I upgraded from F14 to F15 using the DVD. The network worked fine after the upgrade.This morning I updated to the latest RPMs and rebooted, and now the network donot work!ifconfig shows only the lo interface. NetworkManager does not start, /var/log/messages shows signal 11.I tried to boot with the original kernel, but the results are the same.
View 6 Replies
I just updated my Fedora 10 installation with the latest NetworkManager (NetworkManager-0.7.0.99-4.git20090324.fc10.i386) and now my NetworkManager fails to start. The output in the /var/log/messages is
[code]...
As I reported in this bug:[URL].. root is not able to start an openvpn-connection via the "nmcli"-command to control NetworkManager, whereas my user does not run in any problems with this command. My error output when starting as root is as follows:
Code:
# nmcli con up id "my-openvpn"
Active connection state: unknown
Active connection path: /org/freedesktop/NetworkManager/ActiveConnection/5
state: VPN connecting (need authentication) (2)
Error: Connection activation failed: no valid VPN secrets.
Does anybody know what to do about this strange behaviour? The vpn-secret seems to be stored in the gnome-keyring and in the /etc/NetworkManager/system-connections/my-openvpn simultaneously. But root cannot access any of these. Why this is important? I'm trying to set up a dispatcher-script to automatically start openvpn on eth-connection. but this does throw the exact error from above (no valid vpn secrets..).
[Code]...
I've been running CentOS on my laptop for a few weeks now. I don't know what happened today, but when I boot up, the NetworkManager wont show up on the panel, and I don't have access to wireless networks or Internet. I tried booting my Windows partition and the wireless works fine. I can't seem to remember any latest change I've made aside from the wallpaper =) Any ideas where I should start debugging? I could see the module "iwl3945" still loaded. Here's a manual type of my lsmod | grep iwl3945
iwl3945 90177 0
mac80211 137929 1 iwl3945
cfg80211 30793 2 iwl3945,mac80211
After upgrading to Lucid said adapter is nonfunctional - NetworkManager won't start on booting (I'm using 2870sta module) and it finds no networks - neither does WICD. The device itself is identified: "lsusb" gives a line "Bus 001 Device 005: ID 148f:3070 Ralink Technology Corp." "iwconfig" gives nothing under lo and eth0 and this under wlan0:
Code:
RTxx70 Wireless ESSID:""
Mode:Auto Frequency=2.412GHz
Link Quality=10/100 Signal level:0 dbBm Noise level:-143 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
And a "lsmod | grep -e rt2 -e rt3" gives:
Code:
rt2870sta 525366 0
(Note: I had a similar problem going from Jaunty to Karmic, but blacklisting rt2800usb in my blacklist.conf fixed it. No such luck this time.)Using a Zonet ZEW2500P.x86-64 Lucid.
"checking for applications currently in use" before updating packages is taking too much time! ( around 20 min till now ) ... what might be the reason
View 11 Replies View RelatedI installed some updates this morning to my F14-64 system. Both Thunderbird and Thunderbird-lightning were updated. Now, Thunderbird won't start at all. The process is running, but no window ever appears.The only thing I've tried at this point is running 'thunderbird -safe-mode' from the command line to disable all plugins, but the result is the same as just running 'thunderbird' -- it just hangs. It doesn't *appear* to be a plugin problem
View 14 Replies View RelatedI've some problems upgrading to version 10 from version 8. My workstation is certified by RedHat. It's a HP xw6600 with double processor Intel Xeon 5405 2.00 12M/133 QC and graphic card for dual screen Nvidia Quadro NVS 290 PCle. In my OS library I found version 8 to install. It has been installed successfully! However; I've read about advantages for workstation on version 10. Thus, I've downloaded Fedora ISO ver.10 and I've tried to install it in my WS. Here I found a problem: Just in the moment it try to start anaconda, the screen remain black. After three failed intents, I have tried to upgrade my version through the 'yum':
# yum -y update
# yum install preupgrade
# preupgrade
It ran perfectly till anaconda try to run again. Then, I've tried to upgrade to ver.9 from ver.8 and I getting the same problem. I've downloaded the Live CD and that is blocked as well. Of course, I've installed all drivers of my WS before upgrade but I get the same problem. So... How I can fix this problem?... I really need move to version 10. Ah!... I've tried to install beta version 11 but after one hour I get a error messages due at a bug
I have no problems seeing the networks available and connecting to a network in KDE. But there is no network manager in GNOME. I might have messed up with the settings earlier. What I can do though is run knetwork manager every time I start up (or add it to start up programs). But that opens up the KDE wallet which would rather avoid.I am thinking I need to install something related to NetowrkManager.
