Is anyone having problems since they updated? My card was working fine before I updated. Now it detects all the networks, including mine. However, when it tries to connect it sits there for ~2 minutes, then says it's disconnected. I've checked my security settings and they are fine.
View 2 RepliesWell, I have an issue with my wireless card in Ubuntu 10.04, my wireless card model is:
the D-Link WIRELESS N 150 DESKTOP ADAPTER DWA-525. I was already successful getting it to work by using the RaLink driver suggested here and following the instructions in their readme.But after a system update I performed through Update Manager (in which I guess the kernel was updated), the device stopped working completely. The wireless icon remains(in the top panel), but it displays a red exclamation mark next to it
recently installed 10.04 on his hp pavilion laptop and we got everything working fine, including the wireless internet. When he installed some recommended software updates his card is no longer being detected although wired networking is still fine.
ryan@ryan-laptop:~$ sudo lshw -c network
[sudo] password for ryan:
*-network:0 UNCLAIMED
[code]...
my cisco wireless card model # wmp600n. Fedora doesn't even recognize that its there and i haven't been able to find any linux drivers for it, tried installing the driver using wine but still isnt working for me...
View 2 Replies View RelatedI have Debian 5.0.3 and I've had a lot of trouble installing Linsys WMP600N PCI card - Ralink chipset - 2860. I had it installed in the board, before I installed/compiled Debian. What I'm thinking I should have done was chosen Desktop and Laptop during the guided install. I tried expert install, but I was over-whelmed with options. Anyways, I tried NDISwrapper in many different ways. My last tries showed that the driver and device was working. No matter what I did, I would never get an interface with a wireless extension. I couldn't find any useful information anywhere, including Ubuntu forums - I'm sure you think I'm stupid or evil.
I eventually figured I would get the drivers directly from Ralink website. [URL] The one that looked like it would work (RT2860PCI/mPCI/CB/PCIe(RT2760/RT2790/RT2860/RT2890) would error out when I would try to extract anything. I used 2nd one (RT2860WebUI) which worked. If anyone does use it, be sure to read all documentation that is included, including the README. After I was done installing/compiling it, I got ra0 interface and could see my router.
I couldn't connect to it because I use WPA2 and that wasn't an option for encryption. I will work on that later. I wanted to share this information with anyone who might need this.
/sbin/lspci reports this: 01:00.0 Network controller: RaLink RT2800 802.11n PCI iwconfig reports nothing Network manager doesn't see it. The card works when I run it from Win 7. I tried rt2800 and rt2860. no results I am fairly new to Linux and I don't know all of the command line functions, How to get my wireless PCI card detected. After I installed the rt2860 driver, I didn't reboot. After rebooting, the card lit up and now I am functional. Woo Hoo.
View 1 Replies View Relatedi have just installed 10.10 under wubi, first time trying to use this network card under ubuntu. works fine on XP where it connects with good signal strength to a zyxel p-600 b/g router (my 3 other machines also connect fine to this router)
i am using WPA2, it takes 30secs to 1min to connect in the first place, then runs slowly and with intermittent disconnects, reports good signal strength in network manager.
i have been fortunate enough to have 3 machines that run ubuntu flawlessly out of the box..
I have installed Fedora 12 OS which is using kernel 2.6.32.11-99.fc12.x86_64. I am using a Linksys WMP600N Wireless-N PCI Adapter with Dual Band card which has a Ralink chipset. I have installed the latest rt2860 driver which uses the 2.6.32.11-99.fc12.x86_64 kernel. If there is any other pieces of information that is need I can provide it.
Problem: I can use either the Ethernet connection which is built into my ABIT mother board or my PCI wireless card. My Ethernet connection works perfectly however; my wireless card comes up attaches to my wireless router; that's it. There is a strong signal, the WPA2 security password works correctly. I am able to ping my loop-back address and my DHCP IP address for my wireless card but I can not ping the router or anything outside of my box.
If I let the ping program run for a while and allow it to try to ping the router, after a period of time ~5minutes or so I will get several hits and then stop. The firewall does not change from my Ethernet connection to my wireless connection. The Wireless connection is a trusted interface in my firewall specifications. Questions/Thoughts:
Can I use the same OS provided routing table for my Ethernet connection for my wireless connection? Would the OS know which port to use by switching to a wireless connection (after reboot)? Do I need to somehow switch or bridge the port? Is the wpa_supplicant playing with my connection and opening it up and then shutting it down? Below are some netstat data: routing, interface table, statistics, and dmesg on the kernel driver rt2860.
[Code]....
I had an Ubuntu Server 32 bit installation and everything was working fine. Now that I installed Ubuntu Server 64bit on a new drive in the same machine, the ethernet card is not working!! This is insane cause when I put the hard disk with the 32bit installation back and booting from it, the ethernet card is working without any problems but in the 64bits installation it is not shown at all using "ifconfig -a"
lspci output:
Quote:
02:00.0 Ethernet controller: Atheros Communications AR8151 v1.0 Gigabit Ethernet (rev c0)
How can I check which module is being loaded in the 32bits installation to try to load it manually in the 64 bits installation?
