I have a PC with Windows XP installed and want to try out how Ubuntu (or Linux Mint) performs when using the nVidia driver.
Unfortunately, after installing the video driver, the live CD, asks me to reboot, so losing all my changes. Is there a way of using the nVidia driver with a live CD?
I've followed leigh's installation instructions for the nVidia drivers on Fedora 14, and everything seemed to go smoothly, but I don't see any obvious changes after rebooting (should I?).When I go to KDE's KInfocenter (KMenu -> Applications -> System -> Info Center) and check the driver information I see this:
Code:
Vendor Mesa Project
Renderer Software Rasterizer
[code]....
I bought a new NVIDIA GeForce 6600GT video card for this PC recently and now whenever I boot Ubuntu 9.10 Live I can't change the screen resolution from 640 X 480. I get this message to the effect that the driver is restricted and not free software. When I try to download it and use it it says I can only activate it after a reboot, but I guess it means after rebooting an installation of Ubuntu, not the live cd since it never takes.
Ubuntu recommends NVIDIA accelerated graphics driver 185, so I went to NVIDIA's web site and downloaded NVIDIA-Linux-x86-185.18.36-pkg1.run (and NVIDIA-Linux-x86-190.53-pkg1.run since I think it's the newest, at least when I enter GeForce 6 Series and Linux 32-bit in the driver download search it's what comes up). I noticed that at the beginning menu of the Ubuntu 9.10 Live cd, when you press F4, the option to load from a driver disk is there. I was hoping this means I could just put one or both of the above files on a cd, insert it into the other disk drive and select that option.
The disk I obtained from a seller runs fine in live mode (no installation) on my Windows XP. I liked what I saw. However, when trying to run cd live on my Linux PC it won't run. Linux pc currently has Kubundu 9.1 installed. Previous to that I had Mint 8 installed, but again Fedora 12 cd would not run. After getting an initial Fedora startup screen, I next receive a bunch of text, ending with a text screen of about 30 lines with "OK" in green to right of each line. At bottom is blinking cursor. That ends my machine's live running of cd.
Obviously, if I can not get cd to run live on linux pc, I'm not going to be able to install. (I should add that ubuntu, kubuntu, mint 8 and pclinuxos all ran successfully live on machine and three of them were installed successfully.) Perhaps, Fedora is at war with Ubuntu et al.
Want to try Ubuntu and am booting from iso CD I burned. Purple screen hangs on red/white dots animation. Then error msg. "The installer has encountered an unrecoverable error. A desktop session will now begin so you can investigate the problem or try installing again" I get a black screen, so I can't do anything in the desktop session. I tried rebooting and hitting keyboard when the boot screen showed a keyboard icon. Nothing happened.
Here is my system info:
Mainboard : Abit AN-M2HD(MCP6
Chipset : nVidia GeForce 7050 PV
Processor : AMD Athlon X2 BE 2400 @ 2300 MHz
Physical Memory : 2048 MB (2 x 1024 DDR2-SDRAM )
Video Card : NVIDIA GeForce 7050 PV / NVIDIA nForce 630a
I just wanted to give Ubuntu a tryout, but if it takes huge amount of fiddling, probably not worth it until I get a new system. I assume it may have something to do with my Nvidia boards.
I have been bashing my head against the keyboard for over 6 hours now i just got a brand new asus ul30v it uses Nvidia geforce G 210M.
I went straight to installing ubuntu 10.10 on the whole disc. when the installation was complete i was happy and logged in. only seconds after i logged in i was promted that i was recomended to install a driver for my graphic card, for 3d and such. so i followed the installation and was asked to reboot. so i did. but then ubuntu booted straight into fullscreen terminal.
While being in this terminal i have tried to purge and reinstall GDM amongst endless other things, including rebooting several times.
Not being able to do anything about it, i reinstalled, and repeated the installation of the driver. same story over again.
Bottom line is i have rebooted close to 30 times, and reinstalled over 5 times. ive tried installing from the terminal (excactly the same story). tried to download it from their homepage, then install it (couldn't install it because i had to turn off driver X and "terminate all OpenGL applications", wich i dont know how to do. tried googling it, but ended up worse than before..[url]
Im guessing i cant install the driver at all with ubuntu 10.10? i havent tried it with older ubuntu versions because, of course, i wanted the newest version.
I have barely been using ubuntu before, although i've had it dualbooted.
I have found alot of posts with people getting stuck in terminal on boot, but none of the solutions that worked for them worked for me, probably because they had different problems than me.
I am trying to install mysql 5.1.44..so i downloaded the binary package, i extracted it and then followed the instructions that were in the manual but i keep getting this error when running this command
Code:
scripts/mysql_install_db --basedir=/home/mosty/mysql
the error is
Code:
Installing MySQL system tables...
