Ubuntu Networking :: Unable To Use Zonet ZEW2500P Module - NetworkManager Won't Start On Booting

May 2, 2010

After upgrading to Lucid said adapter is nonfunctional - NetworkManager won't start on booting (I'm using 2870sta module) and it finds no networks - neither does WICD. The device itself is identified: "lsusb" gives a line "Bus 001 Device 005: ID 148f:3070 Ralink Technology Corp." "iwconfig" gives nothing under lo and eth0 and this under wlan0:

Code:

RTxx70 Wireless ESSID:""
Mode:Auto Frequency=2.412GHz
Link Quality=10/100 Signal level:0 dbBm Noise level:-143 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

And a "lsmod | grep -e rt2 -e rt3" gives:

Code:

rt2870sta 525366 0

(Note: I had a similar problem going from Jaunty to Karmic, but blacklisting rt2800usb in my blacklist.conf fixed it. No such luck this time.)Using a Zonet ZEW2500P.x86-64 Lucid.

View 9 Replies


ADVERTISEMENT

OpenSUSE Network :: How To Get USB Zonet ZEW2500P(04) Working - Error - NICLoadFirmware Failed

Jun 20, 2011

I have tried setting it up from YAST but no joy so far an I am clueless. The device is a Zonet ZEW2500P(04) USB wireless interface. From the sticky "My wireless doesn't work - a primer on what I should do next"

/usr/bin/lusb

Code:

Bus 001 Device 002: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless Adapter

/usr/sbin/iwconfig

Code:

wlan0 Ralink STA ESSID:""
Mode:Auto Frequency=2.412 GHz

[code]....

View 2 Replies View Related

Fedora Networking :: Unable To Start An Openvpn-connection Via The "nmcli"-command To Control NetworkManager

Jun 4, 2011

As I reported in this bug:[URL].. root is not able to start an openvpn-connection via the "nmcli"-command to control NetworkManager, whereas my user does not run in any problems with this command. My error output when starting as root is as follows:

Code:
# nmcli con up id "my-openvpn"
Active connection state: unknown
Active connection path: /org/freedesktop/NetworkManager/ActiveConnection/5
state: VPN connecting (need authentication) (2)
Error: Connection activation failed: no valid VPN secrets.

Does anybody know what to do about this strange behaviour? The vpn-secret seems to be stored in the gnome-keyring and in the /etc/NetworkManager/system-connections/my-openvpn simultaneously. But root cannot access any of these. Why this is important? I'm trying to set up a dispatcher-script to automatically start openvpn on eth-connection. but this does throw the exact error from above (no valid vpn secrets..).

[Code]...

View 1 Replies View Related

Networking :: NetworkManager Delays Booting: Connecting In 30 Seconds

Nov 30, 2010

That is what it says during boot (splash=verbose):

Code:
Starting KNetworkmanager
Connecting in 30 seconds
{counting down from here, no more text scrolling}

kdm starts (on screen 7) and I can give user name and password but on screen 1 is still this countdown. I have only mobile internet via (GSM / HSPA) and this is not connected when the wait is over.

I looked for a .conf file but those I found have no means to change this behaviour of the networkmanager. How can I set seconds to 1 or even 0?

View 4 Replies View Related

Fedora Networking :: 11 With 4965agn - Configure Wireless Connection Using NetworkManager Right After Booting Up

Jun 13, 2009

The symptom is that NetworkManager repeatedly ask for password to connect to my AP.My AP is secured with WPA-PKI. The problem even happens with Fedora 11 live cd if I'm not quickly configure wireless connection using NetworkManager right after Fedora completes booting up. It means if I promptly configure wireless connection, i'm still able to access Internet. Same thing happens for the first boot of Fedora from hdd. For the second boot or when I dont quickly configure wireless connection when system finished booting up, NetworkManger repeatedly asks for password for AP.

I did try several approaches posted in this forum but problem still persisted. Some of approaches I tried are:

[Code]....

View 2 Replies View Related

Fedora Networking :: NetworkManager Does Not Start After Updating F15?

May 28, 2011

I upgraded from F14 to F15 using the DVD. The network worked fine after the upgrade.This morning I updated to the latest RPMs and rebooted, and now the network donot work!ifconfig shows only the lo interface. NetworkManager does not start, /var/log/messages shows signal 11.I tried to boot with the original kernel, but the results are the same.

View 6 Replies View Related

CentOS 5 Networking :: NetworkManager Won't Start / Get It To Work?

