Ubuntu :: Installing Sata Card On 10.04?
May 2, 2010
I purchased a new Sata Card today so I can install multiple harddrives on my system, but It appears as though I am missing the drivers for the card, because it is simply not recognizing it. how to obtain drivers for these cards and install them?
Edit - Just in case you were wondering, the Sata Card is Generic, and I have no idea who the manufacturer is. It literally says 'Sata Card' on the box and has no company information, but I did buy it at a reputable business, so I have no doubt that it should work fine. It is most likely this card: Newegg.com - SYBA SD-SATA-4P PCI SATA Controller Card
View 9 Replies
ADVERTISEMENT
Jun 13, 2010
I have an old computer that I want to turn in to a backup server. I was planning on using a 1 TB drive connected by a SATA card since the motherboard only has PATA. However when looking everything I've found makes it sound like I need to install the card for it to work. I want to know if I can install Debian to the hard drive through the SATA card or not?
View 6 Replies
View Related
Aug 13, 2010
Can SATA 3 (SATA III) Hard disk be run on motherboard which only supports SATA II, except sacrificing the speed (throughput)?
View 2 Replies
View Related
May 1, 2011
I keep getting this error in my log viewer every 2 seconds: Code: ata4: limiting SATA link speed to 1.5 Gbps I have a dual boot SSD and I have run many SMART tests in windows and linux, (using smartmon tools and the disk utility) and the reports are all 100% healthy..... My research shows that this error represents one of the following:
1. Problem with SATA controller
2. Changing BIOS to allow SATA
3. Changing SATA mode to PATA or AHCI
4. Replacing the SATA cable
5. Allowing the SSD to run at SATA II speeds, i.e. 3 Gbps
- Does anyone know how to try number 5, i.e. allowing the SSD to run at SATA II speeds? I am lost here and this problem has caused my machine to crash twice when watching a movie in linux/ ubuntu. (It is worth noting that the crashes have only occurred in linux and I have never had an issue in windows, so it does seem to be a linux setting somewhere, hence why I think it is a "allowing SATA II to run at correct speeds issue")
View 4 Replies
View Related
Sep 17, 2010
I have a mac G4 Gigabit Ethernet, with 400MHz processor. I was running the Hardy version of Ubuntu Server last year, although I was booting from the onboard ATA controller. I just added a 2-port Sonnet SATA card and a single 250G SATA drive, and removed all the ATA gear. I installed 10.04 Server, and via guided partitioning wiped the 250G SATA drive, and installed yaboot. When I try to boot from the 250G SATA it hangs up at the "Mac Smiley <-> ?" Icon after the second stage bootstrap prompt, and then cycles.
I looked at some other threads, in fact read this about 4 times and got some good hints: [URL]. I can boot with a live 10.04 desktop CD, and mount the linux partition and look at yaboot.conf:
Code:
fdisk -l
/dev/sda
# type name length base ( size ) system
/dev/sda1 Apple_partition_map Apple 63 @ 1 ( 31.5k) Partition map
/dev/sda2 Apple_Bootstrap untitled 2048 @ 2048 ( 1.0M) NewWorld
bootblock .....
Then I did:
Code:
sudo mkdir /mnt/linux
mount /dev/sda3 /mnt/linux .....
I also tried to get some details on my PCI SATA card via "lspci". How to get this to boot? I haven't quite given up on this older G4 box. It will make a great SSH server and home automation box if I can just smoove out this wrinkle.
View 5 Replies
View Related
Jun 27, 2011
I'm looking for recommendations for a controller card with support for around 8 devices using SFF-8087 cables. I currently have a AOC-SASLP-MV8 [URL] which while working "OK" still has known problems with drivers. Can anyone recommend a card they use for a storage box? I'm using software raid.
View 3 Replies
View Related
May 23, 2011
I'm trying to install Natty from a USB thumb drive on a SATA SSD. My main system is OS X. The method to create an instal USB disk on the download page didn't yield a bootable disk (the partition was readble, with the right files, but GRUB never started). The quick method from the clemsonlinux wiki gave me a minimal bootable drive, though.From there, I tried to install Natty on my SSD.
Once again, the partitioning process appears to work fine, the files are copied, no problem, but the GRUB install fails silently.I think that the problem comes from the fact that, when I boot from the USB drive (even if the SSD is set as the first boot device), the SSD ends up at /dev/sdb, whereas it would be at /dev/sda if the machine could be booted from the SSD.I chose the automatic partitioning method and ends up with sda1 (/), sda2 (ext) and sda5 (swap).If I launch the installer in recovery mode and ask to mount /dev/sdb1 as root, mount reports that sda1 is / (sda1 doesn't even exist), but blkid reports the SSD as /dev/sdb.