100315 20:07:27 [Warning] Can't create test file /var/lib/mysql/mosty.lower-test
100315 20:07:27 [Warning] Can't create test file /var/lib/mysql/mosty.lower-test
[code]....
You can try to start the mysqld daemon with:
shell> /home/mosty/mysql/bin/mysqld --skip-grant &
and use the command line tool /home/mosty/mysql/bin/mysql to connect to the mysql database and look at the grant tables:
shell> /home/mosty/mysql/bin/mysql -u root mysql
mysql> show tables
A few days ago I installed 10.04 Lucid beta-2 and it came up OK. I then chose the recommended Nvidia driver "version current", which caused my system to come up in low graphics mode. I removed the driver and the system came up with no X11. I gave up.Yesterday I installed again, hoping that newer updates would fix the problem. The boot is now OK with no proprietary driver activated and all updates installed as of now (April 14, 05:30 GMT).
The Hardware Drivers dialog shows two choices: Nvidia version 173 and "version current (recommended)". Both of these show the status "this driver is activated but not currently in use". The only option offered is the button "remove".
I just upgraded to 11.04 a couple days ago, and it didn't go smoothly because I ran out of space, so I had to pause it and grow a partition.
When I got done there were several problems. One of them is that my nvidia proprietary driver is no longer being used. I found it in "additional drivers" and activated it, but it says "no proprietary drivers are in use on this system. This driver is activated but not currently in use."
I can run the nvidia control panel just fine, and write an xorg.conf file, but after I reboot the above message stays the same.
My xorg.conf file says to use the nvidia driver. My Xorg.0.log shows the nvidia board coming up what seems to be normally.
The "appearance" control panel doesn't even have the special effects tab anymore.
i installed the new beta 10.04 and it seemed right after the install and update that both nvidia hardware drivers were automatically install together. i deactivated both drivers. one driver showed the nvidia 173 driver and the other one showed "current" nvidia driver.
after a restart i then tried to activate the 173 driver. system required a restart. so i did. system booted to a black screen. i believe its at the desktop but i am unable to see it. i tried to hit esc at the boot screen to enter the grub menu but that didnt work.
Fedora Core 8 did not recognize my Geforce 7150M display adapter (in a HP DV6000 laptop), neither did Fedora Core 10 I tried yesterday although this laptop is now already over one year old (I have used Vista because it works out of the box but it sucks as you might have guessed). That could be something I'd like to complain about but I choose not to, I simply want to know how to install Fedora 10 from a live CD (that is all I have now, no DVDs and not too much cash to buy some..) Live CD boots and I can access command line. If I have understood correctly, Nvidia proprietary driver supports my display adapter but it is not included in live cd so I could use X after installation. Problem is that I don't know how to successfully run the installer from text mode. I tried to execute 'anaconda' but it cannot find packages to install when it comes to that. There seem to be no instructions how to install from a live CD that I could find using Google. For sure someone knows what command to execute to begin installation?
View 2 Replies View RelatedI installed the Nvidia driver. When I click on the "Monitors" package it then asks if I want to use my graphics drivers vendor's tool. I say yes and then it pops up the Nvidia X Server Settings dialog. In that menu it indicates I need to run nvidia-xconfig from root. I did this and then restarted the xserver but to no avail I get the same message every time I try to run "Monitors", that I need to run nvidia-xconfig.
View 9 Replies View RelatedI wish to update my nvidia driver (I was running 195.36.24 and I want to update to 195.36.31). I followed all the instructions on this thread (http://ubuntuforums.org/showthread.php?t=1467074) and everything went well until this part:
Code:
sudo sh blahblah.run
The error I get in the terminal reads: You appear to be running an X server; please exit X before installing. For further details, please see the section INSTALLING THE NVIDIA DRIVER in the README available on the Linux driver download page at [URL]...I have no idea how to exit X as it's not in my system processes.I have updated my nvidia driver in the past but have never encountered this problem. I'm running Ubuntu 10.04 on a Dell XPS M1530 if that matters.
Proprietary driver does not work under ubuntu 11.04.I found this in Xorg log:
Quote:
(EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found)
I would like to know if anyone has installed the latest NVIDIA driver on Ubuntu 10.04 (64-bit) which is 256.35 (x86_64).
I am currently having some problem (unstable) with the previous release 195.36.31 (x86_64) and am now considering updating; but, am still reluctant because of possible problems during the installation process.
I am completely failing to boot the Fedora 13 i686 live CD (MD5 check OK), in every case after the progress bar at the bottom completes I am presented with a garbled screen. My system has:
Motherboard: Asus MX-M2V
Graphics card: Gigabyte nVidia GeForce 7600 GS
2GB RAM, AMD64 dual core, etc.
