Ubuntu :: Compaq 311c - Booting After Wireless Driver Installation
Jun 17, 2010
I've decided to try Linux again after a 5 year gap - in around 2005 I installed Suse (I think and I'm not sure of the version) to an Hp laptop and, back then I got hugely frustrated that I had no sound, couldn't for the life of me figure out how to install the driver and gave up after around a week. new company, new laptop, thought I'd try again in 2010 - I'm trying to use the laptop as a work machine mainly, but for dj-ing in an emergency, so I need a 2nd Os and Linux fit the bill. I've got 10 years of It experience, though these days am a Project Manager by day. I've technical enough, but don't have much time.
Naturally I assumed that, by now, everything would be nice and smooth. And, at first, it was - I chose Debian Studio edition (low latency) found a usb linux creator (this is a netbook so no cd drive), Linuxlive usb creator, made up a usb key of Debian 10.04 (desktop edition, as I was informed this was the standard and that I could upgrade to studio after), partitioned my drive, installed and.... Black screen, flashing cursor.
Ok - found some instructions that told me how to work round that...did...but then couldn't get wireless (I've only got wireless internet). ended up, after a day of fiddling with 'blacklisting' drivers, deciding their must be something wrong with my install, so started again with the 'netbook' edition of debian 10.04. This time it boots. Still no wireless.
Now I find people saying things like "blacklist this driver" (b43 and b44) and "connect to the internet and install this driver". Only one problem - only wireless internet - if I go to install more drivers it tells me there aren't any. So I think "I'll install a driver from usb". Naively assuming that by now it'll be a self contained installable package like windows and osx. I find that I need an 'STA' driver (and frankly by now I've spent a long time on forums - this was meant to be easy). Ok - I find the 802.11 Linux STA driver on the broadcom site (can't post links here yet). ownload the 32 bit version, stick it on a key...read the readme and.... Frankly, I'm one step away from trying to roll this all back. I cannot believe I need to be in a 'terminal' typing;
either way, I plough on and get to # insmod wl.ko but it says it can't find it. how to install this driver? Is it even the right one? PS I'm staggered Linux is still so non techie friendly.
I'm new to Fedora, I used to have Ubuntu 10 and found that some software I required would not work properly so I decided to Fedora under recommendation from a friend. I really like it but when I installed Fedora 13 on my Netbook I found it difficult to set up my wireless connection.
No wireless networking. The ethernet works fine, and the wireless interface itself works well in Windows 7 (dual boot). Tried: Ndiswrapper, notoriously quirky, does not seem to work with the XP driver (the oldest driver available for the RTL8191SE). The linux driver offered on the manufacturer's website lacks any installation instructions. I have no clue how to install a linux driver. SUSE seems to have two network managers that are constantly complaining about control: Network Manager and Yast. Neither are great and I am left missing my Ubuntu.
However, my audio only seems to work on SUSE. I have tried almost every distro on this machine. Ubuntu lacked sound and wireless, Fedora played startup sounds, but would not play an mp3 or wav file (fiddling with the mixer did not help). And Fedora also lacked wireless support. PCLinuxOS, my favorite, lacked sound and wireless. Tried some oldies too. ELE, DSL, Puppy, Ubuntu Netbook remix, Vector, Browserpuppy, Crunchbang, Cruncheee (just for experimental sakes) and probably others I am not remembering. So far, installing a free linux distro has cost me 14 dvd-R's and countless hours of installing, reformatting and reinstalling. Part of me really wanted crunchbang to work, as I love the minimalism and blacked-out theme.
I need wireless network access. The wireless light remains red in Linux and pressing the key does nothing to start the device. In Windows 7 it always lights white and works perfectly. Why hasn't SUSE adopted a gui for ndiswrapper? Other distros have it. Why is my brand new laptop, which is by no means abnormal in make or configuration, not 100% supported natively by any Linux distro? I just updated to the new kernel yesterday. So I should be running the most modern operating system available. Yet good-ol Windows 7 is my only fully functional environment.
when I had windows vista on this computer and my wifi went down for good. Well recently my girlfriend was having problems with her wireless and I put ubuntu on it yesterday and then it worked well that made me wonder so I installed ubuntu over my operating system on this computer.
I have not much experience in linux but I have tried most things I have read and when i went to the hardware drivers in the system's drop down a wireless driver doesn't show up I have no driver on here and of course after i wiped the drive and put this system on it i found the Compaq wireless drivers install (not sure if its real or not). I can get on line fine with an ethernet but that is inconvenient to me with the nearest hook up being a bridged network on my brother's computer or the home router which is 30 ft away.
