Ubuntu Multimedia :: Connector Not Showing For Sigmatel Stac 9200?
May 3, 2010
I have tried to ask this question before but was not posting in the right place due to my newness. I have looked hard for a solution and learned a lot over the last week. In fact enough to understand how much I don't know. I do not have a connector available to switch between line and mic inputs and would like help to set them up please.
I installed 10.04 RC to try Ubuntu and had a separate control for line and mic but now only as the screenshot. The first picture is of how I remembered my RC install and is not my original screenshot. The second is how my system is now.
My computer is a Dell Inspiron E1505
My sound card a Sigmatel stac 9200
My operating system Ubuntu Lucid 10.04 LTS
Here are some data from my system:
aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: Intel [HDA Intel], device 0: STAC92xx Analog [STAC92xx Analog]
Subdevices: 1/1
[code]....
I have added this line to /etc/modprobe.d/alsa-base.conf
options snd-hda-intel model=dell-m25
Off topic but if someone could mention it. What is the difference between "capture" and "line & mic" controls. How can I insert code into those scrollable boxes titled Code
View 2 Replies
ADVERTISEMENT
Aug 3, 2010
A friend of mine is looking for a cheap PCI graphics card to do TV-out from his PCI only PC for MythTV duties. We've found cheap old PCI Radeon 9200's with TV Out on eBay. These appear to only be supported by the open source drivers now, but will the TV out work with the open source drivers?
View 3 Replies
View Related
Jan 29, 2011
I installed Ubuntu 10.10 (although in the System->About Ubuntu is mentioned that I have Ubuntu 11.04 - the Natty Narwhal, I don't know why) and I can not make the microphone from my headset to work. I used to have the Ubuntu 8.04 (I think so) and the mic used to work normally.
Everyone proposes to change the Connector in the Sound Settings but I do not have such option (you can see the attached image). What should I do?
View 3 Replies
View Related
May 4, 2015
I have an older computer and I did a fresh install of Jessie
Procesor AMD, Graphic card ATI Radeon 9200 PRO / RV280
After instalation my computer boot into black screen. I have no problems with wheezy.
I installed manually firmware-linux-nonfree (in case) module R200_cp is loading correctly.
When I configure Xorg, my log file says something like that:
-----------------------------------------------------------------------------------
(EE) Segmentation fault at address 0x0
Fatal server error:
(EE) Caught signal 11 (Segmentation fault). Server aborting
--------------------------------------------------------------------------
View 14 Replies
View Related
Mar 6, 2010
I'm running a Dell inspiron 1501 laptop with a sigmatel stac 9200 sound chipset.
When I had ubuntu 9.04, I had sound no problem and when I upgraded to 9.10 I had sound for a little bit. Now the only way I get sound off my laptop is by plugging in my headphones.
I've tried trouble shooting this a number of ways using the following links as the latest:
http://ubuntuforums.org/showthread.php?t=614903
https://wiki.ubuntu.com/DebuggingSou.../KarmicCaveats
http://ubuntuforums.org/showthread.p...nd+head+phones
My question is...is there anyway to get sound on my laptop without having to go through headphones?
ps. I've installed and reinstalled ubuntu 9.10 and 9.04 and neither of them have sound.
View 3 Replies
View Related
Nov 5, 2010
Did anyone try to get ATI Radeon 9200 working on Maverick? For me, the DVI flickers all the time like crazy and is totally unusable.
frglx doesn't seem to support it anymore, adding Option "NoAccel" partially solved the issue
View 2 Replies
View Related
May 28, 2010
I've been meaning to get back into linux for a couple of years now.It seems I may have left it too long for my hardware.I'm struggling to freshly install lucid 10.04 onto a pc with an ATI 9200 graphics card.Can someone give a definitive answer on this - the internet is full of different solutions and I cannot get any to work.
