I have tried to install tp link tf3200 network adapter without success . the os is 8.04 hardy loading drivers is new to me. the driver is sundance (i think) and the output from the make command is shown below.
pag@paghomelinux:~$ cd /media/cdrom0/TF-3200/LinuxDriver
pag@paghomelinux:/media/cdrom0/TF-3200/LinuxDriver$ sudo make all
sudo: unable to resolve host paghomelinux
[code]....
i just installed Ubuntu 11.04 64bit on my desktop. i have a TP Link TL-WN321G (Ver 4.0) wireless usb adapter to connect to my wireless network (i used to use it with Windows XP).As expected (i'd read up a bit before installing Ubuntu), the adapter was autodetected - i could see my wireless network listed in the networks list dropdown, and lsusb showed it too.lsusb identifies "Bus 002 Device 002: ID 148f:2070 Ralink Technology, Corp. RT2070 Wireless Adapter"But i cannot connect to the network. When i select my network, it keeps trying to connect, but never succeeds in connecting.
i tried going through the forums for possible solutions, but most of them deal with how to get it working when the adapter is not detected, or when networks are not shown. Or they are for older Ubuntu versions.i use the same wireless network on my laptop (Ubuntu 9.04), and it has a WPA & WPA2 Personal security, with a password, which i've configured in the desktop as well.
I've installed it and it looks great. my problem is that I cant connect to the net since I could not find the driver for my onboard network adapter. it is a Gigabyte GA 945 GCM S2L board. of coarse I searched their site but it says that Linux driver I have to achieve from 3rd party. the adapter's chipset is a Realtek RTL 8111C but I could not find the driver for it. the only one that I've found - doesn't work. I must point out that when I've searched driver for my Nvidia display adapter- I've found it on Nvidia's site and it works great.
View 2 Replies View RelatedI have been running FC8 on this IBM T23 with a D-Link wireless adapter. Using MadWifi this has worked fine with Network Manager disabled. But now I have nuked that installation and replaced it with FC10. Network Manager is nice, and I would like to use it. And it kind-of works. Network Manager recognizes my router and all my neighbor's routers, but I can't connect.
[Code]....
I recently reformatted and dual partitioned to both Windows 7 as well as ubuntu 10.10. Loading works fine and Windows 7 is 100% operational. I cannot seem to get my wireless network adapter to be read by Ubuntus 'Windows Wireless Drivers' gui. Here are the steps that I have done THUS far, to make sure that we are all on the right path. Before I go any further, my wireless network adapter is an old school WUSB11 Linksys Wireless Network Adapter (running version 2.6).
1) Downloaded and installed "ndiswrapper" from ubuntu's main website. I downloaded the common, utils and ndisgtk files and installed them accordingly.
2) I extracted these three files to the desktop of Ubuntu and accessed the terminal page.
3) From terminal I typed "cd Desktop" to change the directory to the desktop.
4) Next, I typed in "Sudo dpkg -i ndiswrapper-common_1.54-2ubuntu1_all.deb
Sudo dpkg -i ndiswrapper-utils-1.9_1.54-2ubuntu1_i386.deb
Sudo dpkg -i ndisgtk_0.8.5-1_i386.deb"
5) This installed Windows Wireless Drivers gui successfully and I can access it.
6) I have downloaded the driver files for the adapter from the cisco website and searched them for the required files needed.
7) After extracting the .INF file from the "Drivers" directory named "NETUSB.SYS" (I wasn't sure if the other associated files within the same folder needed to be present together with NETUSB so I moved everything to the desktop) I typed in "sudo ndiswrapper -i NETUSB.inf". After accessing the Windows Wireless Drivers gui I have noticed that the 'netusb' driver is present yet under it, the system states "Hardware present: No". This leads me to believe that maybe I installed incorrectly or my "fireware?" is not present? I was reading through the installation guide posted on the ubuntu website that in addition to the .INF file we also need the BIN file(s)? and SYS file(s)?.. The folder with the drivers for my adapter contains a BIN file but it is not within the "Drivers" section of the folder.
9) Upon mousing over the network Icon naturally my hardware is still not present.
