Slackware :: PHP Is Not Working On 13.37?
Jun 13, 2011I installed Slackware 13.37. I configured httpd.conf like this:
# Uncomment the following line to enable PHP:
#
Include /etc/httpd/mod_php.conf
[code]...
I installed Slackware 13.37. I configured httpd.conf like this:
# Uncomment the following line to enable PHP:
#
Include /etc/httpd/mod_php.conf
[code]...
I'm trying to bring my Slackware system back to life as my XP HDD is dying... I've got everything working except for my audio. I got a new motherboard (ASRock P43DE3) and it has a VIA VT1708S as the onboard audio. Is there any way I can get this working without rebuilding the kernel?
View 5 Replies View RelatedI recently bought the Alfa AWUS036h which uses the Realtek rtl8187 chipset. I am able to load the module and connect to any network, but its almost as soon as I try to load a page the connection drops. It never stays connected for more than 30 seconds. My other computers using the same adapter in the same spot work fine, unfortunately there not running slackware. I've tried compiling the newest stable kernel and checked the rd.inet1.conf settings.
View 6 Replies View RelatedHas anyone managed to get the moonlight extension which enables one to watch Sky TV working in slackware? I have the extensions for firefox and chrome but all I get is a blank screen.
View 5 Replies View RelatedMy USB printer stopped working after I upgraded Slackware, using the Current.Also can not install any USB printer. CUPS version 1.4.2.
View 14 Replies View RelatedI am fairly new to this and I cannot get a watchport V2 webcam in working slackware 13.
It seems to be recognised;
Bus 003 Device 002: ID 1608:4001 Inside Out Networks
I have Slackware 13.1 with kernel 2.6.37. Everything is working fine, except that I can't mount any CD/DVD and automount is not working either. If I connect any USb to my laptop it doesn't automount, I need to manually mount it. The same case happens with CD/DVD only that I can't mount any CD/DVD even manually. Here's the output:
Code:
bash-4.1# mount /dev/cdrom /mnt/cdrom
mount: block device /dev/sr0 is write-protected, mounting read-only
[code]...
I installed vmplayer, run the bundle script, couldn't see what got installed where, just as in Windows so it seemed. There is no uninstall script I started vmplayer and got a list of messages.
(vmware-modconfig:4131): Gtk-WARNING **: GModule (/usr/lib/gtk-2.0/2.10.0/engines/libxfce.so) initialization check failed: Gtk+ version too old (micro mismatch)
(ten times)
(vmware-modconfig:4131): Gtk-WARNING **: GModule (/usr/lib/gtk-2.0/2.10.0/engines
[code]....
Some modules are missing in the generic kernel.As well as a 'VMware module kernel updater' screen saying that the Kernel headers for version 2.6.29.5-smp were not found. They are clearly present..
I set up a job in my crontab file to clear the /tmp file on bootup with the following line:
Code:
@reboot rm-rf /tmp/*
My /tmp folder is not clearing. I've never used cron before;
I have an old laptop.The laptop's 2 keys(g-h) are not working.I think the keys assign to different keys that the keys are windows keys near CTRLs because linux dont use these keys.Can I assign not working keys to the windows keys?
View 9 Replies View RelatedI know there are SlackBuild scripts for installing LibreOffice, but I wanted to compile my own packages. So I downloaded the RPMS and then converted them using rpm2tgz and used pkgtool to install all the packages.
Until then everything was fine. No warnings, no errors. But when I tried to run the various applications e.g. Impress, Writer etc. It didn't work. When I try to open any application, nothing happens. Just the icon bounces beside the KDE cursor for sometime.
I just setup a dual boot on my laptop with Windows 7 and Slackware 13.1
I've been using Slax for one of my web programming classes and I got tired of booting from a live CD all the time so I decided to just use Slackware. When I try and connect to the localhost page, I get a cannot connect error page. Why?
