Ubuntu :: Boot Failure - Error No Such Device
Jul 27, 2010
I installed from a live disc months ago. It worked fine for a while, don't remember what caused the change.
Now when I boot, I get this message:
Quote:
I have several hdds in this desktop box, one other has a OS on it, has the Hardy version. But i disconnected that (it all used to work with both drives connected and I was able to use that boot menu to change from one OS to the other). I can boot by getting to "boot menu" by pushing the "esc" key when the bios starts (just after the beep). It gives the option to start from, with a list of possible devices to choose from. I don't know where this menu is from, bios or other. I select hard drive, then select the correct hard drive and it starts right up. That is nonsense though. I really no longer need version 8.04 but keep it as a backup in case my preferred OS/hdd fails.
View 3 Replies
ADVERTISEMENT
Sep 17, 2009
Since May 12,2009. Our system lifekeeper has the error log "lifekeeper error: DEVICE FAILURE on SCSI device '/dev/add'", but it ran normally. Until last week, it failover to the standby server. The disk still running, the error still come out.
View 3 Replies
View Related
Jun 1, 2010
I'm a long time Linux user. Finally got around to upgrading my Fedora 11 system to Fedora 12 by using the 'preupgrade' tool. The upgrade appeared to go well (downloaded packages, rebooted into installer, etc). However, now that the upgrade is complete, I'm unable to boot my system.
Here's my configuration:
/dev/sda (80Gb)
200Mb /boot partition (ext3)
52Gb / partition (ext4 - managed as logical volume)
2Gb swap partition (managed as logical volume)
20Gb /spare partition (ext3 - managed as logical volume) .....
All worked fine under Fedora 11 for the last few months. Grub now presents me with 'Fedora' and 'Windows XP' boot options. The /boot/grub/menu.lst file is essentially the same as it was for Fedora 11, except for the different kernel versions, etc. The boot sequence shows the Fedora bubble (??) and gets about 80% full when the screen goes black and the message displayed is:
No root device found
Boot has failed, sleeping forever
If I boot Windows, all works fine.
Am able to boot using a SystemRescueCD disk. The disks all look okay and I can mount/modify all partitions, etc. The grub menu.lst file read as follows (sorry, typed in, not copied):
default=0
timeout=10
splashimage=(hd0,0)/grub/splash.xpm.gz
hiddenmenu
title Fedora (2.6.32.11-99.fc12.i686.PAE)
root (hd0,0) .....
View 2 Replies
View Related
Jun 26, 2010
I had occasion to add a few lines to rc.sysinit. Turns out the lines syntax was wrong. Instead of the booting ignoring those lines and proceeding on, then giving me an error warning or perhaps dumping into the interactive mode it just hung up! After several tries at moving on I discovered ESC dropped me into some sort of unannounced shell I got the installation disk out and with the repair system option using VI I got the lines deleted and all went back to normal. Now my suggestion is that if something does not make sense in terms of syntax while booting then cover it by doing the above and ignoring it with a warning later.
View 14 Replies
View Related
Mar 17, 2011
I just compiled my first own kernel (I'm using Arch Linux), following the tutorial on the german site. Now I tried to boot it, I ended up failing with this message: Code: Waiting 10 seconds for device /dev/sda1 ... Root device '/dev/sda1' doesn't exist, Attempting to create it. ERROR: Unable to determine major/minor number of root device '/dev/sda1' Here is the important part of my menu.lst:
[Code]....
I simply copy&pasted the Arch-entry, i.e. I also had the disk by uuid there. The failure message was the same, just the root device name was the different name Also, at first I did not have the initrd line in my menu.lst (as written in my tutorial that I may not need it). In this case I had this error message:
[Code]....
View 10 Replies
View Related
Feb 27, 2010
I just bought a brand new hardrive (40gb western digital) IDE, 10 pin.I have gone through the installation and partioned the hardrive, when it gets to 100% it asks me to reboot.So i take the disk out, and then it says DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER:So i press enter and i get the same message> How can i get Ubuntu to boot up?The computer is a 2003 Medion pc with 512mb of RAM And an AMD Athlon processor. The computer has a sticker on that says: Designed for windows xp.
View 9 Replies
View Related
Apr 16, 2011
Reboot and select proper boot device or insert boot media in selected boot device and press a key. I got this error after: Reducing my Windows 7 partition by about 100gb. Creating a new partition (100gb) and copying my Ubuntu partition (10gb) to the new partition. After it was copied, and pasted, the original partition was deleted. I now had two partitions a new 100gb Ubuntu partition and a 600gb (or so) Windows 7 partition.
