CentOS 5 Networking :: Looking For Realtek 8112L Card Setup?
Aug 23, 2010
I've done some research for CentOS and Linux support in general for this card, and I haven't found the answer I'm looking for. Does anyone use this card in a system of theirs, and, if so, how easy was it to set up? It's on an Asus M4A785T-M/CSM motherboard that I'm looking to purchase (Newegg link here for reference). I've seen a lot of Realtek cards have zero problems in Linux before, but I know each chipset is different.
View 4 Replies
ADVERTISEMENT
Sep 8, 2009
I just recently installed CentOS 5.3 and to make a long story short I found the entry for my wireless card under the network settings but when attempting to activate the card the system locks up. I have to reboot at that point as nothing responds (keyboard, mouse, etc..).
Running the command /sbin/lspci -v reveals the following about the wireless card:
01:00.0 Ethernet controller: Realtek Smeiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller (rev 20)
View 3 Replies
View Related
May 28, 2010
I am not very experienced using Linux but I never had big problems with Ubuntu. Now I am busy writing my PhD thesis and therefore I had to install CentOS to use one lousy program that I could not get to work under Ubuntu. However, it seems to be quite fine and it is working well besides one fact: The network card stopped working. In the beginning it was working fine although the speed was only on the level of 100mbit. The switch and the LED on the card indicated gbit connection, though. I tried to install the driver for the 8168 card which reduced the card to 100mbit (indicated by the LED on the switch and the card).
Ethtool indicated it was gbit capable but I couldn't activate it. After reading more and more I figured I have to use the 8169 driver again and live with the 100mbit. Unfortunately, after uninstalling the old driver and reinstalling the driver 8169 the network isn't working at all anymore. The network-manager displays the card as inactive and when I try to turn it on it complains about the wrong mac address, which I am not able to change to the proper one. I am using CentOS 5.5 with the latest updates.
View 17 Replies
View Related
Feb 16, 2010
I have downloaded the driver installed it, and it works fine. But i can't get to turn it off. I do have the ability to unload the driver's kernel modules and the sysyem does not see my card after that. That's ok, but i'm thinking it still uses my battery power. The wifi led is always on no matter what i do. The fn+<wifi key> doesn't to anything.
View 8 Replies
View Related
May 21, 2010
I have installed 9.04 ( I currently have it on dual boot with Windows XP) and my problem is that I have no internet connection. I have a Motorola modem with a Realtek RTL8139 Family Fast Ethernet NIC network card ( it's a wired connection, btw) When I plug in the cable, there's a little animation, but after a while I get the message: Wired connection is not active (or something like that) Here's what I did so far:
1) I ticked the Wake-On-Lan option in XP, since I read it in the forums that I could solve my problem. It did not
2) I turned off my modem, rebooted my system.
3) I deleted the Auto Ethernet network, and plugged in the cable again...no use.
4) I did an ifconfig, since I know that is what you guys really want
evajulia@Derek:~$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:18:f3:ab:2b:3a
inet6 addr: fe80::218:f3ff:feab:2b3a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
View 9 Replies
View Related
Dec 26, 2010
Running Linux mint 10 After the installation the wireless connection worked but it was very weak and intermittent. The icon would show 1 bar or none. iwconfig showed the rate at 1Mb/s. The same card worked fine in windows and on a 32bit version of linux. Installed new driver from realtek. Now the iwconfig readings look good and the icons shows 2 and sometimes 3 bars. But it will not connect at all! I even turned off all security on my router but it would not connect.
View 14 Replies
View Related
May 23, 2010
I am using DELL VOSTRO 1510 laptop , it has realtek r8169 ethernet card, i installed RHEL 5 in my laptop , i checked for the driver cd provided by DELL, they given one source rpm and two other rpm for ethernet card, i tried to install them through "rpm -ivh (path)/realtek-r8169 (full name).rpm " but it asking about dependency . i tried it by using yum also but still its not working.
also i tried to create binary rpm through source rpm, but it only generating spec not binary rpm, when i am using " rpmbuilt -ba (spec file) " its showing command not found error. RHEL5 have ethernet driver for realtek-8129 in their list but not for realtek-8169, i checked it in system-config-network window, now what to do, how do i install this rpm , i want to access net through RHEL 5.
