With the information given by Diaco, Lamp20, Shizeon, Backu and the writers of ttp://help.ubuntu.com/community/Dia...Howto/Conexant I have used a USB winmodem with a conexant driver in (K)Ubuntu 11.04 (Natty).When I plugged that modem, I executed
Code:
lsusb
and it said:
[code].....
I'm trying to use the modem which came with my laptop to connect to the internet. Unfortunately it's a winmodem, like most. The output of scanModem (attached) is not clear enough as to which driver should be used on this modem. I finally installed and configured sl-modem-daemon - but I still don't know which country should I specify, since Colombia (where I currently live) is not one of the available options. It appears, nevertheless, that my system is talking to the modem. I can't connect to the internet, though, since I always get this message with either Gnome-PPP or WvDial:
Code:
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
[Code]....
Also: the exact same setup works under Windows XP, so I know there's nothing wrong with my hardware.
Today I realized that my newly installed Natty does not recognize the Ethernet port, I used to have it when I was working on the Ubutnu 10.10. The following is the output (only the network related part) of lshw command:
Code:
-network
description: Ethernet interface
product: RTL8111/8168B PCI Express Gigabit Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
[code]...
I am new to Ubuntu and Linux. I think that I like Ubuntu, but I don't think it likes me! I can't get onto the internet with my "old fashioned" dialup that is preinstalled in my Dell Latitude. In fact I can't find any reference to a dialup modem in Ubuntu 9.10. Have done some research and it appears that my winmodem will not work with linux, but there maybe some complex way around this problem. Can it be done? I have a Conexant HDA D110 MDC V.92 modem.
View 9 Replies View RelatedI've recently switched over to Ubuntu 11.04. I installed Natty by wiping out Maverick entirely. Everything worked well, until I tried to install ATI graphics drivers through the instructions found here: [URL] The installation goes fine without any errors; however, when I reboot, nothing shows up on the screen. I can hear Ubuntu's startup sounds, but there are no visuals. When I attempt to go to the ATI Catalyst Control Center in Recovery Mode, I get this error:
Quote: There was a problem initializing Catalyst Control Center Linux edition. It could be caused by the following. No ATI graphics driver is installed, or the ATI driver is not functioning properly. Please install the ATI driver appropriate for you ATI hardware, or configure using aticonfig.
I've tried uninstalling and reinstalling these drivers multiple times, and I've also tried using the generic driver detected by "Additional Drivers". None of these work at all, I cannot see anything on the screen when any ATI drivers are enabled. I've even tried re-updating Natty via CD, but none of this works. I have a Radeon HD 3450 graphics card, and my CPU is an AMD Athlon 64 X2 Dual Core Processor 5400+. I'm on 64 bit Ubuntu. I had no problems with my drivers on Maverick.
I just did an install of Natty into a separate partition and incurred several problems. I have a Dell-DXP061 with 4 GB of memory and an Nvidia GForce 7300LE and a Dell 27in. monitor at a resolution of 1920x1200.
Initially it booted in to Ubuntu Classic as expected due to needing a proprietary video driver. So the first thing I did was to install the recommended Nvidia driver and attempted to reboot. It would not start either Unity or Classic. So I did a re-installation and then selected the experimental open 3D driver and was then able to bring up the system in both Unity and Ubuntu Classic. I installed a number of programs including cairo-dock, which I really like, emacs23, and gnucash. I have used gnucash for years and consider it a necessity. However, the Natty version will not display correctly the "gnucash-data" file I created with version 2.2.9 that I have been running on 10.10. This is almost a show stopper for me.
When I try to do a restart, the screen goes black, "Ubuntu" appears with the little dots, three of the dots change color and the system hangs. The system only stops when I hold the power button to effect a complete power outage. Interestingly the LiveCD did not seem to have a problem with restart.
I can see how a causal user might like the Unity interface, but I don't think that I am interested. I guess I will stick to gnome for a while, at least until Gnome3 and then I am not sure where I will go.
I have a conexant D480 MDC modem on my Dell Latitude | D800 but I am unable to Instll it,I have also tried using Gnome PPP,And it also says that no modems were detected on your system , Following are the error codes it generated Quote:
--> WvDial: Internet dialer version 1.60
--> Cannot open /dev/modem: No such file or directory
--> Cannot open /dev/modem: No such file or directory
--> Cannot open /dev/modem: No such file or directory
is there any way to setup an internal conexant pci modem?
1) linuxant free drivers are limited with NO FAX funcionality
2) i won't buy linuxant license, i have a old serial modem, at least i can use that... But i'll be more happy if i can use the pci one
I want to install conexant modem in fedora 11 I have installed modem with this guidance [url] But I have a problem When I want to run hsfconfig .This problem is Building modules for kernel 2.6.29.4-167.fc11.i686.PAE, using source directory /lib/modules/2.6.29.4-167.fc11.i686.PAE/build. Please wait... done. Warning: no device detected by hsf driver - HDA modems may require reboot Note: HDA support not compiled in the driver Note: kernel module snd-via82xx-modem overridden by hsfmc97via Note: kernel module snd-intel8x0m overridden by hsfmc97ich hsfmc97sis Note: kernel module snd-atiixp-modem overridden by hsfmc97ati. My modem is conexant hsf modem and I installed in fedora 9 and 10 without problem.