View 2 Replies View Relatedif the NetworkManager uses wpa_supplicant? I normally dont use NetworkManager and decided to try it. I started it and tried it out and it works with WEP and WPA! I cant figure out why using the iwconfig command is not working by itself for WEP. WPA working with NetworkManager is just a bonus though.
View 4 Replies View RelatedI'm an inordinate amount of trouble getting F15 to run without NetworkManager. If I boot with the NetworkManager service enabled, my NIC presents as expected at /dev/eth0 (I'm using biosdevname=0). However, when I stop the NetworkManager service, /dev/eth0 disappears from the filesystem.If I boot without NetworkManager enabled, /dev/eth0 is never created. Reviewing dmesg, udev is loading an ethernet driver.
View 1 Replies View RelatedI loaded F10 up on my laptop a few nights back. NetworkManager connects via Ethernet just fine. It will also connect wirelessly, but only when security is disabled. I've been using 128-bit WEP.
When I try to connect using security, this is what appears in the log:
Code:
Jan 29 21:07:17 localhost NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Jan 29 21:07:17 localhost NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
[Code]......
after fiddling around with compiz-fusion and KDE, my network suddenly disappeared. I looked in the package manager and apparently I don't have the gnome applet for networkmanager...but everything else I seem to have (the git version not svc or w/e) Anyone know if installing the applet will let me choose my wireless network and connect to it? Right now I think so, but what I have to do is boot into windows, find the package on the web and download it, then boot into fedora and install it
where I can find the fedora 10 networkmanager-gnome package (git version for x86_64)? I looked around and found the svc version and a git version for i386, but my OS is x86_64 and I couldn't find any git versions of it for 64-bit fedora's. btw, I have no idea what git and svc mean, but when I tried to install the svc version, it told me I had to install svc versions for all the other networkmanager packages...
I recently installed F10 x86_64 on my Lenovo T61 laptop, and while I'm quite pleased with F10, I am having a difficult time with my wireless card. I spent most of yesterday searching for a solution, but none have presented themselves. Scenario: I am trying to connect to a HIDDEN SSID with NO ENCRYPTION (work Wifi, don't ask) using network-manager and its associated applet.
Symptoms: I left-click on NetworkManager, select "Connect to Hidden Wireless Network", enter my information, NetworkManager does a few things, and finally I'm told that NetworkManager cannot connect to my network.
[Code]...
I have just installed Fedora 10 on an old laptop and was quite impressed with how smoothly it all went ... until it came to setting up networking!
I have battled for three days now and I'm almost there;
- installed updated firmware to the built in Broadcom 4306 wireless network adapter
- got NetworkManager to work with a static ip address by manually editing the ifcfg-wlan0 file
- managed to get the WPA security to work
The only problem I am left with is that there is no default route; if I set one up using: ip r a default via 10.1.1.1 dev wlan0
Then everything starts working.
If I try to add routes using the NetworkManager gui interface they dont get saved (no suprises there then! ).
I have tried creating a route-wlan0 file in /etc/sysconfig/network-scripts/ but this seems to be ignored by NetworkManager.
Since the NetworkManager GUI is almost useless, does anyone know if there are any other configuration files I can manually modify to get a default route set?
