Ubuntu Installation :: Boot From Usb - Led Flickers Then Fails
Mar 31, 2011
I am trying to get Ubuntu to boot from a usb, and failing.
I have a two year old Acaer Aspire 5735Z with Windows Vista as the OS. This has USB as a possible boot source, now of course at the top of the list.
I downloaded 10.10 and installed on an empty 8 GB Kingston drive as guided. There is just under 4 GB on the drive. The drive had been used before and all deleted.
So at start up the first thing that happens is the led on the USB drive flickers for less than one second, and then the Windows boots.
How can I know that a boot sector is installed ?
View 9 Replies
ADVERTISEMENT
May 27, 2011
My old computer started randomly rebooting so I went out yesterday and bought a new one. It's a standard Intel 64 architecture with 2gb ram etc.The old computer was running Lenny however I'm happy to upgrade, so I just went to the main Debian download site and downloaded:debian-6.0.1a-ia64.netinst.iso (this didn't work, apparently ia64 is for itanium and my machine is definitely not that), so I downloaded: debian-6.0.1a-amd64-netinst.iso, burnt the CD and ran the install. First time through I had a power failure.
Second time through (a complete fresh start - new partition and everything) it went all the way through to completion and reboot.Clicked 'Continue' to reboot and the machine reset as it would normally and the Grub loader started okay, prompted for the "Debian amd64" standard boot image, selected that and the first 6 lines appeared normal, then the messages wizzed by so fast that only superman could read them. Then they stop - here is some of the content...
[3.816673] Kernel panic - not syncing: Attempted to killl init!
Call trace:
get_empty_filp
panic
[code].....
Running it again I get similar stack stuff but it's a different place: [3.541816], [3.427502] And sometimes if I wait for a minute or two it will continue on further but appear to crash again. Hardware details (everything is onboard - no added cards):
G41M-S3
Intel G41 + ICH7 chipsets
CPU: LGA 775 for Intel Core 2 Extreme
[code]......
Is the amd64 the wrong image? Should I try i386? Is it a blip and I should just rerun the entire install again?
View 14 Replies
View Related
Aug 28, 2010
As the title says, when I select the install option on the liveCD, the Ubuntu logo is shown, and the flickering starts. I've tried the vga=XXX option, but no luck. Any experiences? It doesnt' happen with the 9.10 live CD...
View 3 Replies
View Related
Mar 12, 2015
I have just Upgraded debian wheezy to jessie but after upgrading , the gui seems to flicker areas of gui are not repainting on closing applications ,windows do not render properly.
View 5 Replies
View Related
Jun 24, 2010
I'm trying to install ubuntu on a laptop (Acer Aspire 6530), and duel boot with windows vista. However, when starting up the computer with the CD in the drive, the installer fails to load, showing only a picture at the bottom of the screen showing a square and a circle with a person in it... This persists for as long as I have cared to wait (hours) and pressing keys at first results in nothing, then after sufficient key presses just produces beeps...
Anyone know what's wrong there?
View 5 Replies
View Related
Mar 4, 2010
New kernel Fails to boot. video driver is current and I tried reinstall . The .19 Kernel works fine
View 2 Replies
View Related
May 1, 2010
Installed v9 a couple of weeks back and have been causally mucking about with it since. I managed to get XP and ubuntu running as a dual boot system (which was an achievement ).
Anyway, i've upgraded to 10.04 - and already loving it. However... my XP o/s no longer boots. It use to prior to the upgrade. Now, when the XP o/s is selected from GRUB2, I just get a series of bleeps and a flashing _.
Now, I am a complete novice. I actually have no idea where to even begin trouble shooting GRUB2 (and i'm assuming its a problem with GRUB).
View 6 Replies
View Related
May 5, 2010
I created a Ubuntu live usb，it works fine on my notebook, but boots fail on my desktop pc. I found that /dev/sdb1 is always mounted to /cdrom when booting, but usb key is /dev/sdc on my desktop pc, it causes sequence booting process which depend upon files under /cdrom fails.
View 2 Replies
View Related
May 20, 2010
I have Vista on my Samsung R60 + and have installed Ubuntu. On start up I get the dual boot option, select Ubuntu which then goes to completeing install etc, get some HD activity then nothing.
