I have created a VPN through network manager to a Windows 2003 server.
However when I try connecting it fails every time, I have tested with a windows XP client and this works so this would indicate I am doing something wrong in the network manager configuration.
I need to setup a Linux VPN server at work for resources' sharing, I currently have a server running CentOS 5.4, and tried endless tutorials on the web, but to no avail, and can't find where the logs are kept for the VPN server to check where the error is. But all my attempts to try to connect keep failing.
View 9 Replies View RelatedI have set up a nis slave server on Fedora 14. It was set up on a laptop so that the user can log in when he is at home (no NFS, local home dir). However, whenever the eth0 is disconnected, ypbind fails.
I have tried the same setup on a RHEL 4 (configured it as a slave server) against the same master nis as on the Fedora 14. Disabling eth0 on it however does not fail ypbind.
I have done a fresh install of the OS and I am having wifi trouble. I am failing in connecting to an access point that Windows works fine with on the same machine. As far as I can tell it is connecting but not getting an IP address via DHCP. when running ifup it says its backgrounding getting an ip address.
View 9 Replies View RelatedI seem to be having a problem with mod_proxy and https websites. A simple connection to port 80 works fine but all calls to 443 fail.
I had a look at my firewall but can't see anything that would block port 443, although I get no tcpdump traffic on that port on the deb01 client when I try and connect to it. I disabled the firewall but still no luck.
My configuration consists of 3 VMs (KVM) each running a different website.
I get the following error when connecting to ssl deb01
Code: An error occurred during a connection to deb03.example.com.
SSL received a record that exceeded the maximum permissible length.
(Error code: ssl_error_rx_record_too_long)
The following is what can be found on the host
Code:
I have a Redhat fedora core release 6 (2.6.22.9-61.Ns4) server and form time to time ssh fails although I am still able to ping the device and with a reboot the device will start working correctly so upon further investigation it appears the sshd daemon fails.Not knowing a great deal about Linux I thought I would ask some advice on the path I am thinking of taking. The first would be to put an entry in the cron to try and start the ssdh every hour or so. Would this cause issues in the long term run it multiple times when the sshd daemon was still running?
The Second though I had was having a bash script to check if the process was running and if not restarts it and if it was just exit the program which would seem like a neater way to do it but this is where my limited Linux knowledge hits a wall so was looking for suggestion on how to implement this?
I'm a light linux user over the last couple of years and I decided to built a HTPC/NAS device.
Setup:
40gb ide -> usb boot drive
3x2tb sata (4k Sector) drives
I've got another 2tb identical drive but it's holding data that is going to be copied to the raid after it's up and running and then be 'grown' into the raid array to yield a final 5+tb array. I tried doing a disk util raid array and it ended up failing after reboot due to it using the /dev/sd* designations and they swapped. I have no idea how to do the UUID version, my googlefu and practical guide to ubuntu. So I decided to do it manually in order to also fix the sector issue as disk util wasn't formatting them correctly and once formatted wouldn't let me create a raid array from the discs.
[Code]....
I seem to have a complex issue on my hands that i can't figure out. first, i wasn't able to get access to my LVM'd hard drives via SSH without half of the content being missing or locked out (read-only or unable to open at all). the problem then went up to being unable to boot up - all i got was a long slew of [100.1234] ata1.00: error messages (they eventually DO stop once they get to around 998.234234 or whatever, and then i can log in and it seems to be "stable").
Part way through this rebooting ordeal i realized / decided to make power-on-self-test stop and wait if it finds errors (via bios) - that showed me that my 750G SATA drive is "bad" and my two (older) 120G & 250G IDE drives are "ok". i then unplugged the SATA drive, rebooted, and didn't see those error messages. however, my LVM was still obviously not coming together (since LVM was made up of the 120G, 250G, and 750G drives)
So, now it seems:
a) I can't boot smoothly with all drives in place
b) I can't do anything with lvm if i remove the 750G sata
c) With all drives hooked up, i can wait 10mins for the errors to go away, but STILL can't do anything with lvm
d) I need to recover the lvm stuff so that i can nicely migrate ALL those files (1.1TB of it) onto a new 1.5TB drive and do away with lvm
This is all running ubuntu 7.10 server edition (32-bit version on a 64-bit computer). i DID post a question on the ubuntu forum as well but so far got no replies at all.
