I have had trouble in nearly every linux distrobution cept for backtrack 3(heavily modified ubuntu which has a lot of wireless drivers on it. i know A LOT of people in the past have had trouble with these cards.
View 9 RepliesI'm very new to Debian (and Linux in general), and am currently taking a Linux course at college... I'm trying to get Debian running on my MacBook Pro (late 2009 model) and it's been complicated but I've got the operating system installed on it... I'm just having a few problems, the biggest right now of which is my wireless card, which doesn't work. So, I found instructions on the Debian Wiki for getting the driver for it, but it's not compiled already and I have little knowledge of manually installing stuff through Linux...
View 2 Replies View RelatedI have a dell mp1210 xps laptop. I just recently installed installed Ubuntu 9.10 and am very green. With difficulty I managed to install the drivers for the wireless card and now have wireless on the laptop. In order to get the wireless working I had to restart my computer, and once it booted up again the wireless works, but there is no trace of eth0-my wired network device (Broadcom BCM4401-B0) which was working fine before I got the wireless adapter working. Lspci still shows the device as it did when it was functioning, but ifconfig only shows my local loopback and wlan0 (my wireless device). I am not sure how eth0 got deleted, I am wondering if maybe I have to set up some sort of switching between the wired and wireless adapters so they are not both active at the same time. Any suggestions would be really nice, I have been digging through the forums, but I am unsure of what went wrong or what to do about it.
View 14 Replies View RelatedOk, so spec's on my setup: Ubuntu 9.10 on a Dell Inspiron 530.. Q6600 w/3GB RAM, 500 GB HD w/radion 2600xt and broadcom wlan NIC. My issue is that the broadcom will not connect to my router. I did some searching, found a link from this site detailing how to get my NIC to work on Intrepid, but that's not what I have. I followed that guide anyway, substituting my driver for his (guide is on sampbar.com) and nothing. It's showing now as not ready. I've installed ndiswrapper and grabbed the drivers for my NIC from my Vista install, but when I use ndiswrapper to do that, I get an error saying it can't tell if the hardware is present, then shows me it is present and it still won't connect.
View 1 Replies View RelatedHere is what I have as far as hardware goes:
Compaq Presario V2000
- PROCESSOR: Intel Pentium M 710 -- 1.4 GHz
- RAM 2 GB
- HD 80 GIG
- Duel booting XP Pro with Ultimate Edition 2.8 (I understand this is built from Ubuntu 10.10)
- lspci -vnn | grep 14e4 yields the following:
Code:
03:00.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
I have followed to the tee this guidance: [URL]
I tried the installing b43 drivers with internet (using ethernet)
I tried installing off the DVD using the no internet option
I even tried installing the STA drivers even though I know the 4318 chipset is not mentioned as a supported chipset.
All of these were loaded/extracted with no errors via terminal following the guidance to the letter. Now here is a problem I have not read that anyone else has run into. (maybe I just missed it). When I go: System > Administration > Additional Drivers the only additional driver that shows up is "Software Modem". I can't for the life of me figure out why the b43 and STA drivers are not showing up to activate. I can install drivers all day long, if I can't activate them, it really does become a moot point.
I've got the b43 driver and firmware installed, and the system comes up fine, but the max throughput on the wlan0 is about 100Kb/s. My laptop and iwl do about 2.5Mbps from the same location in the house. The signal is plenty strong:
wlan0
IEEE 802.11bg ESSID:"sar2"
Mode: Managed Frequency:2.422 GHz Access Point: 00:23:69:22:5C:00
Bit Rate=36 Mb/s Tx-Power=20 dBm
Retry min limit:7 RTS thr:off Fragment thr:off
Power Management:off
Link Quality=61/70 Signal level=-49 dBm Noise level=-57 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Is this expected from the b43 driver and a bcm4318? I was hoping for much better throughput. Also, I tried the broadcom-wl driver, but it doesn't seem to recognize the card. It looks like it's not supported from their site, only the 4311,12,21,22 were listed, although I see posts where other people claim they are using it with a 4318?
I just installed Ubuntu 10.10 on my new Acer Aspire 5551 notebook and for some reason Ubuntu does not want to install the Broadcom STA Wireless driver comes back with an error Sorry installation of this driver falied please look at the log file for details
/var/log/jockey.log
I computer literate but I'm new to the Ubuntu world.....I already know that this OS is far superior to any Windows based OS it is not even comparable.
I just installed Lucid Lynx on my Dell Vostro 1000 laptop. The problem I'm having is that my wired network card has died on me prior to installation. I'm having the hardest time finding the required files to make my Broadcom BCM4311 wireless card work without being able to download any packages from the web. If anyone knows which files I need and which order I should use to install them that would be great.
