I need to setup an Ubuntu Server to handle backups over the network (probably rsync over ssh). That server will then transfer the backup data offsite over a secondary external data line.How can I configure the ethernet interfaces to handle such a scenario?
View 1 RepliesIts a case of ".... wireless network connection active but still not internet connection .."I am using WEP - 128 key ... Works when I connect directly using ethernet cable ... but not wireless (pci and wireless router)
ubuadmin@ubucomputer:~$ ifconfig
wlan0 Link encap:Ethernet HWaddr 00:06:25:12:83:3b
inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::206:25ff:fe12:833b/64 Scope:Link[code].....
I have the "Work Offline" problem: when I boot up, the icon on the toolbar tells me I have "No network connection". This is not quite true, since I can access the first page of any website - only subsequent pages are inaccessible. I get a message saying that Firefox is offline. However, when I uncheck "Work Offline" in the File menu, it makes no difference to this behavior.
The problem is on my Ubuntu Dell desktop, which is connected to the internet with cable broadband via a D-Link router (wired connection). It has worked fine up till now. I use Ubuntu 10.04 and Firefox 3.6.11. I am writing this on my Ubuntu Dell laptop which is wired to the same router, so I assume the problem is not the router. I have tried various strategies suggested in threads on these forums, including editing about:config, changing "allow" to "deny" in some lines of /etc/dbus-1/system.d/NetworkManager.conf and changing from Automatic (DHCP) to Automatic (DHCP) Addresses only, but no luck so far. The contents of ifconfig are:
eth0
Link encap:Ethernet HWaddr 001:aa0:91:a7:51
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets: 0 errors: 0 dropped: 0 overruns: 0 carrier: 0
collisons: 0 txqueulen: 1000
RX bytes: 0 (0.0 B) TX bytes: 0 (0.0 B)
[Code]...
If I comment out "auto eth0" as well, it makes no difference. If I uncomment both lines ("auto eth0" and "iface eth0 inet dhcp") then I lose the internet connection altogether.
1 linksys router: gets the net from PPPOE and give the network DHCP. The router IP is 192.168.1.1. 1 windows laptop that work wireless and wired. 1 debian desktop that work wired and not working wireless. THe problem with the debian desktop is like this: I have a TP-Link TL-WN321G installed and found by lsusb command. I make a wireless connection WPA Personal (just like the router settings) it says i am connected to the wl network but no internet connection. the route command give me this:
[code]....
I tryed with wicd who said that the connection is WEP (and it's not, it is setup to WPA on the router and the network-manager conncetion) and when i try to connect i get bad password. I tryed with network-manager uninstalled and no chance.
I installed Ubuntu 9.10 using the default setup (Gnome I think) and on my Gateway Notebook using a wireless connection. It appears to be working great and I can even see my Windows drives and network storage on my home office systems.I have also set it up to run my favorite Bible software on Windows running under VirtualBox. I then installed the KDE Desktop so that I can select either desktop when logging on.
However, once I am in the KDE desktop, I cannot connect to the internet. I have checked and double-checked and the wireless settings seem to be the same on both the Gnom and KDE Desktops but still no network or internet connection when using KDE. I might mention that I am using the 64 Bit version of Ubuntu.
I'm trying to setup network server for a week now and I was able to setup network in which i can ping the other workstation that is connected to my switch which is also connected to my server and I can also ping the server from local workstation.
I have 2 NIC, I use eth0 to dial to my dsl connection(ppp0 has the IP of my internet) and I use eth1 to connect to the switch and use to connect to the other local workstation
Now my problem is I don't know how can I share the internet connection from my eth0 or the ppp0 to my eth1 to the network, what do I need to be able to share the internet connection to the workstation that is connected to my switch.
I am attempting to connect Ubuntu 9.10 to the Internet.I have a network connection, and Karmic detects it fine. I can ping addresses within our network (e.g. the Windows computer in the next room), and I can ping the router, but if I ping, say www.google.com, it says "Destination Net Unreachable". Previously, in Jaunty, I had a similar problem.I found a workaround: launch Pidgin. Somehow, launching Pidgin temporarily edits my configuration. However, in Karmic, I have no access to Pidgin, however, and Empathy does not do the same thing. Since I have no Internet, I cannot "sudo apt-get install" anything.How can I get the Internet working?
View 5 Replies View RelatedI just installed Ubuntu Netbook 10.10 on my Lenovo ideapad S10e. Under the network manager it says that firmware is not installed for the wirless card but that is something for a different day. On the ethernet connection it attempts to connect via dhcp and then comes up saying it is disconnected. I attempted to set it as a static connection, when i do that it shows that its connected but I still can not connect to the internet.
View 2 Replies View RelatedI am trying to Setup citrix ICA client 9 on Ubuntu 9.04 Server. I installed it very easily and I am not getting any lib error also. But when I try to connect to the citrix server, it fails with a pop up saying "Error in Network Connection Network or Dialup connection may be preventing ......" This is driving me crazy from 3 days. My project is to check the feasiblity of a Linux desktop
View 1 Replies View RelatedI've got access to my LAN and the Internet via my wired ethernet connection. I'd like to share that access with my iPod Touch (device shouldn't really matter) via an Ad-hoc wi-fi network.
