Ubuntu Multimedia :: Internet Connection And The Power Connection Icons Also Don't Appear
Jan 26, 2010
It is most certainly my fault but I am now without a sound volume control and it does not show up in the add to panel.What can I do here? Does your icon have code that that I can use or can I find the file somewhere and create a link? Alsa mixer works ok and nothing is muted and I have sound so as to play music. The Internet connection and the power connection icons also don't appear.
View 5 Replies
ADVERTISEMENT
Jul 10, 2010
Our area was hit by a power surge and I cannot get the internet connection to work? What can I do. I'm using an AT&T modem which is connected to a netgear router.
View 4 Replies
View Related
Jan 31, 2010
Sometimes either due to a power outage or due to lightning I turn off my Wimax modem and continue to use my laptop on the battery.Then when I turn the modem back on, there is no internet connection.Here's what I've tried:
1. turn off and on the network connections - right-clicking on the icon on the bar on top of my screen.
2. turn off and on the dsl-provider connection - no effect.
3. When I tried to re-do pppoeconf, it says that there's no response from the concentrator.
This has happened a few times in the past and the only thing I can do to go online again is restart the computer. And it works.Now on Windows, the double-computer icon showing a network indicates connectivity AND data movement. Unfortunately we don't have this on Ubuntu.I'm just after a restart and I'm online now. But I'd like to know if there's a way around this without having to restart.
View 3 Replies
View Related
Jan 9, 2011
I am running Ubuntu 10.10, and I would like to use my computer to share the internet connection from an ethernet port. For example, I would like to set up my computer as a wireless access point so I can create a network that other computers can connect to for internet.
View 3 Replies
View Related
Jan 24, 2010
Its a case of ".... wireless network connection active but still not internet connection .."I am using WEP - 128 key ... Works when I connect directly using ethernet cable ... but not wireless (pci and wireless router)
ubuadmin@ubucomputer:~$ ifconfig
wlan0 Link encap:Ethernet HWaddr 00:06:25:12:83:3b
inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::206:25ff:fe12:833b/64 Scope:Link[code].....
View 5 Replies
View Related
Apr 15, 2011
1 linksys router: gets the net from PPPOE and give the network DHCP. The router IP is 192.168.1.1. 1 windows laptop that work wireless and wired. 1 debian desktop that work wired and not working wireless. THe problem with the debian desktop is like this: I have a TP-Link TL-WN321G installed and found by lsusb command. I make a wireless connection WPA Personal (just like the router settings) it says i am connected to the wl network but no internet connection. the route command give me this:
[code]....
I tryed with wicd who said that the connection is WEP (and it's not, it is setup to WPA on the router and the network-manager conncetion) and when i try to connect i get bad password. I tryed with network-manager uninstalled and no chance.
View 4 Replies
View Related
Jun 25, 2010
I would like to have all traffic from the ethernet connection out through the wireless (basically using the box as a router) however I am having some trouble doing this.
I have done this before on Windows however I am having some trouble doing this on linux, I have tried using Squid Proxy however I am having some trouble using configuring/using it.
I am using Yellow Dog Linux however I am willing to change to any other distro as long as it is compatable with PS3 (as this is what im using linux on)
View 14 Replies
View Related
Jun 21, 2009
I have installed Fedora 11 recently. I want to share my Internet connection.
I have e LAN connection eth0 which is connected to internet.
I have a Wireless connection wlan0.
I want to share my internet connection with wireless connection.
View 3 Replies
View Related
Feb 4, 2010
I have two linux laptops. Currently, I'm using both of them at work, side-by-side. Now the problem is, I'm connected to a wireless router, but the wireless only works on one of the laptops. So I'm stuck with one laptop that has no access to the internet. Both machines do, however, have working ethernet nic cards. So, I was wondering if I could use the laptop with the wireless connection to share the internet connection with my other linux machine and access the internet on both of them. Or as an alternative, just use the internet on the machine without wireless and be able to switch back and forth, that would increase my productivity like 30 fold.