Some websurfing this might be a graphics option and I have tried adding different commands to the boot option before the "quiet" namely:
nomodeset nolapic / nomodeset noapic / nomodeset noapci / nomodeset acpi=off / nomodeset xforcevesa
None of which worked. Both Asus and nVidia offer linux drivers for download:
[URL]
I've got an eight-year old PC that I'd like to breath some new life into. I was using it for my old scanner (HP, no longer supported by MS or HP), but when my Windows installation finally died I thought it was a perfect time to try Ubuntu. (Xsane running under Ubuntu does support that scanner.) I can get Ubuntu started on it, but when I try to activate/install the recommended Nvidia OEM driver, the system gets sick. Ordinarily I'd not worry about it, but the system only starts into low graphics mode, which leaves some dialogs too large for the display and partially unusable or worse. The PC is a cheap homebrew, using an A7N266-VM ASUS mb. It has some kind of Nvidia chipset on board, but no graphics accelerator.
View 2 Replies View Relatedi have GF 6600..when i have install Karmic i was install driver NVIDIA for my GF6600 then finish n restart. but when my CPU booting to Ubuntu..Its Blank..the Driver its not work(Make my Ubuntu Error). Then i Install New Ubuntu Lucid..then i Install the Driver again(i think its will work)...But when i restart n Booting to Ubuntu...Same Error again, The Driver make Blank Screen??
View 5 Replies View Relatedafter a brand new 10.0.4-installation on my x86, the system proposes me to activate the nvidia-drivers for my gc - trying this, I get the following bug report:SystemError: Failed to lock /var/cache/apt/archives/lockWhat to do now?
View 3 Replies View RelatedI recently downloaded and installed Ubuntu 10.10. I thought it was awesome...still do. OK, the problem is i was prompted to install some proprietary drivers and so i did but thats when the problems started. After reboot i couldn't get the GUI or gdm (not sure what to refer it to) to work. It goes directly to a terminal screen every time so i actually reinstalled Ubuntu and tried installing the drivers all different ways but no luck. i also can get into recovery mode and do low graphics. the driver version im trying to get working is nvidia 260.19.12. my graphics card is a geforce 7 series cant remember the number i have a 32bit processor.
View 9 Replies View RelatedI am trying to install ubuntu 10.10 on my new computer: an Asus U33Jc. It is a 64bit machine. Everything seems Ok until I try to install the nvidia drivers. First, I tried to install it through the graphical interface as it popped up shortly after the install. Then, I tried to install the most up to date driver (290.19.36) found on nvidia's website. In both cases I get the same problem.
When I boot the computer it freezes at startup typically at the stage: "Checking battery state..." but not only (sometines before or after). In any case I never get to a graphical interface. I looked at many forums on the web (here here here and here for instance). But no solution work so far. Apparently there is a conflict with nouveau so I have blacklisted it. It seems the computer does not send the information on the good output, so I tried to twick my xorg.conf in different ways without any result.
I have install Ubuntu 10.10 64bit in my sony vaio vpccw16fs which have Nvidia graphics card (GT 230M). I have install it using nomodeset and after entering the system I installed nvidia from System> Administration> Additional drivers. Driver version was current 260.19.06. After installation I was able to see the boot screen but was unable to see the logon screen. The computer froze with the background color of bootscreen which is purple. And I have to restart it and have to choose failsafe graphic mode. And after logging in in failsafe graphic mode. My NVidia driver says I am not using it. How to use nvidia driver properly. I have tried many Tutorials present on internet but none of them works.
Here is my xorg.conf file.
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 260.19.06 (buildmeister@builder101) Mon Sep 13 04:59:45 PDT 2010
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0"
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection .....
After a failed upgrade from 10.10, I went for a complete reinstall. What I'm seeing is that when I install the nvidia-current driver x / gdm doesn't seem to load. I get a blank screen for a bit, then it drops to the last lines in the terminal from loading up. I can ctr-alt-f1 to get to the first tty.
What I'm seeing in my .xsession-errors file is:
Code:
Xlib: extension "GLX" missing on display ":1".
What I'm seeing in my Xorg.0.log is
Code:
[17.511] (EE) NVIDIA(GPU-1): Failed to initialize the NVIDIA GPU at PCI:4:0:0. Please
[17.511] (EE) NVIDIA(GPU-1): check your system's kernel log for additional error
[17.511] (EE) NVIDIA(GPU-1): messages and refer to Chapter 8: Common Problems in the
[17.511] (EE) NVIDIA(GPU-1): README for additional information.
[17.511] (EE) NVIDIA(GPU-1): Failed to initialize the NVIDIA graphics device!