This tutorial in the docs seems to describe the right setup but is very out of date (7.04). Instead I found this tutorial and followed it to create the Ad-hoc wireless network. I was able to connect my touch to the resulting ad-hoc network without a problem, but I didn't have LAN/Internet access.What's the next step to get the clients on the ad-hoc network out to the Internet?I found this page in the docs that says I'd need to install dnsmasq-base and uninstalling dnsmasq. I checked and dnsmasq-base is already installed but dnsmasq is not. I do have dnsmasq in /usr/sbin but the package description makes it sound like this should come with dnsmasq. Is the page out of date? Will uninstalling dnsmasq cause other problems?
I've read a lot on the internet about various ways of doing this but i've been unsuccessful each time. Basically what i've done is accidently un-installed network-manager because I was having trouble staying connected on my WPA network. The easiest way of reinstalling it I know of is using the CD but I don't have a CD ROM drive and the pen drive I used to install it I no longer have.
I tried using a program called Keryx but you need python installed and from some reason this doesn't come with ubuntu 10.10. I've also downloaded the .deb packages but I still need to download 200kb which is a killer. I've also downloaded it from here too [URL] but the install file makes no sense to me as i'm not a massive linux user. One last thing reinstalling isn't really an option as i've already put a lot of time into setting up this computer.
Okay, a couple of weeks ago I was running 10.04, got an auto update that needed a firefox restart, so rather than restart, I just shutdown the computer for the weekend. When I booted the computer on Monday it would find sites (www.google.com, start.ubuntu.com) but it wouldn't download the necessary items to load the page. Now I have a windows laptop sitting next to the ubuntu box and it was online with no issues, so I know it wasn't the connection itself. So I decided that the update messed up the system so I downloaded 10.10 and installed that and ran that all last week.
On Friday I got a system update that required a firefox restart, so I ran firefox for the day and decided that since it was friday, I would just shutdown the computer and reboot on Monday.Well now Monday is here and now I again have sloooowww internet, to the point that URL.. times out and won't come up. I have tried doing a traceroute on both machines and the windows box gets all the way to www.google.com, but the ubuntu box gets about halfway there and then gets no response. I am at a loss, I don't want to reinstall every week. I did try to reboot and run the previous version of 10.10 that shows in the boot menu, but that does the same thing. One thing I did notice is that the broadcast ip is different than the machine IP, don't know enough to know if this is a problem.
I have installed centos 5.5 / 64. Configured network but - no internet. On my router I see my pc and IP. On centos, Firewall and selinux are disabled. I try to disable network and activate network manager and reverse but no luck internet is not working. Try to ping my router 192.168.5.1
View 6 Replies View RelatedSometimes either due to a power outage or due to lightning I turn off my Wimax modem and continue to use my laptop on the battery.Then when I turn the modem back on, there is no internet connection.Here's what I've tried:
1. turn off and on the network connections - right-clicking on the icon on the bar on top of my screen.
2. turn off and on the dsl-provider connection - no effect.
3. When I tried to re-do pppoeconf, it says that there's no response from the concentrator.
This has happened a few times in the past and the only thing I can do to go online again is restart the computer. And it works.Now on Windows, the double-computer icon showing a network indicates connectivity AND data movement. Unfortunately we don't have this on Ubuntu.I'm just after a restart and I'm online now. But I'd like to know if there's a way around this without having to restart.
I'm running Ubuntu 9.10 with fluxbox installed. Occasionally my internet connection will stop working, but when I check on wifi radar, I'm still connected to the network. The router is not plugged into a computer at the moment, just the cable jack. It is likely a hardware problem however, since my other laptops also experience disconnects. Any help beyond "change the cable" would be greatly appreciated. For instance, even though I am connected to the network, I cannot post at the moment due to lack of internet connection.
View 1 Replies View RelatedI have a Ubuntu 10.04 laptop that gets its Internet connection via WIFI using WICD as network manager, and Windows XP desktop with no Internet connection. What I want to do is share my Internet connection from my laptop with my desktop via a Ethernet cable. But i have no idea what to do. How do i go about doing this?
View 3 Replies View RelatedI'm new in SUSE 11.4. My problem is: I'm using Alfa AWUS036H card. It's recognised and I can establish connection to my network, but cant get to Internet. I can't surf the web cos Firefox tell me that connection is timed out. Now I'm confused why I can't surf the web even if I'm connected. Also, I trayed to instal linux drivers for this card folloving Ubuntu "how to" and it just dont work.
View 4 Replies View RelatedHow do I tell the shared connection that it has a static IP and that I dont want a DHCP on the network?Do I have to set up DHCP on the box with the shared connection, even if that box only runs DHCP for a single IP address being the eth0 that is shared?Or can I tell the shared connection that it has a static IP and still allow network manager to run the shared connection?Or should I specify static IP's for all clients and the shared network manager and install say firestarter on the gateway to run the NAT for the eth0 out to eth1.