10) From what I gather after the system finds the hardware I am to write into the terminal
[Code]....
I have a Belkin Enhanced Wireless USB Network Adapter Model # F6D4050 v2. The drivers are for windows but the windows wireless drivers app doesnt work. I see a tutorial for a linksys that appears to have the same chipset, but I am not sure if any of the steps need to be modified, also my kernel is a bit different. Here is my kernel:
[code]...
I have just installed Ubuntu 9.10 on an Acer TravelMate 290E. I've got internet connection through the Ehternet Cable, but when I plug in the D-Link WLAN USB device, although the system recognises it, it is disconnected. How can I connect the WLAN USB device adn get it to work?
View 5 Replies View RelatedI want to install the DLink N150 (DWA-125) Wireless USB adapter in Ubuntu 9.04 if if go to
system-> administrator->log file viewer->dmesg
[ 8.840794] type=1505 audit(1286918554.305:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2041
[code].....
i don't know how to enable wireless.
It worked with 10.10, but in 11.04 only partially. It would show up in Bluetooth Manager, and I was able to pair with my phone. But after that it always failed to connect. Tried lots of things before I spent $10 on another nameless Chinese one and that worked fine immediately.
View 1 Replies View RelatedI have "D-Link DWA-125 Wireless 150 USB Adapter". I can use this wireless adapter on my laptop, i can use it on my desktop as well but only when windows is running, im a newbie to fedora, today is my 2nd day and 3rd night, so pretty exited about it. i have installed fedora 13 on a different hard-disk on my desktop. when the computer is booting, there is an orange light on the adapter glowing, it turns off when the computer reaches the fedora loading screen. If i see fedora's Network Configuration window under the hardware's tab i see the "D-Link DWA-125 Wireless 150 USB Adapter" listed along with my lan card. Now if i go towards the clock on the top right to get the wireless connection working, it shows wireless network disconnected. I have tried creating wireless connection manually by inserting the SSID, macadress, BSSID, ,WPA passkey etc, but still doesnt works. when i try connecting using hidden wireless connection, i receive window for inserting keyring password again and again, stating that the login password does not match. but during all this time, i still havent seen the orange light glowing activity on the external usb adapter. If i restart the computer in windows the adapter/wireless connection works. also have checked the Network service, it seems that the service is up and running. i really require some assisstance on this,
i have noticed this, that if i go under network configuration. the first tab over there, inside devices i cant see my D-Link adapter, but if i switch onto the hardware tab it shows my lan card as well as my D-Link adapter. so does it means that the driver is missing? or any service which is disabled, however at this point of time i can get only using wired connection. please assist me. with this issue, im also downloading the 500 complete update as well for fedora, hoping that it may make it work.
I've a damn TP-LINK WG422G UBS Adapter that i love i installed latest compat-wireless driver package and used latest ar9271 firmware after that it was worked properly. There is no problem when surfing the net, the problem is occurring usually download something via torrent sometimes form websites. I'm starting to download and then usb adapter suddenly freeze. If i remove and plug in the usb adapter it is working again.
View 1 Replies View Relatedhow to install D-link dwm-152 (3G/HSDPA) usb adapter on Lucid Lynx?
i've run lsusb and the result are:
Bus 005 Device 002: ID 0a5c:2162 Broadcom Corp.
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[Code]......
Have tried methods from every thread I could find for past 10 hrs. Have tried installing rt3070sta etc.Monitored message log; appears that the driver isn't recognized, though the USB port sees that something is plugged in (when I plug in the adapter, and unplug it).All of the threads miss something; I can't get a wireless port listed under ifconfig no matter what I try. Seems that every method leaves out something (I guess because everyone's box is different in some way). Network manager doesn't help much. Downloaded Wicd, which does even less.I guess I could try ndiswrapper, but I'm scared away by the hundreds of pages I see on going that route; I'm almost certain it wouldn't work (1000 possible points of failure).Does anyone have a strategy to recommend?AM64 box, newly installed Edubuntu 10.04, ran update manager.
