I've just installed Ubuntu 10.04 on a Dell Inspirion 1501 and I can't get the internet to work. I've tried configuring a DSL connection from System> Preferences> Network Connections and It doesn't recognize the password. On Windows it works just fine.
View 3 RepliesI am using 10.04 and is trying to install the linux drivers for Nokia CS-10.However when I try to install the deb file, it doesnt work. The installation process starts then its starts another process then gives me the error which state I have to close the previous installer window.[URL]
View 1 Replies View RelatedI installed Ubuntu 10.04 into my compaq notebook. The problem is that I am not able to connect to my wired broadband internet.
Here are the details of my attempts so far:
1)"ifconfig -a" gave 2 devices eth0 and wlan0.
2)"pppoeconf" was unable to detect any ethernet cards.
3)Each time I plug in the LAN cable , the network icon would say "connecting" and ultimately result in "disconnected.Now in offline mode".My ethernet device is Realtek PCIe RT8101E/RTL102E (rev 02).
I also tried to install the realtek driver though I was not confident whether I did it correct.
How to connect Ubuntu to the Internet through a broadband connection? I decided to give Linux a try, and I picked the Ubuntu variant. I have some problems with the Internet connection though. I have a broadband (modem-less) PPoE connection, and all the info needed in order for me to connect are the username and password (which I have).
View 2 Replies View RelatedI am trying to connect to the internet from command line. i issued the command nm-tool the output is
Device: ttyUSB0
Type:Mobile Broadband (GSM)
Driverption1
state:disconnected
Default:no
capabilities:
I also issued the command sudo iwlist ttyUSB0 scan it gives this as output ttyUSB0 does not support scanning
I also issued the command
sudo iwconfig ttyUSB0 essid "MTN DEFAULT"
iT GIVES THE OUTPUT
Error for wireless request "Set ESSID" (8B1A)
SET failed on device ttyUSB): no such device
How can one find out the essid value of a broandband network? How can i connect to the internet from command line for a broadband network?
i recently-ish bought a netbook, and a mobile-broadband toggle to go with it, and set it aside to use later. i promptly installed the Netbook remix on the laptop. Well, I goofed, and didn't notice until well after I bought the WAN toggle that it was made for windows.
so, I downloaded Wine in an attempt to run the start.exe and get my internet. the executable (and the entire drive, i found) are marked by ubuntu as read only. Is there anyway to change this to allow me to run the file? if i did, would it even work?
I have a multiboot system running several versions of linux which do not all use the same software for handling wifi connections or have the same kernel. They have all stopped being able to connect to the internet in the last few days. My Windows 7 set up still connects though it seems to be a slow to establish a connection.Could BT have changed something and if so what?
View 4 Replies View RelatedI just installed Ubuntu in my PC and I tried to connect to internet using broadband connection. I use a ADSL router with WiFi access point to connect with network and dial my username and password using my computer to connect to internet.I could so it easily on windows 7 from Network and Sharing center and Setting up new connection or network and connect to internet using broadband internet.How can i do it with ubuntu 11.04 ?
View 9 Replies View RelatedI have installed fedora 12 recently. after installation i tried to connect to the internet using BSNL broadband connection. I filled in the details such as IP, Netmask, Gateway and even DNS servers. In the services also I ensured that the network manager services is on. However even though my computer cannot connect to the internet. I then tried the ping test of the modem from the address 192.168.1.1 and found that the ping test is successful. Then i tried the network administrator and there I noticed something unusual.
There are two options in the devices eth0 and eth1 thats ok but the unusual; thing is that the Activate (green button), Deactivate (red button) and even the delete buttons are in the background and I cannot select them. Isthis the problem for the network connectivity.
[Code]....
I then tried the ping test of the modem from the address 192.168.1.1 and found that the ping test is successful. Then i tried the network administrator and there I noticed something unusual. There are two options in the devices eth0 and eth1 thats ok but the unusual; thing is that the Activate (green button), Deactivate (red button) and even the delete buttons are in the background and I cannot select them. Isthis the problem for the network connectivity.
iam install ubuntu 9.10 i want to connect my bsnl broadband internet
View 3 Replies View Relatedprobably I have screwed myself. I tried to preupgrade to f14 and cancel it after some time. Now, I am facing a problem that I cannot access internet from mobile broadband; but I can access net while i am connected via ethernet or wireless. I have cleared preupgrade files with
Quote:
yum clean all; yum remove @preupgrade
It can detect my HUawei modem and creating an IP as well. But no Internet.
I am having broadband connection, I need to connect broadband internet through eth0. Please give me some use full information for configuring this.
View 6 Replies View RelatedI am using WINDOWS 7, in which i connect to the internet through broadband connection dialer wich requires username and password,aslo i have another connection wich is used to connect to LAN. I hav recently installed ubuntu 9.10.. Now my WIRED connection is showing established..with eth1 and following are the outputs of some coomands which might help u to identify the problem..
[Code]...
I installed ubuntu 10.04 in my desktop, was working fine. connecting to the internet through linksys router. now my internet is not working, because i removed the linksys router and connected directly from the internet provider modem, Motorola sbv5222 broadband modem. Now my internet is not working.
View 4 Replies View RelatedDoes anybody use successfully a broadband internet service on Fedora 10? I'm seriously thinking of buying a wireless card but don't know if it will be compatible.
