I just installed Debian Lenny on my new laptop, I uninstall network-manager and install wicd but, it looks that wicd when it scans for networks doesn't find any networks and I don't understand why. I look over my sources.list and it looks ok, then I check the lspci command and my wifi card is detected by the kernel because is an Atheros card, also I install madwifi-tools.
View 3 Replieswell traded my desktop for it and its a Dell Inspiron 1721. The Wireless was working fin when it had Windows vista on it but when I installed Ubuntu 9.10 The wireless just seemed to not exist. The LED wouldnt even turn on. So I installed wicd and then the wireless icon began working but it still won't find any wireless networks.
View 4 Replies View RelatedI'm running Debian Squeeze now, just did an upgrade yesterday. I had wl for my wireless and it was all working fine in Lenny. Now that I'm upgraded, wicd can't find anything at all.
[Code]....
I am trying to use nm-applet with Arch/Openbox/tint2. I can't use wicd-gtk because wicd won't work with ad-hoc networks. I have tested nm-applet in Ubuntu/Openbox/tint2 and it works fine.
The error message is:
Code:
[esteeven@piccolo ~]$ nm-applet
** Message: applet now removed from the notification area
[Code]...
I decided to try wireless so I bought a TP-Link pci adapter TL-WN851N and installed it. I installed Wcid and firmware-atheros. I set /etc/network/interfaces to read auto lo iface lo inet loopbackAll Wicd does is tell me "No wireless networks found."
View 14 Replies View RelatedI am getting "No wireless networks found" using Wicd manager. Below is some info that might help:
iwconfig
Code:
root@root:~# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
[Code].....
I somehow lost wicd. the icon is still at the bottom of the screen, but show "no networks present.' When I run iwfonfig as root it shows eth0 and lo, but no wlan0. When i run iwconfig, it says eth0 and lo with "no wireless extensions."
View 10 Replies View Relatedi'm using WICD as my wireless network manager. wicd 1.6.2.1 on slackware 13. I need to configure dynamic WEP with authentication, user name and password like shown on the pic. i couldnt find that option in wicd properties or configuration,
View 3 Replies View RelatedI installed Wicd in my F13 but I got problems when starting it When I try to start it I got error message:
Could not connect to wicd's D-Bus interface - Check the wicd log for error messages.
I'v just installed wicd. I can't get it to sart, I get errors saying that wicd couldn't connect to it's dbus interface and the wicd deamon has shut down. Then there's a report from SELinux saying that it's preventing /usr/bin/python "write" access on /etc/dhcp/manager-settings.conf and that access is denied to wicd. I can get wicd to start if I su to root, but I'd like to not have to do that every time I boot. Is there a fix?
View 1 Replies View RelatedI have a MSI A6000 laptop (the laptop that won't accept 10.10 because of the nvidia card) so finally I opted to get Ubuntu 9.10. I successfully installed with a dual boot.
There are two problems though that I have ran into.
1. Ubuntu 9.10 is not picking up wireless networks.
2. The Ubuntu graphics (icons, taskbar and windows) are much to large. I am guessing this has to do with the Nvidia card (nvidia GeForce 8200m G).
I have an HP Netbook that has Linux MintI have absolutely no issues with awired connection, however my internal wireless will not search and find wireless networ in range. It appears I have one saved (my home network) and I can connect to that, however, if I take my laptop to school or work, it will not find any networks to connect to. On a side note, I have no icon on the taskbar indicating wireless, and I used to have one. I have no idea where it went or what happened. I can answer most questions you may have but im a relatively new linux user (but I have a coworker that "knows all" and could help answer a question that I cannot.
View 2 Replies View RelatedI like to do a lot of my tasks through the command line, and was wondering, is there a way to see all the wireless networks available in the terminal? I tried 'iwlist scan', and it said all the interfaces do not support scanning. Is there anything I can do?
