My monitor is an old, low-res (800x600 resolution) flatscreen, and the loader keeps trying to set it for 1024x768.the initial setup and package selection screens ran fine. it was only after rebooting to the "Welcome" screen that the problems started. I found the "resolution= (800x600 for me) under "additional boot options", but I don't know how to use it.
View 3 Replies
I'm a faithful user of Ubuntu Linux, especially 9.04 Jaunty Jackalope. I have a problem with my screen resolution on my LG Flatron L1718S. It's a 17 inch and its recommended resolution is 1280x1024.I was on this resolution all along until now. Now I'm limited to 800x600 resolution. Here's what happened. Before installing Ubuntu 9.04 on a friend's computer, I put in his Seagate 40 Gig hard drive into his Intel Celeron Box with a 2.93 GHz and 512MB ram. I then plugged my monitor into his system. Upon booting, I discovered that the hard drive had a very strange looking operating system called OS2 Warp...seemed like Black XP to me. On the desktop, the icons were so big and bloated,the mouse was frozen, there was so much eyecandy which demanded so much graphics resources.
His graphics card is an onboard one, framebuffer. I then rebooted the machine, this time running the Ubuntu 9.04 live CD. Resolution still ok, with 1024x768 this time. I installed Ubuntu 9.04 and finished. I shut down the machine, unplugged my monitor and plugged it back into my machine, which is a Intel Celeron with a 2.4GHz processor, 1,5GB RAM, 80GIG X 2 Seagate IDE hard Drives, 2 DVD Drives, an LG Spermulti-DVD rewriter and a BENQ DC W2000 rewriter.My graphics card is NVidia GeForce NV34 FX5200 Series, 256MB RAM Graphics Card. Suddenly everything on the desktop is so large, and the maximum resolution now is 800x600. It becomes 640x480 if i add Nvidia drivers, version 173. If I switch over to Windows XP, Service Pack 2, I have no resolution issues there. Nvidia drivers are loaded there as well. No issues with resolution there. To test the screen again, I plugged my monitor back into my friends computer that I mentioned earlier on. The resolution is stuck on 800x600. After plugging the monitor back to my computer, I tried to edit the X.conf using "sudo nano", adding the desired parameters, like undetected screen resolutions, monitor name, device,etc, but nothing worked.
I always had to resort to the backed up configuration file for XOrg. The latest Ubuntu 10,04 Lucid Lynx picks up my monitor with a maximum resolution of 1024x768.The Mandriva One 2008 Live CD also gave me the same result like Ubuntu 10.04, this time giving me more higher resolution options. Strangely enough, from my Ubuntu 9,04 and older, after several tests, the resolution is still stuck to 800x600. When I press the AUTO RESET button on my monitor, the screen says "Processing image Auto Adjustment-For Optimal display, change resolution to 1280x1024". A factory reset did not help. The resolution was perfect until I plugged my monitor into my friend's computer, the one with the 2,93GHz processor. I took another friend's monitor, a HP Cathode Tube Monitor, a 17 inch as well, and plugged it to my machine to test the resolution. The results were glorious! All resolution options were shown, from the lowest "320x240" to beyond "1280x1024". Plugged it back to mine, the same result showed: 800x600 resolution, the lowest being 320x240. I kindly ask for advice on how I can be able to get all the screen resolution options available on my Ubuntu 9.04, like before, because it shows the maximum of800x600, lowest- 320x240 on "display" in "System--Preferences".
Loaded Cent O/S on VMWare Workstation to begin learning for enterprise role.. The largest screen resolution is 800x600. Is this the max or how can I change it to a larger res.?
View 4 Replies View RelatedI use a VMWare ESX Server and installed CentOS.
Within the CentOS I can only use the Screen Resolution 800x600.
As I have a VMware installed I use the VMware grafic adapter shown in the hardware selection.
Even if I configure the VM graphic adapter within the ESX to use 1600x1200.
Is there any change to configure a higher resolution?
