Ubuntu Networking :: Connecting To Unencrypted Wireless Network From Command Line Installation
Jan 8, 2010
I am trying to do a command line installation.Finished the installation and my wireless card wasnt working.Did a "sudo ifconfig wlan0 up" and got it working.But for some reason wireless-tools is not installed thus I dont have iwconfig, iwlist, etc.The wireless works and connects fine off a liveUSB.So I am going to give info from this liveUSB run and maybe someone can suggest how I can set the right settings on the Command Line Installation I presume in the etc/network/interfaces.
I run Ubuntu, and it has a nice GUI widget thing that connects me to my home wireless network when I boot. I don't have a problem with that. But suppose I don't start X, and boot to a recovery console for some reason, like I did recently when my graphics were broken after installing Karmic. In that case, my computer won't be connected to the wireless network until I log into X normally. So I can't apt-get anything or anything. It's very annoying. And I don't know how to connect to my wireless network.
I know my wireless network SSID, and I know my WEP key or WPA passphrase. How can I log onto the network with commandline tools? Is there some basic program that I can just run "networkmanager <myssid> <mywepkey>"? I looked at the iwconfig man page and I honestly couldn't figure out how to simply connect to my network. Once I figure out how to connect to the network with command-line tools, where can I put an "autoconnect" script so that it will connect during startup, like it should anyway?
What I don't understand is, why the Ubuntu network manager nm-applet, doesn't just work as a front-end for more basic networking stuff. I don't see any reason why it should require you to start X before working; it could be a daemon that runs at startup, and there could be a config-file somewhere, but it doesn't even start running until I log onto gnome.
I have setup my wireless card via ndiswrapper and I can see that if I perform an iwconfig that the card is wlan0. I have attempted to connect with the router but I can't get any connection.I know the password is: ########## (10 digits long) but for the life of me I can't get it to work via command line.
I've been familiarizing myself with the command line and am attempting to connect to a wireless network but am getting stuck at the point wherein I need to put in a password.When I run iwconfig I see my card is wlan0.I definitely know my password as I can connect using a GUI. The encryption method for my network is WPA2.Could someone tell me how I could connect to a WPA2 secured network via a command line, and/or where I went wrong with what I've been trying?
My wireless is 'almost' working, but frustratingly not quite there. Debian Testing (squeeze). I have two different wireless adapters. Both work flawlessly from an ubuntu live CD in the same machine, connecting to the same unencrypted access point so the problem is not faulty hardware, weak signal, overpowering signal, interference from other AP's, MAC filtering, or anything to do with WPA.
I have loaded the correct (I think) firmware packages for both adapters. dmesg is not complaining about missing or incompatible firmware. I have googled the various error messages reported in dmesg and found that the /etc/Wireless/RT2860STA/RT2860STA.dat missing config file is normal. I could not find anything that I understood concerning the BSS returned, data->length messages but since I see the same thing in Ubuntu (where the wireless is working flawlessly) I assume they are also normal and not related to the problem.
Both adapters can see all the available access points (using iwlist {iface} scan or using gui tools such as wicd, wifi-radar) NEITHER adapter will associate with any access point (and I've tried three different unencrypted AP's so far). I can connect to all/any of these AP's from an ubuntu live CD using the exact same hardware, so this is NOTHING to do with MAC filtering, etc... using 'iwconfig {iface} essid' as root to set the essid "appears" to work, but simple does not set the ESSID on either wireless adapter.
Using the GUI tools (which are only a front end for the command line tools so I have no idea why everyone thinks a GUI front end like wicd will magically work where the command line tools don't!!) I simply wait a long time for "getting network address" before it eventually fails. LOTS of information in pastebin, please make the effort to read it before asking me for things I have already supplied. And please keep any "RTFM noob" or "go back to ubuntu" replies to yourself. I HAVE read the f*cking documentation and I do not want to go back to ubuntu. I just want to get my wireless working in debian.
I stupidly turned off my computer as I was updating to KDE 4.7. Now when i start it i get to the log in screen, but imputting my username and password just causes the Xserver to restart and i get back to the log in screen.I know there are many other packages I should install as part of the update and i think this will solve my problem, so i am trying to connect to wireless through the command line login, and then install the updates.