Have been working on a compaq 610 (64-bit) wireless drivers. I have installed all drivers available for wireless devices from its repo but still, the wireless device isn't working. it does fine in windoz.
where i can download driver for my laptop. i just install ubuntu in my laptop and i dont hve how to make my laptop connect to the wireless internet. and i also using ATI radeon graphic card.
It started when I tried to install Kubuntu 10.10. It booted OK from the CD, but after I installed it, it wouldn't boot. It would hang showing "floppy: no floppy found". I think the next part is either initializing swap or disks. No matter what, I couldn't it to boot.
So, I installed with Xubuntu. it worked great, and booted fine a few times. Worked a couple days.
But just today, after updating to the new kernel, it won't boot at all. It gets stuck at the same place!
It does this even if I go back to the old kernel on the boot list.
When I boot into recovery mode, SOMETIMES it will boot. Actually, just once. All other times, it failed to boot even in recovery. I attached the dmesg from one of these boots.
I booted into a puppy partition, and fsck -f my other partitions. It reported no problems.
Could it be a hard drive problem? I don't hear anything from the drive, but it's getting old and I was planning on replacing it soon anyhow.
My computer is a Compaq R3000 AMD64, but I'm running the 32 bit OS.
I installed Ubuntu 10.4 on my laptop compaq presario CQ50 I cannot go online, because the drivers does not exist ? where can I download them? the wireless flash blue by the way, and it was working before I switch to Linux is there anyway to find driver for my wireless compatible?
Sorry for repeating the same old complaint but there doesn't seem to be a common fix: Wireless does not work on my Presario R3000 although SUSE 11.x lists the hardware in the Hardware Information list and the hardware is turned on. Network Manager doesn't display any wireless networks in SUSE while Win 7 can see 4 of them on the same machine. Ubuntu has no problem either
I am running openSUSE 11.3 updated with all the latest patches and I cannot connect to my wireless router. I am running Linux Mint 10 on the same type of notebook HP Compaq 6910p and it worked right after the install. If I take off the security WPA & WPA2 Personal I can connect. lspci -v | less shows this for my wireless card.
10:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61) Subsystem: Intel Corporation Device 1000 Flags: bus master, fast devsel, latency 0, IRQ 29 Memory at e4000000 (64-bit, non-prefetchable) [size=8K]
[code]....
I am using the same settings for both notebooks just can't figure out why openSUSE 11.3 won't connect. I get the prompt to key in my password, I've even checked the box to show password to make sure I was keying it in correctly. Everything was good but it just goes right back to the password prompt after it fails trying to connect.
I am trying to install opensuse 11.2 on my Compaq 610 laptop, I have reformatted the hd and done a clean install of 11.2, however when I boot up the first time (before configuration) it hangs, I have tried both the X64 and the i586 distributions and the only difference is that the X64 distro boots up under failsafe mode while the i586 does not.The problem seems to be at the udev part with the hang up occurring at :
I just finished putting openSUSE 11.4 on my Compaq Presario V5000. I have been trying for hours to find the answer of how to get my wireless card to work. I can't connect to my router wirelessly and the on/off button for the wireless mode does not light up when pressed.
As far as I can tell from what I have already tried, I have a broadcoamm wireless card. It is a bm4318. I have b43-fwcutter installed and I have tried updating my firmware through the terminal. I have also used 'sudo /usr/sbin/install_bcm43xx_firmware'. It appeared successful, but the laptop still cannot make a wireless connection.
Hey everyone I'm pretty new to ubuntu/linux so please bear with me . I recently installed 10.10 on my new htpc. The initial install went great, until I went to install the updated driver for my graphics card. What I did was I downloaded the driver off of nvidia. Then I did these steps:
1. ctrl-alt-f1
2. logged in
3. sudo services gdm stop
4. I then located the driver package that I downloaded and ran it, it seemed to install fine (except for an error about some install script? but it let me proceed)
5. sudo services gdm start
It went to the gdm/ubuntu desktop. However I then connected it via HDMI, and the resolution was way off (top bar was not even displayed on TV) and I tried many different settings but no luck in fixing it. Next after restarting it did not automatically boot to the gdm/desktop. Instead it stayed at the command line login (the ctrl-alt-f1 screen).
tl;dr : 1. How to make it automatically boot to the gdm/desktop after I updated my gpu driver
2. How to fix the resolution for HDMI from my gpu to my TV. (DVI works fine
new Compaq 510 laptop in which we installed Ubuntu 10.04. When Wireless is switched on it shows the available networks but won't connect. It connected on a few occasions but still we can't browse. The proxy settings are correct.Will installing wireless drivers help? If so, where can we find them?