View 9 Replies
View Related
Jun 20, 2011
I installed Tomcat (apt-get install tomcat6 tomcat6-admin tomcat6-common tomcat6-user tomcat6-docs tomcat6-examples) and it runs without problems.
I installed MySQL (apt-get install mysql-server) and it seems to run without problems too.
I changed the default JRE (update-java-alternatives -s java-6-sun).
The weird thing is - if I put the connector-jar into my web application (WEB-INF/lib), the connection works. If I put the connector-jar into usr/share/java, it does not work. If I write the jar location into the CLASSPATH and try "java com.mysql.jdbc.Driver", I get a NoSuchMethodError:Main, which means, that the jar is found?!
The datasource in the tomcat context.xml is:
<Resource name="jdbc/myresource" auth="Container" type="javax.sql.DataSource" maxActive="100" maxIdle="30" maxWait="10000" username="username" password="password" driverClassName="com.mysql.jdbc.Driver" url="jdbc:mysql://localhost:3306/myschema" />
How can I make the database connection work without putting the jar into the WEB-INF/lib folder of the web application?
View 2 Replies
View Related
Jul 15, 2009
Fully updated F11, video card sapphire radeon atlantis 9200. Xorg keeps crashing randomly and kicks me out to the F11 login screen, sometimes when I try to close a window, other times just by itself.From /var/log/messages at the exact time of the crash:
kernel: Xorg[1663]: segfault at 70c0b30 ip 049de1de sp bfaf0bac error 4 in libgcc_s-4.4.0-20090506.so.1[49bd000+2a000]
gnome-session[1831]: WARNING: Detected that screensaver has left the bus
[code]....
View 2 Replies
View Related
Mar 16, 2010
I'm trying to do a standard mod_jk setup--get apache to forward requests to Tomcat. I must admit that I'm not so familiar with the details of mod_jk, but I got this working before when I had used tomcat 6 directly from apache's website, but now that I've switched to the version in Ubuntu's repositories I can't get it working.
The log for mod_jk says:
Code:
[Mon Mar 15 23:59:41 2010] [5575:3004840816] [error] ajp_send_request::jk_ajp_common.c (1359): (ajp13_worker) connecting to backend failed. Tomcat is probably not started or is listening on the wrong port (errno=111)
[Mon Mar 15 23:59:41 2010] [5575:3004840816] [error]
[Code].....
View 1 Replies
View Related
Apr 2, 2011
I installed ubuntu 10.10 on a desktop to use for a media server, and plus some. Everything worked! I proceeded to install the nVidia driver for the 9800gt After it was installed I rebooted per the notification after installation.So now my computer loads directly into terminal and I can't start the GUI. I tried startx but it gave that whole warning about the "nopowerconnectorcheck".
So I've done my research and I bought a 650w psu. Still no dice. I know that there is a way to turn off the power connector check but I have no Idea how.
View 2 Replies
View Related
Mar 11, 2011
I changed my graphics card from Nvidia GeForce 2 MX200 (drivers I used were nouveau) to ATI Radeon 9200SE (now drivers should be radeon). Unfortunately I couldn't get X to start. It leaves me to black screen with white cursor blinking. Both cards are AGP on old Slot 1 motherboard. Reason for change was that GeForce didn't support interlacing on VGA. There are no updates installed to Debian (Squeeze), because there is no internet connection on this computer currently. I tried few things but they didn't work:
* I tried to reconfigure xserver-xorg, didn't help
* I tried to make xorg.conf with X -configure and then moved it to correct place, didn't help
* I tried radeon.modeset=0 option, but it didn't help, I had some other problems with this but I think it's not important (I'll tell later if needed)
I tested Fedora 15 Alpha XFCE LiveCD, but it didn't boot because of my CPU I guess (VIA C3 1 GHz, Nehalem core). I also tested Ubuntu 10.04 LiveCD, but it told that there was an error with radeon and low graphics mode is needed or something like that. So it was as bad as Debian. I took few logs and stuff to pastebin.
Xorg.0.log
dmesg
lspci
View 4 Replies
View Related
May 23, 2010
I just lost my weekend trying to install Xubuntu 10.04 on my pc I made the ps a while back - its built on a ASUS P4S800D-E motherboard and it has an ATI Radeon 9200 LE graphics card. It has a PS/2 keyboard and mouse, 1Gb of memory and a 160Gb PATA/IDE hard drive (I unplugged the SATA drives) Every time I installed or made a tweak to the config it failed in the same way. It showed its failure by continually repeating the first character typed. Regardless of whether this was the password screen for synaptic or just the first character typed into a terminal. Until the first character was typed the mouse seemed to work ok but then it would stall too
I've tried most things, running Xorg with/without an xorg.conf file, loading the ppa kernel and tweaking loads of bios and grub boot parameters all to no avail. So I think I want a more linux friendly graphics card and I fear I may need a new motherboard. Can someone recommend a replacement graphics card for this motherboard? Can anyone reassure me that my motherboard is ok with linux?
View 1 Replies
View Related
Jul 20, 2011
I'm using Ubuntu 11.04. I'm trying to get a Cisco Valet Connector AM10 to work. It's one of those ZeroCD USB devices that is both storage and modem. Using this link:
[URL]
I filled out usb_modeswitch like this:
Code:
# Configuration for the usb_modeswitch package, a mode switching tool for
# USB devices providing multiple states or modes
#
[code]....
View 9 Replies
View Related
Sep 29, 2010
In Fedora 13 with the kernel version of 2.6.34.7-56.fc13.x86_64, the NVidia driver of the version 256.53 was installed from rpmfusion repository. Everything works fine except for one problem: the brightness cannot be controlled from the power management programs in either KDE or Gnome. In Gnome, the scroll bar of brightness disappears, and, in KDE, the scroll bar cannot be dragged.
Since the computer with Fedora 13 and NVidia driver installed is Dell Studio One 19 (All-in-One computer) which has no hardware buttons to control screen display options at all, there is no other way to adjust the brightness of computer screen. The BIOS of the computer doesn't include an option to adjust screen brightness either. Since screen brightness is set at the maximum level when the computer is turned on, it is not possible to continue using the computer for a continuous period of time due to eyesight protection. Strangely enough, both the Nouveau driver included in xorg-x11-drv-nouveau 0.0.16-8.20100423git13c1043 from Xorg 7.4 and the driver included in the mesa-dri-drivers-experimental 7.8.1 support brightness adjustment without any glitches.
View 4 Replies
View Related
Jun 30, 2015
As the subject states i have a desktop with a radeon 9200 card, when i install the firmware-linux-nonfree the system hangs when x starts(sometimes you can see the login manager, sometimes not, but you cant login at all) and i cant access any of the terminals ctrl+alt+f(1-6), after removing the firmware-linux-nonfree package the system boots, but the graphics are under software render...
View 3 Replies
View Related
Aug 11, 2010
making/buying a 3 pin j2 serial connector for my computer to connect to a programable chip
View 1 Replies
View Related
Jun 12, 2011
I'm trying to use MySQL's JDBC connector for java but even though I set the CLASSPATH variable, java cannot find the com.mysql.jdbc.Driver class.
Code:
[jordan@Jordan-Laptop java-stuff]$ ls /usr/share/java
cal10n geronimo-jta.jar java_cup-runtime.jar
[code]...
View 14 Replies
View Related
Sep 11, 2010
I'm running CentOS 5.5 on a Shuttle SG41J1 PLUS barebones system. All is working well, except the sound. I get sound only on the front connector (meant for headsets). With XP on that box I get sound on both the front and the rear connectors. Under XP I see the dialog as attached to this post. It even knows where I have something plugged in. Under CentOS I have two devices listed:0: HDA Intel (Alsa Mixer) 1: IDT ID 76c1 (OSS Mixer) The second one is marked active (*).Any idea on how to make the sound work for the rear connector too ?