All of this was done using a bootable USB with Ubuntu 10.10 and GParted partition editor. Now when I boot I get the "Reboot and select proper boot device or insert boot media in selected boot device and press a key." error.
View 9 Replies
View Related
Aug 30, 2010
Last night when I turned on my lap top (5 year old Acer TravelMate 4650), it was not able to boot up (10.04 LTS). No system files could be read and a lot of error messages was displayed. In fact, it has done a few checks for disk error lately during boot up, but no further warnings given. I gave up recovering, and simply re-installed Ubntu 10.04. I was wondering if this could be related to a virus attack?
View 9 Replies
View Related
Aug 11, 2011
I have a fresh computer with specs as such:
Hard Drive: Western Digital Caviar Black 500Gb 6Gbs Sata
Asus Sata DVD/CD Burner
Core i3 3.3GHz Sandy Bridge chipset
MSI P67A-GD55 Motherboard
Zotac GTS 450
I have a problem where the live cd gives this error message:
Boot failure, sleeping forever.
View 12 Replies
View Related
Jan 18, 2011
Voice logger boot failure-reports 'error reading block 33051'
View 1 Replies
View Related
Apr 22, 2011
I have a netbook with a 150GB hard drive in it. A while ago I dropped my netbook and it wouldn't boot. Had a "failed command: READ FPDMA QUEUED" error at startup. So naturally I went and reinstalled. Reinstalling worked fine and I had my computer back. What I didn't account for was the fact that anytime it lost power and didn't shut down properly, I'd get the same error. I can't seem to recover my data either. Can't get any live disks to mount the hard drive after this error but for some reason I can still reinstall Crunchbang (essentially debian). Now I know there are bad sectors or something because when I try to use the disk that came with the netbook with an image of Windows XP that writes to the entire hard drive it throws an error but linux will avoid this I suppose when installing.
Now all of this is to say, being a laptop, several times I have left it on overnight when I fall asleep working or have to run into to town and it'll die and then I lose all my data, rather irritating. What's causing this error? What can I do to prevent it besides getting a new hard drive? If I can't prevent it from happening in the future is there a way to recover the data off the hard drive? Here's the section of the boot log that contains the error: [url]
View 4 Replies
View Related
Sep 6, 2010
I switched to the linux-image-rt kernel a while back, and decided yesterday to switch back to linux-image-generic. Unfortunately, I couldn't remember how to do this properly, so I just uninstalled all of the linux-rt related packages and then changed the /vmlinuz and /initrd.img symbolic links back to what they used to be and rebooted. So now the machine gets stuck in a memtest whenever I boot from the HD. I'm having trouble figuring out how to fix things from a rescue CD. If I try chroot /mnt/hd (where my old system was), and then update-grub, for example, I get: /usr/sbin/grub-probe: error: cannot find a device for / (is /dev mounted?). So, basically I'm completely lost, but also sure that a working system isn't more than a few simple commands away. Can anyone throw me a bone?
View 2 Replies
View Related
Apr 5, 2010
I had a windows 7 professional on my computer. I tried dual booting it with ubuntu. While installing ubuntu when it asks which partition you want to install it "as it said your all data in the partition would be erased but not before you confirm" so I selected go back and aborted installation because I didn't wanted that and bang I start my system again an I get this error "no boot device found". I ran my hard disk test it say's passed so I don't think my hard disk is corrupted. I tried using windows 7 recovery disc but I guess it doesn't even detects a operating system on my laptop. I got no back up of my data. Any way to get back my data if I cant get windows back!
View 8 Replies
View Related
May 13, 2010
Today I installed Fedora (I need it for school), but not everything seems to work fine Before installing Fedora on my Macbook I had a triple booting machine: Mac OSX snow leopard, Windows 7 and Ubuntu. (using rEFIt) All of them where working. Since I installed Fedora on the 4th partition I can only boot Mac OSX. When selecting one of the other OS's it says: "no bootable device insert boot disk and press any key"
View 5 Replies
View Related
Jan 4, 2011
I have 10.10 installed and working OK. The Home directory is located on a second 1TB disk (sdb1). Recently, I've started to experience random boot failures where the start-up routine gets as far as showing the '10.10' logo with the progress dots underneath, but then throws up an error message saying that it cannot mount sdb1. I then have an option to Quit or drop into the shell to do a manual restart.
If I then do a Ctrl/Alt/Del, the system reboots, but usually fails again. Powering off and on, sometimes more than once, is the only way to eventually get a clean boot. The drive causing the problem is fairly new and all the diagnostic checks seem to indicate that it's healthy, so I'm not sure what causes the problem.
