I used the information on this page...
wiki.archlinux.org/index.php/ZTE_MF626_/_MF636
...to be able to configure the usb modem in my linux computer. As I've been using Linux there onwards, I didn't mind any longer.
Now I plugged the usb into a windows computer but the driver installation routine doesn't start. It's obvious that's because I deactivated the cd mode. How do I bring it back?
How would I configure my box to connect to a modem in bridge mode?
I have a server at home that im migrating over to be the default-gateway/router. I have everything else setup (dns,dhcp etc) now just need the ppoe part, or so i beleive?
I have two interfaces. eth0 (lan) and eth1 ready to connect to the modem.
The modem is in bridge mode ready to go.
What is my next step? Are there any good guides, I didn't find any.
Pl can anyone guide me to connect centos 5.5 using ethernet port to ADSL Broadband modem which is configured in PPPoe mode?
View 19 Replies View Relatedfind and install modem driver for the Alcatel X200 USB modem?
I've been all over the internet trying to locate Linux drivers but no success. Alcatel's website says is not supported, only in Windows. I'm sure there's gotta be a way to use the X200 in Linux.
i'm running Kubuntu karmic and i've been using a 3G Huawei E1552 modem to connect to the internet, everything was going well when suddenly my modem stopped working. I've tried reconfiguring everything, i even reinstalled kubuntu from scratch with no success.Here's a part of my /var/log/debug
HTML Code:
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099883] usb-storage: device found at 7
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099888] usb-storage: waiting for device to
[code].....
I have (had) a dual boot system of Ubuntu (11.04) and Windows 7. I was forced to reinstall Windows over itself and it installed its boot loader. How do I get my Grub boot loader back? I googled it and found instructions, but they were from 2007 so I thought it might only be for Grub Legacy. The instructions were as follows:
Boot from a live cd
run "sudo grub" in a terminal
then, "root (hd0,0)", "setup (hd0)", and "exit"
reboot and grub should be present
While I wait for ubuntu to download so I can create a live cd, can someone confirm if this is correct for Grub 2? Also, what commands will tell me which hard drive and partition I need to put in the above commands (hd0,0)? I have (4) internal hard drives and boot drive has a few partitions on it.
When I installed Fedora 12, Autoten gave me the option to automatically log me in. Well now, I want to go back to using a password to activate my desktop. I've searched but I haven't found any information on how to do this.
View 2 Replies View RelatedI need to manager printers from shell. The version is Centos 5.4. At this moment i cannot manager printers, and somebody told me that i need to reinstall centos. Is it possible to do anything to reactivate that property, without reinstalation?
View 12 Replies View Relateda perl script that becomes active when the machine goes inactive (!) and executes an rtcwake command designed to spur the computer into action at a designated time so that cron tasks are performed. The script, which is given below and which originated at a Ubuntu forum, is not working, and so I am trying to understand it. Not being familiar with perl, I'm stuck at the line containing the test if(m/^s+boolean true/){ ...
Code:
#!/usr/bin/perl
my $cmd = "dbus-monitor --session "type='signal',interface='org.gnome.ScreenSaver', member='SessionIdleChanged'"";
while (<IN>) {
if (m/^s+boolean true/) {
[code].....
I ordered this USB 802.11n dongle for about $10 and am having problems.I found a firmware related bug (Bug #595455) that keeps it from working out of the box and got around that. I put the right firmware file in the right place and CAN CONNECT TO B or G Access Points.hen I put my AP in N-Only mode, I can see the network, but cannot associate. With the AP in mixed mode I can Associate using G.The most interesting thing I found was something that had very
few google hits (like 4). In the dmesg output after associating I see the message:
Successfully associated, ht not enabled(0, 1)The most interesting thing about this is the (0, 1) at the end.I don't know what that means but it seems like a clue as to what the problem is.This device uses the realtek chipset 8191S, there are conflicting reports on this, but all the reported possibilities seem to use the same driver from realtek (rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.2010 0625).Here is some random info:
Dmesg output:
[85082.620027] usb 1-3: new high speed USB device using ehci_hcd and address 6
[85082.754586] usb 1-3: configuration #1 chosen from 1 choice
[85082.755456] ==>ep_num:4, in_ep_num:1, out_ep_num:3[code]........
