Software :: Boot Failure - Failed Command: READ FPDMA QUEUED" Error At Startup
Apr 22, 2011
I have a netbook with a 150GB hard drive in it. A while ago I dropped my netbook and it wouldn't boot. Had a "failed command: READ FPDMA QUEUED" error at startup. So naturally I went and reinstalled. Reinstalling worked fine and I had my computer back. What I didn't account for was the fact that anytime it lost power and didn't shut down properly, I'd get the same error. I can't seem to recover my data either. Can't get any live disks to mount the hard drive after this error but for some reason I can still reinstall Crunchbang (essentially debian). Now I know there are bad sectors or something because when I try to use the disk that came with the netbook with an image of Windows XP that writes to the entire hard drive it throws an error but linux will avoid this I suppose when installing.
Now all of this is to say, being a laptop, several times I have left it on overnight when I fall asleep working or have to run into to town and it'll die and then I lose all my data, rather irritating. What's causing this error? What can I do to prevent it besides getting a new hard drive? If I can't prevent it from happening in the future is there a way to recover the data off the hard drive? Here's the section of the boot log that contains the error: [url]
View 4 Replies
ADVERTISEMENT
Mar 7, 2010
I tried to compile a 2.6.33 kernel following Alien's guide.
I pretty much used the default values for every (NEW) option avaiable. I used "make localmodconfig" on my current config (zcat /proc/config.gz) and then tried to use "make menuconfig" to check if I could change anything. I didn't understand most of the options, so I skipped it. Then I used "make bzImage modules" and "make modules_install", copied the files mentioned on the wiki and run lilo.
But when I try to boot using my custom kernel, it gives an error like "Cannot remount read-only filesystem as read-write! This can cause serious problems."
If I try to continue the boot, it hangs when trying to launch the syslog script...
The new kernel entry on lilo.conf is:
Code:
image = /boot/vmlinuz-custom-2.6.33
root = /dev/sda4
label = newkernel
read-only
just like the default kernel entry.
By the way, one thing I changed is the kernel compression format, which I set LZMA. But it didn't seem to be the problem, since it at least started...
View 10 Replies
View Related
Apr 18, 2011
I'm not very sure when this issue started. Anyway, the system finally boots and I haven't had any further problems, but I somehow notice the booting to be a bit slower since this error appeared and I don't like watching the red letters that say "failed" every time I switch the computer on. I googled this before posting it, and other users have had this issue, but the solutions that worked for them didn't work for me.
This is the content of my /etc/network/interfaces file:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
View 5 Replies
View Related
Mar 4, 2010
I realize this probably isn't the best place to be posting this as it relates to project open, but they don't have a forum.
We recently upgraded our Ubuntu server and now when trying to use project open we get the follow error message, does anyone know why this may be, or have any guesses as to why this may be.
Server startup failed: Error during bootstrapping
No fullquery for dbqd.acs-tcl.tcl.apm-procs.apm_package_installed_p_not_cached.apm_packa ge_installed_p and default SQL empty - query for statement missig while executing
"error "No fullquery for $statement_name and default SQL empty - query for statement missing""
(procedure "db_qd_replace_sql" line 10)
code....
View 7 Replies
View Related
May 1, 2010
I upgraded my Karmic OS to Lucid the day after it became available and have been having some troubles - I am having trouble starting the OS. Brief history: I have real troubles with the ATI graphics and spent a while trying (finally successfully) to remove fglrx and associated dependencies. I then rebooted ready to install new drivers. I now get the following error on startup:
CIFS VFS Error connecting to socket - aborting connection
CIFS VFS cifs_mount failed w/return code (-101)
For the last couple of weeks or so, I have noticed CFS errors on shutdown which has meant that I have needed to physically press the off button to turn the machine off, but since I could still operate I left that problem on the back burner "for when I have more time". Don't know if the two problems are related. Anyway, I am currently in the situation where I cannot start Ubuntu at all unless I use the install CD and try the LIVE distro.