View 7 Replies View RelatedI have a 2 machine LAN with both machines having an ethernet card and a wireless card. There is a Netgear router, both eth and WiFi, allowing both machines to access the internet.
On my Linux machine I am looking for some software that allows me to keep track of my broadband usage on that machine, excluding traffic between the two machines.
There are numerous such programmes for this in XP, which use Winpcap and a GUI frontend. The "other" machine on my LAN is XP and uses just such a program.
I tried to preupgrade to f14 and cancel it after some time. Now, I am facing a problem that I cannot access internet from mobile broadband; but I can access net while i am connected via ethernet or wireless. I have cleared preupgrade files with
Quote: yum clean all; yum remove @preupgrade
$ uname -rs Linux 2.6.34.7-56.fc13.i686.PAE
It can detect my HUawei modem and creating an IP as well. But no Internet. Can you tell me the reason?
We finally got internet in our apartment in China, but my husband was the only one home when the guy came to set it up (on his windows machine).
He connects by plugging in, then clicking a desktop icon labeled "Broadband Connection" where a box pops up with a username, a password box, and some buttons, one of which says "connect".
I am trying to figure out how to set this up on my netbook so that I can use the internet at home too. I have a feeling that even if I had been home when the setup guy came, he wouldn't have had a clue what to do with mine anyway.
On the WinXP machine: Connection Properties state that this is a PPPoE connection, with TCP/IP, QoS, and Deterministic Network Enhancer all checked. Under the security tab, unsecured passwords are allowed.
just downloaded ubuntu 10.10 and burnt it to a bootable cd. did a clean install works fine. how do i get three prepaid mobile broadband to work???
View 4 Replies View RelatedI'm planning to buy a mobile dongle from 3 (this one: [URL]) but I don't want to tie myself down to a contract before I'm sure that it'll work.
I have a 64-bit computer with Ubuntu 10.10 and WINE installed, so if I was to buy it, how would I set it up?
Since my recent re-conversion into Ubuntu, I noticed Network-Manager now has mobile broadband support out of the box. Splendid!
I've been using my Huawei (Vodafone) modem since around two weeks, and so far it's been great, except for a little detail: sometimes, them modem simply won't work. I plug it in, "cd" drive (where the Vodafone Mobile Connect files are) shows up, but no "Vodafone" on Network-Manager.
I believe this has something to do with settings the modem may leave behind after each use, but I'm quite newb, so.
In Fedora 14 (kernel 2.6.35.10-74.fc14.i686) I am not able to get an internet connection on my laptop via mobile broadband. However dialing succeeds and the provider starts the daily flate rate accounting.I tried the graphical network management as well as wvdial and even sakis3g (achitecture free variant from URl...).With wvdial (well configured I think) and sakis3g the dial connection is established (permanent blue light on Huawei E169). "netstat -ie" shows that the network configuration has changed (device pp0 instead of eth0 and "netstat -rn" shows that default router is set to 10.64.64.64). But "ping" does not receive data from any internet IP address and browser cannot render any website. A later check call of my prepaid balance said that the daily rate countdown was initiated (so I pay for nothing).
The GUI of the KDE network icon seems to work similar but does not set the usb key into the connected state (only blinking blue light and break-off after a few seconds).Disabling of selinux didn't change anything as well.With Mandriva 2010 I didn't have any problems with same mobile key and provider.
I'm using RedHat Linux. In my friend system have Winxp. I have 2 LAN Cards. I'm using wired Broadband internet. So i want to share my internet connection to my friend system through another one LAN card. How can i do this
View 2 Replies View RelatedSo here's the thing: I have a mobile broadband pcmcia card that worked just well on jaunty, but as I installed karmic it doesn't work, coz it mounts the card's storage but doesn't recognize the hardware. The help says I need the package 'udev-extras', but there's no such package for karmic and the one for jaunty doesn't work with karmic.
View 4 Replies View RelatedI have a little bit of a prediciment with my Mobile Broadband dongle, even though I know I'm in a 3G area (Dongle Supports 3G connection) my internet still loads at the normal GPRS speeds max of 5kb/s. Is there anyway to change the speed of it or do I have to keep with GPRS at the moment?
View 2 Replies View RelatedI am using tata indicom photon+ for mobile broadband internet connection.
Code:
Befor yesterday, I was able to connect via this, but today(i guess a update yesterday is the culprit) i cannot. while it should connect automatically, even usb_modeswitch cannot detect anything.
Quote:
my /etc/modeprobe.conf is also blank. But I can work with wireless
How to set up for broadband Internet on ubuntu on lenovo.my video n audio player of ubuntu is not working.
View 4 Replies View RelatedIs it possible to share an internet connection established on ubuntu 10.10 through a mobile broadband account with other users on a LAN network? I have my Ubuntu machine running 10.10 with the USB modem plugged into it and connected. I then also have a LAN network cable connected to a router.
View 1 Replies View RelatedHow to connect wired broadband internet with ip in Linux 'ubuntu'
View 2 Replies View RelatedI recently install Fedora 14 with dual boot Win7 on my HP G62-453TU Laptop. So, I want to use internet via CDMSA - EV-DO Rev A USB wireless Broadband internet on Fedora 14. So, i looking forward help from in this regard from Linux Geeks.
USB Vendor name : www.huawei.com
Operator : www.worldcall.net.pk/wirelessbroadband.html