I cannt get connection of my WIFI modem on UBUNTU 9.10(new installed) but it works on ubuntu 9.04(installed through WUBI.exe) without any driver. below is my lsusb report on UBUNTU 9.10
[Code]....
I have new emachine 1401 and I can't get it to connect to wireless. It does detect networks but when connecting keeps asking for password over and over and never connects. I don't have wired connection at all and the wifi router is not managed by me, so I'm retyping output through my windows xp samsung netbook which works over the same wireless network...
I have tries some other solutions I found around here (install bcmwl-kernel-source, rt3090-dkms_2.4.0.4, blacklist rt2800pci...) so it's not original configuration but behaves exactly the same.
[Code]..
On install my wifi was working, but when I rebooted it stopped working.Since then I've tried numerous things to attempt recovery of wifi. No luck so far.
View 14 Replies View RelatedI just did a Wheezy reinstall (I just started using LVM on LUKS), but my Ralink RT5370 usb wireless adapter wouldn't work, even though I have firmware-ralink installed. When I click on the Network Manager icon, it lists my home network (WPA2 passphrase) as available, but clicking on it yields no result.
Before the system reinstall, I've been using the adapter with firmware-ralink without problems. As far as "apt-get update && apt-get upgrade" goes, my system is up-to-date.
I tried uninstalling and then reinstalling firmware-ralink (rebooted too), but to no avail. The adapter seems to be undamaged.
Here are a few pieces of info that might be useful:
Code: Select all$ uname -a
Linux watershed 3.2.0-4-amd64 #1 SMP Debian 3.2.60-1+deb7u1 x86_64 GNU/Linux
Code: Select all# lsusb
...
Bus 004 Device 007: ID 148f:5370 Ralink Technology, Corp. RT5370 Wireless Adapter
[Code] ....
I just purchased a RALINK WIRELESS G PCMCIA WIFI CARD VISTA/LINUX (UBUNTU).
It is supposed to be UBUNTU plug and play out of the box with no driver downloads needed.
I installed it but could not find a way to search the active Wi-Fi networks available like on my Actiontec card on windows xp. The wireless router/ethernet I have is an Actiontec setup for Qwest-DSL and Actiontec is the name of the wireless network.
Strangely I tried to choose setup a "new network" and entered Actiontec as the network name and it found the network and said it was connected to it. However the internet still is not working?
Has anyone ever heard of this card or have knowledge of how to configure it to allow me to get on the internet?
View 1 Replies View RelatedI have an HP DV6 3143se which has a Ralink 3090 wifi card in it.the only thing that doesn't work at the moment is the Wifi. I tried installing the Linux backports module, but the trouble is that sometimes, my home wifi network is shown on the list of available networks and most often, it's not. when the network does show up, and i click on it and enter my WPA2 password, it takes ages to handshake and then it tells me that my password is wrong. the same password works in windows 7 so something's not working.
when i try to disable and re enable wireless network on the network manager applet, i get a Wireless device not ready or Network manager not running message.
[Code]....
I recently bought a HP g62x laptop for myself. It sports a decent Core i3 processor, 4 gigs of RAM and a 500GB HDD. It also came with Wireless-N, a real bonus because I am using a Wireless-N router. The chipset is a Ralink 5390. It came preinstalled with Windows 7, and everything works fine in there (obviously).
I then proceeded to install Ubuntu 10.10 x64 a few days ago (this is before Natty came out) and everything worked . . . except WLAN. So I plugged in via Ethernet and went looking and found that I clearly wasn't the first to discover this issue. I found a guide here that I followed to download the Ralink Linux driver (which is stated to support my chipset), configure, compile, and install. Everything went perfectly, I restarted; lo and behold, I have a list of access points. I went to connect to mine, entered the password, and now the animated "WiFi wave" logo keeps going indefinitely until you click it, and it freezes for a few minutes. It will unfreeze if you let it sit but clicking it causes the same freeze again.