My fstab file looks like this:
aufs / aufs rw 0 0
tmpfs /tmp tmpfs nosuid,nodev 0 0
/dev/sda6 swap swap defaults 0 0
(My PC Has a 1 TB drive and a 500 gig drive. The 1 TB drive has dual boot Vista (came preinstalled and I have a couple of games for it - else, yuk) and Linux. The 500 gig drive is a data drive). I'd rather not reinstall from scratch though may have to? I don't know of any way to repair-install the OS - maybe that would be possible too?
View 9 Replies
View Related
Dec 16, 2010
I am running into a strange problem where kickstart installation fails with Error failed to read Rpm header, This happens when installation starts formatting of disk is also completed some of the rpms installed and then suddenly installer stalls with failed to read rpm header.
I have kept kickstart and install media on same host. I have changed the install media from http/nfs/ftp just to check is there any problem with the media but no luck.
However same installation with the same kickstart file works fine when both install media and ks file is kept on another linux host.
I am using RHEL 4 ,I do checked /var/log/messages it does not give any information on the failure and this started happening recently till that i was using the same server for my linux deployment.
Note: pxe setup, boot server ,install media and ks file all are in same server.
View 2 Replies
View Related
Mar 3, 2011
I am unable to rip from CD to .mp3 using pretty much any tool. Dolphin / Konqueror auidiocd:// KIO slave shows the mp3 folder, but when you move the tracks you get: Could not read some_song.mp3: encoding failed WARNING: libsndfile may ignore -r and perform fseek's on the input. Compile without libsndfile if this is a problem. I'm running 11.3 (KDE 4.4.4) with K3B 2 from Packman (with the k3b 2 codec package) and K3B fails as does the KIO slave method above. Lame version is: lame-3.98.4-2.pm.4.1.x86_64 Restricted multimedia formats packages are installed from Restricted formats/11.3 - openSUSE Community Wiki Alsa works great otherwise, I have no sound issue, etc. - just can't rip anything to mp3 Seems like I'm not the only one who has had this problem, there are a few posts here on the Suse Forum, and others elsewhere, but the resolution seems to be nebulous at best. Sometimes lame 3.98 from packman works for some guys, other times not, etc. Unable to rip an audio cd into mp3's using 11.2 - opensuse.opensuse.org - ArchiveOrange
View 9 Replies
View Related
Apr 22, 2010
[code]...
Failed to read mirror file. it eventually shuts down saying "reverting to original state"?
View 1 Replies
View Related
Dec 8, 2010
figure out this error?
Code:
kradalby@hpcompaq6530b-laptop ~/.ssh $ ssh -vvv -p 110 kradalby@dfekt.no
OpenSSH_5.5p1 Debian-5+b1, OpenSSL 0.9.8o 01 Jun 2010
[code]....
View 3 Replies
View Related
Sep 7, 2010
I'm trying to mount my new Western Digital Elements 2tb hard drive, but every time I try to plug it into the computer I get this error message:
Quote:
Error mounting: mount exited with exit code 12: Failed to read last sector (3907027119): Invalid argument
HINTS: Either the volume is a RAID/LDM but it wasn't setup yet, or it was not setup correctly (e.g. by not using mdadm --build ...), or a wrong device is tried to be mounted, or the partition table is corrupt (partition is smaller than NTFS),
[code].....
But when I tried opening the hard drive from nautilus I still got the same error message as above (no other volumes was connected at the time). I've also tried opening and watching it in GParted, and I can see it there as a volume that's not allocated. When I tried to allocate the hard it I got the message that it had no partition table. And that I cold make one. I tried and Ubuntu suggested to make a MS-DOS partition table for it. But there I got a little scared as I've not done this before. The external hard drive is brand new and was brought today. And I don't have the possibility to test it with Windows or Mac as I'm using Linux only on my machines.
