I have an old geforce 6200 AGP card and I upgraded from 9.10 to 10.04 Lucid, now my video driver won't stay loaded.It says it is loaded in the hardware drivers, but no advanced graphics work, until I go into System/appearance and click extra visual effects. Then it looks for drivers and asks to keep these, I say yes and can activate Compiz effects and all is well. Until I reboot and have to start over
View 9 Replieson my old fx 5200 nvidia card, I installed the 173 driver and now when I log in to Default Ubuntu desktop with 3d enabled, like my screen will flash on and off like the panel and my awn dock turns white and then returns to desktop and repeats. You can only see the wallpaper and thats it. Useless! My desktop is virtually useless because I can't even use it. Gonna have to reinstall Ubuntu for the 5th time!
View 5 Replies View RelatedI just installed Maverick on my HP tx1000. Jockey offered me two drivers for my NVidia Go 6150. I tried the recommended one--and it seemed to be working. It had a green light next to it in Jockey, Compiz worked, etc. Then I rebooted.
Except it didn't reboot--the disk thrashed for a while, and then I was met with a black screen. I tried recovery mode and got a bash prompt...which crashed when I ran `startx'. Then I tried Failsafe X, which did work. After some experimentation, I realized it was the Nvidia driver at fault, so I tried the not-recommended one, which didn't work, and now I've disabled both of them. But isn't there a proper driver for me to use? IIRC, I was using a restricted one with Lucid, and it was working all right.
Fun fact: The day before I installed Maverick, Windows 7 randomly decided to not boot all the way. It would show the splash screen, and then hang with a black screen too. But it works in Safe Mode. And had been working fine for a while beforehand. There must be demons in my graphics card.
I've been having big problems getting 9.10 to work with a Geforce4 MX-4000 card. I know it is not a hardware problem because I've got a dual boot win xp/9.10 setup and the video card works very well under win xp. The monitor is a Samsung P2250. The issue is that the highest resolution available after installing the recommended nvidia 96 driver is 800x600, the same as that before the driver was installed. This is very frustrating because the monitor requires 1920x1080 I'm not sure whether the driver is at fault or the xorg.conf settings.
Should I try installing the nvidia site drivers? I've checked out several forum threads on xorg.conf settings but I'm really not sure how to go on this. What I need is an entry level guide to setting up xorg.conf. The manual here is not that user friendly.
I'm running Fedora 13 x64 and updated the kernel to the latest version (2.6.34.7-56 to 2.6.34.7-61). I use the proprietary nvidia drivers (currently 260.19.12) so I had to compile the kernel module against the new kernel sources and reinstall the driver. The process was apparently successful, but when I try to start X nothing happens, it's as if the computer had been suspended, my monitor acts like it isn't receiving any input. I have full runlevel 3 access, and the system seems pretty much fine up to that point. Nvidia's own sanity tests which are built into the installer reported no problems with my driver.
View 14 Replies View RelatedI am using the akmod nvidia driver and I have the option for "sync to vblank" checked, however when running minecraft my computer is still pulling 200+ fps and it's causing tearing like a beast.Is anyone else having this problem? I don't know if my drivers are corrupted, set up improperly, or if the driver is just broken.
View 1 Replies View Relatedi just upgraded to the latest nvidia 8 series driver, i downloaded from the nvidia site. After i installed the driver, i reboot and it booted into the console login screen with no GUI. how do i get back into the GUI.
View 1 Replies View RelatedI'm using Nvidia's driver from their website and Kubuntu 8.04. I tried Debian 5.04 kde on the same computer and the resolution stays. Of course I prefer kubuntu. After shutdown the video resolution goes back to 1024x768 but I want 1280x800 instead. I have a Dell IN191ON lcd widescreen monitor and geforce fx 5200 video card. I'm using the latest video driver from Nvidia for this card version NVIDIA-Linux-x86-173.14.25-pkg1.run.
Here is my xorg.conf.
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildmeister@builder75) Wed Jan 27 03:03:53 PST 2010
Section "ServerLayout"
[Code]....
