i cant connect to my wireless network... im using karmic. Ive searched and found quite a lot of threads but arent sure where to start. I have a Linksys wusb600n, and are trying to connect to my network. It detects the network fine but doesnt connect.
View 1 Replies
My OS is Linux Xubuntu 11.04 (32 bits) and I'm trying to get Linksys Wusb600n network adapter to work. I followed this post and did all that was written in it... almost. When i came to blacklisting, I blacklisted all drivers that starts with rtx (where x is any digit). Here are lines that I pasted in blacklist.conf:
Code:
blacklist rt2860sta
blacklist rt2870sta
blacklist rt2x00usb
blacklist rt2500usb
blacklist rt73usb
blacklist rt2800usb
blacklist rt2x00lib
blacklist rt2x00pci
[Code].....
The problem: I do see all available networks. So I guess... it somehow works. Anyway, problem is that it does not connect successfully to my network. I click on it - it asks my password. I enter it and click 'Connect'. Nothing, except that network icon is started to like spin around (trying to connect, I guess), happens. After few minutes, it asks for password.... again. I enter it and all starts from the beginning. Its like a loop! Note: I don't have any other things installed except linux-firmware-nonfree_1.9_all.deb and, don't know how successfully, but RT3572USB 2.5.0.0.
I'm trying to install a Linksys WUSB600n dual-band USB wireless-N adapter onto a desktop system with opensuse 11.1 installed; this system will be migrating to a back porch with no cabling access, hence the wireless solution. Everything works fine under Windows XP, but on Linux, not so much. Hardware info is as follows; there is no "Wireless LAN" entry, but there is a USB entry:
99: udi = '/org/freedesktop/Hal/devices/usb_device_1737_71_noserial'
info.subsystem = 'usb_device'
usb_device.vendor = 'Linksys'
usb_device.bus_number = 1 (0x1)
linux.subsystem = 'usb'
usb_device.product = 'Dual-Band Wireless-N USB Network Adapter'
info.product = 'Dual-Band Wireless-N USB Network Adapter'
[Code]........
I started a fedora 15 live cd last night, and at the top right corner, i noticed that wireless was not active. Right mouse button on the internet icon showed me that fedoar recognized the usb device as it is,, a Linksys WUSB600N wireless lan.
However, fedora warned me that the firmware was not available, therefore i was not able to configure the WUSB600N. To be specific,, it's the V2 version.
My question is,, does this device work with linux fedora? i assume that i need to install the required firmware in order to use the device.
After much tiddling'n'fiddling I finally got my new Linksys WUSB600N v2 working. Contrary to many posts, mine did NOT work with either the standard rt2870sta module, nor the updated version from the driver:wireless repo. Also the rt2870 version from the ralink website didn' t work. After a days worth of Googling I came across this post. The bottom line?
1. Download rt3572 from the Ralink website.
2. Add {USB_DEVICE(0x1737,0x0079)}, /* WUSB600N v2 */ to common/rtusb_dev_id.c
3. Follow README_STA
I did not install firmware packages. And be sure the rt2800sta module doesn' t get loaded. (you could just remove it, I suppose.)
I think lightning may have killed it. It was working fine. Now I cant get it recognized no matter what I do. It also quit working in Win XP where I never had a problem with it because it had its own connection software.
dmesg yields this-
RTUSB disconnect successfully
[ 312.876034] usb 2-1: new full speed USB device using uhci_hcd and address 7
[ 312.996021] usb 2-1: device descriptor read/64, error -71
[ 313.220031] usb 2-1: device descriptor read/64, error -71
[ 313.436038] usb 2-1: new full speed USB device using uhci_hcd and address 8
[ 313.556025] usb 2-1: device descriptor read/64, error -71
[ 313.780031] usb 2-1: device descriptor read/64, error -71
[ 313.996032] usb 2-1: new full speed USB device using uhci_hcd and address 9
[ 314.404022] usb 2-1: device not accepting address 9, error -71
[ 314.516021] usb 2-1: new full speed USB device using uhci_hcd and address 10
[ 314.924029] usb 2-1: device not accepting address 10, error -71
[ 314.924046] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 343.664017] pan0: no IPv6 routers present
[ 809.024049] usb 1-1: new high speed USB device using ehci_hcd and address 10
[ 809.182271] usb 1-1: configuration #1 chosen from 1 choice
[ 809.182837]
[ 809.182839]
[ 809.182840] === pAd = ffffc20020b41000, size = 598568 ===
[ 809.182841]
[ 809.182845] <-- RTMPAllocAdapterBlock, Status=0
guest3@guest3-desktop:~$
Im having another problem with my wireless in Maverick, Im at my wits end with this thing and dont know what to do next. I followed Dev0's from this thread.And now when ever I start my computer I get a notification that says "Linksys C" connected. Then only a few seconds later it says Disconnected and then from then on every few minutes the Password prompt pops up and then I enter my password and then it just keeps going in that cycle until I click cancel.