View 2 Replies
View Related
Jul 11, 2010
When I boot off of Debian Kernel 2.6.26-2-686. This is what happens. It stops at attached scsi generic sg5 type 0 After 4 or 5 minutes it comes back and says.
Gave up waiting for root device. Common problems Boot args (cat /proc/cmdline) Check Root= (did the system wait for the right device) Missing modules (cat /proc/modules; ls /dev Alert /dev/sdd8 does not exist dropping to shell /bin /sh: can't access tty; job control turned off If I boot off Debian Kernel 2.6.26-2-686 (single user mode) Then use Control-D it boots fine.
View 1 Replies
View Related
Jun 24, 2010
i downloaded backtrack 4 (final) and booted the iso onto a flash drive using unetbootin. i then changed the boot order so the flash drive was first. after i did that i got into backtrack 4 did the install.sh and now i cant boot windows 7. even after changing the boot order to default, i turn my computer on and get a message that says:
Ubuntu 8.10, kernel 2.6.30.9
Ubuntu 8.10, kernel 2.6.30.9 (recovery mode)
Ubuntu 8.10, memtest86+
Other operating systems :
Memory Test (on /dev/sda1)
Ubuntu 8.10, kernel 2.6.30.9 (on dev/sda1)
Ubuntu 8.10, kernel 2.6.30.9 (recover mode) (on dev/sda1)
Ubuntu 8.10, memtest86+ (on dev/sda1)
[Code]....
i can only boot backtrack 4 OS, i really want to know what can i do to be able to boot my windows 7 home premium os.
View 2 Replies
View Related
Nov 30, 2010
just installed ubuntu 10.10 on my external usb hdd from my 8gb flash drive doing this on a laptop, my primary hdd (internal) is running windows (230gb of 250gb used) so i got an external hdd (2tb) and I decided to install ubuntu on it
[Code]....
View 1 Replies
View Related
Jan 14, 2010
Recently installed some minor software, some games and Ubuntu Tweak, I am not sure if that's what caused this issue or not. I shutdown after the installations, then when I tried to start back up the small, white ubuntu logo appears just like it normally does, then it just goes to a black screen. I turned off the computer and restarted in (Recovery Mode). It goes about its thing then it says it is waiting for root file system, then after about 30 seconds it says "Gave up waiting for Root File System" how to fix this without reinstalling?
View 2 Replies
View Related
Jan 12, 2011
I had a working dual boot Ubuntu 10 and Windows 7. Anyways long story short, I got it working again but have lost the boot option for windows 7. If i run fdisk -l, I get the following.
root@support-Latitude-E6400:/home/support# fdisk -l
Disk /dev/sda: 250.1 GB, 250059350016 bytes
255 heads, 63 sectors/track, 30401 cylinders
[code]....
I installed gparted and can see that windows 7 is installed in dev/sda6. In another forum, i read that someone had to edit their menu.lst so i did with the following.
title=Windows 7
rootnoverify (hd0,6)
makeactive
chainloader +1
When i try to boot from windows 7, i get the following error. Error 12: invalid device request. How can i get my laptop to boot from windows again?
View 9 Replies
View Related
Jan 18, 2011
I had Ubuntu installed, i installed Debian and there was no dual boot. So i formated all the hard disk to install only Debian. It installed but at boot i get error: no such device and the grub rescue> prompt. i googled for a solution and nothing worked:
- i tryed reinstalling grub, not worked
- i did the windows cd fixmbr trick, not worked
- reinstalled debian with fixmbr the first step and nothing
- tryed deleting with dd the mbr, not worked
- reinstalled grub from debian rescue, not worked
what should i do? i can't access my computer? please tell me how should i fix it? the google guys will kill me because i put their servers on fire
View 14 Replies
View Related
May 7, 2010
I have a Feadora 12 Live CD. It booted up fine on my 700 Mhz computer. I've since then put a new HDD in with which I intended to install Fedora on. But now i get this message
Quote:
No root device found. Boot has failed, sleeping forever
What does this mean? How do get the Live CD to boot?
View 1 Replies
View Related
Dec 10, 2009
2 weeks ago, my power supply blew, during close-down. My system is a SUSE Linux 10.1 and openSUSE 11.1 dual boot with WInXP (for those family things). After replacing the power supply my system had no root partition, or loader. It said something like "Invalid Partition table". Grub had gone! So following swerdna's "How to Boot into openSUSE" tutorial I used the openSuse 11.1 install CD rescue option to get to the command prompt, su'd, went to grub and followed the stated commands. So far so good.
