/network-scripts/ifcfg-eth0:1
DEVICE=eth0:1
BOOTPROTO=none
NETMASK=255.255.255.0
IPADDR=192.168.122.9
[Code]...
CentOS 5 Networking :: Setup A Network To Network VPN Tunnel Between Our Main Office And A Temporary Location?
Aug 12, 2009I am attempting to setup a network to network VPN tunnel between our main office and a temporary location. This location need full VPN access back to the main office's network.Anyhow we have spent about 3 solid days attempting to make this work without any great success. Here is our network scheme for these two devices.
Network A (Main Office) (OpenBSD using isakmpd)
Network: 172.16.8.0/24
External IP: 1.1.1.1 (obviously not the real IP)[code].....
CentOS 5 Networking :: CentOS 5.3 And Atheros AR928x - Wireless Network?
May 12, 2009I have installed CentOS 5.3, and updated with yum update. I have kernel 2.6.18-128.1.10.el5xen.
I can't get my wirelss network to work, I have AR928X wireles network adapter.
Do I need to install a newer kernel and install ath9k or can I just downlad a driver without updating the kernel?
I'm new to CetOS and Linux so I hope someone kan give me a step by step guide to what I can do!
CentOS 5 Networking :: CentOS Does Not Acknowlege Hawking RT-73 USB Network Card?
Aug 25, 2010I just upgraded from Ubuntu 9.04 64-bit, to CentOS 5.5 64-bit and my RT-73 USB network card doesn't seem to want to function. It always worked fine in Ubuntu by default (plug and play). Is there some setting I need to make to get this working?Even BT-3 (which is quite old) recognizes the RT-73.
View 19 Replies View RelatedCentOS 5 :: Cannot Get 1M IO With Block Devices?
Nov 19, 2009I am trying to do 1Meg IO to one of the block devices but I can only get a maximum of 512K IO size. I can use the corresponding sg device to get 1Meg of IO. I was wondering if anyone knows why 1Meg IO to a block device is being broken down into 2 512K chunks? I have increased the /sys/block/sdg/queue/max_sectors_kb to 16384, but it has made no difference.
My uname is : Linux virgo 2.6.18-128.el5 #1 SMP Wed Jan 21 10:41:14 EST 2009 x86_64 x86_64 x86_64 GNU/Linux
CentOS 5 :: How To Delete NBD Devices
Aug 15, 2011I have created a number of network block devices that I would like to delete, but I have been unable to find any information to do this.
I am using Centos 5.6 and my kernel is 2.6.18-238.el5.
I have been searching the internet for two days now and have noticed some other UNIX systems do have utilities for deleting unwanted devices but nothing for linux.
I created these devices with the vmware supplied PERL script vmware-mount.pl which in turn calls mknod.
The commands would look like:
mknod /dev/nbd0 b 43 0
mknod /dev/nbd1 b 43 1
......
I have tried deleting them from /dev which works temporarily but they come back when I reload the nbd module i.e.
modprobe -r nbd
modprobe nbd
and also if I reboot.
There is a directory tree for each device under /sys/block and I'm guessing this is how /dev is getting repopulated. I cannot remove the directory trees from /sys/block. I get this when I try:
rm: cannot remove `nbd15/queue/iosched/slice_idle': Operation not permitted
rm: cannot remove `nbd15/queue/iosched/slice_async_rq': Operation not permitted
...... there are 25 lines like this ....
When I do a vgsan I see this:Reading all physical volumes. This may take a while...
/dev/nbd0: read failed after 0 of 4096 at 0: Input/output error
/dev/nbd0: read failed after 0 of 4096 at 2199022141440: Input/output error
and in the messages log I see this:
Aug 15 21:04:06 udon-desktop kernel: nbd15: Attempted send on closed socket
Aug 15 21:04:06 udon-desktop kernel: end_request: I/O error, dev nbd15, sector 0