View 1 Replies
View Related
Apr 6, 2016
I got assigned to a project, where the installation is done over ansible. As I'm new in linux, python, django, ansible I wanted to try this out on a empty linux debian.
Code: Select alluname -a
Linux DebianABC 3.16.0-4 amd64 #1 SMP Debian 3.16.7-ckt20-1+deb8u4 (2016-02-29) x86 64 Gnu/Linux
When I now run my ansible playbook it tries to install mysql and suddenly I get an error:
Code: Select all:stderr: DEPRECATION: --allow-external has been deprecated and will be removed in the future. Due to changes in the repository protocol, it no longer has any effect.
DEPRECATION: --allow-unverified has been deprecated and will be removed in the future. Due to changes in the repository protocol, it no longer has any effect.
Could not find a version that satisfies the requirement mysql-connector-python==1.0.12 (from -r /home/abc/abcTest/requirements.pip (line 36)) (from versions: )
No matching distribution found for mysql-connector-python==1.0.12 (from -r /home/abc/abcTest/requirements.pip (line 36))
FATAL: all hosts have already failed -- aborting
So I checked the target machine and tried to run
pip install -vvv -r requirement.txt mysql-connector-python
As version 1.0.12 is an old version, I was searching and tried the following: [URL] ....
But also if I run the installation by direct download I have the same error message:
Code: Select allabc@DebianABC:/home/abc/abcTest$ pip install -r requirements.pip -vvv mysql-connector-python
Collecting http://cdn.mysql.com//Downloads/Connector-Python/mysql-connector-python-1.0.12.tar.gz (from -r requirements.pip (line 36))
Starting new HTTP connection (1): cdn.mysql.com
"GET //Downloads/Connector-Python/mysql-connector-python-1.0.12.tar.gz HTTP/1.1" 200 230923
[Code] ....
I was reading about the version requirements from PEP: [URL] .... but as the version looks ok, this should not be the problem.
View 0 Replies
View Related
Feb 2, 2009
How can I find out programmatically if a cable has been removed from an ethernet connector where the interface is "up" ??? Without using ping of course.
Sidebar question, if I have two interfaces on the subnet how can I force a ping out a specific interface? Say, I have 192.168.5.14 and 192.168.5.13 and I want to throw a ping out *.13 and not *.14 ..
View 2 Replies
View Related
May 17, 2010
I am trying to read a 5 1/4 in. floppy disk using an Intel D865 PERL motherboard, at 3 GHz. Bios was set to read this floppy. The system Lenny 2.6.31 i386 can't detect the 5.25 drive. Drive select seems not to be responding on the 5.25 drive. When connecting a 3 1/2 in. drive to the same motherboard connector (after changing the BIOS setting appropriately), r/w is ok under both linux and XP. I have tried three floppy 5.25 drives and different cables. All known to be ok on another box. I have tried XP and another linux, Etch. I have installed the latest available Bios upgrade from Intel. Upgraded from 0061 to 0089 bios versions. Is this a possible connector difference between 3.5 and 5.25 drives on the drive select line? The cable drive end connectors are different between the two drives.
View 5 Replies
View Related
Jan 18, 2010
I want to ask how i set Linux class path for mail.jar and mysql-connector.jar. I have set the class path for java with the command.
Code:
when i do java -version it's work fine.
Also if i want to know that what shell i am using how can i find it.Also what is the command for showing class path variables or how can i see my JAVA_HOME class path.Means after setting the class path for above two files how can i see that these files have added.
When i write echo $CLASSPATH or echo $JAVA_HOME it shows nothing no error but again shows the prompt.
One thing more i want to run a java program on Linux it is in a package (named asteriskproject). It consist of 10 java files. I have run this program on windows using netbeans IDE.For this program i need to set my Linux class path for the above mentioned files, and this is my first time that i am running any program on Linux. So i want to ask how can i run my program. Simply put this asteriskproject directory in any folder and run the main file using javac. Is it right way to run the program that consist of package ?
View 3 Replies
View Related
Jan 15, 2010
My hdmi out is not showing on tv, what should I do ?
sony vaio VGN-FW51MF
ATI mobility radeon HD 4650
View 2 Replies
View Related
Jun 22, 2010
I just noticed that rhythmbox isn't showing the nice libnotify popups on song change. I use the next/prev buttons on my multimedia keyboard, but I can't see what I'm listening to anymore.I can't find the option to enable or disable this feature.how I can resolve this?
View 3 Replies
View Related
Jul 25, 2010
There's several threads dealing with overscan, but I've got an interesting twist in my setup that (I believe) is putting a kink into the proposed solutions. I'm trying to set up a media center PC with Ubuntu 10.~. The motherboard has built-in ATI graphics (3300 series), and connects to my television (Panasonic capable of 1080i) via HDMI. As can be expected, the overscan makes the top and bottom bars nearly invisible (as well as a portion of the sides).
When I run the Catalyst Control Center, it informs me that the monitor is a projector, not a TV. Try as I might, I can't convince the thing it's attached to a TV. When I run "aticonfig --tv-info", I am informed that a TV is not connected.
One question I could ask, though: does it matter? The reason I'm asking is that I can't find the "Configuration" menu option in the CCC that all the other threads talk about. I know where the little black triangle menu is, but there's no "Configuration" item in it. There's also (as best as I can tell) no way of adjusting overscan for a digital projector.
View 4 Replies
View Related
Dec 24, 2010
Ubuntu 10.10
External slimline HP cd/dvd combo drive
No other optical drives on system
I am having a problem ripping or playing audio CDs on my drive. DVD movies work fine on this drive, but audio cds will not show up in Rhythumbox nor SoundJuicer. Oddly, they will play in VLC.
I wish to rip music to my hard drive. When launching Sound Juicer, I receive the error "no CD-Rom drives found".
View 1 Replies
View Related
May 10, 2011
I've got a headset with a microphone plugged in, but not recognized by KDE's mixer.
Code:
Bus 001 Device 006: ID 046d:0a0c Logitech, Inc. Clear Chat Comfort USB Headset The device is visible in system settings: System Settings->Multimedia->Phonon->Audio Capture
but not in the mixer under Capture Devices. Is there an easy way to get either the notebook's built-in mic or the headset mic to start?
View 2 Replies
View Related
Jul 21, 2011
In 11.04 there seems to be several posts regarding dual monitors. When I tested 11.04 prior to making it my os Monitor Preferences detected both of my monitors, as did Nvidia Xserver.
So installed 11.04: After enabling my 2nd monitor using Twinview when I reloaded I get the following in the top right hand corner. (This ss was taken during some testing when I removed my 2nd monitor it shows 3600x1080 when both are plugged in) The Unity desktop or Classic will both load up and I can use the screens just fine. The problem is whenever I put games, or even a ..... video in full screen it breaks is the only way I can put it. I open up Monitor Preferences and it show Uknown Monitor with a resolution of 3600x1080. I can only assume that its trying to make the games etc use that resolution. Tested wow in wine and it shows that res even after I forced it to use my primary at 1920x1080.
I am new to Ubuntu so not sure if Twinview is working as intended but I am guessing not. As I have seen many other with Dual Monitor issues and not sure if this is the same thing. I have no problem using max for windows but anything Full Screen is where the issue is. I have tried setting the positions to "Left of" instead of absolute for the 2nd monitor but it changes back each reboot.
[Code]...
View 2 Replies
View Related
Dec 12, 2008
I would like to know when usb inserted, its showing cant mount when i clicked details its showing bad blocks in beginning , and smething in /dev/sd6. Can i knw why usb drive cant be mounted automatically , even if its set to do so, and to cope the error mentioned above
View 1 Replies
View Related