View 2 Replies View RelatedI am using 11.3 (64-bit gnome) and have a new Tenda w322p wireless n card, this works absolutely fine under windows, but I also bought it due to reviews saying it worked with linux. The card appears in network settings as RaLink WLAN controller and uses kernel module rt2800pci, I have also tried typing in the network ssid etc manually but it hangs on exiting network manager (will post what it says later, after writing this) I used drivers from here:Ralink corp., and used the rt3062 one(5th one down?)
for lspci
Code:
00:00.0 Host bridge: Intel Corporation 82X38/X48 Express DRAM Controller (rev 01)
00:01.0 PCI bridge: Intel Corporation 82X38/X48 Express Host-Primary PCI Express Bridge (rev 01)
00:06.0 PCI bridge: Intel Corporation 82X38/X48 Express Host-Secondary PCI Express Bridge (rev 01)
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02)
00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02)
[Code]....
I have also had the same problem of not picking up networks in Ubuntu, not sure if the drivers are 64-bit compatible or something.
I went out and purchased a Sabrent PCI wireless 802.11n card with the RT2860 chipset because it was on the ubunutu compatibility list and has linux driver available from the manufacturer. I was impressed that the card worked in wireless G mode out of the box, which is a great start....
However, I can't find any wireless N networks. Dual booting I can find/use my N network, but in ubuntu I can only find my G network. This is somewhat frustrating because I bought this card and a new (read: expensive) Linksys E3000 router specifically to run a nice new N network...
I have downloaded, made, and installed (reboot) the latest driver from the manufacturer, but it still won't find any N networks. I found a few posts by searching here and google that alluded to changing this line: "HT_OpMode=1" (from 0 to 1) in the config file RT2860STA.dat located in /etc/Wireless/RT2860STA/ and a reboot. It didn't work for me.
Frankly all this rebooting is starting to **** me off ... I have spent most of last night trying to setup my 180$ wireless network and its still no better than the freebie DDWRT54g based wifi it replaced. I am frustrated, perhaps someone wiser in the ways of ubuntu and wireless N can shed some light on the situation....
I forgot to mention I am on Karmic Kola, amd64 with the standard gnome.
i installed network driver using ndiswrapper so the network driver is all installed
packages for ndiswrapper:
ndiswrapper-common version: 1.9
ndiswrapper-utils version: 1.9
ndisgtk version: .8.5
[code]....
then i did
command: sudo ifconfig wlan0 up
contents: SIOCSIFFLAGS: No such file or directory
[code]....
i'm running ubuntu 10.04. i've followed these instructions:[URL]that got the light for the wireless on my laptop to light up but it doesn't seem to be able to find any networks.when i click on "connect to hidden wireless network" and enter the details + encryption code. it spends a few minutes trying to connect before asking for my encryption code again but i know that the code i entered is right.i'm using a belkin router with wpa/wpa2 encryption. but i think it's a problem with the wireless on my laptop rather than a problem with my specific network because under windows on other machines in my house i can see some of my Neighbours networks
View 2 Replies View RelatedI am not able to find the most Wireles icon, I want to connect to other networks, so there will not I print a summarizing what is happening.
View 3 Replies View RelatedI have Lucent Technologies Orinoco Silver 11 Mbps PCMCIA wifi card. It worked perfectly in Fedora 10, but after updating to Fedora 11 it stopped finding any wireless networks. The updating were done with automatic updating utility. The card works perfectly in Windows, I tested it today.
My laptop is HP nx6110 if that matters.
Here is the situation:
When I plug-out the card, the Network Manager disables wireless networking as it should. When I plug-in the card, wireless networking is enabled, so the system seems to recognize the card in some way.
If I try to connect to "Hidden wireless network" (because there isn't any wireless networks listed in the Network Manager) system tries to connect for a couple of minutes, and then asks wireless settings again. Orinoco card's lights DOESN'T blink normally when connecting to the network (one light should blink rapidly and one should light continuously, but both are blinking rarely or doesn't blink at all).