As the title says i updated my system which then needed a reboot. I also installed Mixxx djing software to try it out. So i thought id just restart the system. Usually when i boot into my desktop wireless automatically can connect to my router but not this time, wired only for now... i know theres tons of wireless issue threads but some more experienced users will be able to get straight to the point and run through some diagnostics with me.
View 1 Replies View RelatedI have been looking around the forums searching for similar problems, it seems not only me had this problem. About a month ago I did a regular update via Upd Manager. The next day - no wired connection.Still managable, since the local library has wireless. Now that won't work either.Just after I upgraded from Jaunty, I accidentally removed NetwMngr from the top right corner of the screen, but that should not have anything to do with how the program works, right? I now cannot reach NM, if I run it from the terminal, nothing happens visibly.
View 5 Replies View RelatedI've installed 10.04 on a Dell 1200 laptop and cannot get the wireless card working. I've tried getting Ndiswrapper but it doesn't appear to be available on 10.04, and since I don't have an Internet connection, I can't download it. The card is a Broadcom Corp BCM4306 802.11 b/g. How do I get the card connecting to my Linsksys?
View 7 Replies View RelatedI'm a new user of Ubuntu and I think I need some help but let me mention before that I got this up working on a Debian system.My current kernel version is $ uname -r 2.6.32-27-generic.The problem is that my wlan card is not working any more such that my system freezes every time I enable networking with the hardware switch on my laptop.Therefore I bought a USB - WLAN stick and try to get this working.
Network Manager has the option "enable wireless" greyed out if I disable the hardware switch.If I enable the hardware switch and remove the module of my wlan CARD before (modprobe -r iwl3945) it says "wireless disconnected" for all networks.
The wired lan card on hp 530 is not working the wireless works.
Code:
I have BroadCom BCM4318 802.11B/G Wireless Card. When I first started Ubuntu a week ago it didn't work, but I fixed it after a day or two of googling it. However I made a mistake and uninstalled the Network Manager. I then reinstalled Ubuntu, but it wouldn't load the card again. I activated the driver, and restarted the computer, but then, since It was connected via Ethernet, it wouldn't reconize the Ethernet connection, but the wireless card it did, but wouldn't find a network that is supported.
View 6 Replies View Relatedi was wondering how to get the above wifi card working as it is not supported.
View 1 Replies View RelatedI have been trying to get my Trendnet TEW-649UB wireless card to work on Karmic. I have ndiswrapper "installed", but it doesn't seem to be working. I have reinstalled ndiswrapper-utils 1.9 and ndiswrapper-common from synaptic, but not ndisgtk (the GUI for ndiswrapper). When I try to see if any drivers are installed using terminal (ndiswrapper -i) the terminal freezes on me.
Previously I tried using the help doc for installing Trendnet wireless drivers, but I was met with no success. After my first try using the help doc it seemed that ndiswrapper was working correctly and the driver was installed, but when I tried to connect to my network my wireless was listed as "device not managed". If this helps at all the current state of my /etc/network/interfaces is: auto lo iface lo inet loopback
auto wlan0
iface wlan0 inet dhcp
When I run iwconfig I get:
lo no wireless extensions.
eth0 no wireless extensions.
pan0 no wireless extensions.
but when I try to install the driver using ndiswrapper -i I get the message: driver net8192su is already installed Right now my computer is not even reading that the wireless card is avaliable. When I left click on the network icon I can only see that I am on a wired network {ifupdown (wlan0)}. My computer is dual booted with Vista and the card works there, but for some reason I am having trouble with Ubuntu.
I have to connect to my university's network. I was using ethernet through our router, but now I cannot do that. I recently installed the TRENDnet TEW-643PI and it works perfectly on the Windows 7 partition. Is there anyway to get the card working on Ubuntu without being connected to the internet?
View 2 Replies View RelatedI've just installed Ubuntu (Koala) on an old (but worthy) Toshiba laptop. It's got a Sitecom WL-140 wireless card. (BTW I'm new to Ubuntu, but an old hand at Solaris). Can't get the card to work, although I think It's nearly there. nm-tool shows driver is p54pci. The activity light shows an orange light occasionally. State is disconnected. I'm not really sure whether I should be using the supplied driver (p54pci) or the Windows driver for this card and ndiswrapper. I've installed the Windows driver with ndiswrapper thinking this may fix it but no.
ndiswrapper -l says wlancig: driver installed and device (1260:3886) present.
I have a D-Link Air DWL-520 wireless card on my desktop computer. It runs well with Windows, but doesn't seem to work with Ubuntu. I am using Lucid Beta 2. I have tried googling, but have not come across any clear solutions on how to make it work.
