For some reason when I try to boot Ubuntu up I get the following error messages:udevd[470]: NAME="%k" is superfluous and breaks kernel supplied names, please remove it from /etc/udev/rules.d/48-ldusb.rules:2One or more of the mounts listed in /etc/fstab cannot yet be mountedAfter the second error message, it says, "Stopping Firestarter..." and it stops there. :
View 9 RepliesI installed firestarter and then at a later date uninstalled/purged it, both actions via synaptic. I have a very verbose boot, I like to see what's going on, and noticed after the uninstall/purge that I was getting an error zooming up the screen containing firestarter in it. After many restarts I found that a file was left in /etc/network/if-up.d/50firestarter and this file was simply a script trying to restart firestarter. At this point I've commented out the calling line and followed the commented line with exit 0. This removes the error but there's still a link calling the file so, is this a bug or am I missing something? It appears the uninstall/purge wasn't entirely complete.
View 1 Replies View RelatedFirestarter sometimes shows up to a dozen different ip connections for a single webpage that I open. This is for the first webpage I open, not after I have been browsing for awhile so they are not old connections that have not timed out. This just doesn't seem normal to me since other installs I have had of ubuntu have only shown one or two firefox connections at all times.
View 1 Replies View RelatedI'm trying to set firestarter as a startup application using the gui but it will not run due to permissions problems,?
View 4 Replies View RelatedI have an Asus 900 laptop that I put Ubuntu 9.10 on.I know it was made by the Chinese, but why are they trying to hack my pc?I currently put FIRESTARTER a linux firewall on board you can go here to get itNow I can see everyone's IP address and find out where they are and who they are!!
View 9 Replies View RelatedI have wireless connection between my router and PC. It is the only computer connected. Sometimes Firestarter blocks ports 1900 and 6771 from 192.168.1.100 IP address and sometimes port 68 from 192.168.1.1 IP. I'm a bit confused because 192.168.1.100 is the IP addres i use to open ports in router and 192.168.1.1 is used to access the router settings..
View 7 Replies View RelatedI need to start firestarter at starup, but the application need root credentials, I use "Startup Applications" when I need a program to start upon login, but firestarter need input the su password... how could I get around this?
View 1 Replies View RelatedI was wondering if firestarter (software firewall) works out of the box or does it need some kind of configuration in order for it to provide protection? Is firestarter even needed with ubuntu?
View 6 Replies View Relatedi connect to internet with the connection (with Name: DSL Connection 1) that made by myself. now i wanna use the firestarter but i have a problem.
View 5 Replies View RelatedI allowed ports 3689 and 5353 for incoming and outgoing traffic in firestarter but my other machines wont detect a DAAP share. They do see them when I turn off firestarter. I'm even more confused when I see that I have a local connection using port 56690 when I turn off firestarter and monitor the log. It seems that DAAP is using 56690 but when I allow it for incoming/outgoing it still doesnt pick up my DAAP shares.
Is there a way I could fix this? I mean, I could run without a firewall but...idk if thats such a good idea :/
im having a bit of a problem with Firestarter, i have Transmission opened and i am downloading a movie but when i check Firestarter i see hundreds and hundreds of Ip's that are blocked, and like 10ip's every second that get blocked.
[Code].....
So I had my desktop connecting via wireless to my home network. And I had firestarter helping with the firewall, and it was running using the wlan0
But now I have connected that machine by ethernet to the internet and I have taken out the wireless card. So there is no more wlan0 connection.
But now firestarter doesn't recognize my eth0 connection. How do I fix this. Should I just uninstall and reinstall firestarter? I feel that there should be a way to configure it to realize the firewall should be on eth0 now instead of wlan0.
I am new to Ubuntu and till now I have chosen it to be my favorite distro. I use my laptop in various networks, home, work, school. When I run firestarter the wizard does not give me the option for wireless INTERNET, only ethernet.
View 2 Replies View RelatedI updated my system with system updates and when i restarted.I couldn't access the internet from my desktop. i got on laptop internet worked just fine..i disabled firestarter and mozilla connected to the internet just fine. I turned firestarter on. and i couldn't reach anything.. What do I have to do to get firestarter to allow me to connect to the internet via firefox
View 3 Replies View RelatedI've been using Firestarter for a while and have used it to set-up inbound and outbound policies (which are probably way too restricitve) but since turning on boot logging the other day I have noted that the boot log contains the message:
Code:
* Starting the Firestarter firewall [fail] I find this somewhat alarming. I have seen post[URL].ht= firestarter (although have not added it the auto startup list and do not wish to have it start without the root password). What I would like to know is as the computer boots up does it set the iptables to their last setting irrespective of whether firestarter starts or does firestarter need to start to set the iptables and therefore my policies?
All I want to do is share my internet connection that comes through the eth0 cable to my wlan0 wiki card. Firestarter seems the convenient tool for doing this. BUT it keeps telling me wlan0 not ready. The card is connected correctly and network-manager does see incoming signals.
View 1 Replies View RelatedI recently installed the XRDP server on my desktop edition of Ubuntu v10.04 following the simple instructions available here. I did this on two computers. One computer has Firestarter installed while the other does not.
When I use Windows to connect to the Ubuntu box without Firestarter, everything works just fine. However, when I try to connect to the one running Firestarter, I get a pop up showing an error message (see the attached file).
I checked the incoming rules in Firestarter and I don't see a way to add RDP sessions to the list of exceptions. I also tried adding my IP address in the host section but this too didn't help the situation.
what files does firestarter change? I would like to know so I can look at the files so I can learn to do the same thing without firestarter.
View 3 Replies View RelatedI am running Ubuntu 10.10 I have an question about the firewall Firestarter, when checking the firewall it told me there are 9 serious incoming connections what must I do with this info. Inbound is normally blocked as standard i have also see that someone with port 1234 and 12345 have trying to attempt mine system but failed all trojan ports are fully blocked.