When I shut down the computer, it does not remain shut down. This is different from "restarting" the computer because when I "shutdown" the computer powers down, the fan and disks stop spinning for a second, and then everything starts again. When I "restart" the fan and disks remain spinning throughout the restart process.Further, the computer is dual booting with Windows XP Pro. If I shut down from Windows, the system remains shut down.
System Information:
Ubuntu 10.04 Lucid Lynx
kernel: 2.6.32-26-generic
[code]...
I have a problem with the radeon driver and running 3d applications (namely glxgears and google-earth). Basically the 3d application is competing to stay on top of other windows. The problem is present with all windows and balloon pop ups such as those that pop up when I click on icons in google earth; The globe will just try to get on top again and I won't be able to see what I clicked on (like the panoramio pictures).
I have had this problem with kernels huge-smp of slackware13.1, custom on 2.6.33.4 kernel, and custom 26.35.4 and 2.6.35.7 kernels. My kernel config stuff (related to radeon) are:
[Code]....
Fedora (2.6.34.6-47.fc13.x86_64) I installed that update, during the installation process it said that it had to remove three packages, one of them was kmod nvidia for the old kernel (Fedora (2.6.33.8-149.fc13.x86_64))After the update finished installing the new kernel, I restarted the system and Nvidia did not load. (I assume because Update manager removed the old nvidia? But I also assumed that a new version would be installed automatically?)I received the following Boot messages:
Code:
Entering non-interactive startup
Starting monitoring for VG vg_user1: 3 logical volume(s) in volume group "vg_user1" monitored
[code]....
I'm confused, if Update Manager removed kmod nvidia, then why does yum say it is installed? And why doesn't the new kernel update work with that version? Or should I install a driver version for that particular kernel? I've read while searching that I need to install a kmod-nvidia for that particual kernel version and that I should login to my previous kernel until that happens, is that the problem I'm having?
Why don't rpmfusion and fedoraproject release the kmod-nvidia and kernel updates at the same time to avoid problems such as this? Does anyone know how long does it usually take for rpmfusion to release the new kmod-nvidia driver for the latest kernel?
my 9.04 64 bit ubuntu machine is having some major stuttering issue, as in it can't stay on track and doesn't respond to keys at certain times, the normal flashing text bar is flashing very quickly and very eradically as well. I reinstalled ubuntu keeping my /home on a separate partition, and then upgraded to 9.10 thinking that'd fix it, it didn't.at this point i don't know what's happening, My windows partition is fine.
View 3 Replies View Relatedi installed the new beta 10.04 and it seemed right after the install and update that both nvidia hardware drivers were automatically install together. i deactivated both drivers. one driver showed the nvidia 173 driver and the other one showed "current" nvidia driver.
after a restart i then tried to activate the 173 driver. system required a restart. so i did. system booted to a black screen. i believe its at the desktop but i am unable to see it. i tried to hit esc at the boot screen to enter the grub menu but that didnt work.
I installed the latest kernel liquorix (2.6.35) but when i want to install the Nvidia driver downloaded on the Nvidia website (256.53), i have an error message because Nvidia doesn't found the kernel source tree.
I install linux-image-2.6.35-6.dmz.2-liquorix-686_2.6.35-16_i386.deb, linux-headers-2.6.35-6.dmz.2-liquorix-686_2.6.35-16_i386.deb and build-essential. I don't understand why the installation doesn't works.
I could easily go to ms system monitor display by clicking on background of desktop and finding it through there to change settings related to desktop. I want to be able to watch a movie without the desktop screen saver thing going off. where can extend it to longer than 2-3 minutes on linux mint?
View 8 Replies View RelatedOnly about 1.5 weeks into Linux guys so bear with me. I'm trying to uninstall the Nouveau driver and install NVIDIA-Linux-x86-71.86.14-pkg1.run for my old Nvidia TNT2 card. Following these directions I run into a problem in the first step. When I execute the Ctrl+Alt+F1 command and get:
Ubuntu 10.10 splat-desktop tty1 splat-desktop login: if I enter splat which I believe is my username and the correct p/w I get an incorrect login response.