View 1 Replies
View Related
Feb 23, 2010
I have no internet connection. I am running dual boot windows XP and ubuntu. The card works fine in windows, but doesn't work at all in Ubuntu. This is the card I am using Realtek rtl8139/810x Family Fast Ethernet Nic. I am using Ubuntu 8.10, codename intrepid. I hate windows because of the viruses I contract everyday, so I decided to use Ubuntu, but this does no good without networking. so I can get online. What I do now? It is an onboard LAN card, cable is plugged in a green light is on, ubuntu just doesn't recognize it.
View 2 Replies
View Related
Sep 12, 2010
I have a Toshiba Satellite series laptop, i get ubuntu on it, all works well but there's a problem, my wireless card doesn't work, it doesn't show me the aviable wireless network, my Wireless Card is an Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) but it works in windows. I used Ubuntu 8.04.4 LTS. When i run these codes that's what it shows:
[Code]....
View 4 Replies
View Related
Oct 12, 2010
I am trying to install EDUP 802.11n Wireless USB Install (RTL8188SU) on my recently installed ubuntu platform and I need a driver for it. I downloaded the one from the Realtec website and I got a bunch of files that I have no idea what to do with them. (h[URL]... I am compleatly new at Linux and I have no idea how to install anything. I am pretty nifty with Windows but this is my first time trying Ubuntu and Linux. So can I have some step by step guide to install this. I am good at following clear instructions correctly.
Aditional Info: I tired the hardware thing already or whatever its called and only NVIDIA drivers are there and my USB is not recornized because it needs a driver.
View 9 Replies
View Related
Dec 12, 2008
There seems to be some trouble with 8139too not working in a previous post. Has anyone found a solution to this? ubuntu version 2.6.24 (Hardy Heron?). Followed all known possibilities but information is all mostly out of date. module 8139too.ok? does not load. Following makefile on 8139too.c supplied, after altering to suit my version, comes up with 3 pages of errors?. ifconfig shows nothing for eth0like the last person markjuggles i have hit a brick wall here. Am I wasting my time?
View 10 Replies
View Related
Jan 11, 2010
The card is recognized by Ubuntu 9.10 and I have it in the network manager. I followed one tutorial about creating an ad-hoc network and all looked good, until I actually wanted to connect (or to be more precise, my machine is a host for other computers). The wireless icon just loops endlessly, without connecting and eventually I get "Wireless network - disconnected" message.
So, the main issue here is - connecting! I just can't. Also if you know/have some good tutorial for ad-hoc,
Code:
ivan@ivan-desktop:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:"internat3"
[Code]...
View 2 Replies
View Related
Feb 12, 2010
this isnt happening on ubuntu but I think this is more or less a kernel problem that could happen with any flavor. After a new install off of a live cd my wireless card is not picking up any signals...i was able to use wireless while using the live cd but now after it has been isntalled to the hard drive it is not working. even tried in terminal to manually look (iwlist wlan0 scan) but it isnt picking up the signal
View 2 Replies
View Related
Dec 31, 2009
I have HPDX2480 computer system where i have installed RHEL4u5 having kernal 2.6.9-55. now how can i install and configure my NIC?
View 1 Replies
View Related
Feb 11, 2011
I'm using Kubuntu 10.04.2 LTS on a Bangho laptop. Kernel 2.6.32-28-generic i686. My card is: Realtek Semiconductor Corp. RTL8187B Wireless 802.11g 54Mbps Network Adapter iwconfig wlan0 gives me:
Code:
wlan0 IEEE 802.11bg ESSID:"Default_WLAN"
Mode:Managed Frequency:2.442 GHz Access Point: 00:06:4F:8D:B9:AF
Bit Rate=1 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr: off Fragment thr: off
[Code]...
Usually when this happens, for 10 or 20 seconds it appears to be connected (i.e. the heart symbol is there) but I can't ping google or my router, then it "realizes" it's disconnected. It takes one or two attempts to reconnect successfully by pressing the "active" button. Meanwhile throughout the disconnections and re-connections the signal is very strong (98%).
I had the same problem with my old access point, at first I thought it was the cheap/old hardware, so now I bought an "ENCORE ENDSL-A2+WIGX2 | ADSL 2+ Modem with 4 Port Wireless Router". The problem persists only with a stronger signal.
