Ubuntu Installation :: Getting Failed I / O Error Message On 10.04 Install
Sep 6, 2010
10.04 new isnstall from cd goes for a minute then I get this error message:
old p3 800 machine, will this distro work on an old machine like this:
BusyBox v1.13.3(Ubuntu 1:1.113.3-1ubuntu11) built-in shell(ash)
Enter "help for a list of built-in commands.
(initramfs) mount: mounting /dev/loop0 on //filesystem.squashfs failed: input/o-put error
Cannot mount /dev/loop0 (/cdrom/casper/filesystem.squashfs) on //filesystem.squashfs
(initramfs)
View 1 Replies
ADVERTISEMENT
Oct 2, 2010
I was trying to install ubuntu 9.10 as a dual boot system with windows and I recieved this error message: The Grub package failed to install into /target/. Without the Grub boot loader, the installed system will not boot
This Error comes up after 94% of the install. I also cannot seem to get the side by side install option to work (sometimes this option appears sometimes it does not) I am not sure but I beleive seome of the install files have been placed on the hard drive because I only get the option now to install on the hard drive and totally wipe clean or the emptiest hard drive. So how would I get the possible Ubuntu install off the Hard drive. I have used this CD to Install before it has no scratches therefore should work. Also If I have Win Xp on a Raid 0 will the Ubuntu 9.10 install ?
View 4 Replies
View Related
Jan 12, 2011
I just having to do a fresh install and get the following message to close after setting up
partitions and on clicking write to disk:
Failed to mount "524M Volume"
Method "Mount" with signature "ssas" on interface
"org.freedesktop.Hal.Device.Volume" doesn't exist.
Only option under message is close button. I'm using Fedora 14 xfce 32bit live CD. The install seems to carry on normally until done but then when I check the partitions I've setup I seem to only have the origonal uneditted default partitions.
View 2 Replies
View Related
Oct 12, 2010
Greetings from Greece. I tried to install opensuse 11.3 in an empty disk . Unfortunately the installation progress stops in 88% and the message error says "error copy live image to the disk". I have burn two different cd but the result is always the same.Is it a hardware problem or the cd is not correct?I had the 11.2 version in the same pc without any problem for a long time.
View 9 Replies
View Related
Feb 20, 2010
I'm a recently proud owner of a new Aspire AS3810T with Fedora 12 installed, when it boots up before entering the boot screen when it loads I see this error message:IOMMU: Mapping reserved region failedHow can i fix this error? It's quite frustrating
View 2 Replies
View Related
Jan 28, 2011
When I send mail via Evoultion it does seem to send ok but still the following error message comes up: Error while sending message. Failed to append to : Unknown error Appending to local 'Sent' folder instead. Not sure what's up with that but thought I would mention it.
View 3 Replies
View Related
Sep 27, 2010
I tried many times to install Ubuntu 10.04 but I keep getting the following error message:
Can't be the CD or the CD drive because I get the same thing with a bootable USB flash drive.
HDD in SATA 1 port
DVD burner on SATA 0 port
HDD formated
Vice versa does not work neither.
Mobo: Intel D945GNT
View 2 Replies
View Related
Dec 29, 2010
I am just now starting to go deeper than the surface of my computer so I am very much a beginner. I have downloaded Ubuntu 10.10 and have tried to install it by mounting the image and installing "inside windows." Next, upon reboot and selecting Ubuntu from the windows loader it eventually went to a colorful screen but stayed there... the first time I let it sit there for 20 minutes or so then restarted, uninstalled/reinstalled tried again... then I let it sit there for 3 hours, nothing. Next I tried to mount image and install "demo and full installation." This time upon reboot I choose Ubuntu from the windows loader menu and an error message came up. I will type it out below exactly as I see it because this is the same message that came up when a friend suggested I boot from a USB drive.
Busybox v1.15.3 (Ubuntu 1:1.15.3-1ubuntu5) built-in shell (ash)
Enter 'help' for a list of built-in commands.
(initramfs) unable to find a medium containing a live file system
View 8 Replies
View Related
Jun 13, 2010
I was trying to install Ubuntu 10.04 LTS on my windows xp. dowloaded and installed wubi. All worked well and system asked me to restart. After restart ubuntu was showing on multi boot screen, selected it. Then the system asked me to ESC installation or not, i didn't Esc. The Ubuntu screen was showing, but all of a sudden an error message saying INSTALLATION FAILED occurred.
My system
Processor: Intel pentium IV
Ram 1 GB
Harddisk:- 160 gb
View 1 Replies
View Related
Jul 3, 2010
i'v installed ubuntu 10.04 on 3 different desktops and 1 laptop. It has gone flawlessly on all 4. i a want to install it on my hp to dual boot(the others i just wiped the drives) but when i tell it to boot from the cd at first it looks like it might work, with the purple page, but after a few minutes, before i get to the install options i get an error message. my current operating systime is windows and i have an hp pavilion. with 2.5 gigs of ram and a descent graphics card.
View 3 Replies
View Related
Mar 28, 2011
My fedora 14 has OpenSSH_5.5p1, OpenSSL 1.0.0a-fips 1 Jun 2010 running. I am able to use putty to ssh to my fedora. I installed NXSERVER - Version 3.2.0-74-SVN OS (GPL, using backend: 3.3.0) but when i used nxclient to connect to the server i always got 'session x' failed.
[code]...
View 1 Replies
View Related
Nov 10, 2010
Im trying to instal Sun Virtualbox but when download completes and I click on install I get the following error>>Message did not receive a reply (timeout by message bus) I wont even bother with this software if there are others out there that are as easy to use. I used it on Windows and thought it was great ! (thats how I eventually switched to Linux, by using it virtually at first)
View 5 Replies
View Related
Mar 30, 2011
I have a single harddisk partitioned with Ubuntu Maverick and Windows 7 installations. I installed Windows first and then Ubuntu, after resizing partitions and adding a new one for Ubuntu. Win7 did not appear in the Grub2 boot menu. I added it (sda3), but on rebooting, I get the message "BOOTMGR is missing/Press Ctrl+Alt_Del to restart".
I understand that Win7 might have put its boot manager in another partition, and sda1 had FAT. I added sda1 as another grub2 entry, but when I try that, I get the error message "Windows Boot Manager/ Windows failed to start. A recent hardware or software change might be the cause... Status 0xc0000225/ Info: The boot selection failed because a required device is inaccessible." Attached are fdisk and parted outputs; and the grub2 files I created. How do I get Windows 7 to boot up?
View 6 Replies
View Related
Nov 22, 2009
I finally did it. I took the plunge and moved away from MS and installed openSuSe on my system. I have a Gateway 650 with 160 MB of ram and yes it did install! To top it all off it also boots to Windows XP. This was all working fine until I < me < myself < yes I am a gonna admit >>USER ERROR<< booted the system into windows and I decided to see if my system needed to be DEFRAGGED. Yup I did.. I ran the defrag on the system and when it was all said and done my NTFS file system was all nice and pretty no more fragmented files.
So I decided to reboot the system to see that wonnerful boot loader of openSuSe and I chose the 11.2 to boot to and I get the message that the previous installation failed and it starts to run the script to "fix" the installation. It hangs on around 4% the installation. I hit ctrl alt del and it boots into the openSuSe partition and it seems to be working, but I have that durn annoying screen of the "previous installation failed". Are there any ideas on how to as my GF 4 yr old daughter says "flix it"? Or do I have to go through the PAINFULLY SLOW installation again?
View 2 Replies
View Related
Jun 19, 2010
(I'm probably going to have my forum account revoked due to excessive usage ) I'm setting a VPN connection on openSUSE 11.2. Using the networking icon on the tray I add a PPTP connection, set it up but I receive a message 'VPN connection failed'. Googling it up I tried changing a setting called 'refuse-eap' to 'yes' but it doesn't seem to work. Here's the result from the log file:
[code]...
View 1 Replies
View Related
Sep 14, 2010
Connect debounce failed port 3 disabled. i get this in the terminal (alt+f1) every time i log on. i like this terminal better than the standard one and i want the error message to stop appearing every time i try to type something.
View 5 Replies
View Related
Apr 13, 2011
I think I'm ready to install Linux openSUSE physical on my Laptop. NO VMware Workstation anymore...But before I can do that I must be sure that Linux works on my System.--- SYSTEM ---
System: TOSHIBA Satellite A300D-13A (PSAK4E-01F00VGR)
CPU: 2x AMD Turion� 64 X2 Mobile Technology TL-64
--- NETWORK ---
[code]....
OK, should be enough for the first, ask if I forgot some Hardware...Because I can't find any driver, and I'm not sure. I'm a LINUX NOOOOOOOOOB!!I really want to install Linux openSUSE, I'm MICROSOFT/WINDOWS HATER since 1 month now!! PS: Wine can't start my favorite Programs like Project64 a N64 Emulator. It fails to start a game! I think the graphic plugin crashes... | The exact error message is: "Failed to extract ZIP Archive" or "Failed to load file".
View 7 Replies
View Related
Apr 29, 2010
Firstly I am new to red5 and not very strong when it comes to linux. I have had installed red5 on my dedicated server and going by the http://myIP:5080/installer demos it is all working fine. My problem is I cannot get it to work with my software being flashchat. I am not sure if it comes from me using the incorrect RTMP url and if so after trying about 20 or more ways of typing it in I always get the same error message "Connection Failed' or "Connection Closed" not to sure what is meant by Closed as to whether it's working but can't get in or what ever. I am after someone who can get this to work for me please and I am willing to pay for that service once it is working.
View 2 Replies
View Related
Aug 30, 2011
Our server is a x86_64 centos 5.5 computer. we installed samba3x-3.5.4-0.70.el5_6.1.x86_64.Samba seems work fine, we don't notice any problem in using it. But in the workstation log file, there are a lot of error messages like:
[2011/08/26 14:37:57.682260, 1] smbd/service.c:678(make_connection_snum)
create_connection_server_info failed: NT_STATUS_ACCESS_DENIED
[2011/08/26 14:37:58.194394, 1] smbd/service.c:678(make_connection_snum)
[code]....
View 2 Replies
View Related
Mar 26, 2010
Ive just installed Debian Lenny and then fglrx and kde, but if i try to login to kde, i get an error message because of invalid user. Do I have to enable my user first to login to kde or something?
View 4 Replies
View Related
Aug 8, 2010
I need to know I/O stats per process. When executed dstat give the bellow error message.
dstat -M topio -d -M topbio
Module topio failed to load. (No module named dstat_topio)
Module topbio failed to load. (No module named dstat_topbio)
CentOS release 5.3 (Final)
uname -r => 2.6.18-128.2.1.el5
How to resolve the above error message
View 2 Replies
View Related
Jun 5, 2010
I ran Movie Player to play .mov file, but it generate the following error message:
pa_stream_writable_size() failed: Connection terminated
The .mov file is wide screen, I am not sure if that's why the error occurred. By the way, the .mov file is several hundred megabytes and store on DVD.
View 5 Replies
View Related
May 15, 2011
When reinstalling ubuntu 10.04, I get an error message that reads "the ext4 file system creation in partition #1 of SCSI3 (0,0,0) (sda) failled.
View 1 Replies
View Related
Dec 4, 2010
I just tried to install Ubuntu 10.04 on my windows machine. Unfortunately there was an installation error and now the computer will not boot up in windows anymore (I get grub error 17). I had Ubuntu 7.04 before, but when installing 10.04, I deleted the 7.04 partitions. Is there a way to recover the ability to boot into windows?
View 1 Replies
View Related
Oct 4, 2009
It's been awhile since I posted anything which is a good sign my install has been working well and I have been able to handle most everything. However, I'm not able to handle this issue. I recently installed F11 and everything went well. But, when trying to see my other computers on the local network, I cannot. I receive this error message: Unable to mount location Failed to receive shared list from server. I understand the message as it is obvious, but do not know how to fix it.
View 14 Replies
View Related
Oct 14, 2010
Subprocess failed. Error: RPM failed: installing package xen-4.0.0_21091_06-0.1.1.x86_64 needs 27MB on the /boot filesystemI seem not to be able to change the size of the /boot, but 11.2 loads okay but not 11.3There only 19MB left from 66 and I can't make it bigger, I hope there is someone thathas seen this. I would like to see some of the update with XEN.
View 1 Replies
View Related
May 28, 2010
I installed lilo and it boots. How do I installed grub again. Do I just use synaptic manager to uninstall lilo and install grub?
[code]....
I know grub2 does not work, giving me error: ntoskrnl.exe missing or corrupt. I did install grub-legacy and it worked, but I had to re-install squeeze due to other problems. So, now I want to replace lilo with grub legacy.
View 4 Replies
View Related
Jan 8, 2010
Update-notifier told me there were updates today and I installed them. Among them were some for chromium (the browser, not the game ). After the update I couldn't start the browser. I tried starting from terminal and got: "Inconsistency detected by ld.so: dl-minimal.c: 138: realloc: Assertion `ptr == alloc_last_block' failed!" "I haz a fail!", I thought to myself and then tried rebooting and then reinstalling. Neither worked. This is on a 64-bit machine. Everything else works as expected. Using Firefox now, but I want my chromium-browser as well.
View 9 Replies
View Related
Apr 9, 2010
Today i upgraded my system and started getting error when i update, install or remove a package. The error isn't restricted only to one repository so i thing something is wrong with my system.
[Code]....
View 4 Replies
View Related
Nov 24, 2010
I'm trying to install ubuntu 10.10 on xp,but, after waiting around 2 hours per instalation I received a error message that says:" unbuntu installer : and error occurred: coercing to unicode: need string or buffer, none Type found. for more information see log file C:1customerlocals-1 empwubi-10.10-rev197.109. I tried on one particion make just for it then I even tried on xp on C: I even put it on a pendrive but my bios is old and do not provide for usb booting. The other thing I have to try is making a boot cd but for one reason or the other , my recorder do not want to recornized my cds- rw and right now I do not have any regular blank cds . That will be my next step. Note: Ubuntu appears installed on the the control panel "add or removed programs" but not in "all programs" list. I'm a novice on this so maybe the answer was posted but I couldn't find it. Looking ahead to try it and be part of the linux team.
View 1 Replies
View Related