Here's a few pics of the booting process, with one or two "fail" lines showing.
I was trying to setup userful on my laptop, but it keeps failing to start the x server. I have a card that can support it.
View 7 Replies View RelatedFor some reason my DNS servers aren't able to resolve certain names. Most names resolve fine there are just a few that don't work. Nslookup doesn't work either of course, and curiously neither does "whois".
Here's an example:
Quote:
dig facebookmail.com +trace
; <<>> DiG 9.2.4 <<>> facebookmail.com +trace
;; global options: printcmd
[code]...
I added the "@clustering" and "@kvm" keywords to my ks.cfg file but during installation, an error about not being able to find either of these packages popped up and it wasn't installed.
I do see the Cluster and VT directories in my redhat_es5.4 directory along with the Server directory. The rest of the files install just fine.
In doing some net and forum searching, I find a reference to a base.repo file that lists the directories but I'm not sure if it's related to creating a yum repository or if not, should it have been created in the redhat_es5.4 directory.
While I've built kickstarts for several years and am comfortable with the file, this is the first time I'm working with rpms outside the main Server path.
I can't upload photos to facebook and I'am using Squid
It gives me this
ERROR The requested URL could not be retrieved
While trying to retrieve the URL: [URL]
The following error was encountered:
Read Error
The system returned: (104) Connection reset by peer
An error condition occurred while reading data from the network. Please retry your request.
Your cache administrator is webmaster. Generated Sun, 24 Oct 2010 20:24:00 GMT by hermanon (squid/2.7.STABLE3)
I have a KVM server and am trying to add a new VM. The problem is I am unable to connect to the consle to finish the installation. I have put the details of the steps I took and my ssh config file for clarity. It seems I have a problem with a vnc 'security type'.
ssh config
Code:
Port 2200
Protocol 2
HostKey /etc/ssh/ssh_host_rsa_key
HostKey /etc/ssh/ssh_host_dsa_key
UsePrivilegeSeparation yes .....
Code:
$ virt-manager -c qemu+ssh://root@phoenix:2200/system
[Prompt for password and connects OK]
KVM Server
Code:
# virt-install --connect qemu:///system -n web -r 1024 --vcpus=1 -f /dev/vms/web_os -s 5 -c ~ecosta/debian-504-amd64-netinst.iso --vnc --noautoconsole --os-type linux --os-variant debianLenny --accelerate --network network:default --hvm
Starting install...
Creating domain... 0 B 00:00
Domain installation still in progress. You can reconnect to the console to complete the installation process.
client
I can see the new VM but when I chose to open the console, the password is asked again and again without a successful connection to the console. The following is what I found in the log.
virt-manager log: .....
I then tried to make an ssh tunnel and use vncviewer to connect:
Code:
$ ssh -p 2200 root@phoenix -N -T -L 5902:localhost:5902
Code:
$ vncviewer localhost:2
Connected to RFB server, using protocol version 3.8
Server did not offer supported security type
Code:
$ ssvncviewer localhost:2
Proto: RFB 003.008
Connected to RFB server, using protocol version 3.8
Server did not offer supported security type:
sectype[0] 19
Security-Type: 0 (rfbSecTypeInvalid) Latency: 12.40 ms
ShmCleanup called
VNC Viewer exiting.
I just upgrade from 10.3 to 11.4. Everything went fairly smoothly and most things are still working execp nfsserver
getting:
/etc/init.d/nfsserver start
Starting kernel based NFS server: mountd statd nfsdrpc.nfsd: writing fd to kernel failed: errno 13 (Permission denied)
rpc.nfsd: unable to create inet6 TCP socket: errno 97 (Address family not supported by protocol)
rpc.nfsd: unable to set any sockets for nfsd failed
dmesg:
RPC: server localhost requires stronger authentication.
[ 2545.282736] svc: failed to register nfsaclv2 RPC service (errno 13).
[ 2545.282742] nfsd: last server has exited, flushing export cache
[ 2545.282852] RPC: server localhost requires stronger authentication.
[ 2545.282955] RPC: server localhost requires stronger authentication.