The output of the boot_inf_script is clearly pathological, but I didn't manage to get it out of the machine with what I have (gmail is broken in lynx).I've also tried to install LILO instead of GRUB. LILO boots, but doesn't find /dev/sdb (which is now /dev/sda) and gives me a busybox prompt.I've tried to install GRUB from there, but, once again, I get a black screen at boot time.
View 1 Replies
View Related
Feb 21, 2010
I have been trying to install Ubuntu on my main computer for some time. I think I have two problems: my hard drive and video card. I started with Ubuntu 9.04 but got nowhere. I am now trying Ubuntu 9.10 32 bit. I can at least use the live cd if I put the video on safe mode. Just in case you are wondering, I have tried other distros: Fedora, OpenSUSE, Slitaz, Wolvix, etc. Only Slitaz and Ubuntu 9.10 works on a live cd.
Information on my computer:
OS: Trying to install Ubuntu 9.10 32bit
Motherboard: ASUS M3A78
CPU: AMD Phenom 9500 Quad Core
Video Card: Galaxy Geforce 9500 GT 1GB 128 bit DDR2 (Nvidia) Hard Drive: Hitachi 1 TB Sata Drive 3 Gb/sec 7200 RPM Ram: 4 GB (I think, its been awhile since I built this thing) DVD Burner: LG I think I have two problems: the Sata Hard Drive and the Video Card. When I go to install it, I can get to the install menu but from there all I get is a blank screen. I have tried to put the video in safe mode then install it but I get the same result: a blank screen.
How do I know if Ubuntu recognize the Hard Drive and Video Card? I tried the mount command to see what it sees but I didn't notice any Sata Drives. I was told that I may have to do something with the kernel so it will recognize my Hard Drive. How would I do that?
I have been working on this for awhile now. On a side note, does it matter which Sata Plug the hard drive is on? Right now I have it on the 1st one but I would like to move it to the second one because I want a dual boot system. And yes I know I can use the same hard drive but I would like to keep them separated and use a switch to pick which OS system to use.
While running on the Live Cd, Ubuntu seems to know about my video card and ask to install some drivers but then it asked to be rebooted and it came back up not recognizing anything; video card and hard drive that is. On the live cd I ran the following commands: lswh, lspci, mount, and df. I am not too sure if they will show if the hard drive and the video card are working since I did them on the Live CD. Also on the lspci command, I did this after Ubuntu loaded the driver for the card.
[Code]...
View 9 Replies
View Related
Feb 15, 2011
My "Home" server is getting ful, I've got one 1tera-disk and now I wan't to secure all data with raid 5 config. Can someone recommend a good "fairly"-cheap RAID5 SATA card?
View 1 Replies
View Related
Mar 18, 2011
I have a DL380 G3 HP server and I need to attach a 1TB hard drive. Of course the server only accepts SCSI and since I don't have a few thousand pounds to splash about I am looking at alternate methods. What I have done so far is buy a PCI SATA raid card and attach the 1TB drive to it. The BIOS seemed to be playing nice detecting it and allowing me to select the card. But it won�t see the drive.
Funnily enough though when I installed Linux on the SCSI drive during the install it saw the 1TB just fine and I could write to it. This has led me to believe that I could use GRUB (installed on the SCSI) to boot the 1TB as the hardware setup is working but the BIOS just can't handle it. So here I am with no real knowledge of GRUB. I was hoping someone could tell me where to begin with this and if it is even possible
View 3 Replies
View Related
Jun 17, 2011
I'm running ubuntu server (no graphics) 10.04 kernel 2.6.35. I added a PCI SATA card with 4 ports (Masscool XWT-RC040) which according to the company website [URL] supports linux. lspci yields
[Code]....
I would think the third line from the bottom reflects my card. However I can't find any corresponding entries in the /dev folder.
View 5 Replies
View Related
Feb 7, 2010
My computer:
Pentium Dual-Core CPU
E6300 @ 2.80GHz
2GB RAM
XP SP3
2 X 500GB SATA HDD's
Motherboard: ASUS P5Q-EM DO
I would like to install Linux Ubuntu 9.10 on my new computer, on a separate hard drive, and create a dual boot Linux and XP.
I already own another 500GB HDD but this one is IDE. I would like to install Ubuntu on this one. The other two are SATA. The second one is used only to mirror the first one and protect me from a single drive failure.
I hooked up my IDE drive to IDE controller and connected the power cable. However, BIOS doesn't show recognize this drive; it is not visible in Windows explorer, or in disk management either. The jumper is on cable select (so I thought motherboard will decided on boot order, and as the first drive is SATA, it will boot first which is fine).
I double checked all cable connections and tried again, and there was no change. The drive (WD Caviar Blue PATA 500GB) is not registered.