View 1 Replies
View Related
Jun 10, 2010
Dual boot Windows XP SP3 & Ubuntu 9.10 on a single hdd, w/2 partitions. Booted to Ubuntu and upgraded online. XP boots fine, but Ubuntu, not so much; a msg about /dev not found, followed by a shell login prompt. I suspect a grub problem, but haven't been able to find a definitive answer. Since I can at least boot XP, I do not want to do anything that would screw that up and leave me with no bootable OS. I did the "upgrade" shortly after 10.04 was released. Is there a way to reliably fix this w/o possibly screwing up my ability to boot XP, the only OS I can boot? I have no Ubuntu 10.04 disk, as I used their upgrade online option.
View 1 Replies
View Related
Jul 8, 2010
I'm having a lot of trouble with a PC that has been running Ubuntu for ages, since about 8.04 I think. I've run the distro upgrade a few times and it was running 10.04, but for some reason won't boot anymore. So I'm trying to do a fresh reinstall but I can't get the LiveCD to boot. I'm trying to install 10.04 AMD64 desktop.If I leave the CD to boot, I get to a Busybox screen showing the error "No init found. Try passing init= bootarg." and an (initramfs) prompt. This is all displayed at 1280x1024 res - the native image of the screen I'm using.It's an NVidia chipset - an older one. So I tried hitting a key during boot and putting the nomodeset option on. I get the same error, but at a lower resolution
View 1 Replies
View Related
Jan 16, 2011
I have win 7 installed on my main first hdd and would like to install ubuntu 10.10 on my newly installed second hdd. Problem is that during install when i choose manual partitioning my second hdd is not visible. So it is impossible to choose the disk for installation. Tried to disable first hdd in bios but pc than fails to boot from dvd. Tried the alternate ubuntu cd and second drive even then is invisible. Second hdd is visible in win 7 and fully can be manipulated in 7. Tried to format the drive as fat32, ntfs, linux ext 2 and 3, but same problem. Drives are mounted as 1st hdd is primary master and 2nd hdd is secondary master.
View 3 Replies
View Related
Aug 1, 2011
I just upgraded to ubuntu 11.04 but now all the kernels fail to boot. The resolution of grub changed and the older kernels are put into a 'previous kernels' folder. The most recent kernel halts at the message '* Stopping userspace bootsplash [ OK ]' and the previous kernels fail with the message 'Unlink after no-irq. Controller is probably using the wrong IRQ',
or show the background of the login screen with just a white box.
I think the cause is that I have an ATI graphics card (HD Radeon 3650), because on my 2 other computers ubuntu upgrades fine and they have NVIDEA graphics cards.
As a last resort I tried installing different distro's like Linux Mint but it also gived me the 'unlink after no-irq' message.
View 1 Replies
View Related
Mar 3, 2010
Any ideas as to why ubuntu netbook remix would fail to boot after installing? I've tried twice installing it via usb on a dell netbook. Installation completes just fine but screen just flashes over and over as if in a reboot loop. I was able to run the OS via the USB stick just fine even with persistence but the flippin thing wont boot.
View 1 Replies
View Related
Jul 18, 2010
I've installed Ubuntu Server V9.10 (64-bit) on a brand new server I built with no previous OS installed. The drives are two Hitachi 1 Tbyte hdd's configured as RAID1, an ASUS M4A78T-E motherboard with an AMD Phenom-II cpu with 8 Gbyte of memory. I updated the bios following building the computer. The Ubuntu 9.10 server installation appears to go without error. However, on reboot I get the message:
Grub loading
error: no such disk
grub rescue
I suspect the MBR is missing or Linux is not pointing to the correct drive in the grub.cfg.I've made sure the boot order is correct, but other than that I don't really know the commands or syntax to troubleshoot this problem. The only CD I have is the Ubuntu 9.10 server ISO I downloaded and burned to dvd.
View 1 Replies
View Related
Feb 1, 2010
I've installed Ubuntu Server V9.10 (64-bit) on a brand new server I built with no previous OS installed. The drives are two Hitachi 1 Tbyte hdd's configured as RAID1, an ASUS M4A78T-E motherboard with an AMD Phenom-II cpu with 8 Gbyte of memory. I updated the bios following building the computer.
The Ubuntu 9.10 server installation appears to go without error. However, on reboot I get the message:
Grub loading
error: no such disk
grub rescue
I suspect the MBR is missing or Linux is not pointing to the correct drive in the grub.cfg.
I'm a noob to Linux. I've made sure the boot order is correct, but other than that I don't really know the commands or syntax to troubleshoot this problem.
The only CD I have is the Ubuntu 9.10 server ISO I downloaded and burned to dvd.