I couldn't really care less about a WiFi icon freezing, but a.) it freezes everything else in the system up, not just the icon, and b.) it never actually completes the WiFi connection. I really, really don't want to be forced to use Windows because of a crappy WiFi driver!
Since Natty came out I installed that and I can't even compile the driver without fatal errors, so I reverted to 10.10 and everything is the same as it was before. Note that this is a clean Ubuntu 10.10 Desktop Edition 64-bit install, nothing updated/modified/changed besides (attempting) to install this driver.
i'm running Kubuntu karmic and i've been using a 3G Huawei E1552 modem to connect to the internet, everything was going well when suddenly my modem stopped working. I've tried reconfiguring everything, i even reinstalled kubuntu from scratch with no success.Here's a part of my /var/log/debug
HTML Code:
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099883] usb-storage: device found at 7
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099888] usb-storage: waiting for device to
[code].....
I've followed these instructions exactly but when I get here: Quote: Reboot and you should see an ra0 interface when you run the command 'ifconfig'
[Code]...
i am trying to get skylink 802.1n usb wirless adapter working under ubuntu 10.4 lts.https://help.ubuntu.com/community/WifiDocs/WiFiHowTowell, it seemed to see something at first:
user@host:~$ lshw -C network
WARNING: you should run this program as super-user.
...
[code]....
my wifi and dongle usb modem both are not working doesn't work on dell laptop inspiron 1520 withn opensuse 11.2.
View 1 Replies View RelatedI installed the driver from Ralink (2011_0406_RT5390_RT5392_Linux_STA_V2.5.0.3_DPO) and followed the instructions in other threads and my card does not work. I am getting this message.
"$ dmesg | grep -e rt5 -e wlan
[ 14.454006] rt5390sta: module license 'unspecified' taints kernel. I have also installed the Ralink RutilT program using synaptic. I can see my wireless device and many others around me but I can't connect.
I am dual booting with windows xp on a dell computer I recently acquired. I am running Ubuntu 10.10. The computer didn't have a wireless connection so I installed a wireless pci adapter from a company called ZONET. I installed it perfectly on windows xp, however, I cannot install the driver and the "Ralink Wireless LAN" on Ubuntu. I inserted the cd, and opened the setup.exe file with Wine Windows Program Loader (I have installed Wine 1.3 by following the instructions on http://www.winehq.org/download/deb and clicking on the link that says "click here".
I am currently temporarily connected to the internet by borrowing my main computers ethernet cable). I followed the instructions on the InstallShield Wizard only to have two windows pop up saying there is an error (see attached image).
I have a WiFi modem. Its Chinese(non-brand) modem. I can use this modem in windows Xp easily. Just need to install a software given with this modem. but cann't use it in Linux as using ubuntu 9.10 below is my lsusb report.
Quote:
ubuntu@ubuntu:~$ lsusb
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[Code]....
I tried ubuntu and am very happy with the smooth running and clean interface. I am having trouble setting up my network connections. It seems that I am unable to connect to the internet via my broadband modem if I am connected to my LAN via wifi. I think I need to seperate the networks so that the internet traffic does look on the lan for [URL]. I don't think I have had this problem when I used much smaller distros where I had to set it up by hand.
I might need to add some details I am just not sure what is relevant. I only have a basic understanding of what is going on.
solution:
Solved in #ubuntu irc chan with help by erUSUL.
Just in case anyone else is searching for the same thing.
In network connections in the ipv4 settings tab I edited routes by clicking the button and checked the box next to: "use this connection only for resources on its network"
Bus 001 Device 005: ID 148f:2070 Ralink Technology, Corp.
ifconfig
eth0 Link encap:Ethernet HWaddr 00:eb:01:00:fb:bc
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
[code]....
