I've got 13.1 x86_64 installed on /dev/sda2, and I would like to have 13.1 x86 installed on /dev/sdb2. How do I setup lilo.conf to handle this? While installing 13.1 x86 on /dev/sdb2 I skipped the LILO step, so what I currently have is a full 32 bit Slackware 13.1 install on /dev/sdb2, but no way to boot it.
View 2 Replies
I'm trying to take my current windows7 (x64) setup and make it into a dual-boot setup with slackware 13.0 (x32) and am hitting a brickwall. I guess I would like to know if I can salvage the situation without formating my windows drive. I fully intend to, but I had hoped to not do it this month. I'd like to get dual boot going so I can master it and acquire all the files/drivers I'll want and then format and do it 100% right next time.
Currently I have windows setup on a 3x 500gb Raid0 onboard array which itself has been flawless. After I shrunk my current partition size to give me about 25gb of free space I proceeded to setup Linux, and I was unable to perform the cfdisk portion for partitioning the array for Linux.
I tried using cfdisk:
/dev/hdx (a1-a3,b1-b3)
/dev/sdx (a1-a3,b1-b3)
I even attempted to locate with: cat proc/partition and tried using cfdisk on every device it located. It always said it was either an unknown partition table and should I start at zero, or bad partition. I was of course too concerned over my windows setup (which has almost 1tb of stuff I have not backed up) to go any further into the unknown.
PS: I have used Slackware before, back at 8.1, 10, and even a very brief interlude at 12.0, this is my first attempt on this computer however with 13.0, it is currently running fine on my laptop and my PS3 (Laptop is even dual booting 7/Slack13. Albeit without raid)
Phenom 9850
M2N-SLI Deluxe (Nvidia AM2)
4x1gb of 1066 kingston hyperX
3x500gb WD Caviar Black Sata2 3.0
I created a dual monitor setup in Slack 13.37 using the KDE systemsettings -> Monitor Setup function. (Sadly I had to rebuild ~/.kde in the process, but that's a different story.)
I verify that ~/.kde/share/config/krandrrc contains the new monitor setup (both screens active). I have saved a startup session with krandrtray running. However, when I logon, the system always starts with both screens in clone mode. I always have to go into systemsettings or krandrtay and redo the dual monitor configuration.
Is there a better way? Do I have to create a suitable xorg.conf (which I will try when I get home) or is there another way to boot into the dual config automatically?
Boot process ends up as shown at attached jpg.I use Biostar motherboard P35D2-A7 When I tried to use the kernel on the installation dvd I got working system. But no succes with huge or generic (with initrd) kernels.
View 3 Replies View RelatedPartition info:
sda2: Win7
sdb1: /boot
sdb2: LVM, containing , home, swap...
[code]....
I'm trying to install Puppy 525 on my Slackware 13.37 PC as a dual-boot using LILO. Puppy is living, all on it's own, in sda6, a 6 GiB partition. It got there by using the Puppy Universal Installer and selecting a 'Full' install, not a 'Frugal' install. I cannot find 'LILO' type instructions, only 'GRUB' type instructions.
Has anyone succeeded in doing a hard drive install of Puppy with the LILO boot loader?
Edit: I'll probably regret it, but I used Puppy's GRUB installer.
I installed Slackware 13.1 and Windows server 2008, I also installed LILO in MBR, I Found I can boot into slackware, but can't boot into Server 2008. then I　use command bootsect/fixmbr. now I can boot into server 2008, but the problem is I can't boot into slackware. I try to install lilo to supper sector. it's not works. I only can boot my slackware by a USB stick.who can help me to solve this problem? I really need these two systems.
View 5 Replies View RelatedI just did a fresh install of slack 13.1 on a separate drive to the one I was previously using. I've been having trouble getting lilo to work, so that I can choose between either drive. Lilo is currently installed to /dev/sda, with the old system on /dev/sda1 and the new installation on /dev/sdb1. I keep getting errors like these:
Code: Fatal: Trying to map files from unnamed device 0x0011 (NFS/RAID mirror down ?)
I managed to install lilo from the old system by copying the kernel image from the new system into the /boot/ directory and running lilo. I am now on the new system and trying the same thing in reverse but it isn't working. I have searched around a bit and there's a lot of talk of chroot-ing into the other partition to run lilo. I don't understand why the process isn't working both ways though. I can't run lilo on my new installation even with the two kernel images in the local /boot/ folder. Is this something to do with btrfs or am I missing something to do with lilo? This is my lilo.conf file. I am trying to run lilo using this file from my new installation on /dev/sdb1 and getting the error given above.
[Code]...
My new job requires I use Windows and as such I put a second HDD in my laptop for the purposes of Window/Work The issue is that Windows will not install on this second disc (Windows cannot create partition or install to disc). I got around this by installing Windows to the first disc, then the second then putting Slackware back on the first but then I suffer the "Bootmgr cannot be found, press ctrl + alt + delete to restart".
I am using Lilo and I have never really had an issue dual booting them on the same disc (Admittedly over a year ago) but it is of the utmost important I have them on separate Discs. Has anyone encountered this and/or know a way around?
how to set up a dual boot. I know that I have to partition the drive but at the moment Ubuntu is taking up the whole drive, so would i still be able to partition without loosing anything?
View 6 Replies View RelatedSo I got slackware 13 from the website and created 4 partitions (primary) and left some (100GB) space as I planned to install windows 7 in that. After installing slack, when I booted from windows DVD (rtm) in partition section it said I already have 4 primary partition so windows cannot used the rest of space despite the fact that it was free (windows even grayed all options like new partition and format etc. for that space). So I thought I'd create 2-3 primary partition for linux (slackware) so that windows can use the free space and make it a primary partition.
So, Next I formatted with slack (3 partition, 2 Primary, 1 extended, total space for slack 50GB) and after its installation I worked my way with windows, but it just created one partition of 100Gb, won't let me create any saying all primary partitions are created. Anyway, I created that partition and installed windows 7. But it messed up my lilo (slack won't show in boot menu) neither can I create any new partition.
After all I reformatted again created 2 partitions for windows (that actually became 3 as windows 7 create 100Mb separate partition for system). Installed windows correctly. Then I booted with slack , which allowed only creating 1 partition as 3 were already there. So I created 1 extended partition, in which I created 4 partition 1 to mount for /boot (100M), 1 for /swap (3G), 1 for home (10G), 1 for / (35G) everything worked fine till I reached last point to install lilo. At that point it said cannot install Lilo (I tried all options simple, expert, install to MBR etc.) but it just won't install. Anyway, after that it said you can install it manually so I clicked OK. Then it said setup complete, remove disk and press alt+ctrl+del to reboot, which I did. But there is just windows 7, no slack ?
how to install fedora on a hdd that already has xp sp2 and setup a dual boot.
View 2 Replies View RelatedI recently installed Ubuntu and I am dual booting it with Windows 7. I showed it to my friend and he likes it. He wants me to dual boot his computer with Ubuntu, also.We were wondering if there was a way to configure GRUB and that stuff so that it doesn't go to the GRUB boot screen when you start your computer where you pick an OS. We were wondering if you could set a default OS that the computer automatically booted to, unless you press a button at startup, and then you could get to GRUB to pick a different OS.
The reason being is because his whole family uses the computer, and we don't want to confuse them with GRUB every time they start up the computer. We just want the computer to boot to Win7 by default, but being able to boot into Ubuntu if you press a button to get to GRUB when booting.
I bought my wife an HP Mini [URL].. and want to get Ubuntu Netbook running on it. It comes with Windows 7 Starter, which we want to retain because Netflix won't run with Linux (gives you some BS error about "your browser is compatible, but your OS isn't"). So, I'd like to dual boot.
My desktop right now runs Kubuntu, and then I can boot in XP using VirtualBox OSE. Owing to the fact that the netbook is down on power relative to my desktop, doesn't seem like a good idea on the netbook, hence dual boot. I've seen a lot of "help, I just screwed this up!" threads, and since HP wasn't kind enough to send along a disc with Windows 7 on it, I need to get this right the first time. So, I'm going to post what I'm planning to do, let me know if I'm going to mess this up. I've compiled the below looking through a bunch of previous threads.
1) Defrag Windows drive
2) Use Windows 7 software to shrink the Windows partition
2b) Do NOT create a new partition using Windows software, just keep it unallocated
3) Boot off of USB key with Ubuntu in it, select unallocated space for install
Questions:
1) When I boot the computer up, I should get a GRUB screen asking which OS I want to boot into, correct?
2) I'm downloading 11.04 right now...anything to watch out for?
3) I couldn't find an install file for Ubuntu Netbook, do I make that selection during the install?
just spent hours trying to set up a dual boot with windows 7 and ubuntu. i now have both installed, however, i dont know how to load ubuntu. it automatically loads windows 7 on boot.
p.s both 64 bit if that matters.
I have a laptop running windows vista already and I need to run Red Hat 7.2/7.3 or Fedora Core 1 on there as well. I am in the process of downloading Red Hat 7.3. I haven't done this before so I'm wondering if there are any guides out there that detail how to set this up to dual boot? Is Red Hat 7.3 a better option over Fedora Core 1?
View 2 Replies View RelatedI just got a 1.5 tb I want to do a dual boot fedora 10 and vista. I don't have vista now. Can I install fedora 10 on a 200 gig partition and install vista on the rest when I buy it later?
View 3 Replies View RelatedHow to correctly install F11 on the same disk as Windows. I have created the partition but can't tell what F11 install to use to setup as dual boot with Windows XP Pro 64bit.
View 2 Replies View RelatedWindows 7 is first boot disk. Installed Fedora 13 on second disk from DVD. During installation it did not ask if I wanted dual boot. Fedora installed fine on second disk. Rebooted and only Windows will lood. How to setup to dual boot? Can I modify Windows Boot file? or do I have to install Grub on to sda. How do I do that?