View 3 Replies View RelatedI'm having some issues getting connected with a TP-Link TL-Wn727N wireless USB adapter. I have no way to connect hard wired with the computer, but I have another working notebook to possibly download files. However, the second notebook is a Mac, so most of the posts I've found are not filling in all of the answers. Also forgot to note, I am using Ubuntu 10.10. I followed along with this and managed to get the card to find the wireless connection. However, the connection would never connect. After entering the security password the wireless icon would do it's thing and then pop up asking to ok the password again. I double, triple checked the password and it is correct. I found elsewhere that I should probably install wicd. This is where I've run into problems with finding the way to get files that I can download on the Mac and then installed on the Ubuntu computer. I managed to find this forum thread and downloaded this file I transferred the file from the Mac to the Ubuntu with a flash drive and tried to install. First the install said that Network Manager needed to be removed, so I removed it. Next it says "Dependency is not satisfiable: python-urwid." I'm not sure how to go about getting this dependency as it is not showing up in the package manager.
View 6 Replies View RelatedWiFi adapter TP LINK WN821N is not working in 10.10, WN821N is notworking.
[Code]....
may i ask if TP-LINK 150Mbps Mini Wireless N USB Adapter support by Ubuntu? (TL-WN723N) I plan to replaced IBM x60s default wireless adapter, coz it's suffered overheat issued.
View 1 Replies View RelatedI got two issues with my wifi usb adapter:
1) it cannot see any networks around
2) i cannot setup it in master mode to use my PC as a router
As far as i can see, the device is recognized and the correct driver (rt73usb) is loaded. I was able to connect to a laptop somehow (the laptop could see other networks and the adapter's PC-to-PC network). I'd like to make it work as a router, i.e. share my internet connection (eth0) via wlan0. Here is what i have:
Code:
Ubuntu 10.04
Linux 2.6.32-22-generic #36-Ubuntu SMP Thu Jun 3 19:31:57 UTC 2010 x86_64 GNU/Linux
TP-Link TL-WN321G wifi usb adapter as seen as
Bus 001 Device 006: ID 148f:2573 Ralink Technology, Corp. RT2501USB Wireless Adapter
$ iwconfig wlan0
wlan0 IEEE 802.11bg ESSID:off/any
[Code]....
1. D-Link DWA-643 Xtreme N Express Card Adapter The onboard wireless for my HP tx1000z stopped working a long time ago. This wireless adapter is in my express card slot.
2.
Code:
$ lspci
00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.1 RAM memory: nVidia Corporation C51 Memory Controller 0 (rev a2)
00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2)
[Code]....
my long awaited WUA-1340 D-Link wifi adapter has arrived, and...unfortunately won't work it didn't work "out of the box", so I tried the following (found on the aircrack website)Here's what I did....1. Edit /etc/modprobe.d/blacklist and add blacklist rt73usb as a new line.2. RebootThen,
Code:
wget http://homepages.tu-darmstadt.de/~p_larbig/wlan/rt73-k2wrlz-3.0.3.tar.bz2
tar -xjf rt73-k2wrlz-3.0.3.tar.bz2
[code]....
Ok, so I am needing some drivers and I've been googling like hell to find em, however, I can never seem to find any. My adapter model is F6D6050v1.
PS: when I try sudo ndisgtk it comes up with command not found.
I was wondering where to find the drivers for my D-link adapter. It says on the box that it has Linux support, what does that mean? I have already used it without any drivers and it works for a bit but after a week or something it doesn't work anymore (it is connected to the network but no download). What should I do? Would installing the drivers solve the problem?
View 3 Replies View RelatedI really want to drop Windows, but wireless connectivity and frequent crashes are really discouraging me. I have a dual-boot W XP with Ubuntu 10.10. I do not have the computer on, so I'm writing this from my weak memory
USB Adapter - Netgear WNDA3100-100NAS = v2
The adapter works under W XP with no problems
The router, Linksys WRT54G sees the adapter in the dhcp table
lsusb lists the adapter.
