Ubuntu :: Built On A ASUS P4S800D-E Motherboard And It Has An ATI Radeon 9200 LE Graphics Card
May 23, 2010
I just lost my weekend trying to install Xubuntu 10.04 on my pc I made the ps a while back - its built on a ASUS P4S800D-E motherboard and it has an ATI Radeon 9200 LE graphics card. It has a PS/2 keyboard and mouse, 1Gb of memory and a 160Gb PATA/IDE hard drive (I unplugged the SATA drives) Every time I installed or made a tweak to the config it failed in the same way. It showed its failure by continually repeating the first character typed. Regardless of whether this was the password screen for synaptic or just the first character typed into a terminal. Until the first character was typed the mouse seemed to work ok but then it would stall too
I've tried most things, running Xorg with/without an xorg.conf file, loading the ppa kernel and tweaking loads of bios and grub boot parameters all to no avail. So I think I want a more linux friendly graphics card and I fear I may need a new motherboard. Can someone recommend a replacement graphics card for this motherboard? Can anyone reassure me that my motherboard is ok with linux?
View 1 Replies
ADVERTISEMENT
May 28, 2010
I've been meaning to get back into linux for a couple of years now.It seems I may have left it too long for my hardware.I'm struggling to freshly install lucid 10.04 onto a pc with an ATI 9200 graphics card.Can someone give a definitive answer on this - the internet is full of different solutions and I cannot get any to work.
View 9 Replies
View Related
May 2, 2010
I have a Gigabyte GA-MA74GM-S2 motherboard with integrated graphics that shows up on lspci as an ATI Radeon 2100. I also bought a PCI-Express Nvidia graphics card so I could use the VDPAU feature on Linux (plays H.264 in hardware). The BIOS has three settings about which display to initialize first:
Integrated graphics
PCI graphics
PCI-Express graphics (PEG)
I set the BIOS on PEG, but
I cannot get anything, not even a splash screen or POST messages, to emerge from the PCI-Express graphics card. (I'm using a DVI connector; the card also has an HDMI output.)I cannot get the kernel lspci to see the graphics card; the only VGA controller it acknowledges is the integrated one.Running dmidecode acknowledges the existence of an x16 PCI Express slot, and it says
Current usage: Unknown
There is an additional BIOS setting called "Internal Graphics Mode" which is normally set to "Auto" which means it is supposed to prefer a PCI Express VGA card. I set it to "Disabled" which now means I'm getting no output at all. I will soon be learning how to do a BIOS reset!
Other information: The PCI-E card is a MSI N210-MD512H GeForce 210. This is a fanless card. Although there are no fans to see turning, the heat sink on the PCI-E card is definitely getting hot, so the card is getting some sort of power.It gets all its power from the PCI-E slot; there is no external power connector.The BIOS is an AMI Award BIOS.how can I make the PCI Express graphics card visible to Ubuntu?
View 1 Replies
View Related
Sep 5, 2011
I just bought a new graphics card and installed it. it works perfectly although my sound worked perfectly this morning and I think the graphics card is overriding my built in sound card. I need help fixing the sound. The graphics card I bought is an ATI Radeon Cedar HD 5450 The sound I want to use is HDA VIA VT82xx
when I run alsamixer I get Card:
HD-Audio Generic
Chip: ATI R6xx HDMI
[Code]....
View 3 Replies
View Related
Jul 7, 2011
I have a dvd player motherboard which includes an ide port and audio video outputs.
I wanted to if there is a hack to connect the ide port ( or sata with convertor) to a hardware containing an embedded linux OS so as to use the dvd player motherboard as a graphics card.
View 2 Replies
View Related
Aug 23, 2014
My computer boots up, grub loads up, but I enter tty1 instead of the desktop environment.
I am using Debain GNU/Linux 7.0 (wheezy).
My mother board is an ASUS M4A88T-M.
Former graphics card was a Radeon, bought within the past couple years, pretty high specs. (I am having trouble determining what the card is right now, I'll update my post when I figure it out).