View 1 Replies
View Related
May 8, 2010
post another windows 7 / ubuntu studio 10.04 dual boot thread, but I've tried researching this all evening and I am still not getting anywhere...
steps:
-- installed windows 7 on my HP g61
-- defragged using perfectdisk 11
-- used windows 7 volume shrink to get windows partition to 65 GB
-- created an NTFS volume in the new 220 GB partition with windows (Ubuntu studio's partitioner would not recognize the space unless I did this first)
-- ran ubuntu studio 10.04 installer
-- deleted the 220 GB partition and the installer automatically created a new ext4 partition with a swap partition.
[Code]...
View 4 Replies
View Related
Aug 24, 2010
I have installed Ubuntu 10.04 LTS-the Lucid Lynx on top of a Windows XP installation. The Windows partition started before I did this. Now, all I get is a flashing cursor when I tell GRUB to start the Windows XP partition.
I have tried reinstalling Ubuntu with no effect. I have tried repairing Windows using a Windows installation disk.
However, I can reach the files in the Windows partition just fine from Ubuntu.
View 9 Replies
View Related
Sep 13, 2010
Recently freshly reinstalled ubuntu 10.04 on a new / blank hard drive and it now crashes on startup. Quick version: I have a nvidia Quadro NVS 295, it gets to the point just after the bios with the flashing dash, seemingly tries to init xserver / gdm then crashes. Keyboard lights go off but the pc stays on, and just sits there with the monitor in power saving mode. Tried in recovery mode, the blue / grey ascii terminal thing pops up for less then a second then the display crashes in the same way.
Swapping with an ATI card borrowed from elsewhere, the new install will boot quite happily. Anyone know how I can get 10.04 to boot with a nvidia quadro NVS 295? Its a bog standard card and my version of 10.04 I upgraded to on my old hard drive works fine. ts a reasonably new dell XPS 64bit pc.
Longer version:
I run 3 monitors using a PCI-e x16 NVS 295 and a PCI NVS 295. This worked great under 9.10 and 10.04. Boss gave me a solid state HD so trying to install 10.04 on that. However on my first install attempt the live CD failed to load (same problem as above, gets to init'ing the display and crashes with no output). I removed the second PCI card to run with just the 1 PCI-e x16 nvidia card, this time the live CD worked fine and I could install, but I am stuck on the boot problem. Booted into the system using the ATI card and did an update just incase something may have changes / been fixed but the issue persists.
View 2 Replies
View Related
Nov 13, 2010
I have an ASUS G51J notebook with Windows 7 installed. I was following This Guide. I set aside about 100GB for the Unallocated partition. When I started my laptop, I chose to boot from CD (which has an Ubuntu 10.10 ISO on it). I saw a purple background with two icons at the bottom of the screen, and eventually "Ubuntu" appeared in the center with a few dots underneath it. These dots would change color from left to right like a loading bar.
This is where my issue comes up. My friend was using this same CD on his Dell laptop and his desktop which has a XFX motherboard, Q6600 processor, and Invidia 470 graphics card. After this "loading bar" was done, he would be asked if he wanted to boot or install Ubuntu.
This didn't happen for me. What happened instead was that I saw what looked like my Windows desktop after having gone through a meat grinder. There were various icons randomly in pieces all over the place. The only icon that was in one piece (by chance) was my shortcut to Skype.
Has anyone seen this before? Am I doing something wrong? My friend was saying that maybe I should try with a fresh reinstall of Windows and try again. I wasn't even given the choice to just boot from disc. It got to the point where I expected it to give me the options to do so, but instead the Kansas version of my desktop shows up after being hit by an F5
View 9 Replies
View Related
Apr 30, 2011
I downloaded the 64bit net installer. I install just the standard, reboot and the machine hard locks on me. It appears to be locking up on Bluetooth.
View 2 Replies
View Related
Nov 21, 2010
I am a complete noob at this and I need a hand. I was about to throw my computer out of the window when I decided to throw the windows out of the computer so to speak. So, I downloaded Ubuntu 10.10 and tried to install. I had a grub rescue after the installation (file system unknown), which I have seen discussed here. Being the noob that I am I decided to try 10.04 because it said it had full support. With this install I get a similar error during installation: grub cannot be installed in boot sector.
So, basically there is an issue with grub and the boot sector. I checked in my BIOS options to see if there was an option that prevented the writing of a boot sector or something, but I have not been able something like that. So, I am wondering if it is possible that Ubuntu does not really erase/format the selected disks or something, leaving any difficulty there.
Does anybody know? Or better yet: what exactly do I need to do a manual grub install?
