My HP Laptop screen is 18.4 in diameter and the only two resolutions that work are the highest a 1920x1080 which is too small for me or 1360x768 which is perfect. That res is no longer available in the latest Nvidia driver.
View 9 RepliesCode:
Fedora 12
2.6.32.9-70.fc12.i686
GEFORCE GO 7400
When my notebook boots I get a high screen resolution. However, when I login it seems to go to a lower resolution that is not clear. I think this all started when I updated to a new kernel. So I reinstalled the nvida drivers using leigh's guide. However, I still can't seem to get it to display correctly.
Code:
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (mockbuild@) Sun Feb 28 14:49:02 EST 2010
# Xorg configuration created by livna-config-display
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection .....
I am new to opensuse and have installed 11.2 KDE. It is simply perfect for my system. However after the initial setup the display resolution was set perfectly fine for my 18.5" LED monitor, default resolution was 1366x768, and everything looked good from desktop to fonts but the OSS drivers didn't support compositing so I decided to switch to nvidia drivers. I installed the driver as shown in openSUSE repositories page, for my 6600GT card. Now after rebooting everything is stretched,even the fonts look really ugly and fuzzy.
I am unable to find any mode in Nvidia XServer settings that would correct the current ugly stretched display. I am unable to set 1366x768 manually as well, doing so my PC won't boot to KDM but rather sticks to console. Now it's for sure that my monitor and display card supports 1366x768 resolution but it's just that nvidia drivers/Nvidia XServer settings won't let me set that resolution. How can I set the resolution or even better if I can enable compositing using OSS drivers then that would be great an dm willing to switch back.
I recently set up Kubuntu for my parents, and its working fine, other than the screen resolution. When I log in, it uses 800x600 when it should be using 1280x1024. I've tried to generate/ edit xorg.conf, but Kubuntu doesn't seem to pay attention to it. Also, I don't know if it matters, but it seems to be detecting a second screen that doesn't exist (see picture). That "monitor" can only go up to 800x600, but when I disabled it, it stayed off. When it was on and I pressed identify monitors, however, it put both labels on the main monitor. Here's the picture of the two monitors:
View 8 Replies View RelatedI just got a DVI cable so I can have a dual monitor setup, (one VGA, one DVI monitor), and when the DVI cable is plugged into our 20" widescreen, the correct resolution (1680 x 1050), a "No Signal" error message will appear on the monitor. When the resolution is lower with the DVI cable, it will show up, but everything will be a bit bold and blurry. When I plug our VGA cable into the VGA slot in this monitor, everything shows up fine.
View 9 Replies View RelatedFINALLY got my personal server up and running again after my GPU's fan died. i rigged a new fan/heatsink on it but i can't seem to get the resolution correct. nvidia-settings (version 195.36.31) says 1280x960 but i have to pan around the entire desktop (like having a huge image zoomed in on a small screen).
View 8 Replies View RelatedI have some experience with Linux (mostly Ubuntu) but absolutely none with Fedora. In fact I have needed to re-install twice just to get to this stage. I now have a fully updated Fedora 14 Gnome desktop. I have (finally) got Nvidia graphics drivers up and running. I can open the Nvidia Settings screen and everything looks ok except that the desktop screen resolution doesn't seem correct. I have a Sony Vaio with default screen resolution of 1920x1200. In Nvidia settings it was set to AUTO, but I've changed that as root user to 1920x1200 with a refresh rate of 60 Hz and rebooted. My desktop looks quite good, but it's not 1920x1200 - maybe 1600x1200? Perhaps. How do I confirm the current resolution?
I have run
Code:
glx info | grep direct
and the output is
Code: direct rendering: Yes
GL_EXT_Cg_shader, GL_EXT_depth_bounds_test, GL_EXT_direct_state_access,
Which I presume is ok?
I installed ubuntu onto a desktop computer about a month ago. Everything was working well straight away, I had it outputted onto my TV (32 inch Hi Def Sharpe Aquos). The Graphics card is an NVidia Ge Force FX 5600. On installation and after a restart the computer detected the TV and actually gave the name of the TV in the settings automatically, in the system --> Administration Menu there is a programme that sets the resolution and settings for the NVidia card. This all sorted itself automatically and displayed in 1360 x 768 which was perfect on my TV. For some reason when I turned it on this morning it will only display in 640 x 480 or 320 x 240. xrandr only gives minimum of 320 x 240 and maximum as 640 x 480. How to rectify this?
