So i have a d-link modem and the DHCP server is not running. I need to access the internal config to do some troubleshooting. IP is supposed to be 192.168.1.1, but I only have my DSL ppoe IP, and can not access it.
View 3 RepliesRunning Gentoo with kernel 2.6.29 on a Sparc Ultra 10. I'm having problems with my cable modem connection failing, so I've added a static route that enables me to log into the modem's diagnostics page at 192.168.100.1 when the connection drops; my /etc/conf.d/net looks like this (with the comment lines removed).
Code:
dns_domain_lo="MYNETWORK"
config_eth1=("192.168.0.1 netmask 255.255.255.0 broadcast 192.168.0.255")
config_eth0=("dhcp")
routes_eth0=(
"192.168.100.1/32 via 0.0.0.0"
) dhcpcd_eth0="-N"
This works but after a period of several hours to several days, this static route disappears from the routing table.
I've been using an old modem from 2007, which my ISP calls Type I. It didn't have wireless connectivity and I used pppoeconf to setup my connection - username and password and set it to connect at boot time and everything was fine till today. I bought a Type II modem from my ISP and had to return the type I modem to them. Since the technician had no knowledge of Ubuntu (or Linux in general), he configured the modem in Windows 7, tested that the connection was working, tested the wireless connection in my netbook running XP and then he left.
Now I can't connect through pppoeconf in Ubuntu (running 9.10). The terminal says eth0 is listed but the 'access concentrator' or something like that isn't responding (no other process was running at that time). I feel very vulnerable while browsing in Windows so I want to get back to Ubuntu ASAP. Oh, and here's the output when I run "dhclient eth0"
Code:
Listening on LPF/eth0/00:16:76:33:d2:70
Sending on LPF/eth0/00:16:76:33:d2:70
Sending on Socket/fallback
DHCPDISCOER on eth0 to 255.255.255.255 port 67 interval 7
DHCPOFFER of 192.168.1.5 from 192.168.1.1
[Code]....
my computer with ubuntu 9.10 is in a LAN. We use static ip and do not have dhcp. I can go up to our server and browse our website but cannot access internet. my ifconfig, iwconfig, lspci are as follows...
[Code]....
I have 2 ubuntu PCs, which are connected to the internet without an external IP (behind NAT). How can I access one from another?
View 3 Replies View Relatedi have a problem with connecting to AP with static IP. i have set the IP, netmask, and gateway manually thru network manager but still no luck. the status is connected but i cant even open a webpage. ifconfig command output not showing the IP address i entered.
View 1 Replies View RelatedI assigned a static ip to my Ubuntu Server machine and it cannot access the web now. It can access anything on the LAN. The other two nodes on the network (one wifi one hardwired) can both access the web just fine.
View 1 Replies View RelatedOur F14 server is looses access to the network once we set a static IP.The same IP, if used on any other pc works fine.We had the same exact setup in our F10 server also.
View 9 Replies View Relatedthe bsnl modem cannot access the ubuntu 9.10
View 2 Replies View RelatedI have a usb modem : huawei e220.I am using ubuntu 9.10. I can't access the internet using it. I made a connection form the mobile broadband tab but every time it disconnects .Ubuntu identifies the modem but every time i try to make a connection it fails.
View 5 Replies View RelatedWhen I type my modem configuration page IP in browser instead of showing configuration page it shows default web page for apache.What's wrong?Is there any IP conflict?
View 1 Replies View RelatedUp until yesterday I was able to access these devices through the web interfaces that they use. I'm running Ubuntu Karmic 9.10 I have 3 PCs running on my network, and 2 NAS devices: Ubuntu (main computer, also has an XP partition)) - static IP 192.168.1.30 Ubuntu netbook - DHCP IP Windows XP (HTPC) - static 192.168.1.50 Linksys NSLU2 (was running Debian, problem arose when trying different configuration, now back to stock firmware) - static IP 192.168.1.100 Dlink DSM-G600 - static IP 192.168.1.120
I used to be able to able access these just fine using my main Ubuntu setup. Now, it will no longer display the pages. Internet access is fine, i can even access my DSL/Router device's internal config page. The netbook and the Windows HTPC can both log into these devices, as well as the XP partition of the Ubuntu system. I have tried using a VM of XP within Ubuntu, bridging the network device, i have the same symptoms - internet is fine, cannot access local network web-logins.
Access to fileshares among all machines remains unchanged. another odd behavior is that i can SSH into the NSLU2 device from all the machines, but i get odd things from this computer - it will let me log in, asks for a username and pass, but if i run anything like mc or htop, it just blanks the terminal in an odd way. from other computers the login and display are fine.
[Code]...
I spent $70 on a brand-new Wireless-N adapter for my Ubuntu computer in hopes that I could get it to connect to the main router in the house and get me internet access. However, the driver install CD is designed for Windows and thus will not run. I have tried to get it to set up, but it takes no action when plugged in and I am still without access to the internet. what I can do to get my computer connected and save me from having wasted $70?