View 6 Replies
View Related
May 1, 2010
simple scan error as follows: Failed to save file ImageMagick returned error code 11 Command line: convert -adjoin /tmp/simple-scan-DA9MBV.jpg /tmp/simple-scan-XCK4BV.jpg /tmp/simple-scan-NZVYBV.pdf Stdout: Stderr: using karmic note: I have apparmor extra profiles installed but didn't notice one that related to simple scan or imagemagick. Red herring or not?
View 6 Replies
View Related
Mar 25, 2016
I'm getting BSOD when I'm booting my main system (debian 8 fully updated). I get a BSOD with a _ sign. URL...because I can't access to failed boots files. Besides having the files
Code: Select allfelipe@debian ~ % ls /var/log/journal
362d07f9e18b45f8aec4575c347f181d 92e8a448f7a348719da129184a7e6821
Code: Select allfelipe@debian ~ % journalctl --list-boots
0 0c51ae5b67f144059c5470dbe345d621 vie 2016-03-25 09:05:29 ART—vie 2016-03-25 09:11:58 ART
View 3 Replies
View Related
Dec 2, 2010
I changed my motherboard battery last night, and now get "Read Error" on booting to Ubuntu, on dual boot system. This is the most frustrating thing in an otherwise great operating system. It is the second time I have encountered this issue (last time was a change of power supply). I fixed it last time after three days of re-loading Grub2 and playing around Grub 2 updates, etc. Fixed it eventually, but as usual, no idea of what eventuality fixed it. I think I found a web page buried deep in the 'net, which talked about device.map. Do you think I can find it again - not yet - day 2 searching for the answer... This is what the grub script tells us:
[Code]....
View 7 Replies
View Related
May 3, 2011
I'm running Fedora x86_64. I need to setup a virtual machine to do some work on ARM platform. Thus, I've installed QEMU.
Code:
qemu --version
QEMU emulator version 0.13.0 (qemu-kvm-0.13.0), Copyright (c) 2003-2008 Fabrice Bellard
Then, I have dowloaded an ISO image of Debian 6.0 armel.Following instructions on official wiki, I have first created an empty disk image,
Code:
qemu-img create -f qcow debian-armel.img 650M
then I have attempted to boot from ISO image;
Code:
qemu -m 512 -hda debian-armel.img -cdrom debian-6.0.1a-armel-CD-1.iso -boot d
Boot process hangs with the message:
Code:
Booting from cdrom...
639 medium detected
Boot failed: Could not read from CDROM (code 0004)
No bootable device
link refers to Fedora 12, but it seems still unresolved...
View 4 Replies
View Related
Jun 26, 2010
I had occasion to add a few lines to rc.sysinit. Turns out the lines syntax was wrong. Instead of the booting ignoring those lines and proceeding on, then giving me an error warning or perhaps dumping into the interactive mode it just hung up! After several tries at moving on I discovered ESC dropped me into some sort of unannounced shell I got the installation disk out and with the repair system option using VI I got the lines deleted and all went back to normal. Now my suggestion is that if something does not make sense in terms of syntax while booting then cover it by doing the above and ignoring it with a warning later.
View 14 Replies
View Related
Jul 27, 2010
I installed from a live disc months ago. It worked fine for a while, don't remember what caused the change.
Now when I boot, I get this message:
Quote:
I have several hdds in this desktop box, one other has a OS on it, has the Hardy version. But i disconnected that (it all used to work with both drives connected and I was able to use that boot menu to change from one OS to the other). I can boot by getting to "boot menu" by pushing the "esc" key when the bios starts (just after the beep). It gives the option to start from, with a list of possible devices to choose from. I don't know where this menu is from, bios or other. I select hard drive, then select the correct hard drive and it starts right up. That is nonsense though. I really no longer need version 8.04 but keep it as a backup in case my preferred OS/hdd fails.