View 9 Replies
View Related
Dec 27, 2010
Downloaded Ubuntu 10.04.1 Desktop AMD64, tried to install it to a cleand HDD using the whole HDD, i.e. gave it permission to use the whole HDD. Installation process appeared to run OK but when it came to the restart it just fired up the message
error: out of disk
grub rescue>
I've searched this forum and found numerous references to these error messages but cannot make head nor tail of the diagnostic suggestions. Apart from anything else they suggest strings of command lines which I don't understand and can't enter anyway since they don't correspond to my keyboard layout (if I hit > or ) something completely different appears on the screen). Is there someone here who can provide a step-by-step solution in lay language? Or is there such a thing as a bootable file which can be downloaded and inserted into my CD drive to correct this problem?
View 9 Replies
View Related
Jan 24, 2010
When I ran the distribution upgrade from 9.04 in update manager, my screen went blank on reboot and will not recover. Every time I reboot, screen goes blank. I cannot press CTRL-ALT F1 - F6 to gain access to text shells.
I tested booting from the 9.04 live CD and it works fine. So I downloaded the 9.10 live cd on another computer and booted it on the disabled system. Same exact problem on the live CD that I had upon installation: on boot screen goes black and cannot access text shells.
What can I do next to get out of this short of going back to 9.04, which has problems that I do not want to live with?
View 1 Replies
View Related
May 12, 2010
I run "aptitude update;aptitude full-upgrade" today, then I updated /etc/default/grub changing only the default boot line number, and I dully run update-grub, with no error messages. Now Kubuntu will not boot. The new kernel 2.6.32-22 is in the boot menu. When I turn the computer on, a blinking cursor appears on top line, column 8, and after a few seconds this cursor disappears and the screen is blank - my monitor indicates no video signal.
The failsafe 2.6.32-22 grub line does not boot either. I tried pressing Ctrl-Alt-F1, Ctrl-Alt-F2 etc. up to Ctrl-Alt-F10 to get to a text mode login prompt, but the screen remains blank and my monitor indicates no video signal. The workaround is to boot to kernel 2.6.32-21. The machine is Athlon XP, 2GB RAM, ATI Radeon 9600
View 1 Replies
View Related
Dec 4, 2010
I have a 1.0 ghz G4 eMac running Tiger. Using Ubuntu 10.04's Live-CD I installed 10.04 on a 8-gig USB flash drive and it worked very well despite spending nearly five hours to download its files via DSL and a pokey USB 1.1 port. The flash drive's 10.04 installation worked just fine on my eMac and 900mhz G3 iBook except for Airport wireless non-connecting issues.(I like Ubuntu 10.04 because unlike Mint for PPC, you're not hassled or barred from accessing your Mac HD and its files.) THEN, to resolve my wireless issues, I decided to upgrade to 10.10 which took nearly 12 hours, and it seemed to've installed well until I tried booting the flash drive and it doesn't work. I get the Ubuntu icon in the Startup Disk screen but it keeps returning to it even after I select Ubuntu. The error screen I get reads code...
View 5 Replies
View Related
Feb 23, 2011
Why is it that about 98 to 99% of the time my computer will boot to Ubuntu/Lucid just fine but on rare / random occasions after seeing the initial BIOS boot screen and initial cursor just after initial BIOS boot screens, the video will just go BLANK, i.e. does not boot to Ubuntu desktop ?
If I then do ALT,CRL,DEL sequence the SPLASH screen is displayed on the monitor and the system then reboots and then goes thru the complete boot process all the way to the desktop just fine.Why this occasional failure to boot completely to the desktop ?
View 9 Replies
View Related
May 1, 2011
I made a post in http://ubuntuforums.org/showthread.php?p=10753227 but I guess it's closed.I'm having the same issue. I've installed Kubuntu 11.04 32bit twice now. Both times it doesn't do anything when it reboots.No output to the screen.When I boot to the LiveCD and chroot or simply mount the /dev/sda device and run sudo grub-install --root-directory=/mnt /dev/sdaIt says grub installs successfully, but it doesn't fix the problem.
View 1 Replies
View Related
Feb 5, 2009
After editing gdm and reming out line "auth required pam_suceed....................!=root quiet" the server boots but hang with the login screen. other highlighed but all options greyed out.
Boots OK in text mode and operates OK.
After restoring original gdm file problem still persists.
View 2 Replies
View Related
Jun 18, 2009
Anyone succeed with f11 install on netbook (/ on SDHC, /boot on primary SSD/HDD drive)?
My netbook (AAO) works just fine with f11 Live-on-usb-sick (created with live-usb-creator), but fails to boot fedora from SDHC.
View 1 Replies
View Related