View 3 Replies View RelatedI've just bought a new monitor - Viewsonic VA2213w and am trying to set it up with Lucid. The resolution required is 1920x1080 @ 60Hz. I have an NVidia GTS250 with the proprietary driver v195.36.24 installed. I can set the right resolution in the nvidia-settings app, but it will not survive a restart. X always reverts to 1024x768. I have manually edited xorg.conf now to try to force the mode. The GDM login screen displays at the correct resolution, but on logging in X changes the resolution. Xorg.0.log shows the resolution being correctly set to 1920x1080 initially, then right at the end for some reason it is reset to 1024x768.
xorg.conf
Code:
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildmeister@builder75) Thu Apr 22 11:45:35 PDT 2010
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder75) Thu Apr 22 11:44:23 PDT 2010
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
Option "Xinerama" "0"
EndSection .....
I am using Ubuntu 11.04 on an Intel D510MO motherboard as a low-end surfing computer. The monitor, a Viewsonic VA1926w, has a maximum resolution of 1440x900. However, the monitor preferences shows a maximum of 1024x768 only. How can I bring up the resolution to 1440x900? The screen seems sort of flattened because of the incorrect settings. I think the video card (built in) of the motherboard is an Intel 3150.
View 3 Replies View RelatedI recently built a new computer and moved over my old graphics card, a nVidia GTX 275. Everything appeared to work fine, it booted with no drama etc.
I use my computer for work and gaming, all my work, web browsing, chat etc happens on Debian. I play games on Windows 7.I did a fresh Debian install on this box and everything went smoothly until starting xdm for the first time, it wouldn't go to a higher resolution than 640x480. I'd already installed the proprietary nVidia drivers and they appeared to be working fine, just at the wrong resolution.
I tested OpenSuse 11.4 as a guest OS via virtualbox on a win7 32bit host. Output to my 16:9 screen was perfect with a plentiful choice of high resolutions. Now with Suse (32 bit) properly installed as the host the only resolutions are 1024X768 and below and I am stuck with 4:3 ratio. My PC is an Intel Atom D945GCLF2 which has integral graphics. The monitor is the VGA input of a Samsung TV.
View 9 Replies View RelatedAbout three weeks ago I bought a new PC and installed Debian Squeeze. I have a Samsung SyncMaster 2494hs monitor connected to it. Until about an hour ago the monitor resolution was 1920x1080 and there were no problems. Anytime I clicked on system -> preferences -> monitors, the monitor preferences displayed the monitor name (Samsung whatever) as well as the resolution (1920x1080). An hour ago I did my normal daily upgrade via synaptic (synaptic -> mark all upgrades -> apply). When the upgrade were finished, the system indicated that a restart was required, so I restarted.
After the reboot, my monitor's resolution is set at 1152x864. System -> preferences -> monitors shows the monitor name as unknown and the max resolution available is 1360x768. Xrandr shows the max available resolution as 1360x1360, which is obviously wrong. According to discover I have an ATI graphics card. I've also run ddcprobebut that outputs about 15 lines and then stops with edidfail. I do not have an xorg.conf on my system or, if I do have one, it is not in /etc/X11.
I recently got a computer and installed the ubuntu 10.04 beta on it. I'm having issues getting my monitor to display at the correct resolution. It should be displaying at 1440x900, but the highest resolution I can select from the displays configuration panel is 1366x768, which is not even the correct aspect ratio.
lspci:
Code:
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 12)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 12)
00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06)
00:16.2 IDE interface: Intel Corporation 5 Series/3400 Series Chipset PT IDER Controller (rev 06)
00:16.3 Serial controller: Intel Corporation 5 Series/3400 Series Chipset KT Controller (rev 06)
00:19.0 Ethernet controller: Intel Corporation 82578DC Gigabit Network Connection (rev 06)
00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06)
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06)
00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06)
00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 06)
00:1c.6 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 7 (rev 06)
00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a6)
00:1f.0 ISA bridge: Intel Corporation 5 Series Chipset LPC Interface Controller (rev 06)
00:1f.2 IDE interface: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA IDE Controller (rev 06)
00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06)
00:1f.5 IDE interface: Intel Corporation 5 Series/3400 Series Chipset 2 port SATA IDE Controller (rev 06)
This is the whole thing, in case it helps.
From what I have read, this is a brand new chipset with the GPU built into the main CPU, as if it were another CPU core. Is there a driver for this yet, or do I have to deal with an improper resolution?