[ 2545.283848] RPC: server localhost requires stronger authentication.
[ 2545.283957] RPC: server localhost requires stronger authentication.
we have a server that runs a backup (cron job) at 9:15 every night. When I log on in the morning I have mail message that gives me a long list of all the files that were backed up the night before. For a couple of weeks now, the mail message gives me an empty list. Yet, when I run the same job manually from a #prompt, it runs. I am not able to run this job with cron in the daytime because too many users are in it. I wanted to browse the tape to see if the backup is really failing to copy the files or if they are on the tape and the mail message is bogus.
Since the backkup was done with cpio instead of tar, I'm not sure if I can browse the tape with restore -i anyway.What would be the best way to browse the tape on /dev/rmt/1 without actually restoring anything ?This is an ancient DGUX system, not Linux, and I'm not a unix expert I just inherited this server recently, but a lot of things are very similar to Linux and it looked like this might be a good place to ask.
I am trying to connect the one of server RHEL5.4 to the IBM iSCSI storage. Server is equipped with 2 single port Qlogic iSCSI HBA(TOE). RHEL detected the HBA and installed driver itself (qla3XXX). I have configured the HBA ip address in the range of iSCSI host port of storage. Both of the HBA is connecting to the two different controller of storage. I have discovered the storage using command iscsiadm -m discovery command for both of the controller and it went through fine. But problem is whenever server is restarting if both of the hba is connected to the storage then server will not detect the volumes which is mapped to the server and then to detect the volume I need to run "mppBusRescan" and "vgscan" command each time. If only one path is connected it is fine.
View 1 Replies View Relatedi want connect ubuntu server to windows and retrive mysql from windows
View 8 Replies View RelatedIn trying to help our office modernize its IT infrastructure, one of the key components is maintaing our server. We have around 50-60 people who need access to a local server primarily for secure general file storage. These employees are geographically dispersed. We currently use some(?) version of Windows Server which is maintained and updated by a IT company we keep on retainer. After doing some very basic research on Ubuntu Server, I would like to try and incorporate a pilot program utilizing the Ubuntu Server software.I was successful in installing Ubuntu Server on an unused PC that I put a clean hard drive in. I have been following the direction of the Official Ubuntu Server manual to assist in the server setup, and this has progressed my cause up to a point.
Can I run an Ubuntu Server alongside our current Windows server without bring everything to a screeching halt? Additionally, I am the only mac computer in an office filled with varying version of windows. I have begun to configure samba but need some direction from the community as to updating the workgroup so my mac can connect to the Ubuntu Server. What do I need to put in the workgroup part of the /etc/samba/smb.conf directory?I have no doubt there will be face palms by the community after reading this thread, but I am trying my best to teach myself the Ubuntu way.
I know little if anything about svn, so need your assistance. I have a linux server running svn. I have a Windows server running svn. First, I'm looking for a way to copy an svn repository from the linux server to a new Windows server repository. I've looked for how to do this on the Internet and within the Apache.org website(which is now the maintainer of SVN).
I haven't found anything on a very granuler way to copy a repository from one O/S to another other than folks say it can be done. Not how.
Second, is there a way to automatically do this on a regular basis? I see the manual process of svnadmin dump and svnload. Also there is a manual process of svnadmin hotcopy.
Wanting to join my CentOS5.3 to a windows 2003 active directory. Configured kerberos and samba.
Code:
[libdefaults]
default_realm = domain
dns_lookup_realm = false
[code].....
I want to setup a Linux File Server for a small windows network (around 50 users). I do know that I am gona need Smb service/pkg for that. I haven't used Samba for a while now and as per the best of my knowledge, entire communication (including usernames and passwords) between a samba server & windows client machines will be plain text. Is there any way to secure all this communication??
Secondly, if i remember correctly, MS windows wont let me mount more than one samba shares as network disk when all my shares can be accessed by different smb users with different passwords?? is there a solution to this problem? OR may be if there is any other package available for this purpose so that i wont have to use samba?
I'm trying to rsync files and directories from a RedHat linux host(v 4.5 & 4.7) to a Windows server 2003R2 Standard Edition with cygwin running. I'm executing the rsync command from the cygwin shell. The transfer involves rsync'ing approximately 1 TB of data from the linux server to the windows server. After about 280+GB of data transfer, the transfer just dies.