View 1 Replies View RelatedI'm new to openSUSE and as a matter of fact, to linux too. I've got a Linksys WUSB600N wireless adapter which used to work fine with some live versions of linux that I was testing out before moving onto suse... Each time, upon booting using live CDs, I used to copy the driver I had downloaded from:
SpeedShare - Download rt2870-kernel-2.6.24-nemesis.tar.bz2
Then 'make' and get into the driver's os/linux directory to load the driver using 'insmod rt2870sta.ko' Now, upon doing a 'make' and 'make install', followed by the 'insmod rt2870sta.ko', I get the error saying:
insmod: error inserting 'rt2870sta.ko': -1 Invalid module format
I tried doing 'modprobe -rv rt2870sta' and didn't get any error messages. But while doing 'modprobe -v', this error shows up: insmod /lib/modules/2.6.27.7-9-default/kernel/drivers/net/wireless/rt2870sta.ko
FATAL: Error inserting rt2870sta (/lib/modules/2.6.27.7-9-default/kernel/drivers/net/wireless/rt2870sta.ko): Invalid module format
My first Ubuntu/Mythbuntu install. Installed OS, plugged in linksys wireless G adapter. It finds the network but cannot connect. Discovered wireless priviledges while setting up admin/user accounts. Should be ready to go. or not, I'm thinking it needs a driver but
1) in linux? certainly not in Fedora.
2) If it can see the network it doesn't need a driver,
My settings are wrong or I'm missing something. SSID is set in settings. Do I need mac address and BSSID?
I've tried it using the Ubuntu 9.10 live CD (both 32-bit and 64-bit versions) and while the adapter can see wireless networks, it can't connect to them. It asks me for my WPA2 key, but after trying to connect for about 30 seconds it asks me for it again. I've read other threads about this issue but they were kind of confusing.
I just need to know whether the adapter will work and if so, how to get it to connect. I'm so sick of Windows and I'd love to switch to Linux, but I won't be able to if I can't get my adapter to work.
Edit: I just noticed the sticky about posting wireless tickets. I'm sorry, I don't have time to post it right now, but I will post all of that information when I get back.
I have an Acer Aspire 1 Netbook - this is running UBUNTU- When I try to connect to my Linksys Router in wireless mode it asks for password - but doesnt accept. I can see the Linksys in network manager plus several other networks in the vicinity. My other wireless devices all connect O.K. to the Linksys, and accept my password.. I can hard wire by ethernet to the netbook. Just wireless is the problem
View 3 Replies View Relatedi installed ubuntu 10.04 from internet.but i cant connect to my wireless router linksys wrh54g ver 1.0,but if i using Local area connection its working,however my wireless connection working in my other os win xp.
View 3 Replies View RelatedLinksys WUSB54GP Not Found, Can't Connect to Wireless - 10.04 Lucid Lynx
I am having a problem setting up my wireless on Ubuntu 10.04 (Lucid Lynx) on my desktop computer using a Linksys Wireless-G Portable USB Adapter WUSB54GP.
The wireless has run fine on my Thinkpad X60s laptop running Lucid and with my desktop and the same USB adapter in Karmic (9.10). When I installed Lucid as an upgrade on the desktop, I could not see the adapter listed at all and could not connect wirelessly to the internet.
if I need to install drivers, edit a file, or do something else to get this working I couldn't find anything useful to actually solve my problem after searching for a while.
This should be all the important desktop system specs: Linksys Wireless-G Portable USB Adapter WUSB54GP -- not found; can't connect to wireless internet
Lucid Lynx 10.04 (straight install from CD from Canonical)
Intel Pentium 4 630HT
ATI Radeon 4650HD
I see a bunch of posts about WUSB600N, often telling folks to download and compile proprietary drivers from ralink's website. With Ubuntu 11.04, getting WUSB600N to work might be as simple as disabling rt2870sta (for rev1). If you have rev 2 card, driver to disable is I believe rt3572sta. Even if you need to recompile drivers by hand, the right thing to do is to first try nightly build of rt2x00 drivers from [URL], and fall back to ralink provided drivers only if things do not work out with rt2x00 drivers. I saw recent updates on rt2x00 mailing list for rt3572 chip, give it a try if you have rev 2 card.