[17.511]
Backtrace:
[17.511] 0: /usr/bin/X (xorg_backtrace+0x3b) [0x80eab1b]
[17.511] 1: /usr/bin/X (0x8048000+0x5fac8) [0x80a7ac8]
[17.511] 2: (vdso) (__kernel_rt_sigreturn+0x0) [0x44940c]
[17.511] Segmentation fault at address (nil)
[17.511]
Caught signal 11 (Segmentation fault). Server aborting
[17.511]
I'm running on an nvidia 295 gtx. On 10.10 with a completed updated system I saw no issues.
I was running 10.10 with an Nvidia Quadro FX1500 and was able to get the effects (Compiz) working after following the manual driver install (found here) and editing my xorg.conf file. After this upgrade, Xserver (my desktop) wouldn't even launch. It just kept going into a terminal for log in. Not bad - better than not being to do anything at all. I removed all my nvidia drivers
Code:
sudo apt-get remove --purge nvidia-*
and then created a new xorg.conf file (and later moved to /etc/X11) using
Code:
Xorg -configure
That now allows me to log in to my desktop. However - no Unity. I've read that some people have had luck with the Nvidia 173 drivers, but not here. When I downloaded the current nvidia driver for my card (Quadro FX 1500) from nvidia, and went to install it manually using (from the directory where the download is)
Code:
sudo sh NVIDIA-Linux-x86-270.41.06.run
Eventually, it errors out with this: The compiler used to compile the kernel (gcc4.4) does not exactly match the current compiler (gcc4.5). For the record, I can't boot from a thumb drive ("boot error") or CD (both were created and tested on a Windows 7 machine.)
I'm a newbie to Linux and I'm using offline ubuntu 9.04 and now I have problem installing Nvidia driver which I don't have access to internet to download driver. Can you show the way to download Nvidia driver? I downloaded from Nvidia Site but I still need internet access to install it.
View 2 Replies View RelatedLong ago (Back in the Intrepid Ibex days) I ran a manual upgrade of NVIDIA drivers from NVIDIA's website, in an attempt to get Wine running better on my system. Now every time I run upgrade manager, this message (or something similar) pops up twice every time I run upgrade manager:Code:The system has detected an obsolete NVIDIA driver in your system.Please install nvidia-glx-185 at the end of the installation with the following command:sudo apt-get install nvidia-glx-185The removal of other NVIDIA drivers will be dealt with automatically.I actually have nvidia's 190 drivers installed, so the error message is a bit of a misnomer.This message has been persistent with every upgrade, and appeared many times during the Karmic upgrade.
Now I understand when I did this originally every time I get a kernel upgrade and rebooted I'd need to reinstall NVIDIA's drivers. But ever since my Karmic upgrade, things seem to be a bigger hassle than normal.. The system almost locks up after reboot. Compiz now seems crippled and I've disabled it just to get a decent framerate.What I'd really like to do is go back to Karmic's NVIDIA drivers and not have to deal with update problems anymore.However, when I attempt to reinstall Karmic's NVIDIA drivers, I just can't seem to make this error message go away or get the drivers to work. I end up frustrated an hour later, reinstalling NVIDIA's drivers because something is broken and I just can't get jaunty's drivers working at all.
I'm having problems with my Nvidia card. X doesn't work after installation (9.10), only command prompt. I've read the instructions at http://www.psychocats.net/ubuntu/nvidia on how to enable Nvidia drivers, but the instructions are only for GUI, which I don't have.
Anyone knows how to enable Nvidia drivers from command line ?
I've been running Lucid since it dropped. Decided to upgrade my NVIDIA 6600gt graphics card to the newest driver I found at the website. Installation went flawless. But after reboot, I got this:
Ubuntu is running in low-graphics mode
The following error was encountered. You may need to update your configuration to solve this.
(EE) May 05 12:24:17 NVIDIA(0): Failed to initialize the NVIDIA
kernel module. Please see the
(EE) May 05 12:24:17 NVIDiA(0): system's kernel log for
[Code]....
I want to use my video card, but after upgrade i got this message:
You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run `nvidia-xconfig` as root), and restart the X server.
will be apreciaTED, after running from terminal I got this
CODE:
rey@rey-desktop:~$ sudo nvidia-xconfig
[sudo] password for rey:
Using X configuration file: "/etc/X11/xorg.conf".
Backed up file '/etc/X11/xorg.conf' as '/etc/X11/xorg.conf.backup'
New X configuration file written to '/etc/X11/xorg.conf'
Upgraded to 10.04 with proprietary Nvidia driver. No plymouth at boot, but dmesg gives error below. On shutdown get large plymouth display. Tried several hints but none work.
2.985912] 1179648 pages RAM
[ 2.985914] 951810 pages HighMem
[ 2.985915] 149486 pages reserved
[ 2.985916] 642 pages shared
[ 2.985917] 208097 pages non-shared
[Code]...