I'm using two screens where one Is cheep Denver TV screen with DVD player. I have just install Jessie on my PC. Before i had Windows and there was no problems finding correct resolution for this screen. Now Jessie recognize it as Unknown and the maximum resolution I can set is 1024x768 what is way to small even for this screen. At Windows resolution was something over 1200px wide. The worst thing about it is that this resolution stretches the display really ugly. You may think I'm making big deal of nothing but for me it is actually a deal. I'm graphical designer and I need to see display as it is.
View 7 Replies View RelatedDebian Stable LXDE
Samsung LD190N
NVIDIA GT 730
Trying to set to native resolution of 1360x768 with error "Failed to get size of gamma for output default":
Code: Select allerik@DRAGON:/var/log$ xrandr
xrandr: Failed to get size of gamma for output default
Screen 0: minimum 640 x 480, current 1024 x 768, maximum 1360 x 768
default connected 1024x768+0+0 0mm x 0mm
1024x768 61.00*
800x600 61.00
[Code] ....
Found these lines in /var/log/kern.log stating "unknown Kepler chipset":
Code: Select allJul 26 17:35:34 DRAGON kernel: [ 15.510099] nouveau ![ DEVICE][0000:03:00.0] unknown Kepler chipset
Jul 26 17:35:34 DRAGON kernel: [ 15.510148] nouveau E[ DEVICE][0000:03:00.0] unknown chipset, 0xb06070b1
Jul 26 17:35:34 DRAGON kernel: [ 15.510191] nouveau E[ DRM] failed to create 0x80000080, -22
Jul 26 17:35:34 DRAGON kernel: [ 15.510419] nouveau: probe of 0000:03:00.0 failed with error -22
Google search yielded this bug, which affected GT 730 graphics cards, apparently patched in Linux 3.19:
[URL] ....
Assuming this is the problem, does this mean I have to upgrade to Testing or install proprietary drivers?
I just set up my dad's pc with Debian Sqeeze. It runs perfectly fine and after trying a lot of distro's Debian is the only one that will not crash or freeze up X. Now we're forced to using my own 17" monitor instead of his 19" wide screen since the max res is 1280 x 1024 in Sqeeze. What he needs is 1360 x 768. I found out in the wiki that xorg.conf needs to be edited. Since the file does not exist it needs to be created by running "Xorg -configure" in tty after stopping GDM. when running the "Xorg -configure" command this is the output;
" vmware: Please ignore above "FATAL: Module vmwgfx bot found."
(++) Using config file: "/root/xorg.conf.new"
(==) Using system config directory "/usr/share/X11/xorg.conf.d"
Number of created screens does not match number of detected devices.
Configuration failed. "
It's an Intel Sandy Bridge integrated graphics chip. I've tried running "Xorg:1 -configure" as mentioned in a forum but that simply gives me a "unknown command" answer.
I have two displays: my main being an Apple Cinema Display (1920x1200), and my secondary being a Compaq W17q (1440x900). Previously all applications saw the secondary fine, being able to detect its name, native resolution, refresh rate, and so forth. But today, for no reason, after going into nvidia-settings the display is now being called "CRT-0" with only 4:3 resolutions available (1024x768 being the highest).
So now I'm stuck with the wrong resolution on my second monitor. All I can guess is that something more integral in Fedora is no longer able to read the EDID in it or something (I say integral as it's not just nvidia-settings, its everything, not to mention my install of Win 7 still reads the display A-OK)? Maybe I could just force the 1440x900 resolution? If so, how? Everything I've tried so far has either had no effect or resulted in glitch city.
What is correct driver for 10.10 for a nVidia Corporation NV18 [GeForce4 MX - nForce GPU] (rev a3) (prog-if 00 [VGA controller]).
Originally, xorg driver 1.9 would work, now it won't.
Excited at seeing the new features in 10.04, I clicked the Upgrade button tonight. I am now really regretting it! Problems:
1. My screen resolution should be 1280x1024 but the System>Preferences>Monitors control panel only shows 1024x768.
I think I have onboard Realtek graphics. Do I need to install proprietary drivers? Everything worked fine out of the box with 9.10!
2. The sound isn't working. Again I think I have onboard Realtek sound, and again it used to work fine without any intervention from me...
3. Although on first startup wireless networking was working fine, I restarted to see if that would solve the display issue, and wireless networking stopped working too!
I have an RaLink wireless card.
When I used Grub to choose 2.6.31.20, I got some error messages at startup (e.g. mount couldn't mount /dev), but then it did eventually start up and the sound and wireless networking are working again. But the resolution is still not fixed. It is now offering 1152x864, which it didn't previously, but no 1280x1024 (my screen's native resolution).
I am running kde 4.4 in virtualbox , but cannot create xorg.conf to get a correct resolution. X -configure = segfault. Older releases were fine - lenny, even ubuntu hardy / lucid.
