Ubuntu Networking :: Lucid Wireless - Web Pages Consistently Slow To Load
Sep 21, 2010
Laptop: HP 6910p Wireless Card: BCM4312 NO issues with wireless in 8.10 (intrepid) - fwcutter driver. Performed clean install of 10.04 (lucid) onto a brand new hard drive (July 2010) - fwcutter driver. NO issues with wireless in 10.04 (lucid) until a few days ago, when. my laptop shutdown because the battery died and I safe-upgraded to 2.6.32-24-generic. Currently I have chronic wireless connectivity issues - slow to non-existent. Ping tests (ping -c6 google.com or ping -c6 4.2.2.1) sometimes reveal 0% loss, sometimes 100% loss, sometimes "unknown host" - within 5 minutes of each other. Regardless of ping results, web pages are consistently slow to load. Skype will also cut out from time to time as the wireless connection vacillates. I have a MacBook Pro which I am using as my (wireless and consistently well-connected) control - and from which I am currently forced to draft this note.
View 9 Replies
ADVERTISEMENT
May 26, 2010
I am running dual boot of windows professional xp and ubuntu lucid lynx.I am experiencing a slow network with ubuntu.I am connected through trend net wireless N adapter and dlink 524 wireless router.my network icon is down to 1 bar,25-30% mostly.
View 4 Replies
View Related
Apr 16, 2010
I've enabled LDAP authentication on my 2.2.15 Apache server, but now pages load very slowly. As in, 1.515s with it enabled, and 187.4ms without (just the base page, numbers collected via Firebug). Here's my LDAP config (other directives snipped) -
Code:
LoadModule ldap_module modules/mod_ldap.so
LoadModule auth_basic_module modules/mod_auth_basic.so
LoadModule authnz_ldap_module modules/mod_authnz_ldap.so
LDAPSharedCacheSize 500000
LDAPCacheEntries 2048
LDAPCacheTTL 3600
LDAPOpCacheEntries 2048
LDAPOpCacheTTL 3600 LDAPTrustedGlobalCert CA_DER ssl/ldapserver.der
<Directory "/example">
AuthType Basic
AuthBasicProvider ldap
AuthName "intranet credentials"
AuthLDAPURL "ldaps://ldap.example.com/ou=ldap,o=example.com?mail"
Require ldap-group cn=example,grp,ou=memberlist,ou=groups,o=example.com
How can I speed this up, or at least determine why it's so slow?
View 2 Replies
View Related
Jul 20, 2011
I just installed 11.04 on my Samsung n130.
It does connect to the router, but when I open a page it does not load it...
It works ok with the ethernet cable.
Edit: after restoring from sleeping mode, it does not see any wireless network, I have to reboot.
View 4 Replies
View Related
Nov 6, 2010
I have Kubuntu installed under windows 7. It finds my wireless connection and says i am connected. even with a wired connection it does the same. When i go to the web browser and try it out. says problem with connection. will include some pictures of "iwconfig" and others.
View 4 Replies
View Related
Jan 5, 2010
I can't seem to fire up any web pages but I can do everything else on my ubuntu box. This seems to have started within the past day or so. My /etc/reslov.conf file looks solid.Again, I can ssh, vnc and ping to the outside but just can't load any web pages.
View 9 Replies
View Related
Jun 22, 2010
I seem to have stumbled on a problem regarding internet connectivity. My web browser (Firefox or any other web browsers) can't completely load the desired webpages like yahoo.com or even google.com.But as I read different blogs in this forum, I have convinced myself that there is an internet connection.= when I ping different websites, Iseem to get good responses from those sites. Only when I need to browse the webpage do get no results.= ifconfig seems to respond well enough.= even "route" shows the IP my router/gateway correctly. The problem , I think, lies on the proxy settings or the DSN.
View 3 Replies
View Related
Jan 13, 2009
I have been using Linux via my Acer Aspire One for a few weeks now without any problem. Suddenly I find I can get a WiFi connection but consistently it fails to load the pages. I have tried 2 connections so I know it's my machine. And probably something I have touched. How to reset the the internet settings or better still can I reset the computer back a few days (like in Windows) to resolve this problem?
View 1 Replies
View Related
May 27, 2010
I have a serious problem relating network connectivity under all Linux distributions. I have tried variety of browsers, but the webpages either load partially or do not load at all. Surprisingly, app manager still works well, and I can download apps at full speed from xterminal or app manager. This became an issue which renders Linux distributions close to useless to me. I am currently connected through a router, but direct connection does not solve the problem. What is more, my phone, Nokia N900 is experiencing the same problem with its web browser. I assume, it's due to the fact that N900 uses full Linux distribution. Internet works just fine under all Windows versions (XP, Vista, 7).
