Ubuntu Multimedia :: No Sound On Newly Built Machine
Feb 8, 2011
So Im having problems getting sound to work on my new machine. I dont know if its a hardware problem or if its something else. Im kinda a linux amateur but have been using it for a couple years off and on. Im running
Ubuntu 10.10
Biostar N68s+ mother board
AMD athlon 64 x2 dual core processor
my video card is a MSI N8400GS.
Im using a DVI to HDMI cord and running it into my flat screen TV for my monitor. I normally just used a analog splitter from the back of the pc to the tv for my sound to work. Never had a problem before I had this machine put together.
I have just built a new machine and want to transfer my hard drive over to it, can i just plug it in and power up?, will ubuntu 10.04 detect the new hardware and reconfigure. if not whats the best way to backup the data and re-install.
I installed Skype onto my Toshiba Satellite running Karmic last December, and gave it a very successful test run. However, while video still works, and I can receive audio, the microphone does not pick up any sound. I don't think it could be a hardware issue- it worked so recently and my machine has experienced no tramatic events since, but I can't pick up any sound using Sound Recorder either. How could I go about diagnosing and fixing this problem?
I have already installed my sound card. aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA Intel], device 0: ALC272X Analog [ALC272X Analog] Subdevices: 0/1 Subdevice #0: subdevice #0
Followed through this: sudo gedit /etc/modprobe.d/alsa-base.conf And added options snd-hda-intel model=auto position_fix=0
After all of this, the built-in mic still doesn't work. I'm using a Aspire One 532h-2588 laptop. I need to get this working so I can use VOIP. I'm using ZoIper.
i've not been able to find a solution to my issue. I have a Gateway Profile 5 All-in-One with built in speakers. Just finished a fresh install to 9.10 and all updates. I can hear sound through the headphone jack via headphones, but the internal speakers will not play anything. I've checked the volume controls, alsamixer, etc.
My friend has following configuration Pentium 4 2.4 Ghz 256 MB DDR RAM Western Digital WD1600AVJS-63WNA0 hard disk PM8M-VHMS7104 VER 3.0 motherboard The motherboard has Realtek sound card built in but there is no sound output. He is using Ubuntu 9.10.
Somehow I cannot get sound on my newly installed opensuse 11.3, KDE 64 bit..I tried the sound panel and it looks allright. I also followed the multimedia guide an installed packman repositiry and vlc, - i might have done it wrong?
I am trying to use the ksctp on CentOS 5 newly installed machine. However, I am not able to find some files (/usr/include/netinet/sctp/h, libsctp.so etc.,) that are required for compiling my application.
Been doing a bit of reading about multimedia and poking around. This is for a new machine built from parts. Motherboard is an Asus M4A87TD with integrated sound.
Here are the results of some tests. The sheer volume of sound related kernels blows me away (lsmod).
command: aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SB [HDA ATI SB], device 0: HDA Generic [HDA Generic] Subdevices: 1/1 Subdevice #0: subdevice #0
I don't have any sound in my machine. I am using Ubuntu 10.04. I tried to remove pulseaudio ad re-install it.. after that sound icon is missing from top panel.
i found ubuntu 904 can work on my old computer machine with a built in ati display card.updating as it return a message saying that the repository may not be available..
I am using VLC to capture video from my webcam. So to set the video device I use /dev/video0 (built in webcam), but I need to specify the path to the built in mic and I can't find what that path is. If it help any, it seem my system is configured to use pulse audio instead of alsa. Is there any script to run to find where my mic is "pathed" at? arecord -l returns this:
$ arecord -l **** List of CAPTURE Hardware Devices **** card 0: Intel [HDA Intel], device 0: ALC883 Analog [ALC883 Analog] Subdevices: 1/1
(1) I'm wondering if there is a way to have abcde play the songs while it is encoding? I understand that this would be a lot slower.
(2) Is it possible to have abcde start playing right after it finishes ripping the first track and then have it add on the other tracks to the playlist as it rips them.
Is there anyway to do one or both of these from the command line or with abcde's built-in options?