I am fairly familiar with Linux but had never ventured into Wlan settings / options / too much. I have compatible card (aetheros) and when running - iwlist wlan0 scanning - I get plenty networks showing up - meaning the card works. When I installed distro which is last night (before I ran update), I had that little bars menu at the top of the screen that showed available networks once clicked upon. Since I like to modify and make my settings better - I removed that little AT&T like bar, and now rebooted after update to find that I can not see available networks unless I use iwliset wlan0 scanning.... .#$*&)@&#(&%# - need I say more.
Two questions - how do you connect to the wireless network via command line? What is that vertical bars GUI tool called so I can find it and run it again? Is there (for the love of god) alternative to system-config-network GUI managment tool for wlan?
I'm tryn' to connect to my wireless network using command line:iwconfig wlan0 essid MY_NETWORK as root.
After this typingiwconfig wlan0 result is: wlan0 IEEE 802.11g ESSID:off/any Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:1 Mb/s
[Code]....
I installed ndiswrapper in order to use ipn2200 WinXp drivers.
I was wondering how to connect to wireless in a Linux command line environment -> I'm looking for a ncurses like program to do this, not a bunch of commands and files to edit.
I have a CentOS 5.5 server running currently with a Netgear gigabit ethernet card and for wifi I have a wi-fi card with the chipset: RT2860.Now I have gotten the ethernet card and wi-fi card working but my main question is: How do you bridge the connection between the ethernet card and the wi-fi card to create a wireless network with a hidden ESSID if possible and WPA encryption? (So the server basically acts as a wireless router as well as doing all the other stuff I need to do on it).
For reasons that are not terribly interesting I decided it would be a great idea to remove and re-install the xserver-xorg package. Which proved to be a much larger mistake than I imagined it would be. I purged the package, and then restarted.Naturally I need to have an internet connection to use apt-get to reinstall xserver-xorg, which is where my idea falls apart.I followed the directions in the How To: Manual Network Configuration. However, after I enter the command "sudo dhclient wlan1" I get the line "wmaster0: unknown hardware address type 801" twice prior to the output that the above link shows. Then I just get DHCPDISCOVER messages until I get a "No DHCPOFFERS received. No working leases in persistent database - sleeping."
I'm connecting with WEP to a router that I know works (because I'm using it to type this on my laptop right now) and I know that the wireless adapter(RTL8187) is installed properly because it automatically connected to my network when I had xserver-xorg still installed.I'm running ubuntu 9.04.I've searched for a few hours and I'm no closer to resolving the issue.
I did a command-line installation. I dont have an ethernet connection, only wireless. For some reason the alternate installer doesnt install "wireless-tools" How do i install it? At this point I am thinking of booting off a live USB, downloading the wireless-tolls package from here Save it to a folder in the command line installation where?) then boot back into command line and install from there But I am not that savvy with command lines, and dont know where to install to...
I have a machine running Xubuntu [2.6.22-14-generic]. I have been trying to get this machine connected to wireless for ages, and I'm having another stab at it. So far I have install ndiswrapper and loaded the driver for a Linksys wireless adapter. The output of 'ndiswrapper -l' reports:
So as far as my newbie knowledge goes, I believe that step to be completed, correct?When I turn on the machine is type in
Code:
sudo sh modprobe ndiswrapper
to get the card running to where it will appear in the iwconfig dialog.The commands 'iwlist wlan0 scan' will list all the wireless networks around me, but I have been un-able to connect to any network, even unencrypted ones. I have tried to connect both through Wicd and command-line to no avail. For command-line I have used:
Code:
sudo ifconfig wlan0 down sudo dhclient -r wlan0 sudo ifconfig wlan0 up
[code]....
With the final 'dhclient wlan0' commands, the following is returned:
Code:
There is already a pid file /var/run/dhclient.pid with pid 134519120 Internet Systems Consortium DHCP Client V3.0.5 Copyright 2004-2006 Internet Systems Consortium
[code].....
I have attempted to go ahead a step further and connect to an encrypted wireless network, however, I receive the same message, as well as another error message upon trying to enter the key, with the following code:
Code:
iwconfig wlan0 key s:"thekey"
Error for wireless request "Set Encode" (8B2A) : SET failed on device wlan0 ; Invalid argument.
Here is a situation I have never come across (though I have only been using linux since 2004).I am running ubuntu 10.04 and using Wicd Network Manager.I can connect to my WPA encrypted home network, but if I go to my coffee shop to use their unencrypted wifi - I cannot.Even using the terminal. I think it is the way the device sees the network - but I don't know how to fix it.I have a screenshot with wicd here:And one with connecting to the essid here:Afterwhich, dhclient was unable to obtain an ipaddress - just like wicd above.