View 1 Replies
View Related
Jun 8, 2009
I installed CentOS 5.3 Final on a machine today and was having some problems with the NIC. When I installed CentOs the NIC would not work, I looked in the network configuration and saw that neither of my two NICS had IRQ's so I arbitrarily gave them some and they both worked fine. I then ran yum -update, installed updates and rebooted my machine. Again, the NICs stopped working, only this time setting the IRQ did nothing. I did some googling and found this thread: [URL] The output from the first two commands is as follows:
[root@localhost ~]# uname -rmi
2.6.18-128.1.10.el5 i686 i386
[root@localhost ~]# /sbin/lspci | grep ther 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10) 05:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10) I followed the steps outlined and my issue still remains.
View 12 Replies
View Related
Jul 12, 2010
my wireless home network is not recognized by my network card (RealTek RTL8190 mini PCI). The post was as follows: "I am using a new computer with Windows 7 , Athlon quad core 2.60 64 bit, 8GB RAM. Internet conection works fine with ethernet but ubuntu does not see my wireless network. card (RealTek RTL 8190 ID: 10ec:8190). Have searched this forum but unable to come up with a fix. I was looking for windows XP drivers to use Ndiswrapper but could not find a list of .inf files. My network is OK and works perfectly in windows and with my 2 laptops. Can anyone point me in the right direction? Additional info: install was done within Windows using WUBI to a separate partition on my HDD. I am new to this and thouroughly confused as to the procedure for installing the drivers if they are in fact available."
I am very frustrated in that I would like to use Ubuntu 10.04 but it is useless without internet connectability. I am new to linux and do not understand where to get the appropriate drivers or how to install them. I wish someone would answer this post and either give me a clue what to do or just say "give up" and uninstall ubunutu.
View 2 Replies
View Related
Jun 15, 2011
I have had a vz modem card for some time now and it worked fine. However my employer upgraded from a PC5750 device to the new PC770 device. When I plug the old device (now deactivated) it shows and use to work fine. When I plug the new device in Ubuntu does not pick it up and show it in the networking options. I use to see it i n the upper right where I would select my wireless networks. I do get a green light on the card so I know its powered. So what do I need to do to get my Laptop to see the new card?
uname -a Linux mylt 2.6.32-32-generic #62-Ubuntu SMP Wed Apr 20 21:54:21 UTC 2011 i686 GNU/Linux
View 2 Replies
View Related
Mar 26, 2011
How can I get Suse 11.4 to see my wireless adaptor? Would love to get this working so I don't have to upgrade my old XP OS to Win 7.
linux@linux:~> /sbin/lspci -nnk
00:00.0 Host bridge [0600]: Intel Corporation Core Processor DRAM Controller [8086:0044] (rev 02)
Subsystem: CLEVO/KAPOK Computer Device [1558:4101]
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge [0604]: Intel Corporation Core Processor PCI Express x16 Root Port [8086:0045] (rev 02)
00:02.0 VGA compatible controller [0300]: Intel Corporation Core Processor Integrated Graphics Controller [8086:0046] (rev 02)
Subsystem: CLEVO/KAPOK Computer Device [1558:4101]
Kernel driver in use: i915 .....
View 9 Replies
View Related
Nov 1, 2010
I have Slackware(x32) 13.1 installed on my computer. Everything runs just fine except it doesn't seem my wireless card.I looked around and found a driver on the Realtek website. But, after I installed it, linux wouldn't boot. It would just hang. The driver did help my get the card detected, though.
On lspci, I found:
02:00.0 [Realtek company name here] RTL8101E/RTL8102E
03:00.0 [Realtek company name here] Device 8172
On windows, it said I had RTL8191SE. I am confused as to which card I have and which driver I need.I reinstalled the driver and rebooted. I then turned off my ether card via bios. Then I rebooted. Linux then booted just perfectly. However, I couldn't get the wireless to work. I was freaking and then left to go do something else with my hands. Then I realized I had the card turned off.