View 5 Replies
View Related
Jul 4, 2010
I tried to finally set-up surround sound on my Ubuntu 10.04 machine and i was successful in doing so after a while of changing settings and tinkering. After doing so though, i was later in the day not able to get into the Pulseaudio Volume Control, therefore, everything is stuck where it is and i can't change anything. When i try to open Pulseaudio Volume Control i get the error message, Connection failed, Connection refused. My programs still play sound and i can control the sound of the programs through the programs, but i cant control the sound of the sorround sound now and my main sound bar only affects my stereo speakers, not the surround ones.
I believe this may have happened after the random disk check on restart, but i can't 100% confirm that and i'm not even sure if they are related. I still have sound, but i have no way to control the volume of my entire system at once. I did some looking around online and saw that others are having or had the same issue, and it was through different versions of Linux also. somehow reset everything so i can access PAVC and start over . I also tried steps listed in another thread here on the same topic, but they weren't working and it also seemed to be for older Ubuntu versions.
[Code]....
View 9 Replies
View Related
Mar 12, 2011
I am new user for Ubuntu OS Do you have any offline installer of VLC for 10.10 for ubuntu 10.10. give link to download software allso. HOw to intstall Software without Internet connection
View 1 Replies
View Related
Oct 31, 2010
I have the "Work Offline" problem: when I boot up, the icon on the toolbar tells me I have "No network connection". This is not quite true, since I can access the first page of any website - only subsequent pages are inaccessible. I get a message saying that Firefox is offline. However, when I uncheck "Work Offline" in the File menu, it makes no difference to this behavior.
The problem is on my Ubuntu Dell desktop, which is connected to the internet with cable broadband via a D-Link router (wired connection). It has worked fine up till now. I use Ubuntu 10.04 and Firefox 3.6.11. I am writing this on my Ubuntu Dell laptop which is wired to the same router, so I assume the problem is not the router. I have tried various strategies suggested in threads on these forums, including editing about:config, changing "allow" to "deny" in some lines of /etc/dbus-1/system.d/NetworkManager.conf and changing from Automatic (DHCP) to Automatic (DHCP) Addresses only, but no luck so far. The contents of ifconfig are:
eth0
Link encap:Ethernet HWaddr 001:aa0:91:a7:51
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets: 0 errors: 0 dropped: 0 overruns: 0 carrier: 0
collisons: 0 txqueulen: 1000
RX bytes: 0 (0.0 B) TX bytes: 0 (0.0 B)
[Code]...
If I comment out "auto eth0" as well, it makes no difference. If I uncomment both lines ("auto eth0" and "iface eth0 inet dhcp") then I lose the internet connection altogether.
View 4 Replies
View Related
Jul 9, 2010
I need to setup an Ubuntu Server to handle backups over the network (probably rsync over ssh). That server will then transfer the backup data offsite over a secondary external data line.How can I configure the ethernet interfaces to handle such a scenario?
View 1 Replies
View Related
Dec 18, 2010
I'm running Ubuntu 10.10 netbook edition on a Dell Mini 9 - worked around a few wireless issues on setup and connectivity has been fine, but now I'm suddenly losing wifi when I unplug my AC adapter. It still shows me as connected, but when I try to view web pages in Chromium, it will load pages for a few seconds, and then suddenly cuts out - though it still looks like it's trying to load the page.
It's the same if I boot on battery power - it will keep trying to connect to wifi but won't until I plug in the adapter. I'm assuming this probably has something to do with my power management preferences in battery mode, but I'm still pretty new to Ubuntu, and I'm not sure how to fix this. I've played with the options in power management, but I have a feeling there has to be more. Can anyone help me? This has been really frustrating.
View 4 Replies
View Related
Mar 21, 2011
I have a problem with my wireless where when running the laptop from the battery the connection is very slow. When the laptop is connected to the power supply everything is fine, but the moment it's disconnected and run on the battery the speed drops when browsing the Internet or accessing files on other computers on my network.
The laptop is a Samsung SF310
Wireless chipset is BCM4313
Code:
02:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g LP-PHY (rev 01)
Subsystem: Wistron NeWeb Corp. Device 051a
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at f4c00000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: wl
Kernel modules: wl
In attempt to fix this I installed the latest drivers from the Broadcom site using this guide. When I enabled these drivers everything worked well. I did speed test and got the same speeds I get when connected via Ethernet:
Ping 51ms
DL 4.31
UL 0.65
So I set the drivers to load at boot using this forum post as a guide as the steps in the Broadcom guide didn't work and rebooted the laptop on battery power. The wireless connected fine, but the slow speed problem had returned. Running a speed test got the following results
Ping 235
DL 0.54
UL 0.30
So I ran iwconfig when running from battery and then from power supply.