In System->Administration->Network in tab Hardware (hope those names are correct, I use Finnish version of Fedora...) is:
It seems that the card is detected right.
Here is what I have done to get the problem solved: In System->Administration->Network I have tried to connect to the wireless network manually (disabling the Network Manager). I can't get the connection. It gives me random error messages, sometimes "Check the cable" or something like that, sometimes just timeouts IP determination.
I have tried to connect different wireless networks, no connection. All tested networks worked with another computer.
No matter if I reboot or service network restart or plug-out plug-in the card... the problem still appears.
Tried to find (and reinstall) drivers:
Code:
No Matches found
Code:
Here is the output of lspci. The output is the same if the wifi card is connected or not.
Code:
LAN connection is working just fine.
I am trying to configure my android phone (rooted Eris running kaossfroyo 2.2) to be used as a midi controller. Which I am having enough trouble with as it is but it has raised an annoying issue that occurred a month ago when I used the phones tethering network with my laptop. After connecting the laptop to the phones network (either tether, or an Ad-hoc network created using the network manager) I am unable to switch to other networks. In other words when I'm done with the phone-laptop connection I cannot connect my laptop to my home network! When I click on the other network connection I can see that it is attempting to connect in the upper right corner of the desktop (the network icon) but it will not make the connection.
What happens is that the network indicator will make the little circle graphic as if it is trying to connect but it never will display the other circle as green indicating that it has connected. but when I disconnect from the home network that is not connecting I will get a message underneath that will say that ad-hoc network disconnected! If I am switching from the android tether it will say Android-Tether disconnected etc. Even though when I click on network manager it shows that I am attempting to connect to the home network (labeled LIBERTY in my case) upon disconnection it shows the ad-hoc or tether connection being disconnected.
I am absolutely baffled by this! The issue persists even after deleting the ad-hoc connection from the wireless settings tab!!! I would speculate that for some reason the laptop is attempting to connect to the previous ad-hoc connection despite me wanting it to connect to LIBERTY. I am very confused and hope someone can lead me in the right direction.
For some reason, ubuntu cannot find local wireless networks. In fact, the Broadcom wireless card Ralink RT5390 802.11b/g/n seems to be incompatible with ubuntu. I've tried numerous 'solutions' on the Internet, but none of them seem to work on my computer. Tutorials I've visited have recommended downloading the b43 drivers from the Synaptic package manager and also the bcmwl-kernal-source package. Nevertheless, the wireless never turns on and Additional Drivers never shows anything at all. After several exasperating hours of trying to get my wireless running I've decided to turn to the forum for help. I'm sure there's probably more information I should supply, but I'm honestly not sure what that would be.
View 2 Replies View RelatedI could use Wireless network. I could see several different networks in my range. Then suddenly the network stoppedworking, and I can no longer see any networks under "Wireless networks".The Wired networks works fine.I tried upgrading ubuntu, but nothing changed. Just to confirm, I rebooted the computer in Windows Vista (Dual boot) andconfirmed that Wireless worked fine there. No hardware problem then.The suggestions I have found on this and other forums suggest looking at the output from iwconfig and ifconfig. But since I'm a n00b at Ubuntu I don't know what to make of it.
This is the output:
emil@emils:~$ iwconfig
lo no wireless extensions.
[code]...
I don't know much about networking... I have Debian Lenny and use wicd to connect to my wireless. Yesterday, I changed my ISP and now I cannot connect to the wireless signal, only to the wired. It had happened before that it took some tries to connect to a new network, but, after a few tries, it would connect. And then it would always connect at once. But now, it always gets stucked on the obtainment of the ip address. The same routher gives me a perfect wired connection... My wife has Ubuntu and she got it working right away, so it's not a password or router problem...
