OpenSUSE Wireless :: Wireless Not Working For Compaq Presario
Apr 29, 2011
I just finished putting openSUSE 11.4 on my Compaq Presario V5000. I have been trying for hours to find the answer of how to get my wireless card to work. I can't connect to my router wirelessly and the on/off button for the wireless mode does not light up when pressed.
As far as I can tell from what I have already tried, I have a broadcoamm wireless card. It is a bm4318. I have b43-fwcutter installed and I have tried updating my firmware through the terminal. I have also used 'sudo /usr/sbin/install_bcm43xx_firmware'. It appeared successful, but the laptop still cannot make a wireless connection.
View 6 Replies
ADVERTISEMENT
Feb 12, 2011
I have an Atheros AR5007 802.11 b/g WiFi Adapter. I use OpenSuse 11.3, KDE desktop.When I did iwconfig, it displayed the following:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:"sami"
[code]....
View 6 Replies
View Related
Nov 8, 2010
Sorry for repeating the same old complaint but there doesn't seem to be a common fix: Wireless does not work on my Presario R3000 although SUSE 11.x lists the hardware in the Hardware Information list and the hardware is turned on. Network Manager doesn't display any wireless networks in SUSE while Win 7 can see 4 of them on the same machine. Ubuntu has no problem either
View 1 Replies
View Related
May 29, 2010
On friday (5-28-10) I installed ubuntu 10.04 Lucid, and everything was just peachy, wireless worked and everything.Today (saturday 5-29-10) booted up to find that my wireless wouldn't work. I plugged up to Ethernet and that worked fine, i updated and everything, still no wireless. I google the problem, and have tried everything under the sun to get this darn wireless card to work. I'm pretty sure it's atheros but i am not sure. when i go to system -> admin -> hardware and drivers nothing shows up
View 2 Replies
View Related
Feb 17, 2011
I am running openSUSE 11.3 updated with all the latest patches and I cannot connect to my wireless router. I am running Linux Mint 10 on the same type of notebook HP Compaq 6910p and it worked right after the install. If I take off the security WPA & WPA2 Personal I can connect. lspci -v | less shows this for my wireless card.
10:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
Subsystem: Intel Corporation Device 1000
Flags: bus master, fast devsel, latency 0, IRQ 29
Memory at e4000000 (64-bit, non-prefetchable) [size=8K]
[code]....
I am using the same settings for both notebooks just can't figure out why openSUSE 11.3 won't connect. I get the prompt to key in my password, I've even checked the box to show password to make sure I was keying it in correctly. Everything was good but it just goes right back to the password prompt after it fails trying to connect.
View 3 Replies
View Related
Jul 22, 2011
I just installed ubuntu 11.04 to compaq presario v2000.Everything works except wireless.
View 8 Replies
View Related
Oct 23, 2010
No wireless networking. The ethernet works fine, and the wireless interface itself works well in Windows 7 (dual boot). Tried: Ndiswrapper, notoriously quirky, does not seem to work with the XP driver (the oldest driver available for the RTL8191SE). The linux driver offered on the manufacturer's website lacks any installation instructions. I have no clue how to install a linux driver. SUSE seems to have two network managers that are constantly complaining about control: Network Manager and Yast. Neither are great and I am left missing my Ubuntu.
However, my audio only seems to work on SUSE. I have tried almost every distro on this machine. Ubuntu lacked sound and wireless, Fedora played startup sounds, but would not play an mp3 or wav file (fiddling with the mixer did not help). And Fedora also lacked wireless support. PCLinuxOS, my favorite, lacked sound and wireless. Tried some oldies too. ELE, DSL, Puppy, Ubuntu Netbook remix, Vector, Browserpuppy, Crunchbang, Cruncheee (just for experimental sakes) and probably others I am not remembering. So far, installing a free linux distro has cost me 14 dvd-R's and countless hours of installing, reformatting and reinstalling. Part of me really wanted crunchbang to work, as I love the minimalism and blacked-out theme.
I need wireless network access. The wireless light remains red in Linux and pressing the key does nothing to start the device. In Windows 7 it always lights white and works perfectly. Why hasn't SUSE adopted a gui for ndiswrapper? Other distros have it. Why is my brand new laptop, which is by no means abnormal in make or configuration, not 100% supported natively by any Linux distro? I just updated to the new kernel yesterday. So I should be running the most modern operating system available. Yet good-ol Windows 7 is my only fully functional environment.