There seems to be no particular file or directory that the transfer stops at. I'm able to rsync GB's of data from other linux hosts to this cygwin server with no problem. Files and directories rsync fine.The network infrastructure is essentially the same regardless of the server being rsync'ed in that it is GB Ethernet running through Cisco GB switches. There appear to be no glitches or hiccups across the network path.
I've asked the folks at rsync.samba.org if they know of any problems or issues. Their response has been neutral in that if the version of rsync that cygwin has ported is within standards then there is no rsync reason this problem should happen.I've asked the cygwin support site if they know of any issues and they have yet to reply. So, my question is whether the version of rsync that is ported to cygwin is standard. If so, is there any reason cygwin & rsync keep failing like this?
I've asked the local rsync on linux guru's and they can't see any reason this should fail from a linux perspective. Apparently I am our company cygwin knowledge base by default.
My Pug Server has worked faithfully for many years just sitting in a closet. It is designed wo that you never need to add a monitor or keyboard as it is administered through a web interface. Recently it had a problem with the motherboard and I had to replace it, but the machine is now working. However, it no longer is visible as a network drive on my Windows machine.Unfortunately I have no idea where to start looking to see what the problem is. I did attach a keyboard and monitor and logged on, but everything looks okay (I can see my files, etc.).
This is an old machine (c. 2003), so has an old version of Linux (I have no idea what version, or even how to find out). Since it is never meant to be used directly it doesn't have any GUI installed, so I have to do everything using command line.Does anyone have any suggestions as to how I can even start to determine what the problem is or how I can go about trying to fix it? At this point I would be happy just to get the files out and replace it with a newer NAS.
My desktop is running 'buntu 9.10 and I have recently aquired a couple of half decent servers running Windows server 2003. I have a few windows app's that I use regularly for work that I have had limited success in running with wine or in vm's. I stumbled upon a how to to call apps in a vm to run seamlessly on the host desktop and did some playing and have succeeded in calling app's on my servers from my 'buntu desktop, the command I have set in my launcher for one of them (DIALux)
My question is, can I change the default application/file association in 'buntu with a custom command so I can double click on a file and have it open in one of these remote app's??If I can, what is the correct custom command to be using as using the above doesn't work at all, it just tries to open the file with rdesktop not the remote app.
I have a CentOS + Samba server and Windows XP client machines. Users, passwords and permissions are entered on the server machine.users and passwords ( same as on the server ) are entered in the XP client machine.When attempting to access a public file on the server using a XP client machine and the IP address of my server, I am asked a user name and password and none of the already entered seem to work. I cannot access the server file (prompted again and again to enter user name and password). What did i miss
View 7 Replies View RelatedI need to install FTP Server in CentOS and it has to integrate with Windows 2003 Active Directory. Users should use their Active directory Credentials to upload or download files in FTP Server.
View 3 Replies View RelatedHow to configure linux vpn server for windows clients & roadwarriors connection?
View 4 Replies View RelatedI currently run Windows Server 2008 at my office, but I'm looking to test Samba as a PDC for future reference/consulting work. Before I go and try to configure Samba, I wanted to ask if anyone can think of pitfalls I would run into and perhaps recommend a better setup:
<10 PCs running either Windows XP, Vista, or 7.
VirtualBox running Debian (planning on swapping for Fedora) on a Windows XP Home computer.
Computers are connected to a large switch, which is connected to a wireless router. The Windows server doesn't employ ICS (essentially is just a $1500 PDC ). where I could find a .ovm format image of a windows server installation? I'm guessing vmware would work in this regard, but I'm not fond of using purposely crippled software.
this is vinoth. im using redhat el5 . i want to migrate windows 2003 server active directory with redhat linux el5 2.6.18-8.el5
View 2 Replies View RelatedI have an issue with users logging into a server. There are multiple (5 or so) database admins that have to log into a windows 2003 server and from there log into a red hat server. Once they are in the rhel box they execute an app (let's say xclock) that gives them an xwindows session on their desktop. Currently only one person can do this at a time, but they have asked me to configure it to allow multiple users to log into the red hat box from the windows server and run an xwindow.
View 6 Replies View Related