WUSB600N rev 1 (rt2870 chip) should "just work" with rt2x00 driver included with 2.6.38 kernel in Ubuntu 11.04. At least it works for me. You may need to blacklist rt2870sta driver from staging directory so that it does not load and interfere with rt2x00 drivers. There's one small annoying issue with power save mode on rt2870 chip when rt2x00 is in use, which seems to have just been fixed upstream. Most users will never notice it, but if you do notice card re-connecting to AP every 10-20 minutes or so, simply disable power saving, and all will be smooth (iwconfig wlan0 power off). If you have an older Ubuntu release (kernel 2.6.35) and rev 1 card, you should be able to download nightly build of rt2x00 driver from [URL]. It worked for me just fine with previous Ubuntu releases.
i'm very new at this and tried to install Linksys WUSB600N v2what i would like to know how uninstall any drivers/ software i may have already put on the os. how can i verifry that the device is functional after installing drivers.
View 1 Replies View RelatedFC13 i686. Trying to compile a driver for Linksys WUSB600N Ver. 2 from a Ralink driver.tar.gz. Below is a portion of the output of the compile, I can't put this whole output on this LinuxQuestions Website it is to large.
In file included from /lib/modules/2.6.33.6-147.2.4.fc13.i686/build/include/linux/usb.h:21, from /home/jim/Downloads/RT3572/2010_0709_RT3572_Linux_STA_v2.4.0.1/include/os/rt_linux.h:62, from /home/jim/Downloads/RT3572/2010_0709_RT3572_Linux_STA_v2.4.0.1/include/rtmp_os.h:42, from /home/jim/Downloads/RT3572/2010_0709_RT3572_Linux_STA_v2.4.0.1/include/rt_config.h:72, from /home/jim/Downloads/RT3572/2010_0709_RT3572_Linux_STA_v2.4.0.1/common/crypt_md5.c:28:
/lib/modules/2.6.33.6-147.2.4.fc13.i686/build/include/linux/sched.h: In function "get_mm_hiwater_rss": .....
I was wondering if anyone figured out the WUSB600N ver1 with Ubuntu 10.4 yet. It's the chipset rt2870sta which works perfectly on Ubuntu 9.10 after blacklisting the other RT2x modules but following the same steps as I would 9.10 on the new release of Ubuntu won't allow me to connect via wifi at all. I went back to 9.10 for now but was hoping this would be resolved soon.
View 2 Replies View RelatedI've managed to install my WUSB600N on 10.10 (which was NOT easy!!) and I can see all my local wireless networks, but I can't connect - it attempts to connect then disconnects after what I guess is timing out.I know that you can place these cards in broadcast mode (I think), where you can see networks but not connect. Considering that to get this card working I had to attempt about four different sets of instructions to get this far, could I have placed the card in a broadcast mode? I've been at this for about three days, and unless I go out an buy another network card (I'm currently connected using it through windows) then I'm going to have to give up on Linux, which I really don't want to
View 9 Replies View RelatedI have a laptop running 11.2 with an internal Broadcom-based Wi-Fi card that's working fine. I'm trying to get 802.11n going with the WUSB600N. The USB ID on this device is 1737:0079. I believe this means it's a "V2" with an RT3572 chip.
No driver loads for this device when it's plugged in. If I do a "modprobe rt2870sta", a driver loads, and syslog shows "rtusb init" and "usbcore: registered new interface driver rt2870". But ifconfig -a doesn't show a new network interface. I've also tried building the RT3572 driver from the manufacturer's web site. It builds fine, and modprobe will load it, but I get the same results as the rt2870sta driver.
I have just installed a fresh copy of 9.10 on an older Compaq nc6000 laptop. I need some help getting my Linksys WUSB600N wireless adapter to function properly.