Oct 12, 2009

I've been running CentOS on my laptop for a few weeks now. I don't know what happened today, but when I boot up, the NetworkManager wont show up on the panel, and I don't have access to wireless networks or Internet. I tried booting my Windows partition and the wireless works fine. I can't seem to remember any latest change I've made aside from the wallpaper =) Any ideas where I should start debugging? I could see the module "iwl3945" still loaded. Here's a manual type of my lsmod | grep iwl3945

iwl3945 90177 0
mac80211 137929 1 iwl3945
cfg80211 30793 2 iwl3945,mac80211

View 13 Replies View Related

Fedora Networking :: Latest NetworkManager Fails To Start

Mar 25, 2009

I just updated my Fedora 10 installation with the latest NetworkManager (NetworkManager-0.7.0.99-4.git20090324.fc10.i386) and now my NetworkManager fails to start. The output in the /var/log/messages is

[code]...

View 3 Replies View Related

Ubuntu Networking :: Unable To Get 3g Moblie Broadband Phone To Be Detected By NetworkManager

May 11, 2010

I am having trouble getting NetworkManager to detect my Huawei-Vodafone dongle and I can't figure out why. I went and checked on NetworkManagers website and I should be good to gobut no such luck. look at the following:

manpep@manpep-desktop ~ $
manpep@manpep-desktop ~ $ dmesg | grep -e "modem" -e "tty"
[ 0.000000] console [tty0] enabled
[ 47.951906] USB Serial support registered for GSM modem (1-port)
[ 47.951958] option 3-2:1.0: GSM modem (1-port) converter detected
[ 47.952990] usb 3-2: GSM modem (1-port) converter now attached to ttyUSB0

[Code]....

Although "lsusb" see it (as usually) as Huawei model E620, in fact it's a much more recent one. It's the K3520, from last year.

View 1 Replies View Related

General :: Unable To Start X When Booting With Acpi=off Or Modeset=0

Jun 30, 2011

Yesterday I thought I had solved my "Blank screen boot"-issue when I successfully got to the terminal login screen without the screen going black by booting with

Code:
Linux acpi=off
I spoke too soon. I found out shortly after that when trying to "startx" with acpi off gave me these errors:
Code:
WARNING: Error inserting i2c_algo_bit ("filepath"): No such device
WARNING: Error inserting intel_agp ("filepath"): No such device

[Code]....

Then I read somewhere that booting with "i915.modeset=0" might work. So I removed acpi=off from lilo and added this, and sure enough, I got to terminal login, but I get the same errors with "startx".

I must make it clear that I can successfully perform startx when I boot without "acpi=off" or "i915.modeset=0", I am unable to see the screen but I can hear the KDE fanfare, etc.

View 8 Replies View Related

Ubuntu Networking :: How To Get Zonet Zew2502 Wireless Use To Work

Mar 5, 2010

I just installed Ubuntu 9.10 and am trying to get my Zonet zew2502 wireless usb to work right. So far I have

-installed ndiswrapper from the Synaptic Package manager

-copied the netMw225.inf and MRVW225.sys to my download directory

At first, when I ran ndiswrapper -l I got NOTHING back. When I plugged in the zonet to usb and ran lsusb I got

Code:

Bus 001 Device 009: ID 1286:1fab Marvell Semiconductor, Inc.This doesn't appear on the list when the zonet is not plugged in so I can only assume that this is it. Anyhow, I did a sudo ndiswrapper -i netMw225.inf and everything seemed to install, so now when I do ndiswrapper -l I get:

Code:

netmw225 : driver installed
device (1286:1FAB) present

I don't think a GUI front end for ndiswrapper got installed to me search for and connect to wireless networks.

EDIT: The computer also has a PCI ethernet card (wired) that does work correctly, but I have the cable unplugged while debugging the wireless card.

View 6 Replies View Related

Ubuntu Networking :: Zonet ZEW2508 Drivers Won't Install

Jun 15, 2010

I've got version 10.4, also.

I have a Zonet ZEW2508 USB wireless adapter and the drivers that come with it won't install. Are there any drivers that work with Ubuntu?

Ubuntu does appear to see that it's plugged in, however.

View 9 Replies View Related

Ubuntu Networking :: Can't Figure Out How To Install Zonet ZEW1642

Oct 17, 2010

I've attempted to find the .inf for this card's driver, but to no avail. My plan was to use ndiswrapper to install the driver, but without the .inf I'm at a brick wall!

View 4 Replies View Related

Ubuntu Networking :: Zonet ZEW1642s Wireless PCI Adapter?

Apr 19, 2011

i'm a total ubuntu newbie(installed yesterday!), and i cant seem to get my network card to work. i have an 802.11n Zonet ZEW1642S Wireless PCI Adapter, and it came with a cd that contained the drivers necessary for installation on windows. i understand that the drivers are not compatible with ubuntu, but is there any method that i can get my wireless card to work? if so could someone explain (in newbie speak, sorry!) how to do it?