View 1 Replies
View Related
Jan 14, 2010
Excuse me if such thread exists already, i carefully searched the forum so i wont create a second one concerning the following problem:So i downloaded (on my new fresh Fujitsu SIEMENS Li3710 running Vista the Ubuntu 9.04 distro.. im a complete Linux noob, but i wanted to give it a second try) so i downloaded it and burned it on the fast laptop, so there wont be any errors caused by low memory during burning I installed and then i went to the Ubuntu desktop - i had all drivers installed. Everything but Amarok sound worked, i turned off my laptop and went doing my job.. The next time i started up my laptop and went on the desktop .. a tradition is to browse the web, so i did that and i couldnt load a single page, except pages with direct IPs i had Skype working just fine and i had a friend there running SuSe and asked him for help. We identified it as a DNS problem, but because of my noobness i couldnt deal with it and i HAD TO switch back to windows, wich i regret so much.
I know that im a noob, but if i have an internet running at its best i can look at forums and resolve my other issues, so im asking for a screenshots on DNS settings so i can fix it the next time i install Ubuntu.Also! I was using cable via PPPoE (and the only terminal command i know is "sudo pppoeconf" ), now im with router, connecting my laptop directly via WI-FI, will i have the same problem and will i have to make settings so i can connect to my router? Because back then i tried to connect to wireless networks and the ones i could connect on XP/Vista/7 i simply couldnt connect on Ubuntu...I really want some real PC knowledge and to use Linux
View 4 Replies
View Related
Dec 7, 2010
I recently upgraded from Fedora 11 to Fedora 14 on my Dell Latitude E6400 notebook PC. It's a Dual core processor, as seen in the uname provided below:
uname -a:
Linux COMPUTERNAME 2.6.35.6-48.fc14.i686 #1 SMP Fri Oct 22 15:34:36 UTC 2010 i686 i686 i386 GNU/Linux
redhat-release:
Fedora release 14 (Laughlin)
Since the upgrade, I've noticed some unexplainable behavior: The load average is consistently 0.5 - 1.75 when my PC is completely idle (99% according to top). No processes are in the D (I/O) state, and I have no Zombie processes. This happens on a fresh boot, every time. It gets worse and less worse, and bounces from unusable (cursor stops moving as I type in the terminal, to actually losing keystrokes at times). I'm wondering if anybody else is experiencing similar issues, or knows of a (the) kernel bug which is causing this behavior? Actively researching the issue. I've come across the following: Tens of wakes per second in "[kernel scheduler] Load balancing tick" on Core 2 Duo even with only 1 core enabled
[Code]....
View 3 Replies
View Related
Dec 14, 2010
I am using BSNL WLL (Wireless Local Loop) on my Fedora system to connect to the internet My modem is Huawei ETS-1201, I use wvdial The problem is that, on every linux distribution I tried, Webpages dont load or load incompletely randomly This happens most during peak net traffic. I tried to edit the /etc/ppp/options file to set my MTU and MRU to 576
But, It does not seem to be working. There is no such problem on Windows and I can connect flawlessly I takes several retries to connect to a site. I sometimes become frustrated with this and switch to Windows But as you all know, Windows is not the right OS for people who want more from their computers.
Below my specs:
Intel Core 2 Duo E8400
Intel BOXDG43NB
1GB DDR2 800MHz RAM
WD 320GB 7200rpm HDD
View 1 Replies
View Related
Mar 10, 2010
I had started another thread about this but had a terrible subject line. Others may have this issue.Found the answer deep in the bowels of documentation. My question now is " did version 20 mess this up for everyone with dialup"?
View 4 Replies
View Related
Mar 4, 2010
I am running OpenVZ.I wanted to use the VPSs IP at a particular port to load the Servers Web Pages e.g. The IP 88.88.88.88 is the VPS IP and 77.77.77.77 is the servers main ip.My files are on the main server at /usr/local/pages/
I want to load the page from the URL: https://88.88.88.88:8888
These should load the files from the main server at /usr/local/pages/ Virtuozzo a OpenVZ panel does it. So how is this going to be possible ? Will DNAT do the trick : iptables -t nat -A PREROUTING -p tcp -d 88.88.88.88 --dport 8888 -i eth0 -j DNAT --to-destination 192.168.0.1:8888
View 3 Replies
View Related
Nov 7, 2010
I just bought a compac presario cq56. I run a live cd of ubuntu 10.04. My wireless network is recognized and connected but when I try to download or view any page nothing comes up.