I mentally punched myself. >.>
View 2 Replies
View Related
Sep 13, 2010
I've installed from the CD the Centos version 5.5. When I try to connect to Internet I can't because I received some errors. I've the Intel Corporation 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller also a wireless slot (I've the wireless card DWL-G650+) When I turn on the pc and I go to "Ethernet Device", I see set: peth0 (Intel Corporation 82801CAM (ICH3) PRO/100 VE (LOM) ETHERNET CONTROLLER) and also set "Bind to MAC address": fe:ff:ff:ff:ff:ff I've set manually the IP address (I'm under router). Status is "Active" but can't go on the Net. When I change to "eth0 (Intel EtherExpress/100 driver)...sometimes become "Active" an other times said that the MAC address is different or to check the cable because can't find the IP. What can I do?
View 5 Replies
View Related
May 4, 2009
I am using asus p5ld2-x/1333 motherboard,I installed the centos ,Centos saw other drivers but didn't see ethernet card.I am not connection the internet.
View 2 Replies
View Related
Aug 25, 2010
I just upgraded from Ubuntu 9.04 64-bit, to CentOS 5.5 64-bit and my RT-73 USB network card doesn't seem to want to function. It always worked fine in Ubuntu by default (plug and play). Is there some setting I need to make to get this working?Even BT-3 (which is quite old) recognizes the RT-73.
View 19 Replies
View Related
Jan 22, 2011
I'm new to Debian, and new to Linux at all (well, I have used Linux sometimes in the past; Red Hat 7.1, Knoppix 3.6, Ubuntu, and some other distros but by no meaning I could call myself a real, full-time Linux user). But that's what I want to change. After some research I've decided on Debian. At first I wanted to download a stable build (5.0.7) but I've seen 6.0 RC1 was released just recently and I've changed my decision to get this version instead. Anyway, I'm currently downloading the DVD (slow connection, 2Mb/s only) and I've spotted this page in the meantime.
Thing that got my attention is "Potential installation problems with RTL8169-based network cards". I've checked my motherboard (Gigabyte GA-EP45-DS3) and I have Realtek 8111C on it. As far as I understand, it's not RTL8169-based but any real problems with my Realtek 8111C card, I don't want to install an OS from which I couldn't browse web. I know I had big issues with it while installing Mac OS X Snow Leopard but that's what I could expect when installing OS on unsupported hardware. So any way to install Debian 6.0 RC1 on a computer with Realtek 8111C network card?
View 2 Replies
View Related
Nov 7, 2010
I have just downloaded realtek rtl98192se for my wireless pci card. after extracting the file, the user guide states to go to the top level of the directory and execute the command 'make' to compile the driver
I have done so but I get the error: make: *** /lib/modules/2.6.18-194.el5/build: No such file or directory. Stop. Make: *** [all] Error 2
View 9 Replies
View Related
Aug 24, 2010
It is detecting the wireless networks in the surrounding area but it isn't connecting.
View 11 Replies
View Related
Jan 7, 2011
i have MB:Gigabyte 770t USB and Cpu Phenom II x2 555 BE My sound card didnt work and i have no sound at alll. only hardware that reconized as sound output in my sound setting is 5700 series HDMI which blong to my VGA.
View 9 Replies
View Related
Jun 22, 2010
I m unable to use my lan card on rhel5 linux lan card no :- is realtek 8168/8111
View 1 Replies
View Related
Jan 17, 2011
anyone tried to run wifi-card based on this chip? In coming days I will build myself a proprietary driver for 2.6.27.7 kernel. I mostly aware about patches for wpa_supplicant. Should I use a source for wpa_supplicant from slackware 12.2 distro or a new version? Do you know about any other prerequisities (requirements, dependencies) for building this proprietary driver?
View 2 Replies
View Related
May 1, 2011
I am facing a problem with the management of my network card after installing Ubuntu 11.04 32-bit Desktop edition.
There are two Network Cards and one USB adapter which I'd like to drive:
- Ethernet controller Broadcom Corporation NetXtreme BCM5703X Gigabit Ethernet (rev 02)
- Ethernet controller Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
- Realtek Semiconductor Corp. RTL8187 Wireless Adapter
Actually I need the wireless adapter to connect to the AP, so both of the ethernet card should be disabled. Infact, when I try to access to the AP I must disable the eth0 card by using (sudo ifconfig eth0 down), otherwise the route assigns the default gw (192.168.1.1) to the eth0 device and the network is useless.
View 2 Replies
View Related