View 1 Replies View Related

CentOS 5 Networking :: Zonet ZEW2502 USB Adapter Doesn't Seem To Be Recognized

Feb 8, 2009

I just got 5.2 installed on my HP zd7000 laptop. I have a Zonet ZEW2502 USB Adapter but doesnt seem to be recognized. I tried to search in the forums and Google but didnt find any tutorial. point me in the right direction? or do I have to buy a different USB adapter?

View 6 Replies View Related

Ubuntu Networking :: Not Working: Zonet ZEW1642D (Ralink Rt3062 Chipset) In Studio

Oct 29, 2010

other forums to get my Zonet ZEW1642D to work on my new install of Ubuntu Studio 10.10. None of the how-tos I've found APPEAR to have worked although I guess I'm not entirely sure how I would know. There is a pair of computers at the top right of my screen by the date/time. When I right click there the following are all checked:

Enable Networking
Enable Wireless
Enable Notifications

but when I click Connection Information Auto eth0 is the only connection that comes up (which must be the wired connection I'm using to submit this) Here are the things I've tried:

1) README_STA included in the driver files downloaded from the Ralink website although I must admit this was a bit over my head
2) http://ubuntuforums.org/showthread.php?t=1045703
3) http://www.hyperborea.org/journal/20...i-ralink-3062/

[Code]....

View 9 Replies View Related

Networking :: Unable To Change Bnx2 From Built In To Module In Menuconfig

Jun 25, 2010

I am having trouble upgrading my broadcom drivers ( bnx2 ) for some reason i can't switch Broadcom NetxtremeII support from "built in " to module in menuconfig. can someone show me why this is the case?

[code]...

also i do have loadable module support enabled[*] Enable loadable module support

View 1 Replies View Related

OpenSUSE Network :: Can't Start NetworkManager

Jan 26, 2011

I seem to have somehow messed up my repositories and now NetworkManager isn't working.

I have two errors happening, which I'm sure are related. First of all, when I try to load knetworkmanager, I get the error:

Code:
knetworkmanager: error while loading shared libraries: libkminterminals.so.4: cannot open shared object file: No such file or directory Second of all, when I restart my computer, upon loading I get a message from Akondi Server Self-Test saying several databases failed. I've never seen this before, so I think fixing these errors would be best? Some of the errors are MySql failed, akondi not registered at dbus, etc.

Lastly, I don't have a wired connection so currently my machine has no internet. I'm using a second laptop to get necessary files and I transfer them with usb.

View 9 Replies View Related

OpenSUSE Network :: NetworkManager Will Not Start Automatically

Apr 15, 2011

Installed opensuse 11.4 and wireless network started automatically. Then I changed the name of the computer in YAST, and restarted. Now I cannot get NM to start automatically at boot. The red X shows up on the panel app Network Management and settings buttons do not activate the wireless device. I have to start NetworkManager from the command line. After about 30 seconds the wireless hardware symbol turns on and then I can connect to the network.

HP Pavilion Dv7
opensuse 11.4 64bit AMD
RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)
KDE desktop

[code]....

View 7 Replies View Related

Ubuntu :: Stopping Module Running At Booting?

Mar 9, 2010

Ubuntu 9.10 64bit
CPU - amd phenom II X4 955

I tried to stop kvm and kvm-amd modules to run at boot by adding; Code: blacklist kvm
blacklist kvm-amd at the end of /etc/modprobe.d/blacklist and reboot PC. However it doesn't work.

$ ls /etc/modprobe.d/ Code: alsa-base.conf blacklist-firewire.conf blacklist-oss.conf
blacklist-ath_pci.conf blacklist-framebuffer.conf blacklist-watchdog.conf
blacklist.conf blacklist-modem.conf libpisock9.conf

View 3 Replies View Related

Networking :: Rtl8187 Driver Module Load Error (Invalid Module Format)?

Jun 1, 2009

When I try to load the Realtek 8187 modules to kernel using the ./wlan1up command, I get the following error:

[root@localhost rtl8187_linux_26.1025.0328.2007]# ./wlan1up
insmod: error inserting 'ieee80211_crypt-rtl.ko': -1 File exists

[code]...

Can someone tell me how to correct the "Invalid module format"? I hope that correcting the "Invalid module format" error, I will not have the "Unknown symbol in module" error.

Note: I am using wlan1 for this module as I previously am online with the wlan0 network.The same error occurs if I use ./wlan0up.

View 3 Replies View Related

General :: Booting - Missing Module /dev/sde1

Dec 21, 2010

I have recently downloaded and installed Linux 10 mint to use instead of my current windows vista home premium. After downloading and installing when it went to boot it said the boot had failed and was missing module /dev/sde1

View 3 Replies View Related

Ubuntu Networking :: Unable To Start Moblock?