View 9 Replies View RelatedIve got two connections, one is the eth0, that is the LAN connection to the DSL modem (192.168.1.1) and the other is the DSL connection that I connect to use the internet. Now I can only connect to one of the two at a time, so when I'm connected to the internet, I am not able to access 192.168.1.1. How do I use the two simultaneously?
View 8 Replies View RelatedI have a simple system at home where a DSL router is used as a basic dhcp server with one port forward for ssh to a server. I need to allow my daughters, ages 14,12 and 10, to access the net and also email but I want to have complete control and logging. What I'm looking to do is set up the Ubuntu file server I already have on the network to act as a gateway and also add content management and logging as step one.
I also want to add an email server so that all the email comes into the Ubuntu server and then is allowed to be accessed by outlook on their machines after spam/content scanning for valid emails as step two. My question is what, if any, additional software do I need and what options do I have. I've played with dhcp servers at work but never got much beyond ip assignment and network booting so I'm unfamiliar with what is needed for content management and such. As to the email server I've never even played with this at all so I'm completely in the dark as to what I should be looking at to start with. I'm looking for directions, RTFM is fine but right now I'm not sure even WHAT manual/manuals I should be reading.
I just installed Lucid Lynx Ubuntu on my computer. I love it, but I do not see how to configure my dial-up modem and connect. I'm hoping it's still possible. Here's my hardware.
333mHz Pentium III
Lucid Lynx 10.04 LTS
US-Robotics 56K Faxmodem External
256mb RAM
ISP OmniLEC
I've used Samba for several years and when it works it's great. Unfortunately from time to time it seems to get messed up and either all the 7 machines on my home network can't be seen or I can't access the shares on some. I have 2 Windows XP computers 4 Kubuntu and one Linux Mint KDE, all the latest versions. I'd rather not plough through all the documentation for Samba, but would really like a "model" smb.conf with a few comments about parts that might have legitimate variants. I have researched this with Google searches many times but have failed to find the information I need in concise form.
View 4 Replies View RelatedI have 2 pcs at home. I dont have a switch so I can connect only one PC at a time to my adsl router/modem for internet access. In the past I had successfully connected the two PCs (NIC to NIC) to each other using the same ethernet cable which was supplied with my dlink adsl modem.
Recently the motherboard of on of my PC went bad so I replaced it with a new one. The problem is when I connect the two using the same Ethernet cable they won't connect. The lights on the Ethernet port won't light up. I can still connect both of them to the adsl router (NIC to Router) (one at a time).
How do I decide what IP address to enter in my config file when assigning a static IP. All of the instructions I can find say something like "of course you should modify the file according to your own settings." Should I just use the gateway and IP that returns from "iwconfig" and "route -nee"?
View 5 Replies View RelatedI have fedora 12 installed in my laptop. Can anyone plz tell me how to connect nokia E51's modem ( via. Data Cable) to access GPRS !
View 2 Replies View RelatedI am wanting a computer with an external dialup modem (ppp0 modem through a com port /dev/ttys1) to act as a gateway to the internet, forwarding internet traffic through ethernet (eth0 is set to static 192.168.2.2) to a router (the router is 192.168.2.1) where it will be broadcast to other wireless computers like my laptop (192.168.2.3). I've had this setup until recently when the gateway computer (the one with the modem) died. Now I'm replacing that machine with another box and an install of Ubuntu 10.10 but so far things aren't working for me.
Success so far:I have dialup access working on the new box. Took me a while to work out the configuration for getting dialup working, though the IP address is Dynamic (or it won't stay connected), "Check carrier line" is off, and "Ignore Terminal Strings (stupid mode)" is on in order to successfully connect and stay connected to my ISP. I also had to make my normal (non-root) user "lancer" a member of the "pid" group (the reboot) in order to use gnome-ppp as non-root. The laptop (192.168.2.3) is successfully connecting to the router (192.168.2.1) as I can see the router configuration page when I type http://192.168.2.1 into the laptop's web browser. This setup is unchanged from how I had it before when this was previously working and I don't want to change how the router itself is set up. What I want is to know what to fix in the new box in order to get it connected to the router (through ethernet) and bridging the internet through.
My problem is that whenever I plug in the eth0 from the gateway (192.168.2.2) to the router (192.168.2.1), Ubuntu's automatic plug-me-in network detection kicks in and I find my dialup no longer working through some kind of IP conflict (at least that's what I think it is). Maybe I don't have the "gateway" correctly assigned? (in the gateway computer for the ethernet connection, I had it pointing to itself as I don't know what to put for "gateway IP" as that is automatic So, just to check my connection, here I am pinging google (from the gateway computer which has the dialup modem) once a dialup connection has been made.
Code:
lancer@lancer-desktop:~$ ping www.google.com
PING www.l.google.com (74.125.237.17) 56(84) bytes of data.
64 bytes from 74.125.237.17: icmp_req=1 ttl=55 time=179 ms
64 bytes from 74.125.237.17: icmp_req=2 ttl=55 time=176 ms
64 bytes from 74.125.237.17: icmp_req=3 ttl=55 time=158 ms
[Code]...