I've installed CentOS 5.5 on my Acer Aspire One D150. It uses the Intel integrated graphics chip GM945 which isn't supported "out of the box" by CentOS. My screen resolution has defaulted to 800x600, but it should be 1024x600. tried xrandr, and editing the xorg.conf file, and now have gone down the rabbit hole of trying to install xf86-video-intel and its associated dependencies (nested like Russian matryoshka dolls). I'm at the point of trying to install xorg-server, but am getting hung up by its dependencies on xproto and fontsproto, despite having installed them.
View 5 Replies View RelatedRecently when I rebooted the display resolution went to 800x600, where as before it was 1024x768. For some reason 1024x768 is no longer listed in (GNOME) System->Preferences->Moniters. Even after reinstalling Debian from scratch it's not there anymore. What can I do to fix this? System->Preferences->Moniters says Moniter: Unknown and stays that way even if I click Detect moniters.
# xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 640 x 480, current 800 x 600, maximum 800 x 600 default connected 800x600+0+0 0mm x 0mm
[Code]....
I am using Ubuntu 10.10. I am facing a problem with display resolution. My monitor is a 14" Samtron (56v) and with Ubuntu i am stuck with 800x600 resolution. I tried everything from 'xrandr' to 'sudo dpkg-reconfigure -phigh xserver-xorg' so that i can have 1024x768 resolution. But it seems that nothing is working out.
View 7 Replies View RelatedIn my laptop i have an ATI radeon HD 3200 , I installed Fedora 10 and also the fglrx driver I have 3d acceleration and works well. The problem is that the display makes a weird sound when i use a resolution higher than 800x600, and the display appears like "Unknown". The Display is a : 14" HD Acer CineCrystal LED LCD.
View 4 Replies View RelatedI am RHEL 5. I just installed it and when i try to config display it how only two resolution by default 640x480,800x600.No other resolution option is shown. I tried by editing xorg.conf but of no use.
View 2 Replies View Relatedi recently installed fedora 11 i386 from fedora 8 i386. it was a fresh install. with 8 i had a 1024x768 res and my monitor is a 15.4" Polaroid LCD tv that has a max res of 1280x800. when i goto display and try to change the res it only shows 800x600 and below.
View 11 Replies View RelatedIm running fedora 11. I pressed the desktop effects button yesterday, and it suddenly changed my resolution to 800x600 when it was previously a lot higher. I couldn't fix it, so i reinstalled fedora 11. Couldn't fix it. Reinstalled Windows XP, then reinstalled fedora 11, and it fixed. Now, 12 hours on, it has gone back to 800x600. How can i fix this?!
View 4 Replies View RelatedI've been using Ubuntu for about two years now, then suddenly today (after my PC accidently lost power) the screen resolution changed to 800x600 (it is, in fact, a widescreen monitor, and this resolution looked 'zoomed in'). The only two resolutions detected with xrandr were in the 4:3 ratio (800x600 and something worse). I followed some instructions, trying to reset the resolution to 1024x576.
I got as far as
$ xrandr --newmode "1024x576" ...
then,
$xrandr --addmode default 1024x576
but when I
$xrandr --output default --mode 1024x576
I a message to the effect of 'your screen can only support 800x600 or less'. Ah-ha, I thought, you stupid machine; this screen has had a greater resolution for over a year.
And so, from System->Preferences->Monitor, I forced the computer to switch to this new resolution. When prompted, I reset.
My current problem is that when I turn the computer on, the monitor displays a floating 'Input Not Supported' sign. I Ctrl+Alt+F1'd, and now all 'xrandr' and 'cvt' commands return:
Can't Open Display
My first priority is to get the computer back to it's less-broken 800x600 state;
EDIT: I'm running Ubuntu 10.04
After the latest kernel update (2.6.32-26), my computer will no longer start up with a screen resolution higher than 800x600. Before this update, my computer would sometimes startup with this problem, but this could usually be fixed with a restart (or two if necessary). At this resolution the panels and a lot of tool-bars will not display properly, so I am limited as to what I can do using the GUI.
my video card is an S3 unichrome (I think. It is built-in to the motherboard so I don't know for certain) my screen is an old ctr one I am running Ubuntu 10.04 on the 2.6.32-26 kernel
here is output of lspci
Code:
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 21)
00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0)
00:01.0 ISA bridge: Silicon Integrated Systems [SiS] SiS85C503/5513 (LPC
[Code]...