View 3 Replies View RelatedI dual boot windows xp and ubuntu 10.04 LTS and the wireless card works perfectly fine in xp so I know its not a hardware/network issue. In ubuntu, it detects wireless networks, will connect to network and work for about 20 seconds.
[Code]....
and it continues on after this alternating between a normal 20ms and high ping over 200ms. The connection refuses to load anything off the internet/local network.
After i install it i lost my internet connection . i got a message " Wired Network " " you work offline ". i use cable ADSL ,.... my Pc information HP Pavilion 6700 running with both Window 7 & Ubuntu 10.10 note... my network connection work correctly on W7.
View 1 Replies View RelatedI recently installed fedora 15 on my computer but I have a huge problem. I can connect to my router wirelessly for a couple of minutes only. Afterwards my computer has no Internet connection although the network manager and the icon on the upper bar says that i am still connected. I tried editing the /etc/rc.local and /etc/resolv.conf as mentioned in other posts in here bit no luck so far.
View 6 Replies View RelatedI installed the driver for my network card. iwconfig and ifconfig are all responsive to connecting to the network, I'm given an access point address. Then, I try to connect to a website and no dice. ping www.google.com yields no result. What gives?
View 2 Replies View RelatedI am losing network bandwidth and I am quite frankly I am not sure why, I don't have allot memory 495.6Mib
But I clean my PC every few days "BleachBit"
I have read some where on the magazine Network receiving suppose to be higher. so how can I fix this issue please i am having allot problems, u use cable from Comcast
I am not quite sure what Information you might need from me to give.
I use Ubuntu 8.04 LTS
I have a Broadcom Corporation NetXtreme BCM5721 network card on my server at work.Everything works fine for a few weeks, then randomly the network connection on the server will stop working. After it stops working, I will try to reconnect with the network manager, it shows a wired connection available, it shows the "connection in progress"animation, then the "connection disabled" icon.
I uninstalled the network manager and used manual configuration, but do you think the network manager was the issue? I can't have the server disconnecting randomly every few weeks with no way to know what the real problem is. Was there an issue with the network manager with 10.04?
I have 2 computer: 1 computer install ubuntu v9.10, in this computer already installed openssh-server and openssh-client, and 1 computer install windows. In computer with windows , i used putty connect to computer with ubuntu, but i can't connect. I don't understand what's error.
In the Putty , i configured:
IP : IP address of computer Ubuntu.
Port 22
Connection Type SSH
This is error: "Network Error: Software caused connection abort"
In computer with windows, i can ping computer with ubuntu and in computer with ubuntu i can ping computer with windows.
So I recently installed Red Hat 5.5, I'm able to access the internal network, including viewing pages on the intranet (however they load very slow, perhaps an unrelated issue). I can see that RedHat is properly resolving IP addresses, it just times out when it tries to connect to them.
route:
Destination Gateway Genmask Flags Met Ref Use Iface
15.28.184.0 * 255.255.248.0 U 0 0 0 eth0
169.254.0.0 * 255.255.0.0 U 0 0 0 eth0
default (hostname of 15.28.184.0) 0.0.0.0 UG 0 0 0 eth0
I have installed qemu/kvm and created a Bridged network connection which works just fine(Windows 7 VM won't work in NAT mode.)
But when I try to use NetworkManager it says that I have no network connection because the network isn't managed, (I set the settings in ifcfg-br0 and ifcfg-eth0 to be managed)
The real problem is that now I can't use my VPN connections (I have many) in NetworkManager.
Is there a way to have both of these pieces of functionality?
I am using FC14
OpenSuse 11.4 Asus Netbook 1000H Following other members in the forums I have installed Opensuse 11.4 on the Netbook. In the early days Ubuntu Netbook Remix worked well for me. But this has been discarded, and the "one size fits all" Ubuntu had become slow and cumbersome. So..... onto my post. Opensuse is working well. The install went beautifully.
It detected the Wireless Internet and I am able to get on line. I also need to share the Internet connection to a desktop. This is done via a small network switch. Thus far I cannot do this. I tried to use ifup to configure a static ip but this busted my Wireless configuration. I went back to knetwork manager. Then I tried to set up the wired network using knetwork manager and under IPV4 "share" the connection. But this blanks out any possiblity of a static address and substitutes dhcp. My desktop cannot ping the this dhcp address. Ubuntu had this thing called Firestarter? - from memory. This configured the system to sharing the network.
I am working on a cross-platform application for Linux ,Apple and Windows, so I have a full tower system with four SATA hard drives that be selected with a switch, so that I can change drives and operating systems at will. -sort of makes me a jack of linux systems, but master of none.It's important to mention this, because it shows the strangeness of the problem as it is isolated to Debian* systems.
So where does debian/ubuntu get it's information to establish a network connection?How do I rectify the problem? I can hardly blame the hardware (RTL8111B), because the problem is isolated to Debian systems.
It is just 3 days that I am using Linux Opensuse 11.2. I got a problem with Internet connection: I have HUWAEI E1550 3G Modem, but I have no idea about using it on Linux OpenSuse 11.2. Now I use it Windows7, there is no problem, because there is a program and driver for modem.
View 1 Replies View Related