I have enabled USB -OTG as Both Host and peripheral. USB - OTG host mode is working fine but USB - Device mode is not working...I'm unable to load g_file_storage.ko,I get below error:
View 2 RepliesI installed Centos 5.4 on my Pentium E5300 new comp, but I need IPX support in my work. It's simple - ipxutils and ncpfs from Fedora Core and new kernel with ipx support. I copied kernel config from /boot folder and activate ipx, ntfs support, and choose processor core 2 duo. New kernel (2.6.26) works OK, but I got one problem - when start it still shows message: "kernel: HUB 1.0:1.0 unable to enumerate USB device on port 1 (or 2, 3)" and stops after logging (text mode)
I got 2 USB devices connected - printer HP D5160 PhotoSmart and Scanner A3 USB Mustek, and I know scanner cause that messages but I don't understand why. Kernel config is the same like that from distro kernel (almost - ipx, ntfs and proc), but distro kernel doesn't do that. So I got 2 questions:
1. Why
2. What to do to stop that (disconnecting devices on boot time is not a solution)
I've looked today on my logs /var/log/message and I find device eth0 entered promiscuous mode I don't remember putting eth0 in promiscuous mode I'm connected to the net thru a router how do i turn that off ?
View 1 Replies View RelatedAll my music editing software programs say, "unable to open device /dev/dsp.Device or resource busy." How can I fix this?
View 3 Replies View RelatedEnvironment: A 32-bit kernel RHEL5.3 system running on a virtual machine. The root(/) filesystem is on an LV.
Issue: Unable to resize the FS after extending the root LV since it is mounted. After extending the LV, online resizing of the FS was not supported and the root filesystem could not be unmounted while it was in use. On rebooting, I got a kernel panic error. In runlevel 1, I couldn't run chroot, couldn't find the /etc/fstab, root FS could not be mounted, fsck did not run (tried block 31 for second copy of superblock using dd count=1 bs=4k skip=31 seek=1 if=/dev/sda2 of=/dev/sda2), couldn't find any rpm on installation media to install unix-utils rpm. On running commands in runlevel 1,
I got the following output.
How I do detect the usb device when I'm on cli mode? This is possible or not?
View 2 Replies View RelatedI made a backup of xorg.conf and added Xinerama and the other configuration items I needed. X failed to load. Then I copied my backup to xorg.conf and...X failed to load. Then I tried booting up in safe graphics made, and X failed to load. I tried dpkg-reconfigure xserver-xorg, but it did nothing. Literally nothing -- no error, no output, no nothing. Then I saw someone who had suggested to apt-get remove --purge xserver-xorg, then reinstall it, and X failed to load.
I am at a complete loss. I have now read that the dpkg-reconfigure xserver-xorg is no longer used, that the os is supposed to autodetect everything now, but in that case I don't see how I will ever get dual monitors. In any case, I can live without dual monitors, but I need at least ONE monitor, and I have no idea how to get the configuration working.
I am writing a device driver on x86 machine,Ubuntu distribution,kernel version 2.6.35.I want to debug my driver in kernel mode.I tried KGDB(Kernel Level Source Debugger).But support is given for kernel version 2.6.13.But I want to make KGDB work on version 2.6.35.Could anyone help me where can I get help to make KGDB work on 2.6.35 version?Or is there any other method to debug my driver using some other tool?
View 1 Replies View RelatedI just compiled my first own kernel (I'm using Arch Linux), following the tutorial on the german site. Now I tried to boot it, I ended up failing with this message: Code: Waiting 10 seconds for device /dev/sda1 ... Root device '/dev/sda1' doesn't exist, Attempting to create it. ERROR: Unable to determine major/minor number of root device '/dev/sda1' Here is the important part of my menu.lst:
[Code]....
I simply copy&pasted the Arch-entry, i.e. I also had the disk by uuid there. The failure message was the same, just the root device name was the different name Also, at first I did not have the initrd line in my menu.lst (as written in my tutorial that I may not need it). In this case I had this error message:
[Code]....