I also posted this as a question in launchpad, but wasn't sure if this might be a better place. Pretty new to Ubuntu, if you couldn't tell.I just upgraded from 9.04 to 9.10 and cheese/skype don't see the webcam built into my machine. It worked with Windows 7 that came with the computer, and in 9.04. I'm using a Asus 1005PE.
result from lsusb: Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
I have a ASUS K52J.I tried cheese.It was initially upside down. Then I tried Video for linux device preferences.When I checked vertival flip, that fixed cheese. But it was still upside down in skype.I tried downloading skype from the webpage, and from synaptic.I tried running skype in sudo.I tried: export LIBV4LCONTROL_FLAGS=3 && L
D_PRELOAD=/usr/lib32/libv4l/v4l1compat.so skype but i get: ERROR: ld.so: object '/usr/lib32/libv4l/v4l1compat.so' from LD_PRELOAD cannot be preloaded: ignored
and I tried: export LIBV4LCONTROL_FLAGS=3 && LD_PRELOAD=/usr/libv4l/v4l1compat.so skype ERROR: ld.so: object '/usr/libv4l/v4l1compat.so' from LD_PRELOAD cannot be preloaded: ignored.I tried this:
LD_PRELOAD=/usr/lib32/libv4l/v4l1compat.so skype When skype loads up, i go to the options>video>test. The green light comes on by the built in webcam, then i get a segmentation fault and skype crashes: /usr/local/bin/skype: line 2:4055 Segmentation fault LD_PRELOAD=/usr/lib/libv4l/v4l1compat.so /usr/bin/skype
Then I tried:LD_PRELOAD=/usr/lib/libv4l/v4l1compat.so then running skype and i got the segmentation fault again.I may have missed some threads on this but everyone else seemed to be thanking someone for fixing their problem by now.Finally I tried threating my computer with a Windows installation. But I think both me and the computer knew it was a hollow threat,
I just bought a new graphics card and installed it. it works perfectly although my sound worked perfectly this morning and I think the graphics card is overriding my built in sound card. I need help fixing the sound. The graphics card I bought is an ATI Radeon Cedar HD 5450 The sound I want to use is HDA VIA VT82xx when I run alsamixer I get Card:
There is no audio output to the speakers when listening to, or while recording from Line-in. Enabling software sound playthrough in Audacity did not help. Audacity simply froze. But I can make fine recordings from Line-in and play the recorded files. Also no sound from cd-audio. KsCD begins playback, but no sound. Only VLC works with cd-audio. Maybe some slider settings that I missed? This is what I did so far: Advanced Linux Sound Architecture Driver Version 1.0.20
New eeePC 1015PEM netbook, 2GB RAM, 250GB HDD. Came with Win 7 Starter; I retained this and installed openSUSE 11.3 alongside. Everything works well in Win 7 Most things also work well in oS 11.3, but there is a knotty problem with audio from the built-in speakers. Headphones are OK, but the speakers don't work reliably. Others have reported this on similar machines, and a number of "fixes" have been proposed in a wide range of forums, but so far I haven't found any that work.
I've actually installed oS 11.3 twice. After the first install I had no speaker sound at all, but after a day or two fiddling around it started to work of its own accord for no reason I could point to. For unrelated reasons (a silly mistake by me in Win 7) I then had to re-install oS 11.3 from scratch. This time the speaker sound worked after install, but then it dropped out again a couple of days later. Headphone audio has remained OK throughout.
I'm aware of and have applied the acpi_osi=Linux kernel parameter to enable the Fn keys on the machine (including sound volume and mute/unmute), so it's not that. I've combed the forums and Google extensively for other suggestions, and have tried them - including installing alsamixergui. I've also installed a properly matched ALSA KMP which changed some of the alsamixer controls but didn't cure the problem. Since it all works very well in Win7 and works sometimes in oS 11.3, I conclude that the problem is not with hardware but is something in software.
I have been using Ubuntu as my main OS on my desktops for a couple of years now. Started off with a HP with a Creative Labs XiFi soundcard, but am now using a Dell with a Creative Labs Audigy. Sound worked perfectly on the Dell since a clean install (about 7 months ago). I turned it on a week or so ago, and no sound! Even the little sound indicator in the notification area has gone.
After installing I was not able to get many of the audio programmes to work. After some reading, I realised that this was probably due to jack not starting.
I was unable to get jack to start normally but have been able to get it started with the playback only option selected. Programmes that use jack now work, however there is no sound once jack has been started. The sound does work in other programs when jack is not started. Strangely, I only have to open qjackctl for the sound to stop, and jack is not even started. Initially I thought these problems were due to my sound card not being supported, but I believe that alsa support was added for the via 1708 codec at some point. I found that support had been added in a document showing the changes between alsa versions; however I cannot find the exact model listed as a supported sound card on the alsa site.
I believe that altering jack settings could fix the problem, as i have been able to get audio to work in hydrogen by selecting plughw:0 but there is still no sound in other programs. I have tried altering many other settings but to no avail, however I do not really understand the meaning of the settings that i am adjusting.
Does anyone know what settings to adjust or know something else that might fix this problem so that sound works once jack has been started?
Also, would programmes that use jack such as audacity, hydrogen, and ardour work with pulseaudio as the main sound server if I were to install normal ubuntu - it might be worth seeing if my soundcard works with the puleaudio sound server
if this helps, here is the error message received when jack does not start when the normal duplex option is selected.
21:24:04.867 Patchbay deactivated. 21:24:04.868 Statistics reset. 21:24:04.886 ALSA connection change. Cannot connect to server socket err = Connection refused
[Code].....
also, when i open alsamixer in the terminal for some reason the headphone part is greyed out, even when the sound is working before qjackctl is opened.
I've got a custom compiled kernel, just built on Lucid 10.04 from the kernel sources.System works fine, except for sound.When I log in as normal user and try to play a wav file using.The sound file is being played, but I hear no sound.However, when I do "sudo -s" and become root, execute the same mplayer command then I can hear the sound.My Sound preferences shows no input device and only "Dummy Output" as output device.On the generic kernel as came with the Lucid 10.04 CD, sound preferences shows different devices.The strange thing is: when I compiled my custom kernel, I changed nothing to the sound options in the kernel config file.
I have no sound, is it possible to restore the default sound drivers/settings in 10.04?It was work well before except for one issue, I couldn't get mic in for Rosetta Stone using wine. I have followed so many howto's to try and get Rosetta Stone working and then my sound working again.I think this is my main problem I upgraded alsa to "alsa-driver-1.0.23". I could easily be wrong about that assumption though.I have a Dell XPS M1210Ubuntu 10.04 64bitI think this is my sound card, "lspci -v | less"00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01)Subsystem: Dell Device 01d7Flags: bus master, fast devsel, latency 0, IRQ 11 Memory at efffc000 (64-bit, non-prefetchable) [size=16K]Capabilities: <access denied> Kernel modules: snd-hda-intelBut I don't think it is being recognized,
For a couple of days ago, maybe a week or two I beguinne to get a 'snap-sound' in my compurt sound, like an eletrick charge or someting. I comes with about a minutes period. I resently find out that it came from the center-speaker. I run Ubuntu 10.04 LTS and have this sound-card: 00:09.0 Audio device: nVidia Corporation MCP73 High Definition Audio (rev a1)
My speaker system is Logitech X-530 I have located the problem to center-speaker, but the snap-sound only disappear if I mute the center, not lower the input, in the GNOME ALSA Mixer. I have tried to disconnect the antenna to the analoge-TV-tuner. Has anyoe a similar problem, and a trick to fix it? I don't know if it's related to any recent update of the system?
Playing a song works at first; then it quits after 1-5 minutes. If you select a different output device, it will work for another 1-5 minutes, but switching back to an already used up device will not play sound. Running 'sudo killall pulseaudio' resets everything and each output device works for another 1-5 minutes. This is on on 9.10.
I have a fresh install of Natty and i'm having some issues getting sound to work. My laptop has a built in sound card which works just fine. However, i also have a usb 5.1 sound card which isn't working at all. Both devices show up in 'Sound Preferences' but when i select the 5.1 device as the output device sound doesnt work. I ran the alsa-info.sh script and the output can be found here.
I am setting up a mythtv/xmbc box on Ubuntu 10.10 (natty does not install on my hardware). I have a Sabrent TV PCIRC tuner card, which seems to work fine with the proper card and tuner settings. My on-board sound is HDA-Intel surround sound, which I have configured as analog duplex.
Currently the sound works fine through my speakers plugged into any jack on the back of the PC (two speakers, one jack). I can watch ripped movies and listen to music. The TV tuner is pumping sound from its external jack -- if I hook it up directly to the speakers it works fine. I can feed the Tuner's sound to the line-in on my motherboard, but nothing comes out. In the sound manager, i have the input device selected and the input level shows that the sound is coming in through the connector, and I can test the speakers and they work fine, but they don't seem to be communicating that the sound coming in needs to be pumped out through the speakers.
I am using a USB headset and a logitech QuickCam Pro 4000 with Ubuntu 10.04
1. When I change the sound to internal sound the webcam works in Skype but I have not sound. 2. When I change the sound to the USB headset (sound output) the webcam does not work in Skype.