View 2 Replies
View Related
May 18, 2010
A lot of people have the problem to find themselves with Lucid Lynx 10.04 and experience massive issues when connecting to wireless - me too. As a service, here some relevant links which promise relief:
[code]...
I tried all of them, and none reliably worked. Every solution which required re-association wtih the AP helped for some time, but nothing helped for long. First, don't let yourself fool by the disable IPv6 trap - while it is "enabled" it is acutally not used by Lucid! I have a clean install of Kubuntu 10.04 on an AMD64 Laptop with Broadcom STA driver: 03:00.0 Network controller: Broadcom Corporation BCM4328 802.11a/b/g/n (rev 03) However I can reliably stabilize my connection for some time either by manually disabling WiFi with the hardware switch or disabling WiFi by software means and re-activating. This brings speed at par with Kubuntu 9.10 until some time. Can anybody confirm this behaviour?
View 9 Replies
View Related
Sep 11, 2010
Samba doesn't seem to disconnect on shutdown except by timing out, causing a loooong Lucid shutdown. (I can disconnect manually before shutdown by unmounting the Samba shares, and shutdown is then very fast.) Apparently Network Manager is somehow involved. I've installed a NM shutdown Samba script which works for the first user account, but not for the second user account (which was created and then put into the admin group).
View 4 Replies
View Related
May 3, 2010
I'm an Ubuntu user since Jaunty, and I've always upgraded my system (NOT fresh install). Everything went fine, but yesterday I upgraded to Lucid. My only concern -for now- deals with startup time. I'm a desktop user (Core2@3GHz) so I think I should boot in less than 10 seconds. Anyway, boot time is 30 seconds - not too much, but there is definetly something wrong with tools I don't know (ureadahead, plymouth, etc.). Attached is my bootchart: can anyone explain me what's wrong?
Also, I don't even see a plymouth Ubuntu themed bootsplash: I only see a blank (black) screen standing for seconds, then I see the bootsplash for less then half a second, then GDM appears :S Not crucial -I know- but how can I fix it? (I don't know if it's related, but I can see the animation at shutdown)Finally, GNOME desktop takes too long to load. I don't know why, but there are 15/30 seconds in between login sound and a usable desktop (with panels and icons, I mean).Please help me, I don't want to do a fresh install. Boot speed is not a dial with desktops - I know - but it can be a symptom that my system is a bit a messy (and I don't like it, since I installed Jaunty less then 1 year ago). (!Forgot! I also installed grub2 by hand
View 6 Replies
View Related
May 16, 2010
Since "upgrading" (ha!) to lucid I have had a number of problems that I am working my way through. The latest is accessing samba shares from a Win7 PC. It takes minutes to open the requested share from the Windows 7 PC. File transfers, once the directory is accessed, can be measured in bytes. It is an absolute trickle.
AFAIK the smb.conf is unchanged and, in any case, there is no problem accessing the shares from another linux PC.
View 9 Replies
View Related
Mar 15, 2010
Pages do not load on certain sites (such as LinkedIn and Which? for example). The sites themselves load but when I click on links the pages load forever. With Which? I can close FF and open it again and then the link loads but after a few clicks they stop loading. It happens on all browsers (at least I tried FF and Chromium) but OK on Windows.
View 4 Replies
View Related
May 17, 2010
Out of no where Firefox has just decided to not load web pages anymore. I've restarted my router, restarted my wifi card, restarted my computer, *completly* uninstalled Firefox then reinstalled it, still no luck at all. Anyone have any idea how to fix this? I'm stuck using Google Chrome now, I like it but I need the Add-Ons FireFox has (AdBlock Plus, Xmarks, DownThemAll, etc.)
Here are my specs:
Ubuntu 10.04 64bit
Acer Aspire 3680
Intel Celeron M 1.6GHz Single Core
1GiB RAM
40GiB Hard Drive
Basically all it does is sit there saying "Connecting to www.google.com..." for like 15seconds then gives me one of two pages, "The connection has timed out - The server at www.google.com is taking too long to respond." or "Unable to connect - Firefox can't establish a connection to the server at www.google.com."Google Chrome, Skype, Ubuntu's built in messenger, System Update, and so on connect just fine to the internet.
View 5 Replies
View Related
Jun 30, 2010
Yesterday I upgraded from 9.10 to 10.04 using the built in upgrader. After upgrading, whenever I open Firefox, it will just say "The connection has timed out" for every page, but I am connected to the internet. Also, w3m will not load any web pages as well. But I am connected to the internet, because pidgin works, apt-get works, ping, and telnet work.