I can run Ubuntu 10.04 just fine as long as I have my hardware drivers disabled, but when I enable my hardware drivers I get an error before the GDM login screen that says something to the effect of it being unable to load the NVIDIA KernelI'm then given the choice of booting into low-graphics mode, configuring xorg for this hardware, troubleshooting, dropping to console, or restarting X.Booting to low-graphics mode does nothing useful, just boots to low gfx mode.Configuring xorg for this hardware does nothing at all - same errors after trying every single option in the configuring xorg sectionTroubleshooting is equally useless to me - I can't copy and paste the very-long error reports, I'm not an xorg pro so editing the xorg conf doesn't help me, and when I tried following the option to export all my config and error logs, it said that it has exported it to $xorg_backup_file - but that's just a variable not a file.. after a reboot I can't find this anywhere.
I've googled this and the only useful info I've found is to run nvidia-xconfig as root, which I've done and it has zero effect.The only temporary solution is to disable the nvidia driver, which lets me boot normally using metacity at full resolution, but has no accelerated 3d or composite overlay so I'm unable to run compiz or have any nifty 3d.Details: Vid card: NVIDIA G96 (according to lspci) Driver: NVIDIA accelerated graphics driver (version current) [Recommended] OS: Ubuntu 10.04
I have two hard disks sda and sdb. I have Windows XP installed on sda2 and Ubuntu 10.04 on sdb5. When I installed Windows XP, Ubuntu stopped booting. I tried to repair grub2 from a Live CD unsuccessfully. Now I have completely messed up my MBR of both HDDs. I just want to configure grub2 to load both OSes in dual boot mode.
View 9 Replies View RelatedI am totally new to Linux and have a PC here with 128 MB Ram and a 10 GB HDD. It has Windows Millenium installed but I presume this will be wiped during the install process if I so wish.,
I am part way through the install using CD's and have just chosen my required alnguage and then keyboard layout. The next option is asking me to choose what device drivers to load and most appear to be HDD Drivers. I haven't a clue what to choose here?
I just got finished installing Ubuntu on 2 computers. I muddled my way thro the panels not installing. Now I would like to hook up a dual mode camera. Vivatar V15 . I know very little about Linux, but as having fought with Microsoft Windows for years I find it refreshing to see Ubuntu. I need to know about device drivers. Ubuntu does not auto detect the camera. The Model of the Camera isV15 Freelance.
View 1 Replies View RelatedI am installing fedora 15 in vmware 7.1.4.It tells me "Gnome3 failed to load and started in the fall back mode" when accessed in live-cd.Ever since fedora 15 beta or any other distros take gnome3 as default destop,I haven't experienced a beautiful normal gnome3
View 14 Replies View RelatedI downloaded the full install of Fedora 10. I burned the DVD and it booted okay. Going through the startup stuff, select language, keyboard, ect and then I choose the dvd as the source of the image. Then I get "no driver found" and gives me the option to choose from a list of drivers or to use a driver disk. I saw something in the forums about someone having the same problem but theirs was a video card issue. On the list of drivers it looks like they are network card drivers. I have no idea what to do. I am using a NVIDIA Geforce FX 5500 if that helps. I also did not verify the iso, though wouldn't it not boot at all if the iso image was broken?
View 7 Replies View RelatedI just did a clean install of 11.04. Now when I try to boot the machine I get the following error: Quote:
error: no such device
error: no such disk
error: you need to load the kernel first
Then I am taken to the Grub menu. Selecting anything from the Grub menu brings this error back up. So now I'm stuck with a computer that won't work.?
I've running ubuntu 11.04 on my samsung 900x3A notebook and have a problem using the touchpad: I've configured my touchpad using "GPointing device settings", but everytime I reboot my system I've to start "GPointing device settings" manually to apply the settings for the current session. Is there a way to do this automatically?