View 6 Replies
View Related
Jul 14, 2010
where i can download driver for my laptop. i just install ubuntu in my laptop and i dont hve how to make my laptop connect to the wireless internet. and i also using ATI radeon graphic card.
View 2 Replies
View Related
Mar 17, 2010
I installed Fedora 12 on my Compaq Presario c700 Notebook recently and had a great install. I installed ndiswrapper and installed the inf file for my broadcom 4311 driver through ndiswrapper as well. The installation of the driver appeared to go smoothly.
The only thing is that I still cannot connect to the internet. I aliased the driver as well to wlan0. I can not figure out what is currently the problem. I tried reinstalling the driver and I keep receive a message stating the driver is already installed.
View 7 Replies
View Related
Sep 12, 2010
I installed Ubuntu 10.4 on my laptop compaq presario CQ50 I cannot go online, because the drivers does not exist ? where can I download them? the wireless flash blue by the way, and it was working before I switch to Linux is there anyway to find driver for my wireless compatible?
View 5 Replies
View Related
May 13, 2010
I have a Compaq Presario CQ60 laptop and have one of those wireless light indicators. For me the light glows orange when the wireless is OFF and blue when the wireless is ON. In Ubuntu 9.10 (Karmic) the light was always orange, even if the Wireless was on, but my wireless worked right out of the box so I was grateful for that, but since upgrading to Ubuntu 10.04 (Lucid) I've noticed that my wireless light alternates between orange and blue frequently and sometimes flashes madly when wireless activity is occurring.
I was wondering if there is a fix for this as it can get quite annoying, the light sometimes stays blue for a while but will ultimately keep going back to orange and vice-versa, my friend who also has a Compaq Presario CQ61 (Revised model of mine) has his wireless light constantly blinking orange and blue no matter what.The wireless itself works fine, I can connect to any wireless connection and use it without having to install anything else, so it does work out of the box, which again, I'm grateful for.The wireless adapter is a Atheros AR5001 Wireless network adapter. Do I need to install additional packages or drivers to get the wireless adapter to work properly?
View 9 Replies
View Related
May 26, 2009
I installed SLED 11 (and openSuse 11.1 as well) but the wireless button(WIFI ON/OFF) which is next to power button of my laptop does not work. It worked in vista (formatted the HD and installed SLED 11 as soon as I bought the notebook ) the wireless driver is Ath5k. The button should actually light up the LED and if the Wireless card is active LED should be BLUE, and ORANGE if the wireless is disabled.. Now its always ORANGE!
I tried to capture the hardware address of the LED but it was a failure! (previously I configured Touchpad ON/OFF switch by myself writing a small script after retrieving values from dmesg)...
So the main issue I have is WIFI On/Off switch (and LED) doesn't work well...
View 2 Replies
View Related
Jun 10, 2011
i cant seem to get my mic to work i just installed ubuntu 11.04 on my copmaq
View 3 Replies
View Related
May 25, 2010
I have an older Compaq Presario S6000CL, specs for it are here:
*Product Specifications Compaq Presario S6000CL Desktop PC - HP Customer Care (United States - English)
Motherboard and bios here:
*Motherboard Specifications, A7V8X-LA (Kamet 2) Compaq Presario S6000CL Desktop PC - HP Customer Care (United States - English)
I am trying to get SME Server set up as a private server/gateway. Problem is no matter what I do I can only get one ethernet working at a time and only to the internet, not the local network. I tried both SME Server 7.4 and 8.0 beta 5 witht he same result. Now of course I checked the ethernet cards. The two I have now on it do work. One of them is the onboard ethernet the other one is in the second pci slot. They jsut don't work at the same time. (also I am familiar with SME and I had it configured correctly. Even if I messed up the order of the cards it is easy enough to just get up and switch the cables, reboot, etc.) I thought maybe there was a jumper setting or an over ride of some sort to let me use two ethernet cards. <I previously had all of this set up with an old HP computer (came with windows 98 originally.) But that computer decided it was time to retire to the road side.> It seems that it should just work. Any ideas on what I am missing or what I can do?
