I would like to configure the eth0 manually. I can configure the ip address and sub-netmask but the system can't hold my gateway ip address (I added). It will keep it 0.0.0.0. I have no problem when I getting IP address from DHCP server.
View 1 Replies
I'm running Ubuntu 10.04 and my setup is as follows:
As you can see, I am directly connected to router 192.168.25.1, and so my ip address is 192.168.25.101. I want my ip address to be 192.168.13.101, and make router 192.168.13.1 my gateway router. Is this possible under the current physical layout (I do not want to have to connect directly into 192.168.13.1, but keep my computer where it is at)?
When I run tracepath, it shows 192.168.13.1 is one hop away.
What I've tried:
The problem is under this manual setup, I cannot ping 192.168.13.1 and running command netstat -rn returns the following:
I have trouble getting a gateway to the internet when setting eth0 with a fixed IP address. The gateway address (192.168.2.1 my modem/router) resets to 0.0.0.0 whenever I apply the changes. DHCP works fine but I need a fixed address for my server.
View 6 Replies View Related5.10 Breezy configured as machine controller. Works great eth0 is a fixed IP to communicate with controller comms board. Not easy at all to alter - the comms board is hard coded to listen on eth0 for commands.
I can use eth1 as the default gateway and ping google.com, etc. But when I now attempt to communicate with the controller with netcat, e.g.
Code: echo !HH | nc 192.168.1.6 80
I obviously never get an answer since the request is passed via eth1. Using the -g option with netcat doesn't work either. I had a look at iptables but it doesn't seem to be able to do what I want. How I can still use eth0 as my communication port to the controller whilst eth1 is the default gateway?
Since I have a new internetaccount, 2 days ago, I have a problem on my server [Fedora Core 8]. I use it as a router.
eth0 is for the internet.
eth1 is for my LAN.
But since my new internetaccount my server uses eth1 for the internet. This is a line from my syslog:
Code:
NetworkManager: <info> Policy set 'System eth1' (eth1) as default for routing and DNS. I killed the NetworkManager daemon and now it works but this must not be the way to do it? Where do I tell my server that I use eth0 for routing and DNS?
i install kernel rpm after i boot that kernel network not working kernel name : kernel-rt-trace-2.6.24.7-132.el5.centos.i686 [URL] error "Bringing up interface eth0: Device eth0 has different MAC address than expected, ignoring."
View 1 Replies View RelatedI have a laptop running OpenSuSE 11.2. I use the Yast menu to set up network settings via "traditional" ifconfig setup (not NetworkManager), because I found NM unusable in prior releases when doing network gymnastics such as router re-flashing, LAN reconfiguration, etc. where I needed control of the IP address, netmask, DHCP, tftp, etc. My laptop works fine with Yast "traditional" ifconfig configuration for eth0 connected to router to Internet. Works fine with Yast ifconfig configuration for USB WiFi as wlan1 to WiFi router to Internet. Also works fine for virtual machines on vmnets NAT-ed to the Internet. Works fine as long as there is only one network connection, that is.
Now, I have a second laptop. I want to network laptop #2 eth0 to laptop #1 eth0 for file transfer and/or Internet access WHILE laptop #1 is is linked to the Internet through wlan1. Unfortunately, I have not figured out how to get Yast/Network Configuration to do that. I have not been able to get Yast/Network Configuration to see both wlan1 and eth0 at the same time--when the Yast utility finishes, I do >ifconfig and >route, and I find that I have lost either eth0 or wlan1. Thus, when I do direct-connect file transfers, I loose the WiFi Internet connection on both machines.
I suspect that it might have something to do with Yast/Network Configuration utility not being able to handle two network interfaces on the host with different IP addresses. how to properly put an OpenSuSE machine on two networks simultaneously? And then how to turn on IP forwarding so that I can use laptop #1's WiFi as an Internet gateway for laptop #2?
I have a requirement of switch between wireless network with a single wireless device. First it should be switched to adhoc mode and then after sometime switch to infrastructure mode to establish internet connection. Everything works fine except the gateway settings.
I have used:
system("route add default gw x.x.x.x dev wlan0") to set the gateway, where x.x.x.x is gatewayip address.
I have used this whenever switching happens in addition to ifconfig command to set the ip address and netmask. But this is not setting the gateway ip address. How to set gateway IP address?
System details below
OS :CentoS 5.3
Kernel :2.6.18
OS:Fedora core 6
I have just changed my gateway address,now I can access internet with my browser but unable to run add/remove software as it says no network connection available,system updates are not working as well. What should I do make these working?
Im trying to achieve the multiple uplinks/provider found on LARTC.org. I have to get the IP addresses from my interfaces (EF1 and EF2) by using a script, but i dont know where to look at for the default gateway from each interface which got their ip address from my ISP.
View 1 Replies View Relatedwhen I do "route -n", I got:
Code:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo
0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0
I need to change the static configuration, like I 169.254.0.0, I don't know how it got there also I want to delete 192.168.1.1 from a static gateway. How can I do this?
Since my upgrade to 10.04 I can't use my eth0 wired connection.The wireless works fine.I have tried auto eth0 in network connections set to manual and dhcp. eth0 shows up in ifconfig but no address is assigned.
View 1 Replies View RelatedThe IP address I want for the gateway computer is 192.168.1.100 As I have 'sharing' enabled in Network manager, there is no provision there to specify the IP address for eth0. That is, cannot manually set it there. Every time I boot up, the IP address changes to
[Code]...
I downloaded Fedora 10 32bit and put it on a Dell Dimension 8200 to save it from the recycle bin. Everything seems to work except I cannot get an IP addr. Roadrunner is my ISP using a cable modem and a Linksys Instant Broadband Series Etherfast Cable/DSL router model BEFSR41. In system-config-network, the nic shows inactive. If I activate it a window opens saying "determining IP information for eth0". After a short time the message adds the word "failed". Using a Windows PC on the same network, I can look at the DHCP connections on the Linksys and I see the MAC addr for the PC running Fedora.
From the OS installation, /etc/sysconfig/networking/devices/ifcfg-eth0 has following:
DEVICE=eth0
HWADDR=00:80:ad:d1:88:c9
ONBOOT=yes
[Code]....
i know exactly what i need to do, im just not familiar enough with command line to do it properly.i have 7 computers.the first 4 are connected to a router via wireless at one end of the house. of the last 3 only 1 will be able to access the router via wireless, so it needs to share it's one wireless connection via ethernet. this computer i'm going to call 'server'server will have two IP'swlan0 192.168.1.6 this connects to the router that has internet access.eth0 i intend to have the following settingsip:192.168.0.1sub: 255.255.0eth0 will connect to a second router, where the cat5 cable goes from the server, into the internet port of the router where i will define the router's static IP:IP: 192.168.0.100sub: 255.255.255.0gateway 192.168.0.1i have then set the router IP for LAN handling as 192.168.27.1 and all ethernet connections will have a 192.168.27.x IP.
so i need to know how to, without a gui application, use the terminal to assign server eth0 a proper IP address, and tell the server to take the connection it has and share it through eth0 to supply internet for the last 2 computers via ethernet.i had it set up in this way with a windows machine being the one that had the wifi access, but i'd rather have it setup for the ubuntu server to do this task. security is imperative for these 3 remaining machines, so just getting 2 more wifi adapters for a connection to the initial router isn't an option.the 2 that connect to server do so through SSH and though server IS connected via wireless it only makes outward connections through
I have 4 servers that I got at auction and they now have ubuntu running with gnome interface.I installed apache2 and tried to edit the conf file but i am not sure if it is a router issue a dns or the config.I am trying to figure out how to set the server to hold the domain from a dynamic ip address and also how to create some test page to see if i can acess from the internet.
I have purchased some books on the command lines and how ubuntu works, I am understanding it so far, but dont know how to have a directory for the dns request to point to for the sitewhat i want to do with the servers...voipeb server for about 4 websites - one is for a volunteer rescue organization, another for a test auction site and 2 portfolio sitesremote file access- if possiblealso on a side note, is it possible to have a message relay from one cell phone or transmit to the server and have it send sms message to cell phones? - this will be used for the rescue group as well.
I am trying to get networking up on an old PII which I have successfully installed with FC4. There is a link and activity on the onboard interface because I see the indicator lights. The controller is a 3Com PCI 3c905 Boomerang 100baseTx @ 0xdc80.The only message returned by dmesg about eth0 is "Dropping NETIF_F_SG since no checksum feature."The driver module, 3c59x, is loaded as well as the mii module that depends on it.There is something about "unknown parameter`irq'" in the dmesg text regarding the driver.I noticed that eth0 is sharing an IRQ with the UHCI Host Controller.That should not be a problem, but it should not be necessary. And I could do away with USB if this is a conflict and that is the easiest way to solve it.When I drop to console at runlevel 3, and call dhclient, which is installed, I get a message telling me there is no reply to the dhcp request.I don't think the problem is on the router/switch side.
View 5 Replies View RelatedNew to CentOS5.5 I'm experiencing some trouble in order to continue my configuration. I've just installed my vmware tools and configured my network card with system-config-network
Edit eth0 (eth0) - vmxnet3 -> with a static IP I rebooted my server and since then I lost my eth0. I still see it in system-config-network, but I can't active it anymore.:
/etc/init.d/network start Bringing up interface eth0: Device eth0 has different MAC address than expected, ignoring. [FAILED]
Everything worked fine until very recently, and without apparently ANY change to the settings on the server, a secondary IP that was assigned to my server won't work anymore..Any IP attached to the same server works fine.. So in my case, the problematic IP is 213.8.155.67. The other IP (213.8.155.42) works without any problem.How would I go about troubleshooting this?
ifconfig:
eth0 Link encap:Ethernet HWaddr 00:26:B9:44:11:3A
inet addr:213.8.155.33 Bcast:213.8.155.127 Mask:255.255.255.128
inet6 addr: fe80::226:b9ff:fe44:113a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]...
I have 17 system (sys1,sys2,sys3.....sys17) in my office, and i am willing to setup a dedicated system to act as a firewall for that i have selected sys1 with two NIC(eth0 for local network and eth1 for internet) and i have configured to access internet in my office for that i have opened a wellknown port 80.but my clients are not accessing the internet..
and please check my sample IP configuration !!!
interface : eth1 (ISP IP)just for example
IP :192.168.0.2
gateway:192.168.0.1
dns:202.56.230.5
dns:202.56.230.6
Interface : eth0 (my local lan )
192.168.1.1
255.255.255.0
IP address of xp clients ranges form 192.168.1.2 to 192.168.1.16 with default 255.255.255.0
my question is that which gateway address and dns i have to give to my clients for accessing internet ?...
I added an init script numbered just before bind9 starts, which needs to see the ipv6 link-local address on eth0. Sometimes this address is not configured, yet. In all cases it eventually is configured.
I am unable to find any script that is configuring the ipv6 link-local address (which is in part based on the MAC address). Does anyone know if there is some script or program that is supposed to be doing this, or is it an internal kernel function?
One workaround I am considering is making this init script go into a loop around sleep 1 to keep checking for the ipv6 address. But I'm concerned this might cause some problems. Any suggestions? I don't want to let it move on to start bind9 until the configuration this script does (more ipv6 addresses) is done.
This is on Ubuntu 9.10 server (for which there is not a prefix choice).
I need to setup two ethernets in my Centos box. OK no problem both ethernet and 1 virtual works perfect. eth0, eth1 and eth1:0. I'm trying to set up diferent routes for eth0 and eth1/eth1:0 I need eth0 has a 192.168.1.1 gateway and eth1/eth1:0 192.168.1.100 gateway.I think I've tried almost every thing but always get one gateway for all the eth.These are my config..
/sbin/ifconfig
eth0 Link encap:Ethernet HWaddr 00:XX:XX:XX:XX:XX
inet addr:192.168.1.168 Bcast:192.168.1.255 Mask:255.255.255.0[code]......
I'm having an issue configuring eth0. I'm using ubuntu 8.10 in a virtual machine (VirtualBox). The correct adapter is being used and it has worked in the past. I've tried placing eth0 in dhcp through the GUI and bash, but always get a 169 address or 127.
When I run the following command:
Code:
The output is:
Code:
after a yum update on my CentOS 5.3 I got this error when shutting down eth0 on reboot...
Shutting down interace eth0: Device eth0 has MAC address XXX instead of configured address XXX ignoring [FAILED]
you know ,we can get a Iface's MAC Address,IP Address,NetMask by function ioctl(), But how Can I get a Iface's Gateway by ioctl or other funciton!
View 5 Replies View RelatedAs a new user I like to know how to configure ip address, gateway etc in ubuntu 9.10. I used opensuse 11.1, their I can manage to do these but ubuntu I did not find anything.
View 2 Replies View RelatedI am coming across a strange error with my gateway. When I do a "ping", this is what I get below:
k-63a5b848c6cb4:~ # ping simba
PING simba.gateway.2wire.net (192.168.1.69) 56(84) bytes of data.
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=1 ttl=64 time=0.041 ms
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=2 ttl=64 time=0.029 ms
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=3 ttl=64 time=0.023 ms
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=4 ttl=64 time=0.015 ms
Is the gateway doing something strange?
I am using debain 6 and using a Sierra modem c888 to connect internet. I am using wvdial package for connecting the modem. I am able to connect internet. The question I have is, how do get the gateway address of the newly created ppp0 interface?
View 1 Replies View Relatedsetting up my ubuntu server I would also like to run ubuntu desktop for the GUI.
setting up the static ip address with a 2wire gateway from att.
I have two servers on a vlan at my datacentre/colocation and previously both servers had public IPs on their eth0 interfaces. The servers are HP ProLiant DL360s - one is a G4 and one is a G5 The newer G5 is now the LAMP server and the G4 has been retired and I want to repurpose it as an iSCSI target using openfiler freenas or similar.
My G5 has public/static IPs lashed to the eth0 physical interface and the eth1 is not configured to do anything yet. The G4 will have both interfaces available - perhaps one for ssh access from one of my static public IPs and the other to be a private IP on the local vlan. Here is what I am trying to get my head around...
The G5
eth0 - Public IP - full LAMP services on two or three virtual interfaces
eth1 - Private IP 192.168.0.1
The G4
eth0 - Public IP for ssh
eth1 - Private IP 192.168.0.2
Because my traffic between eth1 on these boxes is via private IPs on the local private vlan it doesn't add to my quota for bandwidth. How do I go about configuring the routing and gateways and other aspects of this so that I can run a private IP space network between the eth1s and still serve the outside world from the eth0s...
I am afraid that if I assign the private IPs to the eth1 interfaces the routing may either not work or interfere with the access to the production internet facing interfaces (eth0s).