Just upgraded from Fedora 10 to 11 and cannot setup wireless connection via NetworkManager. By some reason it doesn't store WPA key. There are following errors in the message log:
Code:
Aug 14 14:37:05 mike-dev NetworkManager: <WARN> connection_get_settings_cb(): connection_get_settings_cb: Invalid connection: 'NMSettingConnection' / 'uuid' invalid: 1
Aug 14 14:37:11 mike-dev NetworkManager: <WARN> wait_for_connection_expired(): Connection (2) /org/freedesktop/NetworkManagerSettings/2 failed to activate (timeout): (0) Connection was not provided by any settings service
Fedora 13 64. NetworkManager tries to unlink /etc/hosts and is blocked:
Code:
SELinux is preventing /usr/sbin/NetworkManager from unlink access on the file /etc/hosts.
Additional Information:
[code]....
i'm trying to replace default F15 NetworkManager with wicd. i installed wicd and used "chkconfig NetworkManager off" to disable NM but the problem i'm getting is
1. after each reboot i have to start wicd manually from su. any solution to get it loaded automatically?
2. also as i stopped nm, i have no network shortcut in taskbar, anyway wicd icon can be integrated in taskbar?
downgrading PPP, NetworkManger, and NetworkManager-gnome. This worked but is there an easy way to know when it is safe to apply the updates that are available?
View 2 Replies View RelatedKinda fed up with NetworkManager. Since trying the betas of F11 on my laptop, i've had endless bad experience with it.
Installed version: 0.7.1
Aside from the description below, please let me know what detailed system info you want to see (specific commands appreciated).
When i log in, the applet loads. However, it doesn't connect to the last Wifi connection i used. My SSID is hidden, so i click on the applet and choose "Connect to hidden wireless network". i see my stored connection in the drop-list. i select it, and all fields are greyed out, the WPA key is blank, and the Connect button is disabled.
Leaving that dialog, i delete my stored connection and re-create it manually, setting all the information correctly. i have DSL, using my DSL modem in bridging mode, and for some reason NetworkManager doesn't retrieve the DNS entries from the modem, whereas Windows does. So i have to set the connection to "DHCP (Address Only)" and manually add the IPs for my DNS.
However, the connection doesn't initiate, so i click the applet again and attempt again to connect to my hidden SSID, using the newly created profile. Same problem: no WPA key, all boxed disabled, and Connect also disabled.
The ONLY way i can get this thing to connect is by deleting my stored connection, clicking to connect to a hidden SSID, and create the connection from the New dialog. However, then i still have to go into Edit Connections and set the DHCP and DNS correcly before i can reach outside.
This is ridiculous, and i haven't been messing with any other configuration. i had a thread when F11 was still in beta where i had inconsistent results with NetworkManager. After thinking i got it fixed with some help, and discovering it wasn't, i decided to wait for the final release to see if it would work any better.
(automatically connect to the last active connection), consistently (connects when it loads at login every time), Otherwise, if there's a different connection manager, i'm open to that as well. Especially if the alternate connection manager can automatically retrieve DNS settings the way Windows can.
I have a typical 'linksys' style home wireless router (whose IP is 192.168.0.1) .
If I use DHCP, everything works fine:
Code:
However, if I try to give myself a static IP,
Code:
(I also never understood why the DNS server should not be the real dns server address (some external ip) rather than the router's address? but that is what gets set automatically when using DHCP)
So using manual, it connects, but then the internet doesn't work. The only difference I see when I go to "connection information" when connected with dhcp vs manual is in dhcp mode there is a "default route: 192.168.0.1". Is that the problem? How do I set this "default route" / what is it?
I'm looking for some information on setting up a VPN client through Networkmanager in Gnome. My company uses a Sonicwall VPN server, and I'm having trouble getting my F11 laptop to connect. I've tried OpenS/WAN with no luck, and stumbled across Networkmanager's VPN setup. I can choose Cisco Compatible VPN (vpnc) which says it's compatible with Sonicwall IPSec-based VPNs. Is there a how-to I can check out, or has someone else got this setup to work?