View 3 Replies
View Related
May 10, 2010
I have just installed Ubuntu 10.04LTS however when I attempt to boot the HDD I get the following error message
Read Error
Thats it nothing else, I am able to boot a USB installed version of Ubuntu 10.04LTS no proble. I can boot a Live CD of the same version no problem but when I installed it to the hard drive it just seems to fall over. I've tried adjusting the boot order, putting the HDD first and removing everything else but no joy. Im a linux n00b so no idea what to do next apart from go back to windows.
View 9 Replies
View Related
Aug 11, 2011
I have a fresh computer with specs as such:
Hard Drive: Western Digital Caviar Black 500Gb 6Gbs Sata
Asus Sata DVD/CD Burner
Core i3 3.3GHz Sandy Bridge chipset
MSI P67A-GD55 Motherboard
Zotac GTS 450
I have a problem where the live cd gives this error message:
Boot failure, sleeping forever.
View 12 Replies
View Related
Feb 27, 2010
I just bought a brand new hardrive (40gb western digital) IDE, 10 pin.I have gone through the installation and partioned the hardrive, when it gets to 100% it asks me to reboot.So i take the disk out, and then it says DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER:So i press enter and i get the same message> How can i get Ubuntu to boot up?The computer is a 2003 Medion pc with 512mb of RAM And an AMD Athlon processor. The computer has a sticker on that says: Designed for windows xp.
View 9 Replies
View Related
Jan 19, 2011
I am running the latest suse release downloaded directly from their website. I ran the installation after buring the dvd and everything seemed to be working fine. after the installation i ran updates and used it for a little bit. When i shut it down that night and went to restart it I got an error that stated the OS wasnt there. I then went through the installation and everything and it retained the information from the installation before (web history etc.) but for some reason every time I reboot or shut it down the system is not able to read the startup information from the hard drive and will not come on without me re installing it.
View 9 Replies
View Related
Mar 13, 2011
I have a XP/ubuntu 8.04 dual boot setup and I walked away from the PC for a minute and when I returned I had "SMART command failed error. Press f2 to resume" on-screen. I pressed f2 and it went to grub boot menu which gave error 16 and froze. I ran Ubuntu live cd which appears to freeze after selecting try without install(latest attempt appears to freeze on ubuntu logo loading up).
I ran Hiren CD miniXP but the My Computer doesn't recognize the disk nor does it appear in the disk management console. HDTune and a partition tool doesn't see the disk.I ran Hiren CD linux recovery but that loops with IO error. My latest attempt is running Ubuntu 10.04 Live cd which is appears to be loading, slowly at least.I have an external hard drive and usb stick ready to copy to. I also have my laptop. It will be greatly appreciated if someone can tell me how to get my files off the drive.
edit: just pressed esc and these lines keep appearing.
udevd[85]: worker [91] unexpectedly returned with status 0x0100
udevd[85]: worker [91] failed while handling '/devices/i0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0/block/sda/sda1'
worker[126] is sda2, 171 is sda3 and 172 is sda4.
View 2 Replies
View Related
Jul 8, 2010
I have a netbook running Windows XP as standard. There is also a recovery partition which came from the factory.
In the past I installed Ubuntu (I think 9.something) from USB key and all worked fine. However my XP became corrupted and I needed to do a repair on it. After this, Ubuntu became removed from the boot select menu.
Since then, Ubuntu has become updated to 10.04, which I now cannot install.
The Live CD tells me there is a "file IO error" and simply stops installation at around 70%.
I did manage to get into Ubuntu from a Live USB using Wubi. However when I chose to install Ubuntu to a Harddrive, the option to "install side by side" was missing.
After reading on the forums, I did a chkdsk /f on Windows and tried again. Now my liveUSB does not show a boot menu!
When I select to boot from USB stick, the screen goes blank with a flashing cursor. Ctrl+alt+dlt reboots.
I'm really lost here! It seems when I fix one problem, another problem arises!