View 2 Replies View Relatedi just installed Firestarter firewall and it is showing me 12 serious inbounds after an hour.Is it a serious matter ? What should i do ?
View 3 Replies View RelatedUbuntu 10.10 Firestarter 1.0.3
My Desktop gets moved around a lot, meaning, I switch between Wire and Wifi often. I have been re-running the Firestarter wizard (when I remember to do so) each time I change from one mode of communication to another.
However, in Firestarter, on the STATUS page I can see both my wired connection and my wifi connection along with transfer data stats, despite which kind of Internet connection I have told Firestarter my computer is using.
Does this mean Firestater is actually protecting both routes and that I don't need to rerun the wizard to customize Firestarter for protecting the newest mode of communication I am using between these two different choices of Internet contact?
At my home I am using firestarter to connect my XBOX 360 to the internet and it works perfectly, never crashes etc and I get a moderate NAT which I've never experienced any problems in having.
I have my devices set up like this
eth0 - ifconfig eth0 192.168.2.1 netmask 255.255.255.0 broadcast 192.168.2.255
XBOX - 192.168.2.10 netmask 255.255.255.0 broadcast 192.168.255 gateway 192.168.2.1
This configuration works perfectly on my router at my house which has the IP of 192.168.0.1
However at my friends house he has a router with the IP adress of 192.168.2.10 or 192.168.2.7*, I don't remember exactly but I'll find out tonight. I have tried changing my IP settings on my xbox and eth0 to no avail. I noticed instantly that the XBOX IP is the same as my friends router. what the new settings would be, or simply changing the router's IP.
However there is also an issue with the DNS servers. I can't find them anywhere on the router or on the router box itself. I heard that I could point it towards my default gateway however.
FTP Server OS: Ubuntu x64 9.10 Client OS: Ubuntu x64 9.10 I have an FTP server on my home network. FTP Server: VSFTPD with TLS My FTP server is running with iptables configured using firestarter. Firestarter Inbound Traffic Policy "allow Service / Port contains the FTP service with the appropriate port range, vsftpd.conf port range is identical, as is the port range on my router.
My Client system, only after reboot or system power on, absolutely will not connect to the FTP server unless the firewall is disabled then re-enabled by way of firestarter then re-enabled. Only then will my client successfully connect and continue to connect until my client reboots or powers on. At which point I need to disable/re-enable iptables through firestarter.
Others can connect to my FTP server, but they use a mixture of Mac and Windows with default firewall settings. Has anyone experienced this with firestarter and ubuntu 9.10? I never had this problem using Ubuntu 9.04.
I have a system running 9.10 configured with Firestarter acting as a router. We have multiple Xbox 360's on the network. Unless some ports are forwarded, the Xbox has a NAT type of "Moderate". I have been able to set an Xbox with a Static IP and forward the necessary ports for that IP, which allows the Xbox's NAT to become "Open." My question is, how do I do this for multiple Xboxs? If the follow the same procedure for additional Xboxes, only one Xbox at a time can have an "Open" NAT type, and the rest would be "Moderate". The ports the Xbox uses cannot be changed via the Xbox.
View 3 Replies View RelatedI am running ubuntu 10.10. I recently enabled the firewall and installed Firestarter to configure it. Bad decision apparently. I can't connect to the internet using Firefox unless I first stop the firewall using Firestarter. After I do that, Firefox connects to the internet just fine.
If I uninstall Firestarter, will the ubuntu firewall function as it did originally, before I configured it? Or will it continue to function the way it does right now, which doesn't allow me to connect to the internet?
Just want to stealth ports on my laptop. Had problems with firestarter when I installed in on 10.10. Set Firestater back to defaults and then dumped it with:
Code:
sudo apt-get purge firestarter
Set up Gufw to defaults and now am not sure what I am seeing with iptables.
iptables -L shows .....
Do these settings look correct for default settings for Gufw? or do I still have some problems with the old firestarter settings not being removed. All I want is all ports stealthed. I know that ping is enabled but I believe that is a default setting in ufw. Could I restore iptables to default with:
Code:
sudo iptables -F
and then enable Gufw and set default?
A couple of years back, just getting into Ubuntu, I installed Firestarter as an option to aid in networking. Realizing that it really didn't help in my plan, I now want to remove it.In terminal, I typed:
Code:
sudo apt-get purge -y firestarter
I rebooted, only to find out that I now have no internet connection.
[code]....
Running Fedora 10 and 11. Using Firestarter firewall.Does anyone know where Firestarter gets the Events which it displays?I do not find anything in /etc/firestarter/.I suspect Firestarter looks in a log file which Fedora keeps somewhere.
View 2 Replies View Relatedthis is in part a *****. The Yast2 firewall interface is inferior. Firestarter and Guarddog are much better - but they are not in the packman list of stuff you can install because you like it better. How many of you care to offer an opinion as to why these other firewall apps are NOT packaged for openSUSE installation?
View 5 Replies View RelatedI am working on ubuntu right now and it is quiet easy to install firestarter firewall on ubuntu thru GUI interafce but my requiremnet is to install firewall on target (powerpc 8560 ),so i have to compile firestarter source for target powerpc (montavista linux) and installed it on target. I have downloaded firestarter-1.0.3.tar & .src.rpm file both but not able to compile it for my target which is powerpc (8560).
1.How to compile source code for powerpc ( I have environment created for ppc compilation but do not know how to modify the configure file to change the compiler) because it is compiling firestarter source code with gcc compiler bydefault i. e for host. How can i change the compiler " CC "? 2.What will be the executable created to be installed on target after compilation ? 3.Is the cross compilation for target is possible?