The freeze's on my machine only appears when i monitor the temperature of
the gpu. Normally i use gkrellm to monitor temperatures including the gpu temperature. When i stop gkrellm there a no more freeze's on my system. Then i started nvdock which also monitor the gpu temperature and the freeze's are back. Stopping nvdock make the system working normally. I have done a few reboots now, warm and also cold starts und everything works normal.
System data: AMD P2 X4 940, Nvidia GTS 250, openSUSE 11.3, Nvidiadriver 256.44,
Gigabyte Mainboard GA-MA78G-DS3H rev.2,8GB RAM, KDE 4.4.95,
Does somebody know if the NVIDIA driver from NVIDIA repository supports Cuda?
View 2 Replies View RelatedI am experiencing the following issue. After enabling SLI and PhysX in windows vista, my dual boot fedora 10 does not see the NVIDIA driver.
Doing: cat /proc/drivers/nvidia/0 I get? in the VGA bios for both cards.
I disabled both SLI and PhysX in vista, but the problem persists. I powerdown and unplugged the rig for several hours without results.
Here are my specs:
CPU: Intel Q9300
Board: MSI P7N Diamond
CARD0: EVGA Gforce 8800 GTS
CARD1: EVGA Gforce 8800 GTS
RAM : 4 Gbytes OCZ gold PC6400 (4 x 1 Gbytes)
PSU : Thermaltake SLI ready 850 W
It is important to mention that initially Fedora did see the cards and I was able to set up a dual monitor system. It right was after I enable SLI and PhysX and re-booting into Linux that the problem showed up.
I have seen this issue before in another machine with an ASUS board, but not until today I associated with the SLI setup. My guess is that there has to be something that the driver is enabling in the cards that messes up the interface between the nvidia.ko module and the kernel, but I don't know what may fix it. I need this system for some numerical calculations.
Can do nothing with the PC. New install of 10.04 and was prompted to install Nvidia driver. Did so. Rebooted, now have nothing except a thin line at top of screen. How can I remove this driver when I see nothing?
View 2 Replies View RelatedI am trying to get Debian 6 to work on an hp Z400 - the problem is that it came with a NVIDIA Quadro NVS 295 graphics card; there may be a driver for Linux, but it doesn't matter, because GRUB insists on switching to some sort of graphics mode and the screen just blanks and switches itself off. Is there any way to make sure during installation that GRUB gets configured to stay in character mode only?
View 6 Replies View RelatedThere is one thing missing (I think) a clear guide to clearing out Nvidia and replacing it with nouveau. For all but hardened gamers, nouveau on 11.4 delivers. It also removes one more barrier to what I think is the intended goad of Tumbleweed.The problem IMHO is not that there are no clear guides. The problem is there are too many. No sooner does one person do a guide (that is clear) and someone else who does not like some point writes another guide that they think is more clear (but in fact is less clear in other aspects). And this goes on ad infinitum.IMHO we have too many guides - many of which are sufficient clear ... but the VAST number only serves to confuse users more.
Having typed that, IMHO this is NOT a Tumbleweed specific issue, but its MUCH WIDER in scope and hence does not belong as a discussion in this Tumbleweed thread.
Currently using Nvidia driver version 195.36.31, it's the version that works with Nvidia-kernel-dkms, would updating Nvidia driver to the current 275.09.07 driver version break my setup?
View 3 Replies View RelatedHow do I check if I'm using the Nouveu driver or the Nvidia Binary driver? I thought things were running nicely with the free driver because I had compositing working on my dismal graphics card... But scrolling in firefox is slow/laggy so I tried installing the binary driver with 1click install. But I restarted and still have the same problem. I think I might still be using the nouveu driver? Actually, scratch that last sentence. I just did lspci -v and got this output:
Code:
01:00.0 VGA compatible controller: nVidia Corporation NV37GL [Quadro FX 330/GeForce PCX 5300] (rev a2) (prog-if 00 [VGA controller])
Subsystem: Giga-byte Technology Device 310e
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at f0000000 (32-bit, non-prefetchable) [size=16M]
Memory at e0000000 (32-bit, prefetchable) [size=256M]
[Code]...
install debian 6 on my pc and have big problem with videoadapter driver i cannot install driver i dowload driver from nvidia do something in google but nothing! palit gtx 460 linux debian 6 x64.