View 4 Replies
View Related
Feb 26, 2010
I have a sata card in my RHEL5 server that is not working. It has a 1.5tb hard drive attached to it that I would like to use. It seems that the 2.6.18 kernel did not detect and use it by default. I was able to find some info about the
lspci | grep VIA
03:06.0 RAID bus controller: VIA Technologies, Inc. VT6421 IDE RAID Controller (rev 50)
View 1 Replies
View Related
Dec 22, 2010
I see the device in dmesg. On the macbook pro 6,1 it gets issued IRQ 19 and loads sata_sil24 and ata_piix correctly, however on the 5,1 and 5,2 macbook pro it only loads sata_sil24 and gets IRQ 24. Is there anyway to specify the IRQ assigned to the device via the kernel (is it an IRQ conflict or device not working on IRQ24)? MacBook Pro uses an EFI so not traditional bios where I can set irqs. Am I looking in the right direction as to the cause of my problem? Slackware 13.1 with standard linux kernel 2.6.35.8
View 1 Replies
View Related
Feb 25, 2009
I have a CentOS box set up as a small home server right now. It is running a Apache Server. A SVN server and is going be a file server for all my friends. The problem is that it I need to add more SATA ports. RAID is not a big deal to me so the card can be a simple add in card. I am limited to PCI because the board does not have any pci expres slots. I am also interested in what hard drives that card would work with. I am hoping to keep them to 500 Gigs min. The motherboard has two built in SATA prots but I don't use them have had bad luck with them in the past
System:
AMD Athlon 64 3400+ cpu
MSI K8N Neo Series motherboard
3 IDE Hard Drives
1 CD Drive
CentOS 5
View 2 Replies
View Related
Sep 4, 2010
I have my home pc and previously it was dual boot as windows and linux.I want to reinstall rhel5.5(32 bit) but I am not able to do so and getting following error:
Error partitioning
Could not allocate requested partitions:
partitioning failed: could not allocate
[code]...
View 3 Replies
View Related
Oct 20, 2009
I tried to load Red Hat Linux 4 on my PC, which has 945 MB, Core 2 Duo Processor, 2GB RAM, 250GB SATA HDD. But i couldnt do so as it did not detect the hard drive and was asking for drivers. I changed the SATA settings to Legacy but still it didnt recognise the HDD...I have Windows XP SP3 also installed on it.
View 2 Replies
View Related
Mar 19, 2009
I'm working on a new server and it has an Nvidia SATA array controller with 2 250Gb SATA drives configured in a hardware array. When the first screen comes up I'm entering the option Linux DD for it to prompt me for the drivers but nothing ever happens. The screen says that it's loading a SATA driver for about 15 minutes and then the screen clears and has a plus sign cursor on a black screen. What am I doing wrong? The only driver that came with the HP server are for Redhat 4 and 5 and SUSE, will any of those actually work?
View 7 Replies
View Related
Aug 8, 2010
I'm trying to install Linux Fedora Core 12 in a PC with a P5GC-MX1333 motherboard from Asus and a Sata hard drive, however, when boot to the installation menu, after chosing the language and keyboard, I get a message that there seams to be no hard drive in the PC. The hard drive is detected in the post during startup, and is also detected by a Windows XP Installation CD.
View 4 Replies
View Related
Apr 19, 2009
Am installing Fedora 10 on an old but good server that used to be a windows box. It has 2 sata disk raid level 1 on adaptec 2410SA card. Disks are clean no info even did a low level format and recreated RAID.. twice DVD boots and installs os on raid array and reports success. new volume appears under computer icon but cannot be mounted after reboot attempt reports Reading physical volumes. This may take a while... (it doesn't)
Volume group "VolGroup00" not found
Unable to acces resume device (/dev/VolGroup00/LogVol01)
mount: error mounting /dev/root on /ysroot as ext3: No such file or directory
input: PS/2 Generic Mouse as /devices/platform/i8042/serio1/input/input4
and then a blinking cursor with keyboard echo but its just copying reboot with install DVD does not show previous (unmountable) disk image and repeat of above process increases operator need for alcohol have "disable write cache for drives" as I found that is a post but after fedora install.I do not know what grub is for instance but once linux is booted (on other computers) I can muddle through ok in terminal mode.
View 1 Replies
View Related
Jul 21, 2010
I have an EeePC 4g netbook which only has a 4Gb hard drive and I thought I would like to install Fedora 13 on an 8 Gb SDHC card and use it to boot the netbook.
As neither the netbook nor I have an optical drive, I made a bootable USB memory stick using Unetbootin which boots the netbook and could be used like a live CD to install Fedora.
On booting with the live USB stick, with the blank SD card in place, and clicking on the install icon, the installation starts but then there are 2 problems; the first is that the installer appears to want to install to both the SD card and also the USB stick. There is a tick in the box beside the USB stick which I can't remove.