I have copied the drivers from the install CD onto the desktop. I cannot figure out how to install or access those drivers for the installation. I tried to install the ndiswrapper from the software center, but the center shows it's available from the "main" source. I've looked in the package manager, but can't find it. When I go into terminal, and enter one of the suggested commands in the forums, it can't be located. I have a Belkin F5D8010 installed on this computer, and it works great under W XP. I want to try to get this installed, but until I can figure out installation of the ndiswrapper and how to access it, and get the drivers recognized, I'm at a standstill.
I have just installed Ubuntu 11.04 on an old machine to get a feel for it. No problems with the install, but I don't have a LAN connection lead spare so I'm trying to install my Belkin Wireless G USB Adapter (K75-F5D7050B which requires version 3 according to the Belkin site).
Unfortunately I can't find any Ubuntu software & driver versions on their site and I only have a windows installation disc.
Complete n00b here. I am running openSUSE 11.3 and trying to load drivers for a network card. When I try to make install, I am getting this error:
Code:
Makefile:69: *** Linux kernel source not found in any of these locations:
Makefile:70:
Makefile:71: *** Install the appropriate kernel development package, e.g.
Makefile:72: *** kernel-devel, for building kernel modules and try again.
How do I install the kernel-devel?
Just made the jump to Ubuntu, and until this install I considered myself very tech savvy. Now not so much! Built my new desktop, loaded Ubuntu 64 bit no problem. But I'm having a terrible time figuring out how to load the native driver for my realtek wireless adapter. I successfully un-tarred the file, and used the terminal to run the make command by using cd command to navigate to the file. It returned a wall of text, and in my mind looked to work. Next I go to run "./clean" in the same file location in the terminal and it returns:
"ERROR: Module r8192s_usb does not exist in /proc/modules
ERROR: Module ieee80211_rsl does not exist in /proc/modules
ERROR: Module ieee80211_crypt_ccmp does not exist in /proc/modules
ERROR: Module ieee80211_crypt_tkip does not exist in /proc/modules
ERROR: Module ieee80211_crypt_wep does not exist in /proc/modules
ERROR: Module ieee80211_crypt does not exist in /proc/modules
Not completely sure if this is an issue, I try moving to the next step of instructions issuing the command "insmod 8712u.ko" in the terminal same file location and get the error message
insmod: error inserting '8712u.ko': -1 Operation not permitted
I've tried running "sudo insmod 8712u.ko" from both that file directory, and from my home file directory. My guess is I'm missing a step or need to be typing these commands in a different file directory in the terminal.
i try to install my d-link dwl-g520 h/w:A1 in master mode with madwifi drivers but:
$ lshw
*-network:1
description: Wireless interface
product: Atheros AR5001X+ Wireless Network Adapter
vendor: Atheros Communications Inc.
physical id: 5
bus info: pci@0000:00:05.0
[Code]...
I have recently installed Linux Mint 10 on my laptop. When I look at the Device Manager in Windows 7, it says I have an Atheros AR9285 Wireless Network Adapter. Right now, I am unable to connect to wifi with Linux. What drivers am I able to install, and how would I install them?
View 3 Replies View RelatedI've been trying to get online for the better part of a week now with no luck. I can't get my network up to download drivers for my hardware - without the drivers I have no GUI so I'm stuck trying to do this in text mode.
View 14 Replies View RelatedI recently received a used laptop that I was going to use for my kids, a Compaq Presario 2100. Everything went fine on the install, however I could not get the WiFi to work. The internal card, a Broadcom BCM4306, was attempting to use the b43legacy drivers, which I understand to be the native driver for this card, but would get all sorts of strange errors in 'dmesg', and would never get a solid connection.
After fiddling with this for 2 days, and reading countless troubleshooting guides, I finally gave up and decided to get it working with ndiswrapper. Everything worked perfect, except I can only get it to work if I first load b43legacy, then load ndiswrapper, then unload b43legacy. If I blacklist b43legacy, and just load ndiswrapper, iwconfig does not report a wlan0.
I ran across this posting, and decided to try this, but it also did not work. Plus, with this file in place, any attempt to use modprobe would complain about every line of that file.
A node on a cluster that our lab has had sitting in a dusty room since time forgotten does not seem to want to talk to the rest of the world any more.Following is the information I found was being asked for on other posts for similar questions, transcribed by hand.
View 6 Replies View Related