What do I need to do in order to make Ubuntu of my gateway computer stay connected to my dialup but also simultaneously share an ethernet LAN to my wireless router and feed traffic to the other computers from there? I have googled this but some of the most promising instruction (e.g. http://www.ubuntugeek.com/sharing-in...in-ubuntu.html) call for packages like dnsmasq or ipmasq which seem defunct now in Ubuntu 10.10. Other pages seem to suggest dual-networks "can't be done" in Ubuntu [URL].. (what!?! I had it before my other gateway died)
I have fedora 14 and reliance netconnect Huawei EC325 modem. I am not enable to configure it. How to configure the modem by providing step-by-step instruction
View 1 Replies View Relatedfind and install modem driver for the Alcatel X200 USB modem?
I've been all over the internet trying to locate Linux drivers but no success. Alcatel's website says is not supported, only in Windows. I'm sure there's gotta be a way to use the X200 in Linux.
i'm running Kubuntu karmic and i've been using a 3G Huawei E1552 modem to connect to the internet, everything was going well when suddenly my modem stopped working. I've tried reconfiguring everything, i even reinstalled kubuntu from scratch with no success.Here's a part of my /var/log/debug
HTML Code:
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099883] usb-storage: device found at 7
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099888] usb-storage: waiting for device to
[code].....
I got this message on Friday from just one domain. uote:mailsrv.forthnet.gr #<mailsrv.forthnet.gr #5.5.0 smtp; 554 5.5.0 Your message was considered to be spam by the FORTHnet Antispamming Policy and was not delivered to the recipient. The following spam tests returned positive for this message:FORGED_RCVD_HELO,RCVD_IN_BRBL. For further information visitWe are not a spamming community but it seems we have a statice IP address that has a Reverse lookup to "myipaddress.static.lyse.net" and not my email domain. Would setting a cname mail.mydomain.no -> myipaddress.static.lyse.net cure this problem or are there more tricks to be performedOnce I have cured the FORGED_RCVD_HELO I can move to getting the IP removed from BARACUDA.
View 2 Replies View RelatedI want to configure a VPN over the Internet.I installed the 'openvpn' package, generated the key file, transfered it by a secure way to the client, and setted up the configuration file.
So, in that configuration file I input the IP addresses of the tunneled interfaces. Both IPs are static in the tunnel.
Then, I've heard somewhere that I can assign a dynamic configuration IP for the client. I do this registering a range.
Well, when I tried to change static IP to dynamic IP (changing '192.168.0.2' to '192.168.0.0/24') in the configuration file, the OpenVPN didn't work.
Obviously I don't know what I'm doing, and I really, don't believe that simply changing the IP will make it work, but I tried.
I hope I explained my problem as well.
My configuration file:
# OpenVPN Server Configuration File
dev tun 0
ifconfig 192.168.0.1 192.168.0.2
cd /etc/openvpn
secret key_file
In client I execute the 'openvpn' without the '--daemon' parameter.Then I want that my client uses a IP in a range (192.168.0.0/24, for example), instead of a static IP (192.168.0.2).I also thought to use a DHCP server, but I'm not sure that will work.
I have a cheap and cheerful netbook (Advent 4213) that I carry around with me running the latest lucid build, it has a built in 3g modem which I like cause I don't have to carry a dongle round with me.... which I continually lose anyhow I also have two data plans, one with Orange UK and the other T-mobile UK. The 3g modem is a HUAWEI Technology.
Both sims work for normal Internet access, I can connect to email servers, access web (both http and https) sites, but when I'm using the T-mobile sim Ubuntu One crashes after about 5 mins after attempting to connect. At first I thought it was a problem with either Ubuntu One itself or the lucid build, so I tried accessing the website interface.... I can login but when I go to view my files (I am assuming you are familiar with Ubuntu One) the page "load" progress bar gets so far and then stops..... it appears to be trying to access ssl.google-analytics.com, but just sits there and eventually times out, I am assuming this timeout is what is causing the Ubuntu One to crash.
Stick the Orange sim back in and everything is OK, go back to the T-mobile sim and it no worky anymore hence the reason I think this is a T-mobile issue and not something wrong with Lucid or Ubuntu One..
I recently got rid of the different panels on my desktop and replaced them with AWN bars. However, in doing so I have lost my Wally system tray icon, which was my only means of accessing the Wally configuration tool.
Does anyone out there know of another way I can start this tool? Is there a command I can run from the CLI to bring it up?
Or, has a better alternative to Wally come out in the last few months which I should be using instead?
I need access to Internet through modem connection.
I have 2 questions :
1.Can I do it by using normal telephone line ?
What are the credentials to authenticate (mean : user nad passwd) ?
2. How to configure modem connection in my ubuntu linux ?
My viewsonic monitor will only go to 800x600 resolution on ubuntu..I had a similar problem with centos but went in an manually configured as root the display GUI and increased the resolution. Is there any way to do this with ubuntu? 800x600 is annoying on a 17" high end monitor
View 6 Replies View Related