I have a good Asus monitor in which I can have a resolution of 1280x800 when using Mac Os (I have a Power Mac G4). However, when I try to have a better resolution with Ubuntu, the only resolution that it lets me choose is 800x600! There are no choices. I tried the "detect display" button but it doesn't change anything.
View 8 Replies View RelatedMy Fedora 12 is not showing screen resolution beyond 800x600. When I installed latest ATI Radon drivers, screen has become blank and I had to re-install.
View 1 Replies View RelatedI am using HP Mini 1000 Series with Ubuntu 10.10 (later installed with xubuntu-desktop). I want to run a wine application which requires 800x600 resolution. However, my current resolution is 1024x576. The other available solution is 640x480. Previously, I used pre-installed Windows XP, it allows me to change the resolution to 800x600 by clicking the "List All Modes" button at the display setting, then I can choose the 800x600 resolution. So, I think HP Mini is also able to support 800x600 screen resolution. May I know how can I do it in Ubuntu?
View 1 Replies View RelatedI have tried EVERY solution that has been posted. the nVidia forumswon help. Every solution that involves editing the .conf file crash my system. I wanna have real resolution for my monitor not be stuck at this 800x600 bull$#!tnVidia Graphics CardPlanar PL1700 Monitor
View 1 Replies View RelatedI recently installed Ubuntu 10.04 in my computer, I ran update manager and installed all the actualization but and I can not set the screen resolution higher than 800x600; I have windows XP installed in another partition and the screen resolution can get to 1028x1024 at 85 hz. I have a Pentium 4, 2.20 ghz, 1gb ram, and the video card is a SiS (Silicone Integrated Systems) 300/305/630/540/730 32 Mb.
View 4 Replies View RelatedI am having some trouble trying to change my screen resolution from the current 800x600.I tried to install driver but it didn't. output of lspci: 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 771/671 PCIE VGA Display Adapter (rev 10)
View 1 Replies View RelatedI am using a 15" CRT Samsung monitor and when I upgraded 10.10, the screen resolution became 800x600 and I am not able to increase the resolution of it. This was working fine with 10.04 version.
Below is the o/p for "xrandr":
xrandr: Failed to get size of gamma for output default
Screen 0: minimum 800 x 600, current 800 x 600, maximum 800 x 600
default connected 800x600+0+0 0mm x 0mm
800x600 0.0*
I also see a continuous message box at the top left corner of my monitor with text as "Unknown".
This is my first posting as a Linux Newbie. I have installed Ubuntu 10.04 inside of a MS Virtual PC on my Vista machine. Everything seems to work beautifully and is stable. However, I would like to use a resolution higher than the current maximum of 800x600. I've poked around on the web and have tried various tips. I tried using the xrandr options which added a higher resolution mode, but when I would try to set the output to that resolution, I would get an error message to the effect that I could not exceed the current maximum of 800x600.
I tried to cobble parameter values together and create an xorg.conf file, but every iteration seems to produce a bunch of colorful vertical bars within my Virtual PC window, and I would have to blow away that virtual PC setup and rebuild it (along with reinstalling Ubuntu). As I said, 800x600 is not a show stopper, but I would like to take advantage of the real estate I have with my display. These "fifty-five year old" eyes could benefit from the larger size. FYI, I did take a stab at installing Virtual Box, but got the infamous "blue screen", so I would rather stick with what appears to be a stable virtual PC base.