Secondly I've the following problem: I cannot use "click and move" with my touchpad. For example, when I try to move a window around: Normally one would click the left button, hold it and move the window via touchpad. But every time I click the left button, any other movement with my touchpad is disabled. Is there a way around this?
When I try to install CentOS 5.3 and when this dialog. Select device Driver to load. I try to install it on ASUS Server.
View 8 Replies View Relatedsince ever, i face the problem, that i cannot continue using my computer properly after i suspended it to ram and wake it up again.Fedora 14, 64-bit, most recent and stable kernel
mainly KDEMotherboard: Gigabyte P55A-UD4Hard DrivesSAMSUNG HD501LJSAMSUNG SP1213NI can figure out, that everything works fine, but with a severe delay.Having a look at my led, signifying hard drive activity, it flases once a second for approx 10ms. frequency is very constant.so i performed several checks:firstly, hdparm -i, there is no difference before and after sleeping mode:
Code:
[root@bobbl-pc bobbl]# hdparm -i /dev/sda
/dev/sda:
[code]...
I'm unable to login to my Kubuntu Lucid. The login screen takes my password, blanks, then returns me to the login screen. I'm getting some graphics errors when running from recovery mode as well as the no space left on device error when attempting to start x from the terminal. Here are some outputs: When starting from recovery mode, selecting failsafeX from the Recovery Menu:
[Code]...
I've come to the conclusion that my root partition is full, but I'm not sure how to clear space, or how much to clear once I work out how to do it. I removed a few packages with apt, but it doesn't seem to have any effect. df -h shows that root is 100% full, yet it has 3GB free. I've grown comfortable with Ubuntu in the couple years I've been using it, yet this level of problem-solving is a bit nerve-wracking to me. I've been considering reinstalling (this machine is running Lucid upgraded from Karmic and Jaunty and has a few oddities), but I hate the idea of being forced to reinstall because I can't overcome this problem. If you need any other information or outputs from terminal commands, I'm happy to provide it.
Is there a way to switch a internal card slot from /dev/mmcblk0** to /dev/sd** ? I'm backing up (via rsync) an ebook directory (1.9gb) to sd card and get massive i/o errors, card turning read-only,etc. This is via a built-in slot on a toshiba laptop. When I use a card reader, the card attaches to /dev/sdd1 and all is fine.
This is a new Sid install. The laptop's card slot worked fine under Ubuntu 9.04 and still works if the amounts of data are small. All I can figure is that the mmcblk device dies under a heavy load...
64bit Slack doesn't recognize my ethernet device. ifconfig -a show no eth0. It's an onboard nvidia MCP55 ethernet nic. Never had this problem using 32 bit Slack.
When I try to modprobe forcedeth I get the following error:
repeats those two statements 3 times
I just recompiled my kernel with every possible 10/100 ethernet device included in the modules. Still no go.
Below is a print out of my partition Table from Fdisk, in Cylinder mode, Sector mode, and then in expert mode?
Why in expert mode does it look like Partitions 2 and 3 share the same sector / hd / Cylinders? Is this OK?
Code:
I have a brand new Z97-PRO (Wifi/USB3.1 version) that I got to replace a Gryphon Z87, and it was working great for the first day. I had my Debian and Windows drives both working, and I was working on getting GRUB reinstalled on the Debian drive in no time. At some point I needed to restore my Windows MBR for the millionth time, but this time was different. The Windows logo popped up and froze there. I know this is a thing that sometimes happens, but every other time since I replaced my Gryphon this process only lasted seconds. I let it sit for hours and it didn't move.
I then tried my Debian live USB, which loaded into the main menu, but upon selecting rescue mode it black screened and hung. This was an issue I experienced when I first got the board, but it seemed to work itself out after a few reboots and remained flawless until it just came back. At this point, I'm unable to get in to any of my OSes and I can't seem to successfully boot any external media in order to fix it. My BIOS is totally stock save for secure boot, which is set to Other OS, and memory in XMP mode. I also tried using an Ubuntu Live USB, but ended up hanging with the exact same Q-Codes as in Debian. I am running the system on 1 stick of RAM while testing.