I'm using Ubuntu netbook remix 9.10 with kernel 2.6.31-21-generic i686.
other forums to get my Zonet ZEW1642D to work on my new install of Ubuntu Studio 10.10. None of the how-tos I've found APPEAR to have worked although I guess I'm not entirely sure how I would know. There is a pair of computers at the top right of my screen by the date/time. When I right click there the following are all checked:
Enable Networking
Enable Wireless
Enable Notifications
but when I click Connection Information Auto eth0 is the only connection that comes up (which must be the wired connection I'm using to submit this) Here are the things I've tried:
1) README_STA included in the driver files downloaded from the Ralink website although I must admit this was a bit over my head
2) http://ubuntuforums.org/showthread.php?t=1045703
3) http://www.hyperborea.org/journal/20...i-ralink-3062/
[Code]....
I am running 64-bit 9.10 on a Acer Aspire 1810T. I can connect to the internet via both wifi and the Novatel U998 modem. I have a PPTP VPN that works correctly via wifi, but does not work via the modem. The obvious problem would be that the ISP is doing something... but I'm dual booting Windows 7, and the ISP's Windows based software is able to connect to the VPN without issue.
I'm running VMWare player to be able to access my required Windows apps, so I'm almost in a position to dump MS if I can get this VPN issue resolved.
Just installed Ubuntu Studio 10.04 and everything seems to be working nicely except I have no networking.
The card does not appear in the Network Settings GUI. The only 3 tabs I have are General, DNS, and Hosts.
A screen grab is attached.
I'm a long time Windows user trying out some of the best Linux creative apps I can find. So, Ubuntu Studio was a no brainer. I checked the manufacturer's site for linux drivers and they are available, but I don't know how current. (Edimax site, not RaLink's site.) I opened the file and it looks like it needs to be compiled and installed to work. Something I know almost nothing about. The card is listed as supported in this forum for Ubuntu 9x but I can't find information about it for 10.04
PS. I have no networking on the system but I can transfer files via USB flash drives if needed.
Some System info:
Code:
1 ) Machine Brand and Model (PC/Laptop): Dell Precision 650
2 ) Wireless Brand, Model and Wireless Chipset: 03:0c.0 Network controller: RaLink RT2561/RT61 802.11g PCI
3 ) check interface: robert@ubuntu:~$ ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
[Code].....
if there is a simple wifi scanner for Linux. I need only basic information such as access points in the neighbourhood, signal strength and their broadcasting channels. I want to know the broadcasting channels in order to set my modem in such a way to avoid interference.
View 9 Replies View RelatedAfter having my usb wifi adapters working fine for some time, they stopped working and I can not get network connectivity.
Some one else was using my box and they reported seeing a kernel panic and then rebooted the box. Now there is no connectivity through the wifi interfaces.
I have seen the kernel panics related to this driver before, but usually a reboot has no ill effect.
Code:
root@Algalon:~# iwconfig wlan0
wlan0 RTxx70 Wireless ESSID:"a800" Nickname:"RT3070STA"
Mode:Managed Frequency=2.412 GHz Access Point: 00:0B:86:9A:08:80
Bit Rate=54 Mb/s
[Code].....
Im a Linux newbie and am running OpenSuse 11.3 (Gnome, 2.6.34.7-0.5-desktop Kernel) and Ive an Asus N13 wifi dongle (linux compatible). I currently connect using my laptopś internal wifi but I bought the dongle due to trouble with weak signal. It came with some sort of code that can be "compiled" but I havent got a clue how to do that (and I have been researching this matter for quite some time now). I then came across a post where someone with the same USB stick created and added only two small files to his filesystem and it worked...for him (maybe becasuse he was on a different Distro )
Ralink RT2870 USB Stick and created the two files mentioned in the post (network_drivers.rules and network_drivers.conf) and placed them in ETC... etc, etc! I rebooted the system but NetworkManager only lists it as "device not ready" ... So now back to square one.
[Code]...
I have a fit-PC server with Debian GNU/Linux (Lenny). I would like to use it as a wifi access point since my Linksys WRT54GS has become unstable.I have a USB Ralink wifi NIC. When I insert the card to USB I can see this with lsusb: Bus 001 Device 002: ID 148f:2573 Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter.I have tried following various HOWTOs on using wifi card as AP in Linux, however, it seems that the card cannot go into monitor mode. I believe this is because I must use a newer driver or upload non-free firmware or something like that.I have tried installed wicd, but it does not help.
