I just installed 11.04 on my Samsung n130.
It does connect to the router, but when I open a page it does not load it...
It works ok with the ethernet cable.
Edit: after restoring from sleeping mode, it does not see any wireless network, I have to reboot.
I have Kubuntu installed under windows 7. It finds my wireless connection and says i am connected. even with a wired connection it does the same. When i go to the web browser and try it out. says problem with connection. will include some pictures of "iwconfig" and others.
View 4 Replies View Relatedi can open google ..... and many other but when i open opensue webpage and a lot other relate to it. it said problem loading page ,server not found
i also cant do any update or config of theOS that have to connect to the internet
Laptop: HP 6910p Wireless Card: BCM4312 NO issues with wireless in 8.10 (intrepid) - fwcutter driver. Performed clean install of 10.04 (lucid) onto a brand new hard drive (July 2010) - fwcutter driver. NO issues with wireless in 10.04 (lucid) until a few days ago, when. my laptop shutdown because the battery died and I safe-upgraded to 2.6.32-24-generic. Currently I have chronic wireless connectivity issues - slow to non-existent. Ping tests (ping -c6 google.com or ping -c6 4.2.2.1) sometimes reveal 0% loss, sometimes 100% loss, sometimes "unknown host" - within 5 minutes of each other. Regardless of ping results, web pages are consistently slow to load. Skype will also cut out from time to time as the wireless connection vacillates. I have a MacBook Pro which I am using as my (wireless and consistently well-connected) control - and from which I am currently forced to draft this note.
View 9 Replies View RelatedI'm new to Ubuntu and i set up my wireless myself and I think I may have put in wrong settings. I looked through the forum and found these commands to put in the terminal from other posts. Could someone please see if they can fathom what I've done wrong. I have an wG111v2 netgear usb which works fine in windows but is very sluggish on Ubuntu. It worked for a while but since i have deleted and reinstalled my wireless numerous times I now can't get iternet at all. I have Ubuntu 9.10 on my machine which I duel boot with winXP.
ayte@kaytesRocket:~$ sudo dhclient wlan0
[sudo] password for kayte:
There is already a pid file /var/run/dhclient.pid with pid 1927
killed old client process, removed PID file
Internet Systems Consortium DHCP Client V3.1.2
Copyright 2004-2008 Internet Systems Consortium.
All rights reserved.
[Code]..
I have a compaq cq40-133tu laptop. I have windows vista ultimate and ubuntu 9.10 parallely installed. Most of the time i use Ubuntu for programming purpose. But for internet connection i have to go to windows. This is because ubuntu is getting connected to the network but is unable to access internet, whereas the windows can. I want to totally abandon windows. Recently i got internet connection in ubuntu for just 15 minutes or so when i ticked the option AVAILABLE TO ALL USERS. but after that the same story continues and iam not able to access internet. Details about Internet connection: This is not my connection, these signals come from nearby building. Its a wifi open public network.
View 9 Replies View RelatedI've installed Ubuntu 10.04 32 bit version(dual OS) on my 64 bit Pentium core2 duo 2.2GHz processor. Everything seems to be working fine except it's not getting connected to wireless network, although it's detected the network .It was working fine(got connected to wireless network) when I had installed the same OS via virtual machine.
View 9 Replies View RelatedI upgraded to 10.10 the day it came out, and haven't had any problems with internet stuff. My wireless card works without any proprietary drivers. Last night, the computer stopped connecting to the internet. I am still connected to my wifi network, but I can't do anything online. I had assumed that my internet connection was just down in general, and tried resetting the computer, shutting down the computer and then turning it on again, and rebooting the modem, but then my Xbox connected, and my laptop running 10.04 connected, so I'm confused as to what is going in. Any ideas?
View 2 Replies View RelatedI have a WET54g bridge that I am trying to get connected to a wireless network that only allows DHCP. The idea behind it is that I would like to connect the Cat6 out of the bridge to a switch allowing multiple wired computers to connect to the wireless network. The bridge will easily connect to the network once I put the WEP key in, however, there is a kink after that. When I connect the Cat6 to my computer and request an IP for that computer, it self assigns. This tells me that it is not talking to the wireless network through the bridge.
I can not find which IP address the bridge was assigned so that I can talk to it. The sub net is 255.255.240.0 which leaves quite a few possibilities. I know that the bridge is, however talking to the wireless network because the light is steady on the front of it which indicates just that. One other thing to stack on is that I know that there is a "splash page" which comes up when any computer connects. You click on the agreement and then you are allowed onto the network. How can I get my computer to talk through the bridge to the wireless network?