I'm stuck at 800x600, and no matter what i try i seem to hit a dead end. I've got the Intel Mobile 945GM/GMS rev 03, and it seems like lots of people have had to fiddle to get it working. Here's the info I've collected and tried so far. Ubuntu Edgy On Intel 945GM Graphics & Wide Screen LCD NoteBooks � 100% Linux Addict
HOWTO: install drivers and set up widescreen res. with Intel 945 vga card and Ubuntu - Ubuntu Forums Mostly Harmless: SuSE, Acer aspire 5580 and non-standard resolution 1280x800 Intel 945gm And 1280x800 Laptop Monitor Problem Suse 10.2 - openSUSE Forums I'm not too proficient with linux yet, so the right solution might be here and I'm just not getting it right. Maybe i'm not on the right path at all.
Barebones installation. Manually start x with 'startx'. For some weird reason, the resolution randomly sets to either 1024x768 or 800x600. How do I permanently set a resolution?
View 1 Replies View Relatedi have just put a Geforce 7300 GT graphic card into my machine the problem is the max resolution I can get is 1024x768 at 60 hz the screen is a benq fp71g+. also the screen goes blank when i click on the display icon in system settings. i know that the screen can be run at 1280x1024 so I don?t know where the problem is.
View 3 Replies View RelatedI've installed Ubuntu 9.10-karmic koala-and all runs good except screen resolution. I don't have any graphic card, and with windows I never had problems...but with linux max resolution is 800x600. what can I do to set a resolution of 1024x760 or similar ?
View 2 Replies View RelatedSo I know now that I reach the login screen, and I know to hit control, alt, f1. However, all attempts to reset the resolution have failed. Here's how it went down. I was working with nvidia driver. Already was frustrated I couldn't get a working wide screen setting for my toshiba hd tv/monitor but that's a seperate issue. I was trying to get the driver to recognize my separate monitor to an hd tv in the living room using the video out. works fine with windows. I got it to recognize, it made me save settings, and then restart. Note resolution settings are set to automatic right now. Then when I restart, I get to ubuntu splash screen, it plays the chime, and shows a blank black screen. Control alt f1 brings me the menu.
I have been told to type (this is just quick type, I used the proper commands in reality)
sudo dpkg-reconfigure xserver-xorg.
sudo dpkg-reconfigure -phighxserver - xorg
xrandr --output lvds --mode 1024x768
I found one article that gave a three step process.
sudo cp /etc/x11/xorg.conf / etc/x11/xorg.conf.custom
sudo sh -c 'md5sum ' etc'/x11/xorg.conf > /var/lib/x11/xorg.conf.md5sum'
sudo dpk-reconfigure xserver-xorg.
Nothing gave me any of the results I expected from command doesn't exist to completely irrelevant menus. Start me from the beginning to what I should do. Yes I logged in properly with my username and password to. Do the 'etc' in the command need to be filled with something else like a drive letter or something. I'm so lost, should I disconnect my tv? Also I tried running in safe mode and it said something about display not found.
I was trying to run a program, needs high graphic, suddenly my computer crashed. I had to restart it, now the resolution has changed, I mean its the same as before "1024x768" but the screen has been widened, it looks like it has been stretched, and zoomed. I changed the resolution, but it didn't help.
View 5 Replies View RelatedI am having video issue with ubuntu 9.10 and centos 5.4 cannot get resolution higher than 800x600 on Viewsonic vg930m monitor...The first time I installed ubuntu 9.10 worked great, since then no better than 800x600 on both linux distros. Any ideas it is very annoying, like using web browser on a small tablet pc....This monitor works great with opensolaris, though.
Using both distros in virtualbox right now but even if not virtualized install on hard drive I cannot get higher than 800x600...Driving me nuts.
I have installed Ubuntu 10.4 on Virtual Box, I have installed it successfully, the only problem is when I check the display settings it only have 2 options : 600 X 400 and 800 X 600 and this makes it difficult to work on Ubuntu as 800 X 600 is half the size of my desktop. How I can increase / configure the display settings so that atleast I can fit ubuntu screen into my screen size.
I did install the addition application, restarted the OS but still I don't see any display resolution 1200 X 800, tried pressing ctrl+D nothing happens, after installing I saw it updated mouse cursor now i don't have to press ctrl key again n again to enter into the ubuntu OS but still struggling with the resolution as it's too small, please guide me (here is the screen shot of my screen after installing the addition app).