I'm looking forward to see the new 13.1 Slackware release although I always stay -current. Just a quick one I've found: When the RC1 was announced the mc-20100509_git-i486-1 broke the standard use of
Code:
mc -e
is this going to be permanently repleaced by
Code:
mcedit
or a bug?
I want to make my pad to (vertical) scroll since i do not use a mouse on my laptop (Slackware 13.0 on a Toshiba Satellite 2450 laptop).
View 2 Replies View RelatedI was reluctant to start yet another sound thread, but after days of searching sites and reading mini HOWTO's I'm still mute. I have tried configuring ALSA via:
# alsaconf
# /etc/rc.d/rc.alsa start
# alsamixer - all relevant sliders unmuted...
# alsactl store
...and still nothing. KDE reports that 'Audio playback device ALC889 does not work.' My kmix app doesn't even start. At boot I get this message 3 times:
"ALL CONFIG FILES NEED /etc/modprobe.d/sound - it will be ignored in a future release"
Even starting xmms brings up 'Check that - your soundcard is configured properly/the correct plugin is selected/no other program is blocking the soundcard'. btw, Windows reports I have an ALC888, not a 889. KDE lists it as present as both digital and analog, and the legacy system (whatever it is) as well as esound, but none work. I certainly had no difficulty with S11.
I am a newbie in Slackware. This is my first try to make working system on slackware. I made internet connection by help netconfig. Internet is working but not always. To example I try download page but it doesn't. I push Update page .. and one more time Update page and after 3-4 times my page is downloaded. When I work with windows on this computer, I don't have any problem.
View 3 Replies View RelatedHow to get a older crt touchscreen working. I need it to work for a handicapped child. When I check the device it seems slackware detects it as a mac emulation mouse and I installed egalaxy drivers. It seems something is right, when I touch the screen the cursor goes to the right top corner and moves a bit when touching the screen.
View 5 Replies View RelatedI am trying to get freecad working on my 13.37 64 bit There must be a problem with xerces-c slackbuild This is what I get running the slackbuild checking for C compiler default output file name. configure: error: C compiler cannot create executables See `config.log' for more details. the last line in the config.log is
configure: caught signal 2 configure: exit 1 I am dumb founded tried with src2pkg but that gives another error Skipping compile_source - FAILED!! No INSTALL_LINE given.
I have a XPS 1530 and when I type
lsusb
[code]
It seems to be that the camera is recognized by the OS but it is not working when I try to use it in skype or in EVO.
Bluetoothd is running.
bash-4.1# pgrep bluetoothd
25394
But when I start blueman-applet the icon on the toolbar is like white with a red 'x' in the centre of it, which doesn't seem right. I'm using fluxbox as my WM so don't know if that's the reason, but blueman isn't responding when I try to setup the device with gui (blueman-applet). My groups for my user are.
Users wheel floppy audio video cdrom plugdev netdev scanner
Hci0 is up.
bash-4.1# hciconfig
hci0:Type: BR/EDR Bus: USB
BD Address: 11:11:11:11:11:11 ACL MTU: 678:8 SCO MTU: 48:10
UP RUNNING PSCAN
RX bytes:2592 acl:0 sco:0 events:75 errors:0
TX bytes:800 acl:0 sco:0 commands:66 errors:0
i have problem to get my 5.1 surround sound card to work properly on Slackware 13.37 with example the Mplayer, Spotify or even when watching movie-clips at .....s. I have searched through forum but havent find any solutions to this problem.I have tested my sound card and it seems to work properly when executing "speaker-test -Dplug:surround51 -c6 -t wav" in the terminal. I have saved the ALSA settings through "alsactl store". But like i said, it still doesnt work with explicitly programs like Mplayer or Spotify, it still plays the sound as 2.1 (stereo).
View 3 Replies View RelatedI am attempting to setup wireless in Slackware 13.37 for the first time and while I found a lot of guides I am still unable to connect to my router without starting X and using wicd. I'll post my rc.inet1.conf and rc.wireless.conf along with wireless-settings.conf from wicd. wireless-settings.conf
Code:
[00:26:F3:22:33:7A]
automatic = False
[00:26:F3:22:33:79]
afterscript = None
dhcphostname = Doctor
bssid = 00:26:F3:22:33:79
[Code]...
I have read a few thread about different Attansic drivers and keep seeing L1 and L2. I have no idea which version of this driver I have. Wireless works just fine, but I would like to have the wired option. I am running 13.1 on an Asus EeePC 1001PXD, and here is my lspci
00:00.0 Host bridge: Intel Corporation Pineview DMI Bridge
00:02.0 VGA compatible controller: Intel Corporation Pineview Integrated Graphics Controller
00:02.1 Display controller: Intel Corporation Pineview Integrated Graphics Controller
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02)
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation Tigerpoint LPC Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation 82801GR/GH (ICH7 Family) SATA AHCI Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
01:00.0 Ethernet controller: Attansic Technology Corp. Device 2062 (rev c1)
02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
I see the "starting calculator" icon but it just disappears after a few seconds. If gcalctool is run from a terminal it prints Code: GLib-GIO-ERROR **: Settings schema 'org.gnome.gcalctool' is not installed The way to fix it : Code: cd /usr/share/glib-2.0/schemas/ glib-compile-schemas .
View 1 Replies View RelatedOn my netbook here, I did a fresh install of --current.
I cannot get hibernate to work, it seems to fall back to suspend.
In /var/log/pm-powersave.log I get this message:
/usr/lib/pm-utils/power.d/sched-powersave false: success.
Running hook /usr/lib/pm-utils/power.d/wireless false:
Turning powersave for wlan0 off...Error for wireless request "Set Power Management" (8B2C) :
SET failed on device wlan0 ; Operation not supported.
Failed
The netbook then seems to fallback to suspend at that point.
I got a new laptop Toshiba L526. Now I want to make it's Function keys work. I have read many threads, and found it is better using acpi.
But when I try
modprobe toshiba_acpi
it got a error :
FATAL:Error inserting toshiba_acpi(/lib/modules/2.6.29.6-smp/kernel/drivers/platform/x86/toshiba_acpi.ko): No such device.
My slackware version has upgrade to current exclude the kernel packages and alsa. The kernel I use is 2.6.29.6-smp. When I run acpi_listen,no output.
i'm using slackware 13.37. (Sony Vaio VGN-FS315H)
my fans are working all the time, they are loud and it's annoying.
I already did sensors-detect, but I get this message every time.
Code:
Sorry, no sensors were detected.
This is relatively common on laptops, where thermal management is handled by ACPI rather than the OS.
Yesterday I used slackupdate.sh [0.7.3] from darklinux.net to update Slackware 13.1, 32 bit version. I got Firefox 3.6.6, installed it, moved the libflashplayer.so to the new plugins directory. Now I can't play utube videos. about: plugins says that flashplayer is installed and working. Grabbed flash from Adobe website, overwrote the existing one, still no joy. Asked in the Firefox user forum. Answer 'same thing happen to me -- Windows Vista' ...I'm not an advanced user. So, is this a Slackware problem, an Adobe problem, or a Firefox problem? I'm asking here because y'all are more likely to point me to a solution. I've always been able to grab the Linux version of Flash from Adobe website and install it
View 7 Replies View RelatedI'm on Firefox 3.6.11 with Flash 10.2 d161 on Slackware 13.1 32-bit. Hulu stopped working sometime this past week. (Actually when it stopped working I was still on the previous versions of Firefox and Flash - I upgraded 3.6.10 to 3.6.11 to see if it would help.) Worked fine before that. I've tried Firefox safe-mode, disabling add-ons and using default theme and none of this matters. Flash works fine and Hulu worked fine before a week ago.
View 5 Replies View RelatedWhile I will not dispute this is not for everyone, I was wondering is there a trick to get webcollage working in Slack 13?
It works from the command prompt with something like this: /usr/libexec/xscreensaver/webcollage -vvv -size '800x600' -imagemap crazy
Just wondering why the Xscreensaver portion seems to be defunct.