View 10 Replies View RelatedMicrophone (internal & external) is not working.
This is widely known and documented on the internet, and apparently no trivial fixes (alsa settings etc.) will solve this issue.
The best written reference for this is this Ubuntu bug tracker page: [URL]
It also doesn't work in Ubuntu but a person there (c4pp4) managed to create a patch for this.
Do you think this patch could be integrated into Fedora? What could I do to make this happen? Also, do you recommend any other approaches to this issue?
I have installed Tvtime and XawTv applications and I am currently trying to configure both these applications to detect my tv tuner card (pixelview play tv pro with conexant cx2388 chipset). configure both video and audio with channel scan for my tv tuner card?
View 2 Replies View RelatedI'm using Ubuntu 10.04 on Acer Aspire 5536. Used efax-gtk debian unstable package v3.2.3 to send a .ps file. Even by running software with root privileges the output is:
Code:
Socket running on port 9900
efax-0.9a: 11:28:27 opened /dev/ttyS1
efax-0.9a: 11:28:27 Error: tcgetattr on fd=7 failed: Input/output error
[code]....
Decided to first get ride of input output error. using sudo wvdialconf /etc/wvdial.conf command:
Code:
Editing `/etc/wvdial.conf'. Scanning your serial ports for a modem.
Modem Port Scan<*1>: S0 S1 S2 S3
If you still have problems, send mail to <wvdial-list@lists.nit.ca>. Using setserial command returned a huge syntax text. Modem is recognized under windows and it is HDA CX11270 Softmodem. How can I get it to work?
When I try to capture a video with my Conexant BT848 capture card, I get this error:
** ERROR: [lavrec] Error queuing buffers: Device or resource busy
The command I used is lavrec - software-encoding - format = a - input = P - quality = 100 - geometry = 912x576 file.avi
I have server ubuntu natty 11.04-64 bit, Yesterday, I Think I had been hacked by someone..
How to create report to see log for brute force attack?
I have some port opened 80, 53(bind9), SSH(22), Port Squid & some port java
I am Also worried that Guy is create other username for login
How to check that?
Is it possible to recovery HISTORY at ubuntu..?
It has been haunting me for weeks and I haven't been able to fix it so far: When I installed the wireless driver 43XX series on my laptop using a wired internet, I saw the wireless network for a while and after I rebooted my system, My kernel(31) got corrupted and I got error "kernel Panic (and some sync error)",Thus I started using an older kernel(14),Now When I install wireless driver or mobile broadband driver(wvdial), they get vanished after the reboot and my mobile device modem isn't detected.But they are installed in my system(as shown by synaptic package manager but doesn't seemt to work) I desperately want to use mobile broadband.
View 1 Replies View RelatedHow To: Uninstall/Remove Old Wireless Driver to make way for New Driver (RTL8191SE)?
Here's the new driver:
I have been having trouble with my wireless connection intermittently disconnecting and reconnecting repeatedly (sometimes every couple of seconds). I posted a thread about this here on Ubuntu Forums titled: Ubuntu 10.45 & NetworkManager Applet 8.0: Connects & Disconnects Frequently.
I just installed ubuntu and I have no wifi connection. How would I download and intsall a copy from my Win XP boot?
View 2 Replies View RelatedI have a lenovo g555 laptop, about a week old with lucid installed, and whenever i try to play things through the headphones, they come through the speakers as well. I've tried tinkering around in alsa, but the ony two levels are Master and PCM, which seem to adjust both headphones and speakers at once. My audio codec is "Conexant ID 5069"
View 2 Replies View RelatedI've installed fedora 15 on my laptom and im don't having sound. I know that there is a problem with the new HD intel sound card. Im on Aspire 3830T, with Conexant ID 506c. They had the same problem in ubuntu but they solved the problem: [URL]
View 5 Replies View RelatedI have Centos5.4 loaded on a late 2008 MACBOOK Pro and would like to get wireless working. I've attempted to download the broadcom driver and create a driver module with no luck.
Using these instructions....
[url]
When I make the WLAN driver, I get this:
How do you set wireless speed in natty? I've tried
Code:
sudo iwconfig wlan0 rate 54M
but nothing happens. I've tried this with wireless enabled and disabled (using network-manager), with and without the module loaded (ath9k) and using the solution provided in some forums (adding the command in /etc/rc.local and in a script in /etc/network/if-up.d) but to no avail... link speed always shows up as 65M.
I use an Atheros AR922X wireless card in my router/access point and everything was working fine under maverick. Now when I try and start hostapd I get this:
Code:
root@puffin:~# hostapd -d /etc/hostapd/hostapd.conf
Configuration file: /etc/hostapd/hostapd.conf
ctrl_inerface_group=0[code]....