View 11 Replies View Relatedmy problem: i am using unbuntu 9.10 on a dell 1420 inspiron laptop. i wanted to uprage to the new version of linux "lynx" . while i was doing that a problem occurred while downloading the new packages. It said that what i have already downloaded would be saved but i had to restart the download--so far no real problem. When i restarted my computer, wicd wanted to access my internet card interface, or something like that, and asked for my password, i gave it, and then wicd said it couldnt connect to my internet card and i needed to check the wicd error log. everytime i restart my computer i go through the same process and always end up with NO INTERNET CONNECTION WHATSOEVER, not just wireless, wired connections dont work.
i hope that was clear. the reason i was upgrading to lynx was because wicd had problems in the first place, but now i cant get on the net in any way with my laptop--so how do i fix the problem? should i burn an iso of the new linux and then stick that on my machine to uprgade? or is there another way. The main goal of mine is to have a laptop with linux that can wirelessly access the internet.
If i didnt provide enough info, i'm sorry(i'm young, but computers are pretty baffling sometimes) or if you want me to do something i can post the results, but i dont know any codes and can't find the error log for wicd.
on my laptops I used to use Wicd with the Gtk GUI. However, now there is a KDE client, which I want to use instead, from now on:
Wicd Client KDE
I installed it, and it works quite well, so far. However, whenever I logon to a KDE session, the older Gtk client is started, too. I then have both Wicd clients sitting next to each other on my panel bar, and I have to manually kill the Gtk client. How do I get rid of the Gtk client in KDE, permanently? BTW, my laptops are running Slackware 13.1 stable with all patches up to now and some additional software from various repositories.
I tried to install wicd so I can connect to my wireless internet, but it gives me the following output:
/usr/share/wicd/gtk/gui.py:458: Warning: Source ID 54 was not found when attempting to remove it
gobject.source_remove(self.update_cb)
ERROR:dbus.connection:Exception in handler for D-Bus signal:
Traceback (most recent call last):
File "/usr/lib/python2.7/dist-packages/dbus/connection.py", line 230, in maybe_handle_message
self._handler(*args, **kwargs)
File "/usr/share/wicd/gtk/gui.py", line 253, in handle_connection_results
error(self.window, language[results], block=False)
KeyError: dbus.String(u'bad_pass')
I have checked that the pasword is correct. I had network-manager installed but it has been uninstalled. I am trying to connect to a WPA2PSK router. I might be a firmware problem, since I get a 'message' on the start screen that there are some problems with my firmware, but I can't figure out how to check if it is broken, or how to configure it so it is correct.
I have the qualcomm atheros ar9485 wireless card. As far as I can tell, the driver for that is either ath3k or ath9k, both are installed. The message I get when I start the computer is: usb 1-1.1: firmware: failed to load ar3k/AthrBT_0x01020200.dfu (-2).
I would like to backup my wicd profiles. I thought it would be sufficent to copy /opt/wicd/data and /opt/wicd/encryption - however, those path do not exist in lenny (which I am running). So which path / folders / files do I need to backup in order to back up the wicd profiles and configuration?
View 1 Replies View RelatedI recently purchased a laptop from zareason. Seems great, only I've been struggling with getting the wireless to work. I feel like I'm awfully close.
Note: I'm running Lenny.
I downloaded what I thought was the driver for the card. The card info is:
Intel
Model 533AN_MMW
Intel WiFi Link 5300
MAC 00216A72EE22
TA: E50434804
I've successfully install wicd, but it doesn't detect any wireless network. Other computers seem to register the wireless network in my apartment.
I recently installed wicd on a notebook with Squeeze. I can connect to the wireless network at my place. However I cannot connect at my friend's place. It timed out with the message: "Connection failed. Cannot obtain ip address."
It is a Thomson router/modem and the key is a 10 digit 64bit Hex. I did not see 64bit Hex option in wicd. So, I tried all 3 WEP options and none of them worked. We can connect to the same network with another computer with Squeeze and NM and also with Windows. This is the first time I am using wicd.
how to install wicd on F11 or a link to an rpm? All the guides available dont seem to work on F11.
View 11 Replies View Related