My iphone connected to this network easily without encryption or needing to use the browser to authenticate, etc.Any ideas on how to fix this?Specs:Samsung NC10lspci:
I'm trying to connect to a wifi network where it hijacks all requests and redirects you to a page where you have to agree to a terms of use before it lets you connect to the actual outside world. This is a pretty common practice, and usually doesn't pose much of a problem. However, I've got a computer running Ubuntu 9.10 server with no windowing system. How can I use the command line to agree to the terms of use? I don't have internet access on the computer to download packages via apt-get or anything like that. Sure, I can think of any number of workarounds, but I suspect there's an easy way to use wget or curl or something.
Basically, I need a command line solution for sending an HTTP POST request essentially clicking on a button. For future reference, it'd be helpful to know how to send a POST request with, say, a username and password if I ever find myself in that situation in another hotel or airport.
I'm thrilled using wicd to connect to wireless networks. But when I suspend my laptop using the special keys, I just want to disconnect from wireless without having to use any kind of GUI or curses user interface. It says in the documentation that wicd works by sending DBUS messages, so presumably it's possible to write a command that talks to the daemon directly.But I can't figure out how.Does anybody know by means of what shell command I can tell the wicd daemon to disconnect me from my wireless network?
I am unable to connect to my home wireless network when WEP 128 bit encryption (open system passphrase) is turned on however I can connect when I disable the encryption?
I would share my long awaited success with connecting my ubuntu laptop up to my universities (University of Western Sydney) wireless network. The rumors appeared true and they have finally implemented 802.11x authentication instead of that horrible java app netdirect. I am sure you've been cursing at its erratic stability. There is no linux documentation for airUWS-Lite nor anything more imformative than there windows/mac point and click steps found at [URL]. However with a few simple clicks you can have stable working connection.
When connecting make sure you have theses settings. Security: WPA & WPA2 Enterprise Authentication: Protected EAP (PEAP) #This is the settings that does not present itself correctly Anonymous Identity: leave blank PEAP Version: Automatic Inner Authentication: MSCHAPv2 Username: <YOUR 8 DIGIT STUDENT NUMBER> Password: your regular password
I have a fairly new install of 10.04 on a Dell laptop (about a week). Everything was running well, connecting wirelessly to the interneet through my home router (WPA/WPA2). Today, for some reason, I lost my connection to the internet. The network manager tells me I'm connected to my router, but all the lines on the wifi indicator are gray and there is no internet access. I reinstalled the 2 sets of packets for my BCN4312 (bcmwl-kernel-source and b43-fwcutter ), but no change.
The university I go to uses a WPA2 wireless network that requires a netID and password to connect too. I installed wicd but I can't seem to connect to this network, is there a way to add this functionality to wicd, and if so, how do I do that (links to a how-to or guide would be nice, I've yet to find one).
Also, I spend most of my time on campus in the command line, so I'd like to know if there is a way to use command line utilities to connect to this network (again, a guide or how-to would be nice)
I can get online through my fedora live USB just fine (w/ network manager) but I'd rather get on directly from slackware.
I noticed that it takes a couple more seconds before Ubuntu connects to my wireless network when it wakes up from sleep. I didn't have this annoyance when I was using 10.04, and only appeared when I upgraded to 10.10. It takes about 5-7 seconds before it indicates that it's connecting. When I was using 10.04, it only took a maximum of 2 seconds for it to indicate that it's in the process of connecting to my network.
i just installed Ubuntu 11.04 64bit on my desktop. i have a TP Link TL-WN321G (Ver 4.0) wireless usb adapter to connect to my wireless network (i used to use it with Windows XP).As expected (i'd read up a bit before installing Ubuntu), the adapter was autodetected - i could see my wireless network listed in the networks list dropdown, and lsusb showed it too.lsusb identifies "Bus 002 Device 002: ID 148f:2070 Ralink Technology, Corp. RT2070 Wireless Adapter"But i cannot connect to the network. When i select my network, it keeps trying to connect, but never succeeds in connecting.
i tried going through the forums for possible solutions, but most of them deal with how to get it working when the adapter is not detected, or when networks are not shown. Or they are for older Ubuntu versions.i use the same wireless network on my laptop (Ubuntu 9.04), and it has a WPA & WPA2 Personal security, with a password, which i've configured in the desktop as well.