I bought this wifi adapter because I was told that it is one of the most common used Linux supported wifi cards that can be used as access point and a lot of other stuff.How do I set up this USB wifi card as wireless access point in Debian Lenny?
I've just installed Debian Wheezy on my old Toshiba Satellite A10 (Intel celeron 2.20 GHz, 1GB Ram, 30 GB hard drive) and tried to connect to my home wifi network with a usb wifi adapter (Hamlet HNWU254G). lsusb in terminal says it is Ralink RT2501. Ethernet worked fine, so I installed firmware-ralink package, the adapter was recognized and I was able to connect.
However, I heard quite frequently a strange whistle and realized it came from the usb wifi adapter; it also got very very hot. Other strange thing: the computer some times freezes: screen flickering, loss of control of mouse and keyboard, need to shut down with power button.
At first I thought it was the video card not being powerful enough for Gnome (even classic), but then I installed Xfce4 and nothing changed. Instead, when working offline, freezes happen less frequently (but still happen).
I've tried the usb adapter on another laptop with wheezy: it gets hot, but there are no whistles and freezes.
Im using usb wimax modem for qubee. its web address is [URL]
in terninal after giving the lsusb command i get the following output
sanjoy@ubuntu:~$ lsusb
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[Code].....
after that I give dmesg>output.text so a text file I goet which is attached. output.zip
Imagine this scenario at my home: I'm working on my laptop using WLAN receiver as I have a router installed at my home. Suddenly the electricity fails (it's a regular incident here in Bangladesh called Load-shedding) and the power source to modem and router dies.As a result, my internet connection drops. To connect to the internet without power, I use this QUBEE UH-235 WiMAX USB Modem. Now I know QUBEE may not be there in your country. But after a bit of research I figured that this UH-235 modem is commont every country. QUBEE just branded its logo on the device and the software within.This one is not my device, mine is here.
In my windows, the software is installed as soon as I plug in the USB. That software then detects the modem, scans for network, and then connects to the internet. No extra CD is required for this. However, on an Ubuntu machine, I can't get it working. I guess there are ways to get this UH-235 modem working on my Ubuntu machine. This is keeping me from using Ubuntu as you know I'll have to restart and log in to WIndows whenever electricity is off as Ubuntu works with Wi-Fi, not this UH-235 modem when the Wi-Fi is out of power
I have received a new huawei k3770 usb modem but ubuntu 11.04 (32 bit) picks it up as a cd rom but not as a modem. Modeswitch is installed and I have reinstalled it as well. I have googled it but I found nothing.
View 3 Replies View RelatedI just can't seem to get this thing going. I've also tried Gnome-ppp. Press detect and it says "no modem installed" I did install it in Windows as well to make sure the darn thing actually works. It did perfectly.
Your US Robotics modem attached at /dev/ttyACM0 >>> The problemt: wvdial for some reason cannot use it
I had to edit the /etc/wvdial.conf file with gksudo gedit /etc/wvdial.conf
john@ubuntu:~$ sudo wvdial
[sudo] password for john:
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port
[Code]....
This is really weird, and I would like just this question answered: I've spent like 2 hours by plugging, unplugging, rebooting, and doing everything I could, but the modem wasn't working. When I did ls /dev/ttyU* it was showing up a list of 6 usb devices.
Code:
/dev/ttyUSB0 /dev/ttyUSB1 /dev/ttyUSB2
/dev/ttyUSB3 /dev/ttyUSB4 /dev/ttyUSB5
And when I sent the command wvdialconf after looking into all the devices, it didn't recognize any modem.
The thing is, that by the time I was writing here for a solution, I disconnected the modem, and when I reconnected it I did a ls /dev/ttyU* just to copypaste the info, and Voil! there were just 2 devices, and wvdialconf worked out just fine! I would like to know what I was doing wrong, so I make sure it won't happen again.
Oh, and I forgot to say: I use Ubuntu 8.04