I remember having to mess around with some config files to get it to work at first, but right now how to 'unfix' it now.
View 1 Replies
View Related
Nov 5, 2010
Did anyone try to get ATI Radeon 9200 working on Maverick? For me, the DVI flickers all the time like crazy and is totally unusable.
frglx doesn't seem to support it anymore, adding Option "NoAccel" partially solved the issue
View 2 Replies
View Related
Apr 29, 2011
After I've installed an ASUS graphics card (ATI chip) my Ubuntu got no sound at all. My Codec is: VIA VT1708B 8-Ch. I've chosen "Internal Audio Analog Stereo" in Sound Preferences. Windows on the same machine works properly.
View 3 Replies
View Related
Apr 14, 2010
I had a problem with OpenGL on my computer (I run Ubuntu), and so I created a thread here: [url] but it turned out that the problem was with my graphics card, so I made a new thread at the Ubuntu forum at [ubuntu] Problem with OpenGL in Ubuntu - Ubuntu
View 4 Replies
View Related
Jul 15, 2009
Fully updated F11, video card sapphire radeon atlantis 9200. Xorg keeps crashing randomly and kicks me out to the F11 login screen, sometimes when I try to close a window, other times just by itself.From /var/log/messages at the exact time of the crash:
kernel: Xorg[1663]: segfault at 70c0b30 ip 049de1de sp bfaf0bac error 4 in libgcc_s-4.4.0-20090506.so.1[49bd000+2a000]
gnome-session[1831]: WARNING: Detected that screensaver has left the bus
[code]....
View 2 Replies
View Related
Jun 3, 2010
find the manuel download for my radeon 7500 graphics card. I'm having a hard time finding it. Also, please look, at this other thread, I'm having a big problem: [URL]...
View 1 Replies
View Related
Mar 30, 2011
I can't install my graphics card Radeon HD 3200, I use the same driver as I always do. But this time it did not work, it boots with an X error and I can't get into gnome.
Here is the Xorg log.
X.Org X Server 1.7.7
Release Date: 2010-05-04
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.32.29-dsa-ia32 i686 Debian
[Code].....
View 6 Replies
View Related
Mar 11, 2011
I changed my graphics card from Nvidia GeForce 2 MX200 (drivers I used were nouveau) to ATI Radeon 9200SE (now drivers should be radeon). Unfortunately I couldn't get X to start. It leaves me to black screen with white cursor blinking. Both cards are AGP on old Slot 1 motherboard. Reason for change was that GeForce didn't support interlacing on VGA. There are no updates installed to Debian (Squeeze), because there is no internet connection on this computer currently. I tried few things but they didn't work:
* I tried to reconfigure xserver-xorg, didn't help
* I tried to make xorg.conf with X -configure and then moved it to correct place, didn't help
* I tried radeon.modeset=0 option, but it didn't help, I had some other problems with this but I think it's not important (I'll tell later if needed)
I tested Fedora 15 Alpha XFCE LiveCD, but it didn't boot because of my CPU I guess (VIA C3 1 GHz, Nehalem core). I also tested Ubuntu 10.04 LiveCD, but it told that there was an error with radeon and low graphics mode is needed or something like that. So it was as bad as Debian. I took few logs and stuff to pastebin.
Xorg.0.log
dmesg
lspci
View 4 Replies
View Related
Jan 20, 2010
I have an ATI Radeon 9000 Graphics card that Ubuntu 9.10 doesn't seem to recognize no matter what I do. Knowing that its an older card and that ATI stopped support for it a while ago, I was wondering if anyone knows if I would have better luck on Ubuntu 8.04. I can't get 3d or opengl to work, or install the correct ATI Driver.
View 2 Replies
View Related
Nov 8, 2010
I'm having problems with my graphics. I have ATI mobility radeon hd 3650 and I get an issue with desktop effects. They can't be enabled even though the card is supported. I had some trouble with installation and used this thread's instructions: http://ubuntuforums.org/showthread.php?p=9133906. I finally seem to have it installed and configured but I still can't use desktop effects. Also this whole process started because I couldn't get minecraft working getting the GLX13 error.