I will ping google.com with success each time, then attempt to load google.com in Firefox and it will say that it cannot connect to the host. I have tried both "Connect directly to the internet" and "Connect using system proxy settings" for Firefox (the system settings are to connect directly to the internet).
I then thought that maybe something was blocking port 80, so I used telnet (telnet google.com 80), and with that, I got the HTML response of [URL]. what can I do to make my computer able to brows the web again? I am running Ubuntu 10.04 with kernel 2.6.32-22 on a Compaq Presario CQ60-417DX Notebook.
Processor: Intel Celeron 900 @ 2.20 GHz
RAM: 3.00 GB
View 3 Replies
View Related
Dec 19, 2010
To see what I mean take a look at the screenshots below.And this screenshot was taken in Windows 7 64-bit of what it should look like.
View 9 Replies
View Related
Jan 26, 2010
I have a copy of 9.10 that was downloaded at the time of the official 9.10 release. I don't know if there has been improvements made in this area since then. But but anyone know why 9.10 accesses web pages realllll slowly for me. It seems to boot up normally and web pages load normally but connecting to the web page takes a long time, like 10-15 seconds.
View 4 Replies
View Related
Mar 30, 2010
Ive just install Midori, and overall I like this browser. But certain pages aren't loading in Midori. Like this forum, Fedoraforum.org. On exactly the same laptop, I can open this page with Firefox. How can I fix this?
View 14 Replies
View Related
Oct 23, 2010
I have an odd problem loading certain webpages (not all) from the New York Times in Firefox.
If I try to load this for instance:http://well.blogs.nytimes.com/2010/1...-shoes-or-not/
the page will not load and I see the text "Waiting for graphics8.nytimes.com..." in the status bar.
I did a complete reinstallation of Firefox and it worked fine (yesterday). Today the problem is back again.
I tried the page on a friend's computer also running Firefox in Ubuntu and it worked fine.
I tried it in Windows Firefox and it worked fine.
I have the same add-ons/extensions in Windows as I have in Ubuntu and, in any case, I have removed them all once and tried the page with the same non-result. I also noted that the same thing happens if I try to load the page in Google Chrome in Ubuntu.
View 2 Replies
View Related
Mar 20, 2010
I have apache running on my server, and also Zoneminder, a surveillance system running on the same machine. Both services runs without glitches, and I think apache's config as well as ZM's config are fine. I am not sure I understand how apache (not to mention the whole thing zoneminder, apache, web browser...) works. Pretty hard to manage when you dont know what you are doing. Also, when I try the supposed to work zoneminder webpage in my web browser, I get nothing (a blank page), or sometimes a "Not found" error message. The latest seems to be from apache because it is the same font as the "It works!" message when I try http://localhost:80
The only bit of information I have so far is in the apache error log (/var/log/httpd/error_log) and it says:
Code:
[Sun Mar 21 00:35:14 2010] [error] [client 192.168.0.100] script '/srv/httpd/htdocs/zm.php' not found or unable to stat
[Sun Mar 21 00:46:04 2010] [error] [client 127.0.0.1] File does not exist: /srv/httpd/htdocs/zm
It seems that the "zm.php" is missing.... That would be why Apache cant find the page?
View 14 Replies
View Related
Aug 19, 2010
I have just terminated a program which used almost all my free RAM space, so most pages from other processes are now in swap. When I need to access another process (e.g. browser), it will reload its pages from swap resulting in a lag. I would like to load all the swapped-out pages into physical memory before I need that process, how can I do this (supposing that I have enough free RAM for this)? The only way I'm thinking of is swapoff -a, then swapon -a again.
View 2 Replies
View Related
Jun 22, 2010
So, after installing Lucid wireless doesn't work for me. When I click on the network icon on the status bar, it shows "wireless is disabled".
With that message, I press the wifi button on my HP laptop and it turns off my blue-tooth, without changing the status of my wifi.
I found this rfkill command in another thread:
Before doing anything, after bootup:
Code:
$ rfkill list
0: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
code....
View 2 Replies
View Related
Jan 20, 2011
I have three 10Gb Fibre PCI ethernet cards and 2 onboard gigabit ports. The two gigabit ports always seem to be mapped to eth0 and eth1. I set the network configuration for eth2, eth3, and eth4 in the /etc/sysconfig/network-scripts/ifcfg-eth# files. Would the NIC in PCI slot 1 always be mapped to eth2, NIC in slot 2 mapped to eth3, and NIC in slot 3 always mapped to eth4?
View 1 Replies
View Related