However the new grub entry openSUSE (Failsafe) has a problem. It starts to boot in the usual way, but I note fatal Module errors in the boot log relating to sata_nv not found, ide_pci_generic not found etc, and Fatal error inserting edd (/lib/modules/2.6.27.39-0.2-default/kernel/driver/firmware/edd.ko): no such device but uses udev as boot source until Waiting for device /dev/disk/by-id/ataST3120827AS-4M60PX7V-part6...... and then it exits to /bin/sh.
My fdisk looks
Dev Boot Start End Blocks Id Syst
/dev/sda1 1 1306 10490413 c w95 fat32
/dev/sda2 1307 2612 10690445 c w95 fat32
/dev/sda3 * 2613 14593 96237382 f w95 ext'd
/dev/sda5 5486 8096 20972862 83 linux
/dev/sda6 8097 10695 20987643 83 linux
/dev/sda7 10699 14593 31310653+ 83 linux
View 5 Replies
View Related
Sep 23, 2010
managed to get things working so well on my laptop i thought i'd install ubuntu onto an external drive so i can boot to either xp or Ubuntu whenever i want, when i started up after the install it doesn't recognise the drive i loaded it to and appears to have lost the link to xp. the exact words are:
error: no such device: 4368f21f-d1b6-4c60-8c6b-4d2d38d16920.
grub rescue>
what i can do to get my xp back, my wife uses the xp and will kill me if i don't sort it, fortunately the comps unrealiable anyway!
View 1 Replies
View Related
Aug 11, 2011
i have this problem i install android sdk, and i install libreries: libstdc++5, lib32stdc++6, lib32ncurses5 and libstdl1.2-dev,
now if i use ldd comand don't have problem, but when i use eclipse and i compile a simple example (hello word example), i have this
error: [Emulator] SDL init failure, reason is: No available video device i have a notebook toshiba satellite A300-1RI whit ATI Radeon 3650, i install the amd driver and all work well.
View 1 Replies
View Related
May 21, 2009
openSUSE Install/Boot/Login: I am looking for a Linux distribution with a working LTSP OOTB. LTSP-openSUSE / KIWI-LTSP looks interesting (http://en.opensuse.org/LTSP).
When I boot openSUSE-11.1-DVD-i586.iso, go through the installer, and attempt to use encrypted LVM, I get the following error dialog:
Code:
YaST2
Error Failure occurred during following action: Setting up encrypted dm device on /dev/sda2 System error code was: -3034
View 1 Replies
View Related
Jun 9, 2010
For backup purposes, I built a RAID6 array on USB. When during the night the backup filesystem is being mounted, every so many days, a random disk fails:
Code: sd 9:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 9:0:0:0: [sdb] Sense Key : Illegal Request [current]
sd 9:0:0:0: [sdb] Add. Sense: Invalid field in cdb[code].....
In other words, my RAID set fails every so many mounts, but I know how to fix it.What I want to find out is:
- Why is a random drive failed every now and then?
- How can I prevent that drive from being failed?
BTW: I have a second RAID set that has been functioning for years without error, so the setup I use must be correct. The only difference between both RAID arrays is the different vendor of the disks.
View 1 Replies
View Related
Jan 14, 2011
I insert my F14 CD and booted the computer; I see the beginning of the installation and the the screen goes black and says:
No root device found.Sleeping forever. Boot failure.
View 2 Replies
View Related
May 22, 2010
I initially thought the problem had to do with the Lucid Lynx upgrade, a lot of people have been reporting similar issues with drive mapping and things along those line. My issue is that an external drive, formatted in FAT32 appears to be corrupted, and overtime begins to read or mounts as 'read-only.'
What I've read, and deduced, is that this is ultimately and issue with the drive. I've backed it up, reformatted, and been able to write to the drive successfully, but I've been moving a lot of files (backing up) and the system has been reporting input/output errors in transferring some files (through the GUI).
The only thing I can think of, is that the device itself is corrupted or damaged, and that I need to be thinking of other back-up options for the future. Any suggestions on disk-doctoring? I'm hoping to do a clean-install of the OS once I back up my files manually.
View 1 Replies
View Related
Nov 10, 2010
I installed Xubuntu 10.04, and it was working somewhat smoothly(little drivers, but I could see and hear). Ran the update(as of 3 hours ago), and started up the machine. Here is what greeted me. Insyde ACPI BIOS Version 1.50.00 Date: 11/01/02 Copyright (c) 2002 Insyde Software, Inc. All Rights Reserved Attempting to boot a Hard Drive... error: no such device: 6a7820b6-708d-4c44-a057-a2aff1467203 grub rescue> I am not too sure how this happened, or what to do. The machine is a Kohjinsha SA1F00B AMD Geode LX 512mb and 80gb Hitachi HD.
View 1 Replies
View Related