Code:
xxxx@xxxx ~ $ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11 Access Point: Not-Associated
Link Quality:5 Signal level:215 Noise level:160
Rx invalid nwid:0 invalid crypt:0 invalid misc:0
As can be seen the signal quality is 5 and signal level 215
Code:
xxxx@xxxx ~ $ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11 Access Point: Not-Associated
Link Quality:5 Signal level:214 Noise level:164
Rx invalid nwid:0 invalid crypt:0 invalid misc:0
And when connected via the power supply the signal level is 5 and signal level 214. There may be some kind of power saving issue, although there are no relevant setting in the BIOS and I can't see anything in the various wireless control pannels. I have other wireless drivers and there are no problem with those.
View 1 Replies
View Related
May 4, 2010
I use an ADSL connection which I 'dial' using the Network Manager. My laptop is connected to the modem through an ethernet cable.
The thing is the place where I stay is prone for power failure. So the modem goes out with the power. It comes back on within a minute when the power is restored but Network Manager doesn't seem to automatically re-establish the connection after it is lost once. I have to manually do it. Hence most of my downloads do not get done.
View 6 Replies
View Related
Apr 19, 2011
I have three machines networked to my desktop which run a bunch of simulations in parallel. As they're running, I connect to them via SSH and screen to keep an eye on the runs and look at the output. They stay usually connected for days at a time. The SSH servers and client are running Fedora 14. Yesterday one of my coworkers accidentally yanked the plug on one of the servers while it was running. When I powered it up again, I started getting some odd connection problems. I couldn't connect to it via SSH initially because I got the Remote Host Identification Changed (RSA host key changed) error. I deleted the key in .ssh/known_hosts, which allowed me to connect, but it denied my password. I then logged into that machine locally, restarted sshd, and removed .ssh/known_hosts again. Now I can log in via SSH without problems. However, the connection dies with a "Write failed: Broken pipe" error every few minutes (as opposed to the other two machines, which stay connected indefinitely).
So my questions are:
1.) why would a power loss affect the behavior of the SSH server?
2.) why do I keep getting broken pipes now?
View 4 Replies
View Related
Jun 4, 2010
After upgrading to Ubuntu 10.04, I'm not able to make any connection to the internet with either my netbook through WiFi or my computer on wired LAN. I can, however, ping my Solaris machines and Macbook. How do I fix this?
View 9 Replies
View Related
Oct 21, 2010
I tried to install Xubuntu 10.10 Maverick as dual boot on my laptop. However when xubuntu is on, I can't find a way to connect to internet. When I try the 2 arrows on the up-right corner the option for wireless is deemed. I tried offline/online, that did not work either. when I click the firefox It says you are not connected.
View 1 Replies
View Related
May 1, 2011
I seem to have is trying to get the internet to work. I can go to ..... ect but when I try to run playonlinux it says you do not seem to be connected to the internet, please post if you have anything useful, as I said I am very new to linux so be as detailed as possible.
View 4 Replies
View Related
Oct 10, 2010
I setup a mythbuntu pc with an onboard card (eth0) so I could watch and listen to movies and music stored on my other pc in the basement. Everything worked fine until we had a power outage. I turned on the pc after the outage and had no networking.
I looked and saw no link lights. I verified the network port but plugging in a laptop. I got an ip and able to connect to the internet so the port is not the issue. I plugged in a pci 10/100 card (eth1) and booted up, got link lights, but no networking and not able to even ping the gateway. I setup a static ip in /etc/network/interfaces and added a route to the gateway/router. Still nothing.
View 6 Replies
View Related
Jul 5, 2011
OpenSuse 11.4 Asus Netbook 1000H Following other members in the forums I have installed Opensuse 11.4 on the Netbook. In the early days Ubuntu Netbook Remix worked well for me. But this has been discarded, and the "one size fits all" Ubuntu had become slow and cumbersome. So..... onto my post. Opensuse is working well. The install went beautifully.