Edit:Spent another hour trying to get it to work and still nothing. It is picking up both ethernet cards just fine, I just updated sme 8 beta5 so the internet is working fine. I just can't get the local ethernet card to do anything at all, even though it is showing up as a green ok at boot. I checked the bios and I am not seeing anything there. It had an option to enable/disable LAN (which is enabled but I tried both and using to PCI ethernet cards. Didn't do anything different.) It has a Local LAN boot rom option, tried it enabled and disabled (Disabled now.) and nothing. I turned off the serial and parallel ports (doesn't make a difference either way.) I looked all over the motherboard and the only thing I can find is the jumper to reset the password. If a computer that was at least 12 years old could run SME and don't see why this one can't, it is half that age and a much better computer hardware wise.
View 9 Replies
View Related
Jun 13, 2010
I acquired an older hp compaq presario computer version 6310us, and initially installed mint, followed by Ubuntu 9.04. Neither one recognized the onboard ethernet port. I checked the bios, and LAN is enabled. It is also enabled in the drop down menu from the toolbar on the desktop. The cable works fine on other computers, and the light on the ethernet port flashes like it does when the cable is connected. I'm new to linux, so not sure what to do to get the connection working.
View 2 Replies
View Related
Dec 18, 2010
I have this laptop, and I managed to find only the .sys and the .inf file for ndiswrapper.It worked, but it said that the firmware is missing. Was this supposed to be a .bin file?
I want to use Ubuntu on my laptop, but I'm really struggling.
View 1 Replies
View Related
Feb 27, 2010
I just installed helena on my compaq presario cq61-223sa but i can't get the altec Lansing speakers to work and my internal mic as well. I'm fairly new at linux and have tried looking for drivers but i couldn't find any.
View 4 Replies
View Related
Sep 19, 2010
new Compaq 510 laptop in which we installed Ubuntu 10.04. When Wireless is switched on it shows the available networks but won't connect. It connected on a few occasions but still we can't browse. The proxy settings are correct.Will installing wireless drivers help? If so, where can we find them?
View 1 Replies
View Related
May 2, 2011
I just got a new Compaq CQ56 and installed 11.04 32 bit on it. Everything is great except the wireless is not working. I can't even get it to detect the wireless card.
iwconfig:
no wireless extensions
[URL]
Here is the link to the Compaq website. It doesn't say what brand the wireless card is.
View 9 Replies
View Related
Mar 20, 2010
I have a Compaq Presario 7588 It has a PIII at 550 mhz
512 MB Ram
a 30 GB HDD
a DVD drive
and a very weak graphics card (8MB or 16 vram). Is this enough to run opensuse and use KDE?
View 5 Replies
View Related
May 19, 2009
I've installed CENTOS 5.3 on my laptop, on dual boot with windows xp. The problem is that my wireless network manager doesn't find any networks. Another laptop with fedora 10 installed finds the network, so the problem is not the network. I guess it's a problem with the wireless driver / firmware, as i had this problem on fedora some time ago, and i've solved installing the firmware. Now i've installed the firmware, i rebooted, and it still doesn't find any network.
View 1 Replies
View Related
Jan 3, 2010
I have a Compaq n610c laptop equipped with a w200 wireless card on the lid of the laptop. Works fine on XP. I recently formatted the HDD and installed Ubuntu 9.10. Wired network works fine and I've updated to the latest updates etc...However wireless won't work. I've followed the instructions onhttps://help.ubuntu.com/community/Wi...ice/CompaqW200. Everything was going fine until I have to compile. I tried the make command and get the following.
Errors:
make -C /usr/src/linux-headers-2.6.31-16-generic M=/home/gsoo/usb KERNELRELEASE=2.6.31-16-generic modules
make[1]: Entering directory `/usr/src/linux-headers-2.6.31-16-generic'
[code]....
View 3 Replies
View Related
Apr 24, 2009
After several hours of frustration to point of almost scrapping linux alltogether I was finally able to get my wireless networking to work in Linux Mint 6. I searched for hours and came up with several different suggestions that were supposed to fix my problem - NONE OF THEM WORKED! As a new linux user, I can completely understand why so many people try linux and then give up on it. It should not be so hard to get a wireless internet connection working.