I have "half-way" connectivity, meaning that I can see (and connect to) my home wireless network but I can't connect to the internet (unless I use the wired connection). I have installed NDIS wrapper - no change
well I am a novice in Linux OS, I have a wireless card, it's a Linksys WUSB600N but it doesn't work in Ubuntu 10.10 Desktop Edition, which it is the one I have, 64 bits machine, so I read this [URL] and I did all the steps, I downloaded 2010_0915_RT3572_Linux_STA_v2.4.0.2.tar but in the last part, sudo make install I got this error
alain@alain:~/t/2010_0915_RT3572_Linux_STA_v2.4.0.2$ sudo make install
make -C /home/alain/t/2010_0915_RT3572_Linux_STA_v2.4.0.2/os/linux -f Makefile.6 install
mkdir: cannot create directory `/etc/Wireless': File exists
make[1]: Entering directory `/home/alain/t/2010_0915_RT3572_Linux_STA_v2.4.0.2/os/linux'
rm -rf /etc/Wireless/RT2870STA
mkdir /etc/Wireless/RT2870STA
[Code],,,,
so i have no way to get connected to the internet, what is that error cannot stat `rt3572sta.ko': No such file or directory, I think thats why i can make the wireless card work.
I recently tried to install Crunchbang on my IBM Thinkpad T20 laptop. Everything went OK as far as I can tell (I still have to adjust acpi and display settings), but I cannot get my laptop to connect to the internet via wireless (wired connection works fine). I've done a good deal of searching online, and I realize that my wireless adapter (wpc54gs, bcm4318 chipset) is problematic in linux, and that b43-fwcutter is typically required. I did install b43-fwcutter, and it seemed to install OK, but nothing subsequently happened when I opened networkmanager. I'm not sure at this point if my problem is that I don't know how to configure any wireless adapter in crunchbang, or if it is that my particular adapter is not being recognized.
View 4 Replies View RelatedMy old ubuntu laptop beeps 3 time on startup and then freezes. This forced me to install 10.04 on a new laptop. Now I can't get the linksys wpc54gs ver 2 to get connect. I can see the router with a padlock by it. I pretty sure I have the correct password in the right spot. I can access the internet with the wire connection. I'm sure it something simple I forgot from before when the card was working in the old laptop.
View 2 Replies View RelatedI connect to multiple wireless system each day but when I encounter a Linksys-n router the computer will recognize it and connect but does not go online.
Does this give any clue for why it will not connect?
Code:
802.11a/b/g
System wireless is: Toshiba Satellite M115-S3094 with Intel PRO/Wireless 3945ABG (802.11a/b/g), Ubuntu 10.04
I am net to this whole Linux thing. I cant seem to connect to my Linksys router. Not sure if I have to call Linksys or what.Mine is a WRT54GS
View 1 Replies View RelatedI am a complete novice with Ubuntu trying it with a "Live CD" on a Compaq Presario 1700 (P3/700MHz/512MB) with a LinkSys "Wireless-G Notebook Adaptor with SRX400" (Model WPC54GX4 - using Windows drivers LSSRX4.bin & LSSRX42.sys, Airgo Networks Version 2.0.1.19).The PWR" and "Link" lights are "ON".This card works fine with WinXP.I have tried to set it up using the Network Tools and "editing" data into the "Network Manager Applet" (entered SSID, and a "WPA & WPA2 Personal" password), but no improvement.
View 4 Replies View RelatedI am trying to install ubuntu on an HP Pavillion dv7 laptop. The installation worked just fine. However, I cannot connect to our Linksys router wirelessly.
View 3 Replies View RelatedPreviously I had my desktop hooked up to a nearby router via an ethernet cord with my parents' computer having a wireless usb adapter to connect (This thing: [uRL]). We just moved and our setup has reversed (router is near their computer, I am using the usb adapter). I just installed the latest Ubuntu and now I can't get the usb adapter to work. I'm very new to Linux and I have no idea what to do. I think this is the same usb adapter.
View 1 Replies View RelatedI have a linksys wireless-b wmp11 network card. Can anyone tell me how to get this up and running? Maverick is up to date as of yesterday and I have the cd that came with the card. I have no way to access the internet on the machine. I am typing this from my laptop.
View 2 Replies View RelatedI have a dual partition with xp pro, and Ubuntu 10.04. It really is amazing, and i plan on erasing everything and starting over new again, this time just ubuntu. with windows, i have a Linksys Compact Wireless G usb Network Adapter with speedbooster ver.2. it works in windows from the CD, but its for windows. ive tried ndiswrapper-utils, ndiswrapper-common and ndisgtk downloads and it opened the program, but sat with the spinning circle for 5 seconds then faded to grey. HOW do i get this to work? i'm in a hurry, as i am leaving for vacation in florida, and i have the only laptop in the house and we bring it every year. If there is something easy (or complicated but with step by step) that i could use to get the driver for my usb network thingy,
View 2 Replies View Related