It detected the Wireless Internet and I am able to get on line. I also need to share the Internet connection to a desktop. This is done via a small network switch. Thus far I cannot do this. I tried to use ifup to configure a static ip but this busted my Wireless configuration. I went back to knetwork manager. Then I tried to set up the wired network using knetwork manager and under IPV4 "share" the connection. But this blanks out any possiblity of a static address and substitutes dhcp. My desktop cannot ping the this dhcp address. Ubuntu had this thing called Firestarter? - from memory. This configured the system to sharing the network.
View 7 Replies
View Related
May 26, 2010
I have just installed ubuntu 10 on a thinkpad t410. At first everything worked swimmingly, INCLUDING the wireless. After about five minutes, the wireless stopped working, in that it seemed to think it was still connected but pinging didn't work. I've now restarted several times, and each time I restart, the wireless works for about 1 minute, then stops working. If I try to disconnect and reconnect it will not reconnect (until I restart, that is).
iwconfig shows the correct ESSID and ifconfig shows an address, and "connection information" shows a varying percentage of connection.
View 1 Replies
View Related
Feb 23, 2010
I got a dsl broadband connection....I have dual booting on my lappy(Windows7 and ubuntu 9.10)....my problem is i cannot set up the internet connection in ubuntu while i am using the connection in windows7....I am a total newbie in linux
View 3 Replies
View Related
Jan 31, 2011
I have loaded Ubuntu studio onto an older computer. Seems to work fine but I cannot get an internet connection.
View 9 Replies
View Related
Jun 6, 2011
I turned on my computer today and was unable to access the wireless, I tried to use etho but no luck either. I'm currently running 10.04 and haven't installed any updates or done anything out of the ordinary. I tried removing the internet connection from the network manager and then re adding it, but nothing working :/
View 1 Replies
View Related
Apr 3, 2011
I'm trying to create a PAN (Personal Area Network) using a laptop (Siragon ML-1040) and my desktop computer, but I get the Connection Refused (111) error.
Blueman doesn't detect any network service between the two computers unless I start PAND on one of them and then it detects the NAP service. That, only after I enable the NAP/Workgroup services on the Services submenu in Blueman. However, it doesn't work neither with the NM plugins or without them (dhclient and that other one I can't remember the name of).
Any clues over here? I'm using pand 4.91 and blueman.
View 3 Replies
View Related
Feb 10, 2011
I am running an Ubuntu Server on a VirtualBox VM running on my windows machine. So I've created a self-signed certificate using the following tutorial: [URL]
From this tutorial I'm left with 3 files:
server.key
server.csr
server.crt
Then I found this very similar tutorial that has an extra bit on installing the certificates in apache: [URL] So I followed it's instructions which boil down to this:
[Code]...
So I'm thinking this should work now. However in Chrome I get: SSL connection error Unable to make a secure connection to the server. This may be a problem with the server, or it may be requiring a client authentication certificate that you don't have. Error 107 (net::ERR_SSL_PROTOCOL_ERROR): SSL protocol error. IE8 gives me a typical "Internet Explorer cannot display the webpage" Note that [URL] fails while [URL] works fine, so it's definitely something in my ssl setup I'm thinking.
View 5 Replies
View Related
Jul 28, 2010
I'm trying to do a SSH connection between my home and work PC both machines are running ubuntu 10.04. I have read all the comunity documentation at [URL] from Work PC. I went on to the web site what is my ip address and noted down the number, From Home i opened a terminal and typed: pnig (ip address). to which their was no reply, now i'm assuming i need to configure the works router to except connection requests, is this Correct?
Also what information do i need from my works network and how do i get it? I understand that I need the routers expernal ip address, but how do i referiance a specified computer after that address? What program do i use in ubunu and how is that information applied to it?
View 4 Replies
View Related
Jun 11, 2011
My problem is exactly the same as [URL]
but I am stuck at the last hurdle
here are the output of the command that helped to solve the case in the previous post:
ifconfig wlan0
wlan0 Link encap:Ethernet HWaddr 00:1b:77:d2:59:55
inet6 addr: fe80::21b:77ff:fed2:5955/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[Code].....
I have also tried sudo dhclient but it hasn't helped and I am still unable to connect to the internet
View 1 Replies
View Related