View 5 Replies View RelatedMy broadcom wireless device is of model BCM4313 and I dont find the way to install the drivers.
View 4 Replies View RelatedJust installed Fedora 14 from the Live CD i686 on my Dell Inspiron 1521. I can't connect to the SpeedTouch 585 on either wireless broadcom card or the wired Ethernet card.
I can connect to it from the same Laptop on the Vista which is on dual boot on the same laptop.
Further confusing is that I ran Fedora 14 and connected to another SpeedTouch today.
Already checked the Channel on the wireless nic and it's on the same one as the SpeedTouch.
when it comes to openSUSE but I am earnestly trying. I installed the openSUSE OS on my HP dv6000 laptop, but it does not seem to recognize my wireless card (which is a Broadcom 4311).
View 7 Replies View Relateddell laptop and went out on thenet looking for a solution for my failed wireless interface. i downloaded the firmware but then my interface still fails to come on after a reboot.
wlan0 IEEE 802.11bg ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=0 dBm
[code]...
Aluminum Unibody macbook, the only aluminum macbook to date. It has a Broadcom chip in it and I installed the STA drivers. The first day it seemed to work fine. Then I noticed pages stopped loading. The max throughput I get is like 30KiB/s once in a while. Sometimes I see consistent speeds of 600B/S...this really sucks. Is there a fix or anything?
I was going to make the switch slowly to 10.10 full-time, but the wireless issue is bothering me. The keyboard brightness keys don't work natively, but there's a fix I saw but didn't have time to implement earlier. I like ubuntu but I don't like my wireless not working!
I have a Broadcom BCM4311 wireless card on my Dell D620 laptop.
Code:
09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5755M Gigabit Ethernet PCI Express (rev 02)
0c:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01)
My wireless works perfectly with my university networks. But I have problem connecting to my house router. The first time I installed Ubuntu 10.10, it connected to internet and worked well. After a restart needed by nVidia driver, my house wireless stopped working while my university wireless still works. I have tried reinstalling the driver using System/Administration/Additional Drivers and manually
Code:
sudo apt-get update
sudo apt-get --reinstall install bcmwl-kernel-source
I'm new to Ubuntu. Today, I took my old Compaq Presario V3010US and gave it life with Ubuntu 10.04. The hard drive was erased and replaced with the Linux OS stuff. Ubuntu recognizes most of the hardware except my Broadcom wireless card. I find this to be a pain because i'm a newbie to linux stuff. Anyway, can anyone help me fix this? I thank you for your time reading this.
View 1 Replies View RelatedI decided to start of with Debian. I'm having trouble getting my wireless connection to work. I think i need drivers or something, i can't make a wireless connection. And it is a bit difficult for me, as i am new to Linux, and I'm not sure what I'm doing when i am writing these commands.
My wireless card is a Broadcom Corporation BCM43142 802.11b/g/n
I have been using Raspberry PI a little, so i am familiar with the terminal.
Ever since I upgraded to the new Ubuntu, I have been having problem with wireless. In the "Hardware Drivers" I come up with 2 drivers:
1) Boadcom B43 wireless driver
2) Broadcon STA wireless driver
I activated the first one, but latter noticed that the wireless was not working, so I tried installing the second and it returned this message:
Quote:
So I unactivated the first and then it disappeared leaving me with the second, and its error message.
Quote:
What should I do now?
The output for "lshw -C network":
Code:
The last few pages of /var/log/jockey.log.
Code:
I seem to be have issues periodically connecting to wireless networks with WPA. It'll work one minute, and then I switch my macbook back on after a period and it refuses to connect again. It's happened on and off on three different networks now.
An example of /var/log/syslog:
Code:
Apr 15 17:57:27 macbookpro NetworkManager: <info> Activation (eth1/wireless): association took too long.
Apr 15 17:57:27 macbookpro NetworkManager: <info> (eth1): device state change: 5 -> 6 (reason 0)
Apr 15 17:57:27 macbookpro NetworkManager: <info> Activation (eth1/wireless): asking for new secrets .....
Apr 15 17:58:27 macbookpro NetworkManager: <info> (eth1): deactivating device (reason: 0).
Apr 15 17:58:27 macbookpro NetworkManager: <info> Policy set 'Auto eth0' (eth0) as default for routing and DNS.
Apr 15 17:58:29 macbookpro wpa_supplicant[949]: WPA: No SSID info found (msg 1 of 4).