View 2 Replies View RelatedI thought configuring a vpn would be a piece of cake, but it seems I'm missing something.
I'm attempting to create a vpn (pptp) using the networkmanager (0.7.1). I enter the gateway (I assume thats the server I'm trying to connect to) and my login information. What is the NT Domain?
When I try to connect it only tells me after a while that it failed to do so. How can I find the information on what went wrong in the process?
I'm having trouble getting this wireless card to work. I installed the broadcom-wl driver on Fedora 12.
Code:
[xxx@localhost ~]$ uname -r
2.6.31.6-145.fc12.x86_64
[xxx@localhost ~]$ lsmod | grep wl
wl 1278432 0
lib80211 6436 2 lib80211_crypt_tkip,wl
The card is recognized by System--admin--network as the correct card (BCM43XG) and assigned eth1. However, NetworkManager shows no wireless network. I have a great signal on the same machine if I boot into a Windows partition.
I'm so sorry to bother people, but I'm totally at a loss.I've searched the forum and have not found the answer.My NetworkManager icon is missing from the notification bar. Ive tried rt clicking on the top panel >add to pannel>notification area....yet it is still missing.I know that NetworkManager is installed, yet I cant even access it to connect to a wireless network. I'm able to connect to Eth0.I cant tell if my wireless card drivers are setup or not and if that makes a difference.
View 4 Replies View RelatedI have just installed Fedora 13 on my Lenovo Ideapad S12 (company laptop, evaluating Fedora for companywide use on all laptops) and a facing a weird problem with KDE4 and NetworkManager / knetworkmanager. The laptops wifi card is a Broadcom BCM4312 and I have successfully extracted the necessary b43 firmware. The b43 module loads on boot and the wireless card is activated and ready to use. However, NetworkManager doesn't seem to agree and has wireless disabled by default every time I reboot or even logout / login. I have to check the box manually after which it automatically connects to my wifi network at home.
Any idea where I can check that box automatically on boot?
I'm on F14 and can't seem to get NetworkManager to behave. I seem to remember being able to start my machine and see my static address configured right after boot. For some reason, that's no longer the case. When I finish a boot, I'm not getting any address until I log in. I've tried editing the ifcfg-eth0 both by hand and by the system-config-network. I've played with the "Available to all users" checkbox on both the nm config applet as well as the system-config-network gui. I can't seem to get it to behave predictably and give me my static without having to be in a gnome session.
Here's my ifcfg-eth0 from /etc/sysconfig/network-scripts
I'm using Fedora 15 with KDE, and in the NetworkManager settings I can't set my Ethernet connection to be a System Connection. The box is greyed out. I assume only root can enable this option, but GUI apps typically ask for an administrator password. I did add my user to the "Administrator" group when I installed and I can use sudo and all that.
View 2 Replies View Relatedhow nobody else could have run into this in the meantime. [URL] Two friends of mine are having the same issue on Ubuntu-11.4-machines. In short: Connecting to the Cisco-VPN via shell-command "vpnc" works flawlessly, whereas NetworkManager just doesn't connect at all. We had this working in older versions of Fedora/Ubuntu about some months ago...
View 9 Replies View RelatedI seem to have somehow messed up my repositories and now NetworkManager isn't working.
I have two errors happening, which I'm sure are related. First of all, when I try to load knetworkmanager, I get the error:
Code:
knetworkmanager: error while loading shared libraries: libkminterminals.so.4: cannot open shared object file: No such file or directory Second of all, when I restart my computer, upon loading I get a message from Akondi Server Self-Test saying several databases failed. I've never seen this before, so I think fixing these errors would be best? Some of the errors are MySql failed, akondi not registered at dbus, etc.
Lastly, I don't have a wired connection so currently my machine has no internet. I'm using a second laptop to get necessary files and I transfer them with usb.