I just updated my work laptop to Natty: perfect. My home server: perfect. My oldish home laptop: no more wireless. [I use wicd instead of Knetwork (or whatever it's called) because I want a permanent connection no matter the user]
I have a D-Link DWA-645. I get the whole stage: connecting, authenticating, etc... and bad password at the end. The password is correct (hasn't changed during upgrade). I also tried disabling WPA and it still won't connect. That's wlan2.
I also tried with an older PCMCIA card that _used_ to work on ubuntu 9, but stopped on version 10: a D-LinkDWL-G650. It doesn't even show up as wlan0 as it used to. I also tried with a USB-wifi DWL-G122 which has always worked on every version of Ubuntu [I don't normally use it because it's not practical on a laptop]. I see it as wlan1, but same thing: won't connect. Note that like with wlan2 I can scan for networks and see several around. For instance:
Code:
$ iwconfig
IEEE 802.11bg
ESSID: off/any
Mode: managed
Access point: not associated
Tx power: 20 dBm
Retry long limit: 7
[Code]...
[Edit]
Some more info: the access point works fine, I can connect with another device. The driver in use by Ubuntu is ath9k. Using KnetworkManager instead of wicd doesn't change anything.
I want to try and get apache and php working on Natty. I have got apache displaying an index page but when i try to show a php file firefox just asks me if I want to save the file and doesn't display the file in the browser.I installed using some info from websites to install al LAMP Server which seems to have finished ok.I have tried using php from the command line to see what happens and it seems the html is being generated ok.
View 1 Replies View RelatedI have spent the last two weekends trying to get Vista and Ubuntu(natty) to work together.From Ubuntu:
- I have disabled ufw
- setup a shared directory at /mnt/public (Permissions on public are 777)
- Ubuntu can access Vista shares.
- From the GUI, the "Network Servers" directory contains a "Windows Network" directory, but the Windows Network is empty.
- I can ping the Vista machine
From Vista:
- Nothing is visible. The ubuntu PC itself is not listed in the "Network" folder or map.
- I have disabled all firewalls (including the router)
- I can ping the ubuntu machine by IP address but cannot access it by IP address through
- "Run" - I enter \192.168.1.50, then get the logon pop-up. I enter the ubuntu creds, then receive a "Windows cannot connect to \192.168.1.50..." error message.
- "Command Prompt" ftp (or sftp) - I get connection refused.
- via "Web Browser" - I get the following message: "It works! This is the default web page for this server. The web server software is running but no content has been added, yet." The problem is that it doesn't work.
Everything I have googled up so far has been problems connecting in the opposite direction. I am trying to get to the Ubuntu machine. Although I checked all the smb.conf, inetd.conf and a few other files that I've seen mentioned, I cannot get the Vista machine to connect to the ubuntu machine.
i've installed ubuntu 11.04 on a friends Asus Eee pc 1005HA netbook. after the installation i tried to connect to the router using wireless, and when i enter the key, it fails to connect, so i tried using an Ethernet cable to connect but that doesn't work either,the network devices on the computer are:
Atheros AR8132 PCI-e fast ethernet controller
Atheros AR 9285 wireless network adapter
It lists the wireless device and the solutions to the problem, however, the solutions seem to be for Ubuntu 10.04 and also 10.10, and im not sure if it will work for 11.04 so far i have been unable to find out anything on the forums about the ethernet
I work in IT, but networking is my weakest area.I'm getting very slow DNS lookups (60+ seconds with lots of page timeouts)in Firefox and Chromium on my Kubuntu laptop. Windows clients (xp and 7) work fine.
View 7 Replies View RelatedI have an old ibm thinkpad R40. I did a fresh install of natty. Cannot get wireless or wired to work. I just want the wireless to work first if possible. So I have no Internet access. Can't upgrade etc. I am a noob and need to be hand held and walked through process.
View 9 Replies View RelatedWhere can I find details of how to set up a Huawei E173 on Natty? The network interface's status icon shows first "waiting for authorization" then it goes to "not connected" The modem hardware is showing up when it is plugged in:
Code:
$ ls -la /dev/ttyUSB*
crw-rw---- 1 root dialout 188, 0 2011-04-28 19:18 /dev/ttyUSB0
crw-rw---- 1 root dialout 188, 1 2011-04-28 19:18 /dev/ttyUSB1
crw-rw---- 1 root dialout 188, 2 20$ lsusb|grep Huawei
Bus 001 Device 013: ID 12d1:1436 Huawei Technologies Co., Ltd. 11-04-28 19:18 /dev/ttyUSB2 What needs to be done to get it working?
Reading recent posts, it seems that 11.04 has seriously screwed wifi.
I have an Advent QRC430 laptop which worked perfectly until I upgraded to Natty. Now wifi is broken. The wifi driver is rt73usb.
When I run lspci in terminal, no wifi card is listed. Running rfkill shows wifi hard blocked, but the switch on laptop makes no difference.
I've installed and run Hardware Lister - this shows wireless interface "has been disabled"