I just got a new Compaq CQ56 and installed 11.04 32 bit on it. Everything is great except the wireless is not working. I can't even get it to detect the wireless card.
iwconfig: no wireless extensions [URL]
Here is the link to the Compaq website. It doesn't say what brand the wireless card is.
I'm totally new to Ubuntu and have just set my laptop up to dual boot. It is an HP Compaq 6720s. I am running crunchbang just now. And am running Ubuntu from the live CD to look at things and familiarise myself.
My laptop has the Broadcom wireless card inbuilt. BUT.. I cannot get Crunchbang or the Ubuntu (8.10) to see the wireless. Is there some little thing I am missing or something that I should set up that I don't know about?
Installed 10.10 maverick on my compaq mini 110, activated the restricted STA driver... But under the networking drop down it shows wireless as enabled but I cannot actually see any networks, there should be about a half a dozen to see. Works fine under windows. Before the restricted drivers are activated ifconfig shows eth0 and after eth0 and eth1 but when I do iwscan eth0 or eth1 it tells me this action is not supported! I have tried reinstalling from cli but no difference?
I just installed a fresh Ubuntu over a Vista install on a Compaq 6720s with Wubi.But the wireless doesn't work in Ubuntu. In Vista everything is still fine.I tried two tips from the help program in Ubuntu, but to no avail. I also tried reseting and restarting. Tried the manual swith on the laptop.
I have a Compaq n610c laptop equipped with a w200 wireless card on the lid of the laptop. Works fine on XP. I recently formatted the HDD and installed Ubuntu 9.10. Wired network works fine and I've updated to the latest updates etc...However wireless won't work. I've followed the instructions onhttps://help.ubuntu.com/community/Wi...ice/CompaqW200. Everything was going fine until I have to compile. I tried the make command and get the following.
On friday (5-28-10) I installed ubuntu 10.04 Lucid, and everything was just peachy, wireless worked and everything.Today (saturday 5-29-10) booted up to find that my wireless wouldn't work. I plugged up to Ethernet and that worked fine, i updated and everything, still no wireless. I google the problem, and have tried everything under the sun to get this darn wireless card to work. I'm pretty sure it's atheros but i am not sure. when i go to system -> admin -> hardware and drivers nothing shows up
I just installer Ubuntu 10.04 Netbook Remix on my Compaq Mini 700EL, the ubuntu website says that everything works very well including the wireless. But for some reason the list of connection doesn't appear at all. It just says "device not ready" This is driving me a little nuts. It appears that the Broadcom drivers are installed. I typed lspci on the terminal and it says that the computer loads a Broadcom Corporation BCM4312 802.11b/g (rev 01)
I also downloaded the drivers even though they should be already in it. But I'm not sure.
I've just loaded Fedora 13 - my 1st Linus system - on my laptop. It went smooth and connected to the net via 'eth0'. But my wireless - an EVO610c Multiport W200 lan card - is invisible to Fedora. A couple of data points are:
I have the NetworkManager applet 0.8.1 (2 pc screens) but don't see the "Network' icon under System->Administration I've read that should exist. I have placed the latest 'Windows' networking file from HP (sp2956.exe) into my download directory. What must I do to 'discover' my wireless card? I suspect the use of "ndiswrapper" and have imported it into Fedora. All updates have been done via 'yum'.
i'm very new to linux(starting), don't know anything. I tried my level best to configure my wifi adapter but, couldn't do it. so give to step wise instructions to to do so.
I've installed CENTOS 5.3 on my laptop, on dual boot with windows xp. The problem is that my wireless network manager doesn't find any networks. Another laptop with fedora 10 installed finds the network, so the problem is not the network. I guess it's a problem with the wireless driver / firmware, as i had this problem on fedora some time ago, and i've solved installing the firmware. Now i've installed the firmware, i rebooted, and it still doesn't find any network.
I recently installed Kubuntu 9.10 in Compaq CQ40 616tu laptop. To connect to internet, the only option i have is via wireless. But the wireless tab is found disabled in it. How to enable it and get it work?
I cannot get wireless to work on my friends HP Compaq 6735s Laptop with Linux Mint 9. The wireless button is lit up. I can use my Desktop USB wireless adapter alright.