View 3 Replies View RelatedNo wireless networking. The ethernet works fine, and the wireless interface itself works well in Windows 7 (dual boot). Tried: Ndiswrapper, notoriously quirky, does not seem to work with the XP driver (the oldest driver available for the RTL8191SE). The linux driver offered on the manufacturer's website lacks any installation instructions. I have no clue how to install a linux driver. SUSE seems to have two network managers that are constantly complaining about control: Network Manager and Yast. Neither are great and I am left missing my Ubuntu.
However, my audio only seems to work on SUSE. I have tried almost every distro on this machine. Ubuntu lacked sound and wireless, Fedora played startup sounds, but would not play an mp3 or wav file (fiddling with the mixer did not help). And Fedora also lacked wireless support. PCLinuxOS, my favorite, lacked sound and wireless. Tried some oldies too. ELE, DSL, Puppy, Ubuntu Netbook remix, Vector, Browserpuppy, Crunchbang, Cruncheee (just for experimental sakes) and probably others I am not remembering. So far, installing a free linux distro has cost me 14 dvd-R's and countless hours of installing, reformatting and reinstalling. Part of me really wanted crunchbang to work, as I love the minimalism and blacked-out theme.
I need wireless network access. The wireless light remains red in Linux and pressing the key does nothing to start the device. In Windows 7 it always lights white and works perfectly. Why hasn't SUSE adopted a gui for ndiswrapper? Other distros have it. Why is my brand new laptop, which is by no means abnormal in make or configuration, not 100% supported natively by any Linux distro? I just updated to the new kernel yesterday. So I should be running the most modern operating system available. Yet good-ol Windows 7 is my only fully functional environment.
I`am trying to install drivers for a very old graphics card GeForce2 GTS/Pro on Suse 11.2. I downloaded driver NVIDIA-Linux-x86-71.86.13-pkg1.run and install it successfully. But when I launch "sax2 -r -m 0=nvidia" it crushes with error "isax: could not import file: /var/cache/sax/files/config at /usr/sbin/isax line 199"
[Code]....
I've tried linux many times in the past, and I'm always irritated to the point of formatting it, shredding the disk, and cursing it while enjoying my windows. Anyhow, (for some reason beyond me) I'm trying it again. Let me start off with the fact that I am very very irritated with how difficult this is becoming (why the hell can't nvidia just make a driver I can install without all of this crap?). OK, so I know how to cd to a directory, login as root. Any time I try to install the nvidia driver, it tells me I need to close X. I've tried going into the recovery terminal and it tells me this. I've also tried the command "/etc/init.d/gdm stop" and then it just takes me to a black screen.I can't do anything from there but push ctrl+alt+delete to restart.So,if anyone can give me simple steps that would be great. I don't want to learn how to use the OS, I just want to install this driver so I can read text and more than half of my monitor is displayed on,I'm on linux hardy heron 8.04
View 9 Replies View RelatedA few days ago I installed 10.04 Lucid beta-2 and it came up OK. I then chose the recommended Nvidia driver "version current", which caused my system to come up in low graphics mode. I removed the driver and the system came up with no X11. I gave up.Yesterday I installed again, hoping that newer updates would fix the problem. The boot is now OK with no proprietary driver activated and all updates installed as of now (April 14, 05:30 GMT).
The Hardware Drivers dialog shows two choices: Nvidia version 173 and "version current (recommended)". Both of these show the status "this driver is activated but not currently in use". The only option offered is the button "remove".
I just installed Ubuntu 10.04 RC, and only basic graphics work.I have Nvidia GeForce 9600 GT. I cant enable desktop effects, nor can i watch video or anything else. Is there a way to install nvidia driver in RC? It looks and feels real nice i wish i can start using it right now.
View 9 Replies View Related