I just upgraded to 10.04 from 9.10 and I ran into few issues.
Laptop - Dell Vostro 1520
OS - Ubuntu 10.04 64 bit
Issue - My wifi connects to the network properly and shows connection established. But I am not able to browse. I tried ping and I didn't got any response. But I was able to get response when I use ethernet (wired connection) and I am able to browse. No issues with wifi card as my wifi is working properly from Windows and with the same network. I did a complete update again before posting this and it is yet to be resolved. Here are the output of some commonly asked outputs with wifi enabled and connected:
1. sudo lshw -C network
Quote:
*-network
description: Ethernet interface
product: RTL8111/8168B PCI Express Gigabit Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
[code]....
I have installed Linux for the first time on an old Gateway purchased from work. The system seems up and running, but I can't get connected to my wireless or the wired network. I have tried using the network manager, but it isn't working. I have tried reinstalling Fedora 12 I have the following LSUSB and LSCPI output.
[Code]...
I am new to this and have no idea what I am to do.....I had Fedora 14 installed on my computer. I have Centurylink as my Internet network. Is there someone who can tell me how to get connected to my centurylink wireless network?
View 4 Replies View RelatedI just installed a dualboot win7/F15 on my laptop (dell XPS 15) and everything seems to be working fine except that when I connect to my network it is connected and the network is accessible (I can visit my gateway/ router) but when I try to visit a website it simply never ends loading it.Internet is working on win7 so it isn't my network's fault.Now I found somewhere that updating could help but since I dont have internet I can't update
View 3 Replies View Relatedanyone knows how to sure files between two suse's connected to ad hoc wireless linux
View 3 Replies View Relatedif i'm connected to my wireless network it only gives me internet acces for a few minutes. The connection with my network stays but i have to close it back of and reconnect before i get back online.
View 1 Replies View RelatedI have installed the latest released version of openSUSE, 10.3 or so, and I am having an issue getting the internet to work. The system tells me that I am connected to my wireless network, but firefox does not browse, indicating that it cannot find the network. I'm totally stumped because if my wireless network is connected, why can't I browse?
View 3 Replies View RelatedI just installed Ubuntu 9.10 in a dual boot Vista system (DELL INSPIRON 530). Everything was ok except the wireless network configuration. Afrer checking on the Internet I realized There was an issue with my network card (Broadcom BCM431. I first tried to install the drivers using Ndiswrapper with not succes. Finally, I was able to use the b43 driver by installing b43-fwcutter. Now the driver is shown and active in the Hardware Drivers Utilily. I am even connected to my Wireless Network. However, I cant load any website. I have checked the parameters in the network set up. I have even tried different options, like static or dinamic IP. But I cant load any website.
View 2 Replies View RelatedI have a Netgear WG511GE PCMCIA card, and a driver from the original installation disk. I used an ndiswrapper-utils gui called ndisgtk to install the driver. I then do the following to verify an installation:
[Code]....
Unfortunately, when I put the PCMCIA card in, nothing happens. On Windows, a green light flashes even if the card is not connected to any network. At first I thought this might be a hardware issue, so I did #lspci and got:
[Code]....
Lo and behold, when I put a different unbranded Wireless PC Card in it works. I'm no expert in Networks, but to me this suggests a driver problem (i.e. the card is physically detected it just won't work). However, the correct driver was installed with ndisgtk and this was verified with #ndiswrapper -l, hence the confusion.
I'd be grateful if anyone else has had this problem/knows of this problem and is willing to share the solution with me/point me in the right direction. So far, Google has returned a few posts from a few years ago talking about patching kernels and manually building files etc (just before Prism54 became integrated into the Linux kernel).
I can connect to my school's wireless network using the standard network manager, but often (not always) it repeatedly disconnects and reconnects every few minutes. Occasionally it also prompts me for the security information again (even after it previously connected successfully).
By running iwconfig when it's on the fritz, I can see that it's often switching access points for the network - which is what I think is causing the problem. It disconnects and reconnects even when the signal strength for the current AP is fine, and it will often switch to an AP with a weaker signal strength.
$sudo lshw -C network
Code:
description: Wireless interface
product: Realtek Semiconductor Co., Ltd.
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:05:00.0
logical name: wlan0
[Code]...
I have internet access using mobile broadband and i also have a wireless network for home usage without internet access.
When my wireless network is connected every application in ubuntu (Meerkat) tries to use it for inernet access (as neededobviously). As soon as i disconnect from the wireless network (and assuming the mobile broadband is on) everything has access to the internet again using the mobile brodband.