Below is a print out of my partition Table from Fdisk, in Cylinder mode, Sector mode, and then in expert mode?
Why in expert mode does it look like Partitions 2 and 3 share the same sector / hd / Cylinders? Is this OK?
Code:
I just got connected to Charter Cable Internet service a few days ago and I'm having a weird problem with my home network. Prior to this my network worked fine. On my network I have a desktop running Ubuntu 9.10/64 and Virtualbox with WinXP installed, an HTPC with Ubuntu 9.10/32 installed and a laptop dual booted with Ubuntu 9.10/32 and WinXP. The desktop and HTPC are hard wired to a wireless router and the laptop is wireless. The cable modem is hard wired to the router. I have samba installed and UFW is disabled. The problem is: with the cable modem turned off or on standby, all machines connect to each other and can transfer files, etc just fine but when I activate the cable modem all of the machines can connect to the Internet but the machines running Ubuntu can't connect to each other on the home network. If I boot the laptop into Windows, it can connect to the Linux machines just fine but if I boot it into Linux, it won't connect to the Linux machines but it can connect to the Internet and as far as the desktop, Ubuntu won't connect to the network but Windows running in the Virtualbox with bridged networking can connect to all of the machines.
View 2 Replies View RelatedI'm try to create a mobile broadband connection using my Huawei E 1550 medem. but in Network manager there is not way to select my modem in the first step ( device selection step ) the drop down menu is locked. what to do ? how to configure my modem with ubuntu ?
View 1 Replies View Relatedwith installing Modem Huawei E170. my modem can not connected and suddenly remove from my PC. i am using Ubuntu LTS 10.04.
View 1 Replies View RelatedMy modem is modem SU-6200 cdma 1xEVDO cannot detect. I need driver, but I cannot online in ubuntu 9.10. Check my modem at [URL].
View 2 Replies View RelatedI have a dual boot Win XP and Ubuntu 8.04. I use my phone Nokia 7210 Supernova as a USB modem on XP using NokiaPC Suite. I don't know how to do this in Ubuntu.
View 1 Replies View RelatedI'm using an external Huawei CDMA fixed wireless terminal (phone + dial-up modem). It connects to my PC via a USB port. Actually my PC recognizes it (after driver installation) as "TIUMP Serial Port". I guess the driver is a kind of USB adapter for a serial port.
I can't get it to work in ubuntu 9.10. I ran wvdial (after installing dependencies and wvdial package) and it doesn't recognize my device as a modem. Is there any solution to this problem? Without solving it, I won't be able to go online from ubuntu.
I'm running Ubuntu 9.10 (Kubuntu) and have a LG Arena (KM900) smartphone which when plugged into the USB socket and I select the iSync option on the phone, the handset is correctly identified as a Mobile Broadband device in Ubuntu network manager. However, I'm having difficulty getting Ubuntu to connect to T-Mobile through the 3G modem. I've referenced [URL] and[URL] and I can not connect. I'm assuming that this is something to do with Mobile Broadband settings I'm using:
APN: general.t-mobile.uk
Username: user
Password: pass
I have a WiFi modem. Its Chinese(non-brand) modem. I can use this modem in windows Xp easily. Just need to install a software given with this modem. but cann't use it in Linux as using ubuntu 9.10 below is my lsusb report.
Quote:
ubuntu@ubuntu:~$ lsusb
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[Code]....
I moved from Debian to Ubuntu a few months ago, with everything working fine, except my 3G modem (which worked with wvdial and umtsmon in Debian).
The packaging claims that it is a Huawei E160, but lsusb says different: E220 (12d1:1003).
I've followed various instructions from these forums and the wiki, and it seems to be being recognised as a modem (I can set up an O2 prepaid (UK) connection), but it refuses to connect.
i m able to change mode to usb modem device 9603 Micromax 300 G USB modem.
but still got stuck with
bharat@ubuntu:~$ sudo modprobe usbserial vendor=0x1c9e product=09603
FATAL: Error inserting usbserial (/lib/modules/2.6.31-14-generic/kernel/drivers/usb/serial/usbserial.ko): Invalid argument
how to run my telstra next g usb modem in ubuntu 10.4?
View 4 Replies View RelatedI have a USB modem working in windows. But no luck to connect using Ubuntu 10.04.
I have setup usb-modeswitch and other stuff. The modem is attached to port ttyUSB0. But when i run "sudo wvdialconf" it displays message like this.
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
Modem Port Scan<*1>: S0 S1 S2 S3
WvModem<*1>: Cannot get information for serial port.
ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Sorry, no modem was detected! Is it in use by another program? Did you configure it properly with setserial?
read the FAQ at [URL]
If you still have problems, send mail to <wvdial-list@lists.nit.ca>.
organize networking with usb 3g modem in my Ubuntu Server 10.04. Or give me any links how to do it.
View 1 Replies View RelatedI am running Ubuntu 11.04 on an external USB drive on a Dell D630 laptop.
My issue is I can't get my 3G modem to work. It is a K3770 Huawei modem.
When I plug it in after boot up it is not recognized at all as far as I can tell. (Which is not very far).
When I plug it in before boot up it shows up as a CD rom drive. I have usb-modeswitch is installed. (It was installed by default during the 11.04 installation.)
what to do to get this to work? Remember my Ubuntu is running on an external USB drive so anything that switches USB off even temporarily won't work. (I don't think).
I've just spent 2 days of extensive lurking how to solve this problem. Namely, i have ZTE usb modem, model MF626 T. The sofware provided with it works only under windows. What i tried first was to download hso.ko module (copied to the /lib/modules/`uname r`/kernel/drivers/usb/serial/). Then i downloaded hsolinkcontrol and HSOconnect. Unfortunately, i didn't get those /dev/ttyHS* ports that should appear. Only /dev/ttyUSB*. I blacklisted option module. Then changed occurences of ttyHS* to ttyUSB* in .py sources for HSOconnect. what i get is the popup interface GUI that has "connect" button disabled. Then i tried to set up connection via gnome-ppp. The usb modem was automatically detected as /dev/ttyUSB1. But when i supply telephone number that i got with the stick, i get message after "Sending: ATM1L3DT*99*" ->"no carrier found". Then i tried to copy the other two modules i found on the net-airprime.ko and usbserial.ko. I've renamed the option.ko and old usbserial.ko in order to use them later if needed. And also i've put in /etc/udev/rules.d/
some scripts i've found on net, used to mount and unmount ZTE modem. None of all that worked, and somehow i have the feeling i've messed up everything. What i just posted above is the sum of everything i googled out. I would be very glad if someone would help me out with this. I usually like to spend some time lurking and googling, but this is simply taking too much time...
I am trying to set up one home networking lab in which I plan to use three routers. One of the router will be QUAGGA over Ubuntu Server. I cannot figure out how to setup my HSIA USB Modem (TataPhoton+ from Tata teleservices)in ubuntu server. This device works fine with Ubuntu 9.10 desktop edition. Just a few clicks in network manager does the job, but how to achive the same in ubuntu server which have no GUI
View 1 Replies View RelatedSteps for using scan Modem to Identfy dial up modem?
View 1 Replies View RelatedI have this USB modem P300U(SIM600 chip based) which works fine under wind@ws because it has it's own driver, but the clever seller told me that it worked under Linux as well. It was with Redhat 8 but I couldn't get redhat 8 to download. And until now absolutely false.
I have Debian with Kernel 2.6.32-5-686 I just want to send sms through this modem. It's not recognized as modem I'm frustrated because it's not useful for me if it doesn't work on Linux I looked for info but I can't make it work. What I get in my debian is:
lsusb: Bus 002 Device 003: ID 10c4:ea60 Cygnal Integrated Products, Inc. CP210x Composite Device
dmesg: 9857.011649] usb 2-1: new full speed USB device using uhci_hcd and address 3
[ 9857.818942] usb 2-1: New USB device found, idVendor=10c4, idProduct=ea60
[ 9857.818989] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[code]....
I use ubuntu 9.10 and PCI connected Conexant CX11252 Modem. My GNOME PPP doesn't detects my modem. How can I create a connection? Is there any way to detect my modem and connect ? or ubuntu is fit only for broadband? I think most of the activities in ubuntu depends on internet. I can't do any work. I am losing my money in Internet Cafe. Broadband is even not available in my resident area. Therefore. find a solution to connect internet via my dial up modem!
View 9 Replies View Related