I decided to ignore that and put a tick in the box beside the SD card but when it got to the point where it creates partitions it said "Could not find enough free space for automatic partitioning. Please use another partitioning method"
Surely 8 GB is more than enough space for partitioning, so where am I going wrong and why does it want to install on the USB stick as well?
View 2 Replies
View Related
Jun 21, 2010
I installed Ubuntu 10.04, and happened to have an Silicom Images PCXpress card plugged in, and it kindly added the sil_sata module.This is fine for this chip set.I think that my earlier installation of Ubuntu 9.04 used Libata, which does support NCQ and also has good legacy support for the Intel Intel ICH7 chipset I have inside my Sony Vaio SZ notebook. Also, libata also support Silicon Image chipsets as far as I can tell from URL...I wish to remove the Silicom Images SATA modules and replace this with libata and then test the performance between the two device drivers.
View 5 Replies
View Related
Jun 1, 2010
My motherboard supports SATA but I do not know which version: SATA-I or SATA-II. I want to buy a SSD so it would be pointless to buy a fast SSD if my motherboard only suports SATA-I
View 7 Replies
View Related
Feb 15, 2009
The installer can't see my raid controller (I assume) as I'm getting the following error:"Error opening /dev/mapper/isw_jbhgjgjj_Vol0: No such device or address"It just sees them as 4 individual drives: sda, sdb, sdc and sdd.Please note that I have set up the RAID 5 in the controller bios interface and the image name is Vol0, which it seems that it tries to load but for some particular reason it can't.I have also tried different bios settings and nothing worked.
View 3 Replies
View Related
Mar 20, 2011
I tried installing Red Hat linux on my Sata hard disk . As soon as the hardware detection phase starts it generates the error "No hardware detected".roblem? (I have also tested RHLE 5, CentOS 5.4, but none of them detect the hard disk and I can not install anyone).I have installed Windows 7 on one of my disks and I have not any problem with it.I also changed storage configuration in Bios as AHCI, IDE,
My Hardware config is as below:
Mainboard: ASUS P6X58D premium,
CPU: core i7 950,
HDD: two 1 TB WD SATA3
Ram: 6 GB (3*2 GB cruciall[/U][/U][/B]
View 4 Replies
View Related
May 28, 2011
ubuntu 8.04 server can not detect seagate sata hard drive 2tb or sata Lg dvdrw x22 sata drive .is it possible to install it without buying a pci ide sata card?is it possible to get a driver for sata driver and sata drive that can be recognise by ubunto 8.04 server ?or to get the files for 1.44 floppy diskdoes the late edition of unbutu recognise sate hdd and sata cdrw drive automaticly during the installation of the unbutu?
View 1 Replies
View Related
Aug 17, 2010
This would be the one thing that has always held me back from using Ubuntu as my main OS on my desktop. Now with Lucid Lynx in the picture I would really like to try again and get some answers this time around.
I have 2 GPUs in my system, a HD4870 and a HD4350. The HD4870 has a Benq 24" and a Dell 17" which are working fine in a multi-display desktop setting (No Xinerama) configured via CCC.
On the HD4350 I have a single Samsung 17" which in CCC is listed as '[Unknown Display] Unknown adapter' and cannot be used. How can I get that working properly so I can configure it as an additional screen in this setup?
Also on a side note, I have a small problem with CCC. When I installed catalyst and drivers I configured my screen resolution and multi-display desktop, but every time I reboot my resolution for both screens is set to 1280x1024 and they are cloned. Why don't my settings save?
View 9 Replies
View Related
Apr 5, 2010
i have loaded ubuntu 9.10 few days back. I am having problem in configuring my BSNL EVDO CDMA2000 modem(Micromax MMX 300c). Guided by some of the threads, i have followed the below mentioned steps..
xxxxxxx@xxxxxxx:~$ sudo modprobe usbserial vendor=0x05c6 product=0x2001
[sudo] password for xxxxxxx:
Then connected the modem and gave the comment
xxxxxxx@xxxxxxx:~$ lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 004: ID 05c6:2001 Qualcomm, Inc.
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
then i edited the wvdial.conf(i dont understand the details provided in the threads in configuring .conf file)
xxxxxxx@xxxxxxx:~$ sudo gedit /etc/wvdial.conf
[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
[code]....
View 9 Replies
View Related
May 13, 2010
I'm about to install a 'new' ATI Radeon video card into a Ubuntu 10.04 computer of mine (an ASUS A7VT) that has VIA onboard graphics. My question is, how will Ubuntu deal with this? Will it automatically download the required drivers or would I be better off with a fresh install after I've put the card in?
View 8 Replies
View Related
May 17, 2010
I believe my old pIII Dell's network card running Ubuntu server 8.04 is busted. I need to replace it.
how to go about this. Do I just install the card and does it auto-install drivers or is there something else to do?
View 6 Replies
View Related