Jul 13, 2010

I have installed moblock, moblock-control and mobloquer from the AUR, however I am unable to start moblock. Mobloquer launches fine, and will update the blocklists fine. However, upon clicking "start" I receive the following;

Problematic Deamon status: 1 Moblock is not running* what do i do??? please help me i have tryed loging in as root and i maked it for compleat removal? then i reinstalled it but it still gives me the same error
it was working until i changed my MAC on wlan0 when i go to MoBlock status: this is what it says

Code:
Current IPv4 iptables rules (this may take a while):
Chain INPUT (policy DROP 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
4 381 blockcontrol_in all -- * * 0.0.0.0/0 0.0.0.0/0 state NEW mark match !0x14
0 0 ACCEPT tcp -- * * 192.168.1.1 0.0.0.0/0 tcp flags:!0x17/0x02

[Code]...

View 2 Replies View Related

Debian :: Unable To Locate The Networkmanager For KDE4?

Mar 6, 2010

Installing Debian Testing on a new laptop and wanted to test out KDE4 on this laptop.Somehow I am not able to locate the networkmanager for KDE4 or maybe I missed something?

View 3 Replies View Related

CentOS 5 Networking :: Unable To Start DHCP Client?

Jul 23, 2009

I have Centos 5 installed on a PC in the local network. I have installed the RPM dhcpv6-client-1.0.10-16.el5.i386.rpm on this PC to configure it as DHCP V6 client. The RPM was installed successfully, and I have done modifications to the following files:

1. /etc/sysconfig/network, set the networking to yes.
2. /etc/sysconfig/network-scripts/ifcfg-eth1 set the BOOTPROTO=DHCP.

Now the problem is when I start the client on this pc as dhclient, it throws the following errors, and logs out after some time. All the network configurations were lost and the PC gets disconnected from the network.

[root@ServerB]# dhclient
Internet Systems Consortium DHCP Client V3.0.5-RedHat
Copyright 2004-2006 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/

[Code]...

View 4 Replies View Related

Fedora Networking :: Unable To Start Wifi - WPA Passwd Always Requested

Jul 14, 2011

I'm fighting to make wifi work on an HP dv6-3194.

The symptom is that I'm always asked to enter the WPA passwd.

1-This is a fresh FC15 install:

Linux localhost.localdomain 2.6.38.6-26.rc1.fc15.i686.PAE #1 SMP Mon May 9 20:36:50 UTC 2011 i686 i686 i386 GNU/Linux

2- Network interfaces are detected:

3- pci card is RT3090

4- lsusb returns:

5- lsmod returns:

6- iwlist wlan0 scanning detects wifi networks without problems.

7- relevant dmesg entries:

8- wpa_supplicant.log

I've tried many suggestions from this forum about RT3090 or RT2800, but none worked :-(none seemed to be close to my problem:

Most of them relates to interface not seen, wifi networks not detected, system freeze.

View 6 Replies View Related

Networking :: Unable To Start The Configuration Form The System->admnistrator?

Dec 9, 2010

hi everybody i am using red hat linux 5.0 & i unable to start the network configuration form the system->admnistrator->netowrk actually by running system-config-network cmd i am able to edit only gateway but not the primary dns

i also tried from the /etc/resolv.conf. by editing the resolv.conf & after restarting the netowork the resolv.conf remove the chages & it become as like previous. actually there is some problems with the starting services form the panel->system->administration->serversettings->services some of the services are stopped can anybody tell me which are that services for system-config-network

View 2 Replies View Related

CentOS 5 Networking :: Unable To Start Eth1 From The Command Line?

May 28, 2009

I am trying to attach my server to 2 diferent networks, with fixed ip addresses,
eth0 = 192.168.0.2 255.255.255.0 with gateway 192.168.0.1. This is currently working, and I can ssh o the machine on this address

eth1 = 192.168.150.5 255.255.255.0 with gateway 192.168.150.1

When I try and start eth1 with ifconfig eth1 up, I get the error message "eth1: unknown interface: no such device"

I have configured eth1 using system-config-network-tui and /etc/sysconfig/networking/devices/ifcfg-eth1 looks correct

GATEWAY=192.168.150.1
TYPE=Ethernet
DEVICE=eth1
BOOTPROTO=none

[Code].....

View 2 Replies View Related

OpenSUSE Install :: Booting With Bootsplash Turned Off / Sending Error FATAL: Module Ata_piix Not Found?

Dec 20, 2009

while booting with bootsplash turned off there's a message "FATAL: Module ata_piix not found FATAL: Error running install command for ata_piix" .Though everything works fine i'd like to know what does this message mean and is there a way to disable loading of ata_piix whatever it means.

View 2 Replies View Related

Fedora Installation :: Getting Zonet ZEW1642D On 14?

Mar 9, 2011

I finally jumped on Fedora, having been on Windows then recently on OSX. Anyway, I wanted to run a desktop dedicated to Fedora but my setup is far from the router. This meant that I had to buy a wifi card and I chose Zonet ZEW1642D. To my disappointment it's not even being detected.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved