CentOS 5 Networking :: Sis 190 Card Not Working Well With CentOS 5.3?
Apr 13, 2009
I installed CentOS 5.3 on my Shuttle SS-31T with SiS 190 network adapter. While booting the message "Bringing up eth 0 [ OK ]" appears. After booting it isn't possible to surf to an internet location (p.a. www.google.com). It's also impossible to ping other machines in the network. After typing ifconfig everything seems to be ok.
ipv6 is turned off
IP : 192.168.0.3
Subnet : 255.255.255.0
Gateway : 192.168.0.1
View 9 Replies
ADVERTISEMENT
Nov 20, 2010
I have a Centos 5 server on my LAN for testing the websites that i develop.It worked perfectly until this morning , after cold start -up, it seems that my network card is not enabled . Everything works normal:gui and terminal but no internet access. I'll run some commands on my Linux box and write the results , by hand , to this forum .
* uname -r : Linux Server 2.6.18-194.26.1.el5 i686 i386
* ifconfig eht0 : eth0 : error fetching interface information
* ifconfig -a : I get only results for loopback (lo)
* less /etc/modprobe.conf : alias eth0 sis900
* lspci |grep -i eth : 00:04.0 Ethernet controller :Silicon Integrated Systems [SiS] sis900 PCI Fast Ethernet (rev 90)
[Code]...
View 1 Replies
View Related
Sep 13, 2010
I've installed from the CD the Centos version 5.5. When I try to connect to Internet I can't because I received some errors. I've the Intel Corporation 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller also a wireless slot (I've the wireless card DWL-G650+) When I turn on the pc and I go to "Ethernet Device", I see set: peth0 (Intel Corporation 82801CAM (ICH3) PRO/100 VE (LOM) ETHERNET CONTROLLER) and also set "Bind to MAC address": fe:ff:ff:ff:ff:ff I've set manually the IP address (I'm under router). Status is "Active" but can't go on the Net. When I change to "eth0 (Intel EtherExpress/100 driver)...sometimes become "Active" an other times said that the MAC address is different or to check the cable because can't find the IP. What can I do?
View 5 Replies
View Related
May 4, 2009
I am using asus p5ld2-x/1333 motherboard,I installed the centos ,Centos saw other drivers but didn't see ethernet card.I am not connection the internet.
View 2 Replies
View Related
Aug 25, 2010
I just upgraded from Ubuntu 9.04 64-bit, to CentOS 5.5 64-bit and my RT-73 USB network card doesn't seem to want to function. It always worked fine in Ubuntu by default (plug and play). Is there some setting I need to make to get this working?Even BT-3 (which is quite old) recognizes the RT-73.
View 19 Replies
View Related
Jun 15, 2010
If i run lspci it shows lan card model, but lan card is not working. How do i check my lan card driver is installed or not?
Is there any way to list all installed drivers with hardware information like we have device manager in windows.
View 4 Replies
View Related
Jul 20, 2011
I installed CentOS. NetworkManager successfully installed and launched. I can ping any IP from terminal but I can't open any site in browser except 127.0.0.1 I can't open IP of the modem 192.168.1.1 in browser also.
The results of some commands:
ifconfig
eth0Link encap: EthernetHWaddr 7D:60:00:00:00:00
inet addr: 192.168.1.5Bcast: 192.168.1.255Mask:255.255.255.0
inet6 addr: fe80::7f60:ff:fe00:0/64Scope:Link
[Code]....
View 6 Replies
View Related
May 16, 2009
I have a Linux box with a Biostar TA690G Mobo and a Nvidia 9600GSO graphics card. Everything was working fine until I tried to boost the RAM from 2 to 4 Gb. With the 4b RAM the Nvidia card stopped working. There is only a blank screen. If I remove the additional 2Gb everything goes back to normal.
View 5 Replies
View Related
May 28, 2010
I am not very experienced using Linux but I never had big problems with Ubuntu. Now I am busy writing my PhD thesis and therefore I had to install CentOS to use one lousy program that I could not get to work under Ubuntu. However, it seems to be quite fine and it is working well besides one fact: The network card stopped working. In the beginning it was working fine although the speed was only on the level of 100mbit. The switch and the LED on the card indicated gbit connection, though. I tried to install the driver for the 8168 card which reduced the card to 100mbit (indicated by the LED on the switch and the card).
Ethtool indicated it was gbit capable but I couldn't activate it. After reading more and more I figured I have to use the 8169 driver again and live with the 100mbit. Unfortunately, after uninstalling the old driver and reinstalling the driver 8169 the network isn't working at all anymore. The network-manager displays the card as inactive and when I try to turn it on it complains about the wrong mac address, which I am not able to change to the proper one. I am using CentOS 5.5 with the latest updates.
View 17 Replies
View Related
May 1, 2009
I just have CentOS installed and cannot get the Agere et131x network card to work.I have tried the following:Reboot the computer and still did not see the network hardware.
Fai
lspci
Quote:
[code]....
View 7 Replies
View Related
Jul 4, 2010
i like to use my DVB-C Card KNC-One on Centos 5.5 x86_64. But i cant get it to work. on a 32 Bit Centos this is working like a charm. I tryed several different kernels together with the video4linux-kmdl
At the moment i am using this kernel: 2.6.18-194.3.1.el5.centos.plus
[Code]....
View 8 Replies
View Related
Dec 18, 2010
I have loded centos 5 on vertual machine, my host machine is windows xp and has two NIC cards working perfectly well
1) realtek RTL 8139 family PCI fast eathernet NIC
2) realtek 8169/8110 family gigabite ethernet NIC ( ONBOARD)
but both of them are not getting detected by CENTOS
View 1 Replies
View Related
Feb 13, 2009
Can anyone please tell me the files that a network card needs to use - know it needs a file called ifcfg-eth0 in etc/sysconfig/network-scripts
What other files has information relating to eth0
View 1 Replies
View Related
May 19, 2009
i did configure as it was advised on [URL]... but it didn't work. for eg I added eth0:1 and eth0:2 on /etc/sysconfig/network-scripts/ when i do ifconfig i can see only eth0:1, i cannot see eth0:2, eventhough i configured as it was on the tutorial
View 4 Replies
View Related
Jun 5, 2009
i have installed centos 5.1 but it won't recognize 2nd nic card (eth1). i was unable to install the driver supplied by the cd. i am using intellinet gigabite pci network card. the network card recognize by centos 5.3 but i need to use centos 5.1. i also tried another intel gigabite adopter but it also won't recognize by centos 5.1.
View 2 Replies
View Related
Dec 11, 2009
I need to change my lan card orderI have 3 lan cards eth0, eth1, eth2and I need my current eth2 as my primary lan card
View 4 Replies
View Related
Aug 16, 2011
I have a ESXi 4.1 build 433742 server with a CentOS 5.4 virtual machine.I installed VMware Tools.I added a vmxnet3 network card on virtual machine for 10GbpsBut my problem, the card doesn't UP ! the resultat of my commands :
[root@centos1 ~]# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
[code]....
View 1 Replies
View Related
Feb 11, 2010
I am looking for a gigabit network card for my centos 5.4 server. I am looking for something known to work well with linux. I have been on the bestbuy site and I found a DLink (DGE-530T) card with support for linux from the vendor but after reading feedback from users with that card I am not so sure it is linux friendly. I am now thinking of buying online.
View 2 Replies
View Related
Feb 9, 2009
I have a problem to configure my wifi card, a dwa-110 from D-Link, it is not recognized when I launch System / network device control (only ethernet connections appear), and it is the same thing in Administration / network / network configuration. But if I launch administration / hardware / system devices, the last line is "Ralink 802.11 bg WLAN"... When I try to add in the window "network configuration" (from above) some new stuff, I specifying the kind of hardware (wireless) and when I have to enter the name of the card I don't see my card. On other OSes, I used ndiswrapper, but I wasn't able to install it on CentOS (dependencies required and it's hard with only a USB key to install the stuff...) How to see if the card is recognized, if I have to use ndiswrapper and so on. I have an internal PCI network card also, maybe it is this card which is recognized.
View 2 Replies
View Related
Apr 28, 2009
I have a desktop PC with CentOS 5 installed, and a wireless card that's working well via NetworkManager.
How would I configure the wireless card statically, e. g. by editing /etc/sysconfig/network-scripts/ifcfg-wlan0?
This would be something like :
DEVICE=wlan0
BOOTPROTO=static
ONBOOT=yes
IPADDR=192.168.1.252
NETMASK=255.255.255.0
ESSID=my_essid
CHANNEL=3
But I don't know how to define the WEP key here.
View 2 Replies
View Related
Jun 7, 2010
I recently installed CentOS on a really old computer and while most things are running well, I am unable to connect to the internet. Using a Damn Small Linux live CD I am able to connect just fine and was able to see that that 'hp100' was being used as the netcard driver. When I tried to set up the network card using that adapter (HP10/100VG ....) it gives me the following error code...
View 1 Replies
View Related
Aug 23, 2010
I've done some research for CentOS and Linux support in general for this card, and I haven't found the answer I'm looking for. Does anyone use this card in a system of theirs, and, if so, how easy was it to set up? It's on an Asus M4A785T-M/CSM motherboard that I'm looking to purchase (Newegg link here for reference). I've seen a lot of Realtek cards have zero problems in Linux before, but I know each chipset is different.
View 4 Replies
View Related
Oct 2, 2010
I can't get wake up on lan (wol) to work on my network card.The strange thing is that before I had it working with the exact same hardware. But I was on Centos 5.4 then. Now I am on Centos 5.5.Am I correct in concluding that the sky2 driver does not support wake up on lan?
View 4 Replies
View Related
Jan 21, 2011
I had installed a Centos 5 server, with one network interface card and work find. Now I want to install ADSL (PPPOE) dial-up for internet in this server, so need to add a 2nd network interface card (RTL8139D or other) . After plug the network card, what I need to do in Centos to find this new card and config it?
View 1 Replies
View Related
Oct 29, 2010
I've installed a new fresh Centos 5.5 ..and after a lot of work..something starts to work (X now works with the new ATI HD5145 using ATI drivers) but i've a serious problemThe ethernet controller JMC250 JMicron PCI EXPR. doesent work at all so my notebook is out of the world !!!Here is some infos:rpm -q centos-release
centos-release-5-5.el5.centos
rpm -qa kernel* | sort
kernel-devel-2.6.18-194.el5
[code]....
View 6 Replies
View Related
Dec 3, 2009
i am trying to get centos 5.4 installed and bootable on my 16gb flash drive, with persistent overlay using and ext3 formatted drive.i want to be able to boot into centos and be able to have all updates from yum, etc, saved when shutting down for my situation i cannot use vfat.
View 9 Replies
View Related
Mar 18, 2009
I've been racking my brains over the past few days trying to figure out why my NIC card (network interface card) won't show up in the ifcfg-eth0 file.When I configure a new server (like this one) I always go to:/etc/sysconfig/network-scripts/ifcfg-eth0 and from there I usally see the name of my NIC's manufacturer's name and the hardware MAC address.Then it's only a simple process of entering the server's IP address, netmask and gateway and I'm up and running in no time...But not in this case! the ifcfg-eth0 file is completely blank! There's not ONE single line of config info in it... (?)The server runs an Intel core 2 duo (dual-core) CPU with 1 gig of RAM.
I've even re-formatted the drive and re-installed Centos 5.1 on the darn thing 3 times and it simply won't work.The server cannot resolve when I do a wgetIt also gives me a 'resolution problem in the named configuration'.What I don't understand is that the 2 small LEDs on the Cat 5 cable lights up and flash at what appear to be regular intervals here.
View 6 Replies
View Related
Jun 30, 2009
I've just set up a PC with CentOS 5.3 runing on near identical hardware to an existing 5.2 machine. Motherboard is Asus M2A-VM which I discover by chance generally works very well with CentOS. Ethernet is on board Nvidia.The older machine just did run gigabit speed without any intervention at all, rather to my surprise. The newer machine insists on running at 100 Mbit which is annoying as it is connected to a NAS through a gigabit dumb switch.
The obvious difference between the two is that ethtool on the older machine says that supported ports are TP, and so the port is TP. Whereas the newer machine says that supported ports are TP or MII and insists on running MII. I cannot change this with ethtool -s eth0 port tp. Perhaps not too surprisingly, mii-tool says that the supported speeds range up to 100 Mbit.
View 13 Replies
View Related
Jul 24, 2009
i finished installing CentOS 5 and managed to connect to the Internet. My Network Interface Card (NIC) is "Atheros L2 Fast Ethernet" and it is not in the device list. anybody can tells me what i should do now to be connected to the Internet?
View 8 Replies
View Related
Aug 4, 2009
I have a Sprint U760 air card that apparently works under Linux. Sprint has a guide: "Wireless Mobile Broadband Setup Guide for Linux OS" that I am using to setup the air card. When I go through the procedure in the manual for "Setting Up PPP Using KPPP" the last task is to query the modem to see if Linux recognizes it. When I do the query I get a response "unable to open modem". I have tried going back through the PPP setup but still get the same response.
View 8 Replies
View Related