View 1 Replies
View Related
Aug 3, 2010
A friend of mine is looking for a cheap PCI graphics card to do TV-out from his PCI only PC for MythTV duties. We've found cheap old PCI Radeon 9200's with TV Out on eBay. These appear to only be supported by the open source drivers now, but will the TV out work with the open source drivers?
View 3 Replies
View Related
Mar 1, 2011
I am thinking about buying a new computer. It has ATI Radeon HD 3000 Graphics. Does Fedora 14 support ATI Radeon HD 3000 Graphicst? Will I have to install a driver and if so where would I download the driver?
View 4 Replies
View Related
Mar 13, 2010
I recently bought a HIS HD 4670 IceQ card but can't get it to work in openSUSE 11.2 Under Windows the card works fine, so I assume there is no hardware problem. I tried this card in two computers with different mainboards, but it does not work. Several times I reinstalled openSUSE completely from scratch (tried both 32bit and 64bit versions) but no luck. The problem: Right after the installation it uses the radeonhd driver. This basically works, but without 3D (no Tuxracer...) and even 2D is slow (dragging around windows on the desktop is slow, page scrolling in firefox also).
Then I tried to install the ati proprietary driver, both from rpm (the rpm's from the "official" ati repository have a checksum error, as already mentioned in another thread!), and by downloading the driver from AMD and running the install script. The install script seems to work successfully. The kernel module is compiled and loaded. "aticonfig --initial" makes a rudimentary xorg.conf. But then, when starting X, it does not work:
- on one of the 2 tested systems, even kdm does not start, the screen simply stays black with a frozen cursor top left, even CTRL+ALT+backspace doesn't do anything - on the other system, kdm starts and shows the login screen, but when trying to start KDE kwin crashes, and the windows have no title bar (when I googled for this symptome I found lots of people also having this problem...) - trying to configure the system using sax2 didn't help, even sax2 doesn't display properly I have now spent 4 days trying to get this to work and now I'm really tired of those buggy graphics drivers, be it proprietary or open source...
Can anyone recommend me a graphics card that is approximately as powerful as the radeon 4670 (I bought this card because it is said to be the most economical card (both in price and energy consumption) that allows to play Anno 1404 reasonably well on windows), but is known to work in openSUSE 11.2, even in 3D mode (tuxracer...)?
View 4 Replies
View Related
May 4, 2015
I have an older computer and I did a fresh install of Jessie
Procesor AMD, Graphic card ATI Radeon 9200 PRO / RV280
After instalation my computer boot into black screen. I have no problems with wheezy.
I installed manually firmware-linux-nonfree (in case) module R200_cp is loading correctly.
When I configure Xorg, my log file says something like that:
-----------------------------------------------------------------------------------
(EE) Segmentation fault at address 0x0
Fatal server error:
(EE) Caught signal 11 (Segmentation fault). Server aborting
--------------------------------------------------------------------------
View 14 Replies
View Related
Jun 30, 2015
As the subject states i have a desktop with a radeon 9200 card, when i install the firmware-linux-nonfree the system hangs when x starts(sometimes you can see the login manager, sometimes not, but you cant login at all) and i cant access any of the terminals ctrl+alt+f(1-6), after removing the firmware-linux-nonfree package the system boots, but the graphics are under software render...
View 3 Replies
View Related
Jul 11, 2014
I've set up this new PC, the graphic card I picked is the ATI R7 260X, pretty good card with lots of core processors, high clock and 2GB memory. I'm now currently using the 14.4 catalyst drive, it works actually alright, though, there are some mishaps with this driver:
First my hdmi screen had scale down, leaving black borders around, even though the catalyst control said the correct native resolution, this turned out to be a underscan that fglrx does and I've finally managed to fix it. Other caveat is that the screen simply won't suspend or turn off( via software), DPMS actually works, forcing it turns the screen blank for some seconds but something does not allow the screen to sleep.