View 1 Replies View RelatedAfter upgrading to the latest Ubuntu, my wireless card stopped working. I keep on pressing the button but the little orange light wont come on...I have an aspire 5517 with "Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)" I have tried drpjkurian's tutorial for madwifi with no success . (http://ubuntuforums.org/showthread.php?t=1309072
View 2 Replies View RelatedI have just installed a generic PCI ethernet card into a fairly low powered system (Celeron 766MHZ, 512mb Ram, 40 Gb HDD, Generic sound and video). The card came with no drivers. I have since installed Ubuntu 9.10, and up to a point everything is fine and looks great. However when I connect an ethernet cable up to the PCI card (in the hope of connecting with the Internet), nothing happens. I am thinking that I need Ubuntu drivers for the PCI card ? or does Ubuntu 9.10 come with drivers and I need to go into the 'engine room' to sort it all out ?
View 1 Replies View RelatedI have a Compaq AMD64 that has ubuntu 9.04 on one HD that works great. I've installed 10.04 on a separate HD and had problems installing it. I have 10.04 running now but I can't get my wireless card to work. During installation I skipped setting up the wireless network. Now when I boot into the 10.04 partition I cannot get the nm-applet to work. I can't get it onto the task bar and I don't see it anywhere else.
I checked to see what drivers are installed, and since I have no connection with that OS I can't update or DL drivers for it. I'm pretty sure that it is because I skipped setting it up during installation. What do I need to do to get the wireless working now? I checked other threads and none seem to pertain to my situation. Since I have to log into the 9.04 partition, I can't copy/paste outputs very easily.
I've set up 10.04 Server so that I could install directly to a command line, due to the fact that Desktop was crashing during the install every time. The installation goes fine, except for the networking portion. DHCP fails every time I try it. So I set up a static IP as an alternative. Once installation completes, none of the network-oriented tools (ping, telnet) work. I've tried pinging my router and I get 'Destination Host Unknown'. This is true if I change to a DHCP oriented setup as well.
The router sees that the machine is there, as indicated by the slowly blinking connection light meaning that it's hooked up to *something* but there's no activity. Also, networking did work within Windows before I nuked it, so I know it has the ability to operate correctly. I'm at a loss, mostly due to my own newness and ignorance of how to start tackling this within this environment.
I have a Broadcom BCM4311 wireless card on my Dell D620 laptop.
Code:
09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5755M Gigabit Ethernet PCI Express (rev 02)
0c:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01)
My wireless works perfectly with my university networks. But I have problem connecting to my house router. The first time I installed Ubuntu 10.10, it connected to internet and worked well. After a restart needed by nVidia driver, my house wireless stopped working while my university wireless still works. I have tried reinstalling the driver using System/Administration/Additional Drivers and manually
Code:
sudo apt-get update
sudo apt-get --reinstall install bcmwl-kernel-source
I need some help getting my wireless card working.I have a ASUS PCE-N13 and I'm running ubuntu 10.10 AMD64.I have confirmed that the card works running under win xp.The problem I have is that it can't see any available networks.I have downloaded and compile the latest driver from ASUS rt2860sta 2.1.0.0 and added these lines to the blacklist file.
blacklist rt2800pci
blacklist rt2800usb
blacklist rt2x00lib[code]...........
Here's the dealy-o. Card is a Netgear, computer says it's a BCM43XG REV01.Card is functional but not working on my fresh Lucid install.Here's what it says:
p { margin-bottom: 0.08in; } derek@derek-laptop:~$ lspcmcia -v
Socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:00:0a.0)
Configuration:state: onready: unknown
[code]...
The on-board NIC on my machine died this morning, so I've just gone out and bought a replacement PCI card. The card has been recognised by Karmic, but it's not working. /var/log/messages says:
Code:
May 9 11:21:58 ian-desktop kernel: [ 2.082324] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
May 9 11:21:58 ian-desktop kernel: [ 2.082334] r8169 0000:04:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[Code]....
how I install the appropriate driver (noting that I have to sneakernet files across via usb stick), or any other diagnostics I should try?
I've upgraded to Maverick but now I cannot get my wireless card working. In Lucid it didn't work out of the box, but worked perfectly by wrapping the Windows driver with ndiswrapper.
I noticed when I installed Maverick that wireless is enabled in Network-Manager and it gives me the option to create a wireless network or connect to a hidden network but it's not discovering/showing any of the wireless networks in range! So it seems as though the card is being recognized but the driver isn't working fully...? I tried wrapping the windows drivers, but that didn't change the situation at all.
Details of my system:
Code:
Ubuntu 10.10
2.6.35-22-generic x86_64
[code]....
Ever since I upgraded to the new Ubuntu, I have been having problem with wireless. In the "Hardware Drivers" I come up with 2 drivers:
1) Boadcom B43 wireless driver
2) Broadcon STA wireless driver
I activated the first one, but latter noticed that the wireless was not working, so I tried installing the second and it returned this message:
Quote:
So I unactivated the first and then it disappeared leaving me with the second, and its error message.
Quote:
What should I do now?
The output for "lshw -C network":
Code:
The last few pages of /var/log/jockey.log.
Code: