I am running Ubuntu 10.04 and i have some problems with my intel WiFi 5100AGN. After a randoom time i dont have a connection anymore and Ubuntu does not reconnect automattecly. I get an popup with the preinstalled password for my WiFi but for some reason i cant connect to it. I have a pastebin from the dmesg after it happens.: [URL]... It is tottaly randoom time it can happen in 1h and also in 6h.
View 2 RepliesI have a wireless connection with static ip 192.168.10.150 to connect to Internet through a modem / router ADSL ip Lan 192.168.10.1. I connect with no problems. I have a wired network in the office 172.16.17.0/24 to work with the servers. the router is 172.16.17.1, my connection eth0 with static ip 172.16.17.150 work, but Internet by Internet nothing. If i disconnect the cable i have Internet from wireless. ?? What i have to do to ,to received internet by wireless and be connected ate same time to my wired network by eth0 too.
all routers have DHCP active.
how to make dsl setup and to acess both wireless and wired at a time.
View 2 Replies View RelatedThis is not exactly Ubuntu question but i don't know where else to ask. I'm trying to setup a Wireless Linux router. My ISP provides multicast IPTV. I've got the whole thing setup'ed with igmpproxy and hostpad. On wired connection IPTV works flawlessly, but on wireless connection IPTV glitches badly and router start to time out. My wireless card is DWA-552 I'm using ath9k driver. More info in my post on LinuxQuestions.org Did anyone tried to setup Wireless Router with IPTV?
View 3 Replies View RelatedI installed Ubuntu 10.04 for the first time and had a few issues to put my laptop's wireless device to work (see thread [URL]I am now able to use the wireless connectivity but I still have a problem. Every time I reboot Ubuntu, the system does not seem to recognize that a wireless device is present. To overcome this problem I remove the driver and once this is done I activate the driver.The system then finds the wireless device, enables it and connects to the default wireless connection.
View 4 Replies View RelatedI have an issue with network-manager. When I edit my wireless settings and enable 'Allow all users' (I have a german locale so I don't know the exact words but I guess it's close enough) the connection drops and doesn't reconnect. If I click on the wlan access point manually (in the nm-applet) it asks for my WPA pass. This is odd since it was already in the wlan settings.
Then when I reset the 'Allow ...' to off, I'm asked for my su passwd and the connection is re-established. Ideally the nm would connect automatically at boot if the AP is available so I'm not happy with the current state...
In the right upper corner of your screen,you can see if you have a network connection or not.Most of the time I do not have one according to Networkmanager (?).So I have to enable my wired connection manually.I already tried a lot to change my settings so I would have a network connection at boot,but it doesn't seem to work....Firefox is in Offline modus when I logon..
View 2 Replies View RelatedWhen I have video running and the video stops, I see that the connection is destroyed in about 5 seconds, which is what I want. If, rather than stopping the video, I pull the plug, I have seen it take 350 and 380 seconds before the connection is destroyed. Why is there such a large difference in the time to destroy a video connection between stopping the video and pulling the plug on it when using net filter connection tracking? How can I shorten the time for the connection to get destroyed when pulling the plug?
View 3 Replies View RelatedToshiba A215 laptop
Driver is rtl8187
I really need to make the connection constant and non-dropping. I've had opensuse 11.2 since march 7 2010, figured out most of it by lurking and reading threads didn't want to make threads but I really don't know what to do to make this connection stay on. I am posting Terminal commands from when I am both on and offline.
How I attempted to fix this issue myself: I downloaded wireshark, wicd,knetworkmanager. Tried running all of them nothing worked. I went into Yast and switched off networkmanager and went traditional still nothing. Tried adding opendns to traditional. nothing. Went back to NM would get online then after an unknown time I'd lose connection even though NM said i was still connected. Offline running terminal commands from what I read on here in other threads and stickies
:~> ping -c 5 66.70.73.150
PING 66.70.73.150 (66.70.73.150) 56(84) bytes of data.
From 192.168.1.28 icmp_seq=2 Destination Host Unreachable
From 192.168.1.28 icmp_seq=3 Destination Host Unreachable
--- 66.70.73.150 ping statistics ---
5 packets transmitted, 0 received, +2 errors, 100% packet loss, time 4000ms
, pipe 2
:~> /usr/sbin/iwconfig wlan0 | grep Mb
Bit Rate=11 Mb/s Tx-Power=20 dBm
:~> sudo /usr/sbin/iwconfig wlan0 rate 24M
:~> /sbin/lspci -v
00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge
Subsystem: Toshiba America Info Systems Device ff10
Flags: bus master, 66MHz, medium devsel, latency 64 .....
Okay so I am a total newb to linux. I installed Ubuntu using Wubi and am trying to figure out how to get my wireless connection working. It occurred to me I may not have the right driver for use with Ubuntu for the wireless connection at my house. I couldn't find anything on the web to help..it appears I have a realtek RTL8102E wireless card in my laptop. I have absolutely no idea how to resolve this situation..I've looked on the web, but everythings pretty confusing. If I could get the wireless working it would be a good first step.
View 3 Replies View RelatedI have a wireless connection to the internet, as well as a wired connection to a local network. When the wired connection to my local network is enabled, the wireless connection to the internet no longer works until I disconnect the ethernet cable.
(This setup used to work just fine when I was using Windows, but now doesn't seem to work. I wasn't using IP aliasing in Windows, but I am now, which may be causing the problem.)
My original connection to the internet was a wired one, at eth0, so once I got wireless enabled (on eth1), I created an IP alias to my local network of eth0:1 which is a static IP on my local network. The only configuration I did at all was to add a file named /etc/sysconfig/network-scripts/ifcfg-eth0:1, with the following contents:
Code:
And NetworkManager just seemed to pick it up automatically - I didn't change anything else in NetworkManager or anywhere else.
(Also I use 'service NetworkManager start/stop' entirely rather than 'service network start/stop' to manage my connnections. i.e. I did 'chkconfig network off' when setting everything up initially.)
A friend who switched ISP's gave me his old Linksys WRT54-G wireless router. I went through the installation procedure and had a wireless connection up and running - smiley face. I had security set up for WPA, and decided to upgrade it to WPA2. Another smiley face. When I went to connect (had already done so successfully), I noticed it referred to my wireless as Linksys - I was expecting to see the SSID. So I started playing around in Network Manager and now I have things all effed up.
Don't know exactly what I did, but now I have no wireless. So I ran a few commands (lshw -C network, iwconfig, ifconfig, and iwlist scan), and looking at the results I see what appear to be inconsistencies in the output. I've posted them below, and make the following observations:
1. Under the lshw it refers to my wireless connection logical name as wmaster0, and has the correct MAC address, etc.
2. Under the iwconfig it says, 'wmaster0 no wireless extensions', but then refers to wlan0 as the wireless connection (although it does not seem to be running).
3. Under ifconfig I see both a wlan0 and a wlan0:avahi. The wlan0 has no IP, the wlan0:avahi does, but it is incorrect.
[Code]...
Its a case of ".... wireless network connection active but still not internet connection .."I am using WEP - 128 key ... Works when I connect directly using ethernet cable ... but not wireless (pci and wireless router)
ubuadmin@ubucomputer:~$ ifconfig
wlan0 Link encap:Ethernet HWaddr 00:06:25:12:83:3b
inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::206:25ff:fe12:833b/64 Scope:Link[code].....
Our F14 server is looses access to the network once we set a static IP.The same IP, if used on any other pc works fine.We had the same exact setup in our F10 server also.
View 9 Replies View RelatedMy problem is exactly the same as [URL]
but I am stuck at the last hurdle
here are the output of the command that helped to solve the case in the previous post:
ifconfig wlan0
wlan0 Link encap:Ethernet HWaddr 00:1b:77:d2:59:55
inet6 addr: fe80::21b:77ff:fed2:5955/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[Code].....
I have also tried sudo dhclient but it hasn't helped and I am still unable to connect to the internet
I have installed Fedora 11 recently. I want to share my Internet connection.
I have e LAN connection eth0 which is connected to internet.
I have a Wireless connection wlan0.
I want to share my internet connection with wireless connection.
I have two linux laptops. Currently, I'm using both of them at work, side-by-side. Now the problem is, I'm connected to a wireless router, but the wireless only works on one of the laptops. So I'm stuck with one laptop that has no access to the internet. Both machines do, however, have working ethernet nic cards. So, I was wondering if I could use the laptop with the wireless connection to share the internet connection with my other linux machine and access the internet on both of them. Or as an alternative, just use the internet on the machine without wireless and be able to switch back and forth, that would increase my productivity like 30 fold.
View 5 Replies View RelatedI'm using Filezilla to connect to a remote server with site 2 site VPN. Even when i'm sending a small file with SFTP, the connection time outs and reconnects. Its happening again and again. Even SCP connection is also the same. BUT SSH CONNECTION IS WORKING FINE.
Filezilla log
ravindika@ravindika:~$ tail -f filezilla.log
2010-07-07 10:35:12 2690 2 Response: fzSftp started
2010-07-07 10:35:12 2690 2 Command: open "root@XXX.XXX.XXX.XXX" 22
2010-07-07 10:35:19 2690 2 Command: Trust new Hostkey: Once
2010-07-07 10:35:21 2690 2 Command: Pass: *******
2010-07-07 10:35:25 2690 2 Status: Connected to XXX.XXX.XXX.XXX
[Code]...
Since upgrading to 10.04 my network connection asks for key/password every time I logon. Where/how can I make ubuntu remember my key/password?
View 2 Replies View RelatedI've been trying to use gnome-schedule to create a scheduled task that would dial my pppoe connection automatically. For this I used "sudo pon" command (after configuring the pppoe connection using pppoeconf ). Although the command gets executed, but then it waits for me to enter the password. I want it to be automatic & shouldn't require me/anyone to authorize it. Is there a way to enter this password automatically for the scheduled tasks?
Also, I'd like to use network manager, instead of pppoeconf, for the same purpose. How can I set network manager to dial a pppoe connection at scheduled time?
i use Huawei usb modem as default connection device , Why i have to connect and disconnect my usb many times to work properly? when i start my PC i have to connect and disconnect the usb about 5 or 6 times to get a connection to the Internet, the icon above shows that every time i get a successful connection but really i don't have it. i have to do it many times to get the connection actually established and the Internet truly works
View 2 Replies View RelatedI am running FC13 on a Compaq Presario 2100 using a Broadcom BCM4306. I was able to get it running thanks to Fedora Unity Project. But It's a very unstable connection. I don't know what settings to adjust or enable or disable. It's not my router, this is the only wireless connection in the house that I have trouble with.
View 1 Replies View RelatedI could not find an answer to this. I can connect to the internet no problem after I edit the connection name to NETGEAR instead of our last name. After a while it looks like it renews the connection and created a new one with the wrong name. The connection drops. It looks to me it is not using the same wireless connection each time but creating new ones that do not work for the above mentioned reason. What can I do to stop the loop and have it use the same connection always?
View 5 Replies View RelatedI am using Ubuntu 11.04 and a Huawei USB modem to connect to internet. Most of the time when I start computer it is not detected my system. Then I use to reboot and then it gets detected automatically. That means its drivers are now loaded. But I don't know why drivers are not loaded when I start first time.
View 1 Replies View RelatedSince the upgrade from Lenny to Squeeze on my Notebook Toshiba Satellite Pro U200 with Intel Pro/Wireless 3945 ABG I have wireless connection problems.The connection breaks time to time and sometimes cannot connect automaticaly after restart. BTW I didn't change anything on the wireless or network configurations on the notebook and on the wiereless router.
View 8 Replies View RelatedI am running Ubuntu 10.10, and I would like to use my computer to share the internet connection from an ethernet port. For example, I would like to set up my computer as a wireless access point so I can create a network that other computers can connect to for internet.
View 3 Replies View RelatedI noticed that it takes a couple more seconds before Ubuntu connects to my wireless network when it wakes up from sleep. I didn't have this annoyance when I was using 10.04, and only appeared when I upgraded to 10.10. It takes about 5-7 seconds before it indicates that it's connecting. When I was using 10.04, it only took a maximum of 2 seconds for it to indicate that it's in the process of connecting to my network.
View 1 Replies View RelatedI have a wireless Internet modem (USB) and a LAN Ethernet connection. I can only pick 1 of them to connect to (by disconnecting the other). How can I connect to both at the same time?
View 6 Replies View RelatedI recently purchased a TPlink 5 port switch, which for some reason didnt work with windows, only my ubuntu computer, I found a cheap wireless belkin router which also has 4 wired ports. It now works well except that it is slow searching for new servers eg, going to facebook creates a long wait and can even time out but once on the website everything works fast, The connection is 2.89 Mbps which is good for this area and ping is 45ms. What could I do to fix this problem. This affect my ubuntu computer and the windows xp pc as well
View 2 Replies View RelatedToday installed Ubuntu 10.04. The problem is that I cannot connect to the internet, which was no problem with the previous version (9.10). I use WiFi for my internet connection. My network is shown in Ubuntu. However Ubuntu cannot connect to my network. After some time trying it says : wireless network disconnected
View 9 Replies View Related