Said another way - the people making distros should read these forums and see what difficulties are experienced and work on fixing them. In any event - I want to post my solution to the problem for my COMPAQ CQ60-211DX so that anyone else who wants to try linux on this model laptop will save a great amount of time. Here are the steps I took to get linux mint 6 to work on my laptop:
1. Open terminal window
2. Type - lspci | grep Atheros
3. Hit the enter key
If you see: Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01)
then these instructions WILL get your AR242x (AR5007) wireless card to work for you. Be warned - I tried everything I read including ndiswrapper, etc. - none of it worked! You will need to click the menu button go to all applications and then administration. From there, select hardware drivers and look for anything that has Atheros in it. CLICK DEACTIVATE! Now you will have to restart your computer. When it starts back up....
View 2 Replies
View Related
Jul 28, 2010
i'm very new to linux(starting), don't know anything. I tried my level best to configure my wifi adapter but, couldn't do it. so give to step wise instructions to to do so.
View 8 Replies
View Related
Oct 24, 2010
After having scoured the internet and the forums for advice, I am still not able to connect via Wireless, which is being controlled by Network Manager.The following is info I obtained from running a script that I obtained reading these forums:
* Hostname: linux-8qpz.site
* Run date and time: Sun Oct 24 10:12:58 EDT 2010
---------------------------------------------------
[code]...
View 3 Replies
View Related
May 24, 2011
i read the sticky post on here about how to try and get my wireless card working.
i have installed opensuse 11.4
i followed step 1 of post and got following: /usr/bin/lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[code]...
View 9 Replies
View Related
Sep 4, 2010
My openSUSE's working unstable and very slowly! Wireless is starting very late.It appears 10min later after i loggen in,and wants me to enter wireless password.This windows is showing up so late,and I can't connect internet before it shows up.
View 4 Replies
View Related
Jul 8, 2011
I have just installed openSuse 11.4 KDE 64-bit on a Dell M1330. When I click on my networking panel, it says WLAN interface is unavailable. I've followed the steps in the stickied post and found the WLAN hardware info, a screenshot of which is below:Uploaded with ImageShack.usNext it says to do this - you need to look at the logs, in particular the info in /var/log/boot.msg. To see this, you need YaST => Miscellaneous => System Logs and select boot.msg.In YaST there is no such option for system logs under miscellaneous, so I can't do that. The results of the sudo /usr/sbin/iwlist scan command produce the following:
root's password:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
[code]....
View 9 Replies
View Related
Jun 6, 2010
The wireless on my 64-bit openSUSE-11.2 installed on my Dell Studio 1537 laptop stopped working some time back (possibly more than a one or two months back). I just discovered this last week when on business. I have not used the wireless under openSUSE-11.2 for a while so I am not certain what broke it, but I am suspicious of an update. I note openSUSE-11.3 milestone-7 works great with the wireless (on a liveCD). I note possibly two related threads, although I note no failed request for firmware in my case:request for firmware file 'iwlwifi-5000-2.ucode' failed [INTEL 5300 AGN] [OPENSUSE 11.2] - openSUSE Forums, and I see another thread here: Suddenly No Wireless Network Card - openSUSE Forums... but I can not tell if what I have is the same problem, so I did not add to those threads. In my case I can scan for the network, and see the SSID. An ip address is assigned. But a ping does not work.
Some details, the wireless is:
Code:
04:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5300 AGN [Shiloh] Network Connection [8086:4235]
Subsystem: Intel Corporation Device [8086:1121]
Kernel driver in use: iwlagn
In terms of installed apps:
Code:
rpm -qa '*wireless*'
wireless-tools-30.pre8-5.1.x86_64
wireless-regdb-2009.09.08-2.2.noarch
[code]....
I know the router wireless network is good, because I can connect to the router via wireless with another laptop (old Fujitsu-Siemens Amilo 7400M with older Intel wireless), and the router wireless also works with this Dell Studio 1537 PC (with same hardware) but with openSUSE-11.3 milestone7 version.
View 9 Replies
View Related
Mar 31, 2011
I have Lenovo G550 and openSUSE 11.4. Everything's ok, wifi without problems, I could connect to anywhere I wanted to, but yesterday while laptop was running and was connected actually by wire to internet, after removing the wire I realized that I cannot connect to wifi (the laptop was hibernated during night) - even the light diode in the front of the laptop was not shining. I went to yast and realized that the wlan0 isn't enabled and there's new eth1 port. But the wlan by ifup I cannot start and the eth1 I cannot start as well.
View 4 Replies
View Related