Performance wise it seems pretty good though, everything is pretty smooth, being able to play games maxed out on resolution and ultra settings, though, I still haven't tested out that many games.
The open-source radeon on the other hand, well its open-source, fully xorg and linux compatible, which is a major plus point. It seem it has come a long way, supporting lot of features and providing better performance in some cases.
Before installing Catalyst I had issues with mesa and steam, steam would complain about not finding the 32bit libraries, this is however a steam runtime issue, maybe it could already be fixed.
View 1 Replies
View Related
Feb 7, 2010
I am trying to use an ATI Radeon x300 graphics card with my current system setup with fedora 12 but i am having an openGL issue. I am trying to create a 3D model using comsol and i get an error like:
Failed to initialize 3D graphics. OpenGL not fully supported.
This is a hardware/software issue with the graphics card... not the program COMSOL. How could i enable openGL support to correct this issue?
View 2 Replies
View Related
Jun 13, 2011
Having just Installed Ubuntu 11.4, I require LAN drivers for ASUS A8N5X Motherboard. Where can I get the drivers? And instructions on how to install them.
View 7 Replies
View Related
Jul 4, 2010
I have ubuntu netbook remix on my netbook and how Do I wondering how to get the built mic working. I am wondering how to get the built mic workin. My camera works perfectly but not the mic. When I make vids on ....., there is no sound!
View 1 Replies
View Related
Jul 24, 2009
I need to put a pc together for home use to act as my server. I need recommendations for a asus motherboard. I need it to support 5.3 and looking at asus website I cannot for the life of me figure out what I need. I also want to use a amd cpu. It has been years since I built my own pc and never for linux
View 3 Replies
View Related
Feb 24, 2010
I cannot get sound from a machine that has the M4A785-M motherboard, and a Radeon HD 4670..
My details are at: [URL]
View 7 Replies
View Related
Apr 6, 2011
I just assembled a new computer with Intel Core I3 processor and Asus P8H67 motherboard and 4 MB of memory. It has a 2TB Hitachi Deskstar Hard Drive and Asus DVD. I am trying to load Ubuntu 10.10 directly (without first loading Windows) without success.
I have tried 4 separate downloads of Ubuntu - 64 bit, 32 bit with Desktop and Alternative. I have changed a variety of parameters and various tricks suggested on other threads. The Desktop (32 and 64) versions get me to Busybox shell with message (Initramfs) Unable to find a medium using live file system. The Alternative version hangs with the messages:
RAMDISK: Couldn't find valid RAM image startgin at 0;
No filesystem could mount root, tried ext3, ext2, ext4, fuseblk;
Kernal panic - not syncing VHS;
Unable to mount root fs on unkown block(1,0).
For parameters I think have tried them all (but not in all combinations). I tried exiting twice from BusyBox as suggested on forums but that just hangs the system. I also turn off the quiet and splash to try and see what is going on....but it is too complex and goes to fast for me to follow.
A final suggestion was that the P8H67 is too new for Ubuntu 10.10 and to try the new version 11 coming out...I am new to Linux and reluctant to try a Beta
View 3 Replies
View Related
Jun 14, 2010
I don't get any sound with any version of Lenny on my new ASUS M4A785TD-V EVO motherboard. However the sound works fine when I boot from the Debian Live 60 Alpha1 AMD64 KDE DVD. I can always wait until Squeeze is released and then do an upgrade but I'd like to get the sound working now. Any suggestions?
View 3 Replies
View Related
Jun 25, 2010
no sound with motherboard Asus M4A78T-E for fedora 13
View 7 Replies
View Related
Feb 10, 2010
I also posted this as a question in launchpad, but wasn't sure if this might be a better place. Pretty new to Ubuntu, if you couldn't tell.I just upgraded from 9.04 to 9.10 and cheese/skype don't see the webcam built into my machine. It worked with Windows 7 that came with the computer, and in 9.04. I'm using a Asus 1005PE.
result from lsusb:
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[code]....
View 2 Replies
View Related