How do i tell ubuntu that i don't want it to use my wireless network for internet access?
I have one major problem that is going to cause me to switch back to windows. My wireless network shows connected and works fine for a while but periodically stops working. It always says it is connected but sometimes stops working to where I have to disconnect and reconnect for it to start back up again.
View 9 Replies View RelatedI have a wireless network (192.168.1.0) that's bridged to the Internet and a wired one (192.168.0.0) that's only local. When I am connected to both networks, Natty wants to route my Internet traffic through the wired, local-only one.
Can I make it automatically "just work", so that the right network is chosen for Internet traffic? Otherwise, what's the workaround?
I have installed network controller driver(iwlwifi) in debian jessie and connected to wifi, but I could not connect to any web sites. I installed network-tools and input "iwconfig" it did show a wlan0 there.
Then I opened resolv.conf ,but there were 2 resolv.conf in my /etc,one contains "search lan nameserver 192.168.199.1",one contains "nameserver 8.8.8.8 nameserver 8.8.4.4".
I changed the content of the first one to 8.8.8.8 and restart networking,but I still could not open pages with wireless network.
And I open the first one again,and it changed back to 192.168.199.1,and an extra line "domain lan"above the line"search lan".
Pages do not load on certain sites (such as LinkedIn and Which? for example). The sites themselves load but when I click on links the pages load forever. With Which? I can close FF and open it again and then the link loads but after a few clicks they stop loading. It happens on all browsers (at least I tried FF and Chromium) but OK on Windows.
View 4 Replies View RelatedOut of no where Firefox has just decided to not load web pages anymore. I've restarted my router, restarted my wifi card, restarted my computer, *completly* uninstalled Firefox then reinstalled it, still no luck at all. Anyone have any idea how to fix this? I'm stuck using Google Chrome now, I like it but I need the Add-Ons FireFox has (AdBlock Plus, Xmarks, DownThemAll, etc.)
Here are my specs:
Ubuntu 10.04 64bit
Acer Aspire 3680
Intel Celeron M 1.6GHz Single Core
1GiB RAM
40GiB Hard Drive
Basically all it does is sit there saying "Connecting to www.google.com..." for like 15seconds then gives me one of two pages, "The connection has timed out - The server at www.google.com is taking too long to respond." or "Unable to connect - Firefox can't establish a connection to the server at www.google.com."Google Chrome, Skype, Ubuntu's built in messenger, System Update, and so on connect just fine to the internet.
Yesterday I upgraded from 9.10 to 10.04 using the built in upgrader. After upgrading, whenever I open Firefox, it will just say "The connection has timed out" for every page, but I am connected to the internet. Also, w3m will not load any web pages as well. But I am connected to the internet, because pidgin works, apt-get works, ping, and telnet work.
I will ping google.com with success each time, then attempt to load google.com in Firefox and it will say that it cannot connect to the host. I have tried both "Connect directly to the internet" and "Connect using system proxy settings" for Firefox (the system settings are to connect directly to the internet).
I then thought that maybe something was blocking port 80, so I used telnet (telnet google.com 80), and with that, I got the HTML response of [URL]. what can I do to make my computer able to brows the web again? I am running Ubuntu 10.04 with kernel 2.6.32-22 on a Compaq Presario CQ60-417DX Notebook.
Processor: Intel Celeron 900 @ 2.20 GHz
RAM: 3.00 GB
To see what I mean take a look at the screenshots below.And this screenshot was taken in Windows 7 64-bit of what it should look like.
View 9 Replies View RelatedI can't seem to fire up any web pages but I can do everything else on my ubuntu box. This seems to have started within the past day or so. My /etc/reslov.conf file looks solid.Again, I can ssh, vnc and ping to the outside but just can't load any web pages.
View 9 Replies View RelatedIve just install Midori, and overall I like this browser. But certain pages aren't loading in Midori. Like this forum, Fedoraforum.org. On exactly the same laptop, I can open this page with Firefox. How can I fix this?
View 14 Replies View RelatedI seem to have stumbled on a problem regarding internet connectivity. My web browser (Firefox or any other web browsers) can't completely load the desired webpages like yahoo.com or even google.com.But as I read different blogs in this forum, I have convinced myself that there is an internet connection.= when I ping different websites, Iseem to get good responses from those sites. Only when I need to browse the webpage do get no results.= ifconfig seems to respond well enough.= even "route" shows the IP my router/gateway correctly. The problem , I think, lies on the proxy settings or the DSN.
View 3 Replies View Related