Apr 15 17:58:29 macbookpro wpa_supplicant[949]: No network configuration found for the current AP
Apr 15 17:58:29 macbookpro wpa_supplicant[949]: CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
I have recently installed Ubuntu 10.04 beside my Windows XP on my laptop:
Dell XPS 1330
I`m now facing some problems with my new OS :
1. The driver for my wireless network card isn't recognized although I have installed the recommended driver which was in Ubuntu Hardware Driver section.
2. When I connect my laptop to my TV using HDMI port, the screen is OK but there is no sound!
3. When by any reason my network cable is unplugged, the whole network service goes down and I have to restart the system.
lspci results:
I just installed fresh Squeeze to my new hpmini 210-1100 netbook. No wireless. I have checked and I have Network Manager installed already.
I also compiled and installed Broadcom driver from here[url]
I followed their instructions and compiled the driver. I did get a wl.ko driver and installed it insmod wl.ko after modprobe lib80211
I noticed after rebooting neither wl.ko nor lib80211 showed when i did lsmod. So I did modprobe and insmod again. Still no wireless. Here are output of some commands that I thought would be relevant.
lspci:
I see only 2 computer icon in the system tray but not the parallel bars. When I went to System>Administration>Network, I was not able to add my wireless network name. The Add button was grayed out.
I chose to change my operating system from Microsoft Xp to Linux and finally chose Fedora to be my new OS.
After Fedora installation I got a problem that I cannot connect to my wireless network I used to using Xp, I think that my wireless card is not installed on Fedora because when I checked in the network configuration I found that the only installed adapter is the Ethernet Realtek for the wired connection.
My OS is Fedora 11.
The CPU Model name is : Intel (R) Core (TM) 2 Duo CPU T8300 @2.40 GHz, so I think that my architecture is x86_64.
My Network controller is : Broadcom Corporation BCM4312 802.11b/g
I'm thinking of installing Fedora 14 on my hp laptop, and need to know if this will support the Broadcom 4322AG wireless card it came with, will only probably use Fedora if the card is already recognized, or an easy gui install. This is the game changer between using fedora or linux mint for me
View 1 Replies View RelatedI finally gave up trying to configue the Broadcom 4311 card. I went and bought a Netgear WPN111 USB wireless adapter. I've looke for the drivers but I can't seem to find them.
View 3 Replies View RelatedI just installed 9.10 and I can't detect any wireless networks. Is the card compatible with 9.10? Do I need to install any drivers? If the card isn't compatible with 9.10 is it compatible with later versions of Ubuntu? Marking this as somewhat urgent as I need to get internet access for some coursework soon, and also because my parents will kill me if they find out I've done anything unusual with the laptop because it's new and they think anything non -MS is a virus.
View 9 Replies View RelatedI have installed SATA driver recently...Even if i can use wifi but i could'nt find any ath0 interface in ifconfig or iwconfig commands....My wifi is taking place through eth1 interface why it happens.....The reason for asking this in order to use aircrack for wep key it says that the injection process only applicable for Athelon interfaces but mine is eth1...I was just trying aircrack-ng...
View 2 Replies View Relatedi have windows vista with a broadcom 802.11g network adapter.I dont know much about computers but i would like to know how to install it on the ubunto OS so i can use internet ?
View 2 Replies View RelatedHow to use the BRCM driver for this following wireless cards?
BCM4313
BCM43224
BCM43225
Seems the since the 2.6.37 kernels it would be included. And wouldn't be necessary to use Broadcom STA linux driver anymore.
I'm about to install OpenSuse 11.3 gnome on my laptop with ubuntu & vista in a dualboot, and wanted to make sure that the Broadcom 4322AG wireless card would be compatible with my laptop.
View 2 Replies View RelatedI am running openSuse 11.1 64 bit on my hp pavilion dv6458se; and am unable to get my Broadcom wireless card to work.
i tried reading a few forums, but they all start when 'lspci' recognizes the card.
My problem is that 'lspci' does not show any 'Broadcom' card.
I have given below the output of 'lspci' for your reference.
I have a DEll Mini 9 - it has worked fine even though it has a limited memory. But Husband only uses to have a surf. It now wont connect to net. The Broadcom4312 Wireless Card is not working on Obunto. It has a Dell 802.11b/g Wireless LAN Mini card installed and Obunto Edition Version 8.04 Have phoned Dell and after several calls on Hold for over 15 mins each time and getting nowhere fast i am coming to you guys/girls. I am not a very good comp person, but i do get by and i am trying, so be gentle with me. in simplistic terms.
View 2 Replies View Related