View 6 Replies View RelatedI have a new system I built this week. I have the nvidia drivers installed, but desktop effects, googleearth and Quake4 all try to load the /usr/lib/libGL.so.1 from mesa-libGL and fail to start.I have two other machines, both with nvidia video, and don't have the problem with them. I've looked for differences on the systems, but haven't located anything so far.
View 2 Replies View RelatedI am new to Suse Linux. So please excuse me for this "funny" query. have read the threads: Configuring graphics cards in openSUSE 11.3
From here I went to this page: SDB:Configuring graphics cards - openSUSE Its mentioned on this page that: Upon installing openSUSE, the X system's automatic configuration may have failed to properly configure the graphics correctly. Typically this results in either a black screen upon reboot, or the wrong resolution being displayed on the monitor.
I have none of these problems. But after searching for inability of desktop effects to become activated, I found that nVIDIA graphic card drivers are must for these effects. After clicking "My computer" icon on desktop, I found Display Info as following:
Vendor: nVidia Corporation
Model: G98 [GeForce 8400 GS]
2D driver: nouveau
3D driver: nouveau Gallium (7.8.2)
Can anyone tell me 'Is nouveau an alternative for nVIDIA'? Is this the reason for no wrong resolution or black screen upon boot. That means my computer graphics are working correctly. Then why does Desktop Effects are not getting enabled.
After searching for Kaffeine media player extra codecs to play media files, I incidentally found the following options: I opened Yast Control Center @ linux-o26a Software> Add on Products > installed Add-On Products > Community Repositories > clicking Next, this opened a window with "List of Online repositories" where there is an option of "NVIDIA Repository". If I install it, will it enable the "Desktop effects"
I can't seem to pass 1360x768 on my nvidia 9400 gt 512mb ram. The current driver is 260.19.36 and I've installed the recommended current found under additional drivers however I am still limited in resolution. How do I bump it up to my previously used (Windows 7) 1680x1050?
ubuntu 10.10 desktop x64
I'm using Ubuntu 9.10 64-bit with a GTS 250. After installing the restricted driver from NVIDIA's website I get stuck at a 640x320 resolution. The only other option I get is 320x240. The resolution I need is 1680x1050.
I've also encountered this problem with a 9600GT.
I currently have an nvidia 8600 gts w/nvidia restricted drivers and I cannot seem to change the resolution to anything higher than 640x480. Everything used to work perfectly w/the restricted drivers however I downloaded an update and it screwed everything up.
I have tried to edit my xorg.conf file but it seems that either i'm doing something wrong or the nvidia drivers are simply ignoring that file. I tried reverting back to the older versions of the drivers and that didnt seem to work. I tried installing the newest version of the nvidia drivers and that didnt work either. below is my xorg.conf file
[Code]...
I recently installed Ubuntu, 10.4
My problem is that when i log in, the resolution isnt what i want. So i change it via the Nvidia x server settings, and press Save to x config file
Yet when i log in again, it defaults back to what it was before i changed it?
Iv looked all over the internet for the past 2 days and nothing seems to work.
I'm using Nvidia's driver from their website and Kubuntu 8.04. I tried Debian 5.04 kde on the same computer and the resolution stays. Of course I prefer kubuntu. After shutdown the video resolution goes back to 1024x768 but I want 1280x800 instead. I have a Dell IN191ON lcd widescreen monitor and geforce fx 5200 video card. I'm using the latest video driver from Nvidia for this card version NVIDIA-Linux-x86-173.14.25-pkg1.run.
Here is my xorg.conf.
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildmeister@builder75) Wed Jan 27 03:03:53 PST 2010
Section "ServerLayout"
[Code]....
I have just installed ubuntu 10.04 32 bit on my girlfriend's computer. She has a NVIDIA GeForce2 MX/MX 400 video adapter and I am having trouble getting the restricted driver working. First I tried it by the books through the Restricted Drivers assistant under Administration. This was successful but on reboot both the boot screen and the desktop environment were at 640x480. No adjustment using the NVIDIA tools was possible. It said that the monitor was unknown. It is a Fujitsu Siemens D-19.1 monitor. I believe however the problem lies with the graphics adapter because I remember it being identified correctly at some point of the ordeal.
Next I followed a tutorial and removed all of my NVIDIA packages from the computer. I still have my graphical environment though. After downloading the appropriate (Newer version than that in the Ubuntu repo) driver from the NVIDIA website I entered
Quote:
It says that the installation has failed. I can supply log files of the failure.