Q-Codes at hang:
UEFI USB - AF (Exit Boot Services Event)
Regular USB - F6 (Reserved for future AMI progress codes)
Specs:
- 2 boot SSDs (OCZ for Windows, Kingston for Debian), 2 storage drives, and a DVD drive.
- The boot SSDs occupy SATA ports 1 & 2, the DVD drive takes up 3, and the storage drives take up 5 & 6
- i7 4770K, 32GB (8GBx4) Corsair Dominator RAM, GTX780Ti
- 750W Silverstone PSU
I'm trying to boot into emergency mode but i'm having no joy. I can boot to single user mode (by adding s or single at the end of the kernel line in grub) and I can also boot to init=/bin/sh mode by using the same method, but emergency is not working. I'm using RHEL6 x64
View 8 Replies View Relatedjust built a computer and wanted to try out some linux.
First off I burned the Fedora 10 x86_64 disk image (using disk utility on my mac at 4x speed then verified it) to a dvd. I start the install. "x startup fails to load, falling back to text mode" comes up. I use the text install then. It gets to the actual installation of the different packages then a black screen shows up with white text that's highlighted red (sometimes it's blue). It then freezes and I reboot. Sometimes it freezes at different points and with different messages, but the description above is what happens most often.
I try writing it at 1x speed and verifying. same thing.I try the Live CD. It freezes.Then I tried Fedora 9. same thing.
Next I go to Ubuntu 8.10.I try the regular install, but the orange loading bar freezes.I try the Live CD-like install. It runs!...but when i go to install, when it gets to the partitioning part, it freezes and becomes unresponsive.
Each time it froze I let it sit for about 10 minutes, just to make sure it is in fact frozen. I've tried these installs numerous times.
I updated yesterday and now when I start my laptop it goes in to grub rescue mode. I have booted from a 'live cd' and thought I could repair grub from there. In gparted however the partition with ubuntu (sda1) is seen as unknown file system, in terminal when I list the partition table it shows up as FAT16 type. When I try a grub-install it gives this error message:
[Code]....
I want to automoate some PPT -> PDF conversions, so I want to run openoffice in headless mode for scripting.
On my machine with X running I can start opemoffice in headless mode via
soffice -accept="socket,port=8100;urp;" -headless
This doesn't seem to work on a server with X not running.
$ soffice -accept="socket,port=8100;urp;" -headless
/usr/lib/openoffice/program/soffice.bin X11 error: Can't open display:
Set DISPLAY environment variable, use -display option
or check permissions of your X-Server
(See "man X" resp. "man xhost" for details)
$
The error doesnt seem to make sense as well, as the point of specifying -headless was so that I do not need X, while this command seems to look for X.
I was using win-7. I tried to install RHEL 6 today. [dual boot]/ = 40000 MB and /boot = 1000 MBThe installation completed successfully.The problem is that it is not showing the graphical mode. Only the terminal mode is available. I tried chvt 1-7but I am unable to go to the graphical mode. It is not appearing.What should I do? System config:MSI CR420 Laptop.ntel core i3-350MEdited after following user76871's answer:There is no Xorg.0.log file in /var/log/, There is no xdm in /etc/init.d/, there is no kdm also.I tried startx that also didn't work. I tried system-config-display but the display is not available at system-config-
View 2 Replies View RelatedI installed lucid last week, and this morning installed some updates that appeared in update manager and then started having issues with permissions so I rebooted. Now when I try and log in I get the message Authentication Error Normally this wouldn't be a problem I would reboot again hit ESC just before loading Grub appeared and go into recovery mode and change the password for my master user. But I never get the chance to press ESC, and even I hold the key down from the time my BIOS flash screen is up, I never get the GRUB menu.
View 1 Replies View Related