Ubuntu :: Force Add 1440x900 Resolution To NVidia Driver
Jun 30, 2010
My monitor's dvi jack is damaged so my nvidia geforce 210 does not recognise the supported resolutions correctly.
result: while it actually can support upto 1440x900, the highest available resolution is 1360x768.
While on windows, i used the nvidia utility to add the custom resolution and everything was nice.
On ubuntu 10.04, i haven't found a way to do that yet. yes, i searched forums, tried a couple of things with the xorg.conf file and lxrandr, etc. but to no avail.
I did manage to get the resolution listed in ubuntu's own display manager, and it shows 1440x900, but it doesn't apply when i hit 'apply'.
The nvidia settings manager does not show the resolution.
View 2 Replies
ADVERTISEMENT
Feb 8, 2010
I've been loitering over my resolution and nvidia xserver settings for about 2 days now, fiddling with xorg.conf and breaking ubuntu in the process trying to get my resolution at it's native settings. I've searched through many forums and none of them have solved my problem. Its maximum resolution is 1360x768, which isn't enough. It should be 1440x900. I have tried adding custom modes to the xorg.conf file and it wouldn't work. I don't know what's going on. Also here is my xorg.conf since I saved the nvidia settings to it...
[Code].....
View 9 Replies
View Related
Nov 26, 2010
I used Gefoce9400GT , 190.53 nvidia driver, configuring Mulitiple X screen both CRT and TV, work fine if CRT and TV connected to card, but I hope foce TV-out output signal, means that if not connected to TV, the SVIDEO can output signal. Because the line too far, cannot detect TV connection, so I think foce output TV-out signal. I used Option "ConnectedMonitor" "CRT, TV". Can force found 2 display device, have 2 screen ok, but not display at TV if not connected TV. I do not understand why the TV has been forced output signal does not display images, they can be connected to the TV show?
View 2 Replies
View Related
Jun 26, 2010
so I've finally told myself i'd be better off with ubuntu instead of windows. And now I'm seeing I've made the wrong decision. I've spent 4 hours searching the web about how to get the 1440x900, tried some of the solutions and nothing worked. The resolution doesnt show up in the nvidia control panel. I tried somehow editing xorg.conf which just messed everything up so i had to put it in the default state..
View 2 Replies
View Related
May 30, 2010
I run RHEL5 on Dell GX280 with "Intel Corporation 82915G/GV/910GL Integrated Graphics Controller (rev 04)" and i810 driver. But I cannot obtain 1440x900 resolution. Here's my xorg.conf:
Section "ServerLayout"
Identifier "single head configuration"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
[Code]....
View 9 Replies
View Related
Jul 16, 2011
I have installed Ubuntu 11.04 on my Dell Latitude D610 (with ATI X300 graphics card) and am trying to set the default resolution to 1440x900 for my Samsung Syncmaster 931 monitor. I have installed "fglrx" and when I run "xrandr -q" I get the following information.
Code:
Screen 0: minimum 320 x 200, current 1024 x 768, maximum 1440 x 1440
VGA-0 connected 1024x768+0+0 (normal left inverted right x axis y axis) 410mm x 257mm
1440x900 59.9 + 75.0
1280x1024 75.0 60.0
[Code]....
Other posts say I need to edit "etc/x11/xorg.conf" but this file does not appear to exist.
View 8 Replies
View Related
Apr 29, 2010
After update from 8.10 to 9.10 I have screen resolution 1440x900, which is not supported by my monitor. Following changes had no effect on my screen resolution
xrandr:
Code:
$XAUTORITY=/home/zuker/.Xauthority DISPLAY=:0.0 xrandr --output default --mode 1024x768
XIO: fatal IO error 11 (Resource temporarily unavailable) on X server ":0.0"
xorg.conf
Code:
Section "Screen" ...
Subsection "Display"
Depth 24
Modes "1024x768"
Virtual "1024 768"
EndSubSection
View 9 Replies
View Related
May 15, 2010
After having problems with an onboard graphics chipset I've just installed an ATI Radeon 128Mb 9000 Pro AGP graphics card into my old computer... The problem is that I can't get it to use 1440x900 resolution that my LG L194WT (Ubuntu won't detect it) requires and the highest I can select is 1360x768 and that looks all wrong
lspci gives:
Code:
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon RV250 If [Radeon 9000] (rev 01)
01:00.1 Display controller: ATI Technologies Inc Radeon RV250 [Radeon 9000] (Secondary) (rev 01)
And /var/log/Xorg.0.log gives:
Code:
X.Org X Server 1.7.6
Release Date: 2010-03-17
X Protocol Version 11, Revision 0
[code]....
View 1 Replies
View Related
Apr 25, 2011
it will NEVER let me change the screen resolution to 1440x900. It never gives me the option. I then spend hours looking for fixes, making Xconf files and editing them to no avail. The same is true for Fedora 15 (Beta). what can i do to get the 1440x900 option in my "Display" list in Fedora.
View 2 Replies
View Related
Feb 12, 2011
I'm trying to use GRUB2 in graphical mode with 1440x900 resolution, but the result is always garbled nonsense: the highest resolution I can get is 1280x800.
Word is from googling that long as vbeinfo lists a resolution, GRUB2 can use it. This doesn't seem to be true: vbeinfo says that 1440x900 is available but it doesn't work.
Testing it from the GRUB2 command line:
set gxfmode=1440x900
terminal_output gfxterm
# -> garbled nonsense
# back to trusty 640x480
terminal_output console
[Code]....
View 1 Replies
View Related
Dec 20, 2010
I installed Ubuntu 10.10 along side windows 7, It works flawlessly accept for one issue: no widescreen resolution (1440x900).I have some CIBOX screen and XFX HD 6850.
View 3 Replies
View Related
Oct 31, 2009
New install of 5.4 and I have a dell S1909W display that runs 1440x900. I don't run a windowed environment and only use CLI. I am only getting 25 lines per screen with huge text and I need to set the resolution so I can actually work :) I tried adding vga=866 to my /boot/grub/menu.lst file at the end of the kernel line but nothing changes after reboot.
View 2 Replies
View Related
Aug 1, 2010
My native resolution is 1366x768.
View 8 Replies
View Related
Dec 21, 2010
I need to set my resolution to 1280x1024. Problem is, that the NVIDIA X Server Settings does not display such a resolution and I want to use that! My monitor is an LCD capable of upto 1280x1024 75HZ resolution. I'm using Ubuntu 10.10. I did the xrandr command to check what resolutions are available and its output was:
Failed to get size of gamma for output default
Screen 0: minimum 320 x 240, current 1024 x 768, maximum 1024 x 768
default connected 1024x768+0+0 0mm x 0mm
1024x768 50.0 60.0*
800x600 51.0 52.0 53.0
680x384 54.0 55.0
640x480 56.0
512x384 57.0
400x300 58.0
320x240 59.0
In NVIDIA X Server Settings, the list of available resolutions are:
(all of the above)
1152x864
1360x768
I have NVIDIA GeForce 9500GT.
View 9 Replies
View Related
Dec 18, 2010
The nouvea drivers work with some xrandr magic, but the closed-source drivers won't. They fail to detect a possible resolution over 640x480. My monitor has a native resolution of 1440x900 @ 60hz. I've tried to modify my xorg.conf, but to no avail. I installed the latest nvidia drivers from the site instead of the repo drivers, version: 260.19.29, this is my xorg.conf, basically a standard xorg file:
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 260.19.29 (buildmeister@swio-display-x86-rhel47-04.nvidia.com) Wed Dec 8 12:27:39 PST 2010
Section "ServerLayout"
[code]....
View 4 Replies
View Related
Feb 1, 2010
i got nvidia 6150se nforce 430 i install it's drivers from the hardware drivers but the max resolution it gets its 1360x768 which are not enough what should i do to fix it?
View 8 Replies
View Related
Jan 27, 2010
Since I upgraded to 9.04 a while back I have had this annoying screen resolution issue. Every time I log into my Ubuntu system the screen resolution defaults to 1280x1024. My preferred desktop resolution is normally set at 1680x1050. So each time I log in I have to open the Nvidia control panel and manually set the screen resolution to 1680x1050. Even after logging out it will still go right back to 1280x1024 when I log back in.
But the funny this is I am almost positive the login screen resolution is 1680x1050 because the picture is crisp unlike the blurry and distorted picture at 1028x1024. I have tried everything from manually editing the x.org conf file to running the Nvidia control panel as root. Nothing saves my preferred resolution of 1680x1050. My Nvidia driver is version 190.42 and Ubuntu version is 9.04. The monitor is an ASUS VW192T+ which is detected by the Nvidia driver.
View 2 Replies
View Related
Mar 23, 2010
I install on my PC Ubuntu 10.4 and i make al the updates even on my video card I update my video card to the last driver from the NVIDIA official site 195.36.15 My video card is Geforce 8600 GL The big problem is that after the update I have only 2 modes for changing the resolution 320x240 and 680x480 an I relay need biger resolution (1024x786) My xorg.config is :
Code:
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder75) Fri Mar 12 01:42:27 PST 2010
Section "ServerLayout"
[code].......
View 1 Replies
View Related
May 29, 2010
I've just installed 10.04 on my Dell Latitude D830 with a NVIDIA Quadro NVS 140M; upon booting Ubuntu asked me to install the official NVIDIA driver (latest) so I went ahead and installed it, now the boot splash screen is in about 640x480/800x600 rather than the usual 1920x1200 it was when I first booted.
View 4 Replies
View Related
Nov 15, 2010
I am running Fedora 14 on a Dell Lat D630 laptop.
When originally installing my resolution was a perfect 1440x900.
I then installed the Nvidia drivers with:
YUM install kmod-nvidia
This worked fine, I tried out Super Tux 2 to test it and I do indeed have 3D acceleration now. The only problem is my resolution has gone way down. The Nvidia software states its still 1440x900 but it definitely is not... And my monitor is down as (Not in front of it right now so can�t remember exactly) Generic or not detected... Is that what's causing the issue?
So to summarize, I have 3D hardware acceleration, the appropriate Nvidia drivers, it's just my resolution and the fact the Nvidia software is lying about it...
View 2 Replies
View Related
Jan 31, 2011
I am using 10.10 64bit with a Nvidia GeForce Graphic Card on my Acer 5741G 434 Notebook.
I have always used Compiz and without it I can barely use my Notebook. Apparently I had to install the Nvidia accelerated 3d Drivers (current version) in order to use Compiz.
However I cannot enable the "normal" visual effects (right click on desktop / change bakcground/ visual effects) that are necessary for using compiz.
Also everytime I reboot my resolution goes back to 800x600 although I saved the resolution to 1366. So everytime I start my Notebook I have to go to the Nvidia X server settings and set the resolution to 1366.
What I tried until now:
- I tried to reinstall Ubuntu twice!
- I tried to unistall all nvidia Drivers and install through the terminal using the command "sh" the nvidia drivers i downloaded from their website
- I tried to use the nouveau open source driver
Additional Information:
- when I boot a logo of the nvidia BETA driver appears
- for the past couple days I even experienced another problem: the windows do not have the minimize/close and maximize buttons
I am even willing to install the System again!
I had nothing but problems with the latest 10.10 ubuntu distribiution.
View 9 Replies
View Related
Jun 5, 2011
I have installed the Nvidia drivers on my desktop using [URL] according to the Debian way. Everything seems to be fine except the resolution. The best it will let me choose is something like 600x480. I have searched and most of what is suggested around the web is to change xorg.conf. I have tried this using different setting suggested but nothing is working. I did not have a xorg.conf file so I created one with the setting suggested on the Debian wiki.
View 12 Replies
View Related
Apr 19, 2010
New pooter, just installed SuSE 11.1. Would appreciate some insight into which Nvidia driver is right for my system, and what is the maximum resolution I can use without potentially causing any damage (if that's even a real concern).Here are the specifics.
[Code]...
So, now the questions.
a) Should I leave both sets of drivers installed, or should I delete one of them?
b) If delete, which should be taken off?
c) If neither of these drivers is the right one, which do you suggest I get instead?
d) I currently have the resolution set at 1920X1440. Is there any reason to worry that I might be overdriving anything and potentially causing damage to the system?
View 9 Replies
View Related
Apr 26, 2011
I'm new to linux, and i have installed linux slackware 64bit..after a complete setup i downloaded the latest Nvidia proprietary drivers, the binary package from nvidia.com..i have a geforce gts250..it's the first time i encounter this issue..i have already installed the driver with my old monitor (an lg flatron with max 1680x1050)and it always worked fine..with this new monitor (lg w2243s with a res of 1920x1080) it seems that every bin package from nvidia don't recognize the monitor...after installing i find a res of 640x480 and i get stucked, i tried to force it by editing the xorg.conf file..but nothing changes..how can i get the max res with nvidia bin package?
View 3 Replies
View Related
Dec 20, 2010
I recently installed Fedora 14 KDE and NVIDIA proprietary driver for GeForce FX 5200. I'm able to change the resolution to 1920x1080 (Acer H213H 21.5" lcd monitor), but when I restart the box, I lose these settings and I have to fiddle with NVIDIA and KDE monitor settings until I get the settings back.
Here is my xorg.conf file:
Code:
Is this (in)correct? What else can I try in order to keep my resolution at 1920x1080? When I restart, it reverts to 640x480.
I didn't have this problem before installing NVIDIA driver, however, I had visual anomalies and slowness in video refresh/repaint whenever moving windows. I don't want to go back to that so I'd like to see how to permanently propagate my resolution settings through reboots of this box. I've search multiple forums with no relevant hits as far as I was able to discern.
View 7 Replies
View Related
Aug 22, 2011
After installing Debian for the first time earlier today, I tried to setup my display for a 1440x900 resolution. However, the "Monitor Preferences" setting won't allow me to set a resolution higher than 1280x1024.
View 3 Replies
View Related
Mar 27, 2010
So my monitor (a 19" acer) has a native res of 1440x900, which is not detected in display settings. How do I force the resolution to that?
View 2 Replies
View Related
Apr 9, 2011
I am trying to force a resolution (800x600) through xorg.conf. How to do that? The story is the following. I am trying to play a game (theocracy) on my toshiba nb100 (max resolution (1024x600) however the game supports only 800x600 resolution. To play I am using xgame [URL] which has the option to use a separate xorg.conf file to run the game. Even though I created a new xorg.conf1 file which only contains in its "screen" section Modes "800x600" notwithstanding the new screen, with the game is set to 1024x600. How to force 800x600 through the xorg.conf.
View 9 Replies
View Related
Dec 16, 2010
I have my Xubuntu box connected to a 1920x1200 LCD monitor via a KVM switch. If the KVM is set to the Xubuntu box when I boot, all's well, but if the KVM is set to the other machine, Xubuntu boots into a 800x600 resolution. This behavior started with Maverick, when I was running Lucid. the correct resolution was set no matter the position of the KVM switch. Is there some place in Maverick that I need to set the resolution to 1920x1200 so it is set correctly regardless of the KVM?
View 1 Replies
View Related
May 11, 2011
I recently started using Ubuntu 11.04. Everything works fine with my monitor directly connected to the computer. I get a default screen resoluton of 1680 x 1050, which is just fine.
However, when I connect the screen through a video splitter to be able to use a beamer, the screen resolution defaults to 1024x768. Moreover, Ubuntu then detects an unknown monitor and I cannot select a higher resolution.
I searched for modifications of xrandr en xorg.conf but I have to admit I don't understand what I've read. So my question remains: how can I force Ubuntu 11.04 to start with a screen resololution of 1680 x 1050 (without first connecting monitor only, that is).
I hereby add some information I retrieved with the screen connected without the splitter, so you can see what hardware is involved.
Code:
dirk@LaboFysica:~$ xrandr
Screen 0: minimum 320 x 200, current 1680 x 1050, maximum 8192 x 8192
VGA1 connected 1680x1050+0+0 (normal left inverted right x axis y axis) 474mm x 296mm
1680x1050 60.0*+
1280x1024 75.0 60.0
[Code].....
View 9 Replies
View Related