Also when trying to instal Ubuntu within Windows, the process goes through to 100% and asks me to reboot. When I do so, the option for Ubuntu does show in the boot menu. However when I select it, I get an error "Windows boot failed: file wubildr.mbr and status: 0xc00000f - something is corrupt".
View 1 Replies
View Related
Sep 1, 2010
I had a a problem booting last night when my laptop battery came loose and caused a crash during boot.It ceased loading a daemon and I turned it off with the power switch, then I received the boot error,then i checked the linuxdrives directory and it was corrupt,I then, out of ignorance, ran wubi from within windows XP and said unistall believing that it would reinstall and fix itself.Thus you can see my green behaviour.I have been searching the threads and have tried many things but have had no success, I will suffer a great loss if I lose that load of Ubuntu as I have allot of work stored there, and in my Thunderbird accounts.
View 8 Replies
View Related
Aug 30, 2010
Last night when I turned on my lap top (5 year old Acer TravelMate 4650), it was not able to boot up (10.04 LTS). No system files could be read and a lot of error messages was displayed. In fact, it has done a few checks for disk error lately during boot up, but no further warnings given. I gave up recovering, and simply re-installed Ubntu 10.04. I was wondering if this could be related to a virus attack?
View 9 Replies
View Related
Mar 22, 2011
I just burned the iso of openSUSe 11.4 onto a dvd, and I make it through all of the installation. At the end it reboots the computer and starts in the kernel/command line or whatever you call it. I think it's kernel. Anyway, it asks for my username and password and then it says like "have fun.." () or something and then just has like my directory or whatever waiting for commands. Is there some command to start up the OS?
View 9 Replies
View Related
Jan 18, 2011
Voice logger boot failure-reports 'error reading block 33051'
View 1 Replies
View Related
Jun 1, 2011
I have a laptop set up for dual-boot with Ubuntu and Win7. I also have a shared partition which I mounted as the /home directory in Ubuntu. The problem occurred as I was upgrading Ubuntu from 10.10 to 11.04. In the middle of the install, my computer froze for some reason and ultimately I had to shut the computer off and restart. When I restarted the linux would freeze half-way through boot-up with a message saying that the drive was mounted. Before the message saying the drive is not mounted it gave the following error: Can not read 'etc/udev_rule.d/z80_user.rules'
When I boot up Win7 it is unable to mount the shared partition and says that the drive is not formatted. I am also unable to run the ubuntu recovery option from GRUB. It asks me to give the "root password for maintenance," but it won't accept my root password. Would the upgrade have wiped my partition??? Or am I just locked out somehow because it was in the process of changing config files?
View 6 Replies
View Related
Jul 17, 2010
IPtables creates an error during startup as well as when I try to restart it: Here's the output of:
[Code]....
View 11 Replies
View Related
Jul 8, 2011
I am new to Linux. I have installed RHEL 5.4 on my PC with preloaded Windows XP.
Windows was set as the first boot kernel. So if i do not choose which OS to be loaded it will load Windows by Default.
Today I got an error saying GRub Loading Stage2 read error.
View 9 Replies
View Related
Feb 23, 2011
I tend to get constant crashes when using internet browsers ( Google Chrome and Firefox ) basically the application hangs not moving in any way, then eventually completely freezes up, the system then locks up and finally crashes.
Upon system re-start I get "Read Error" at boot ( No further information, it literally just says "Read Error" ).
It is sometimes fixed by going into the BIOS and select "Hold on No Error".
I tried installing OpenBios to see if using different BIOS firmware would resolve the issue, but the OpenBios install failed ....so no dice there either.
I am trying to work out if it is a hard drive problem or if it is purely a problem with Fedora.
It was working fine for a couple of months and when it does boot up ... the system works fine, ( Until another crash ).
It seems like the internet browsers crash the system and then the system crashes and can then no longer remember how to boot up.
what this could be that could be software based....if not it looks like I will need a new hard-drive.
View 5 Replies
View Related