I have a wireless router, but my desktop computer is connecting to it, or maybe to the modem, by an Ethernet cable. It has a built-in wireless card, so just as an experiment, I tried to connect to my network wirelessly. It didn't work. And not only did I not get any internet connection, I can't get any internet through the wired connection either. The internet works fine with Windows Vista (I'm dual-booting), as well as when I boot up Backtrack off of a Live DVD. I can still access my router's config page by going to 192.168.2.1 on a web browser, but I can't access anything else.
In setting up wireless connections I have ran into an array of problems. First, when I installed the new OS on my laptop I had to get the correct drivers and firmware for it to display and connect to any connections, had no problem here connecting to a secure wireless network (WPA or WPA2). I then installed Ubuntu on my desktop and had to find the correct driver for the Netgear WNDA3100v2 USB adapter, got it all installed with the Windows Wireless Drivers tool or w/e it is. This made all the available connections come up. I tried connecting with the WPA password I was given for the network and will not connect.
I had the guy managing the network change the one I connect to, to a WEP Passphrase Shared Key thinking this would solve my issue, still nothing. And also in doing so, now my laptop will not connect to the wireless network using the Passphrase. I do not want to go back to Windows, and I will be getting rid of my Lan connection soon so i need a solution to fix this wireless connection problem.
I recently downloaded and installed CentOS 5.3 DVD media.The media check passed. I proceed to install the operating system sucessfully. After installation, all my hardware is recognized, when compared to CentOS 5.2. Anyway, when I attempt to connect to my wireless network that uses either WEP/WPA/WPA2-- I get an error message that I cannot recall (it basically only came up when I entered the key) However, I can connect to my wireless network when it is unencrypted and no open/shared key is needed.I would like to be able to connect to my wireless network when
FYI: I am using a RealTek RTL8185 Wireless Driver.Also, I use CentOS as a workstation.
I want to run OpenBox on a netbook. For those of you not familiar, it is a very simple window manager, where I can launch a terminal with a mouse click, and I can start the few apps that I need from the command line. Basically, I am trading eye candy and easy access to a lot of stuff I don't need for a more responsive GUI.
My question is...what package should I install, and what corresponding command line would be used to launch a tool to manage the wireless LAN connection?
I'm having problems with my wireless card. The network manager won't allow me to turn it on. It is working in windows and in ubuntu, but I can't get it to turn on under fedora. I'm using a Lenovo B570 laptop and it uses the Centrino Wireless-N 1000 for wireless.
Without Gdm (The GUI Desktop running), or an Internet connection, how does One get pppd or wvdial to connect to a wireless broadband modem?I'm SURE this can be done with any modern Distro without additional downloads...but seem to be missing some crucial step...? I've been trying things like: (scrips for pppd and chat and ln {links} ttyACM0 to /dev/modem?) the modem is definitely on ttyACM0.
The title about says it! I have a major problem on my laptop after installing updates. Some of my icons in the top panel are broken. So as a first step I need to reinstall a few things. The first step is to start the wireless connection from the terminal. So would someone please tell what the command is?
I wanted to run a little media server in my house, shared with my laptop only, so I could free up space on my laptop drive. I took one of my Linux boxes out of my render farm and loaded up a minimal install, command line only of Ubuntu Lucid from the mini ISO (32 bit). I had to plug in a lan cable to install, but I wanted to move my box back out to the "farm" that doesn't have wired access to my intranet.
After much research, trial and error, this is what worked for me. My wireless card uses an Atheros AR5001X+ chip, and it works with the desktop cd out of the box. I found the "just works" desktop install uses the ath5k driver that is now included in Lucid, but I'm not using a desktop or window manager. I haven't tried this on server version, if you do, let others know what you had to install to get it to work.
The things I do tell you about, I instruct you as if you are a newbie, however I have left out some things that users should know or be able to lookup easily, like if you want a static address instead of using dhcp. You may not need all of the steps or you may have to do more research and troubleshooting.
Find your wireless card (you may need to lookup what to do if it is not recognized at all)List all pci devices, only show network devices (-v verbose, -vv very verbose): >>lspci -vv | grep Network List all hardware (| less lets you pause at each page - arrow keys, page down/up to navigate, q to quit) >>lshw | less