View 2 Replies View RelatedI've been wanting to start using Linux for years now and after doing some research on which distro to use, I've decided to give it a try with openSUSE and ordered a DVD copy from Novel last night. Needless to say, I'm a newbie to Linux. I'm building a new computer with two identical hard drives and I'd like to install openSUSE and XP on them and hence make a dual boot system. This is also going to be my first time setting up a dual boot. So, while I'm waiting for the openSUSE DVD to arrive, how to actually set it all up?
View 6 Replies View RelatedI just bought a Dell 537s machine and configured it for dual boot of Windows 7 and Kubuntu 9.10. On my old dual boot machine I had the Windows System and the Linux System on different disk partitions. That way I could write fstab in such a way as to make the Windows System read-only as seen from Linux, so Linux couldn't mess up any Windows System files (and since Windows can't read ext3, Windows couldn't mess up the Linux System).
But the new machine came with Windows 7 installed and gobbling up 3 primary partitions. Kubuntu installed itself in such a way that Linux can read/write to the Windows System. This makes me nervous that Kubuntu might be able to mess up Windows 7.
Is there any way to make specific Windows 7 directories/files unwriteable as seen from Linux without altering their behavior in Windows 7?
I have created 5 partitions:2 GB ext320 GB ext310 GB ext320 GB ntfs400 GB ntfsI have already installed XP on 20GB ntfs. Will dual boot work if I use the 3 ext3 partitions to install Ubuntu?
View 4 Replies View RelatedI have a windows 7 machine and installed ubuntu 10.4 32 bit in its own partition. I want to replace the 32 bit ubuntu installation with a 64 bit installation. I downloaded the 64 bit version, booted up on the install cd, and started the install. I got as far as the partition set up before chickening out. I was going to use the manual partition option, select the existing ubuntu partition, reformat, and install. I chickened out because i was afraid that this would also reinstall the grub boot loader without the dual boot option disabling my ability to get into win 7. How should i proceed so that i can replace the existing 32 bit ubuntu with a fresh 64 bit install and still be able to boot into win 7?
View 4 Replies View RelatedI currently have xp installed on the 1st partition and Ubuntu installed on the 2nd.Both partitions are on the same drive.(Being the 1st drive)I have just purchased a new case and some other components and wish to take the opportunity to change my current setup so that xp is on the 1st drive (alone) and Ubuntu on the 2nd drive (alone) Using clonezilla, I take a backup of each partition separately.I then copy back the xp partition to the 1st disk. I then copy back the Ubuntu partition to the 2nd disk.I gather at his point i run the live Ubuntu cd, open a terminal and run sudo update-grub.
View 2 Replies View RelatedI 'm currently using grub to dual boot Windows Vista and Ubuntu 10.10.These are some of my partitions:
- one NTFS partition for Vista
- one NTFS partition for my Vista Data (shared with Ubuntu)
- one ext3 partition for Ubuntu (mounted at /)
- one very large ext3 partition for my Ubuntu home folder (mounted at /home)
I would now like to add Windows XP to this setup, but I am not sure where to start.I know I need to somehow shrink the large ext3 partition so I have an extra partition for XP, which should be NTFS.Then I assume I need to install XP on this partition, and somehow make XP appear in grub.how to do these things. Can anyone help? Please keep the instructions very basic, do not assume that I know anything.
The time in my Fedora 12 x64 installation is 5 hours behind what it should be. When I change it to the correct time, Windows XP x64 is now 5 hours ahead! (Dual boot setup). How I can sync the times on both os's. Both are set to GMT-5.
View 4 Replies View RelatedUsually I have no problems with linux but with fedora it didnt automatically set up the dual boot with vista. I cant remember how to set up grub to boot vista, how to set this up.
View 1 Replies View Relatedasus K60IJ intel 4400 dual-core 4gb ram trying to setup suse 11.2 64bit as dual boot. works fine with win7 in dual boot and system boots great. been following forums to setup wireless. after doing all term commands, it see's both built in wireless (atheros ar9285) on the pci-e and the usb verizon broadband modem as (curitel brand modem). after checking kernal dmesg, it see's devices but looking at usr/sbin/iwconfig, it see's no eth0. checked at the asus website and see nothing on getting any kind of ethernet drivers.
View 7 Replies View RelatedI am planning to move my main OS from Windows to Ubuntu (Yeah I am that impressed) but I wish to move windows to my current smaller hard drive until I find all ubuntu replacement programs i can use then eventually eject the windows drive. The problem is has we all know who dual-boot you have to install windows first before ubuntu as the windows mbr is when grub is stored and gets wiped when you install windows.
It must be possible to add windows as secondary OS while keeping / or reinstating grub must it not it surely (eg on 10.4LTS release it would be ok, but if i installed windows vista or 7 on my secondary hardisk it would destroy grub).
I have always use dual-booting vista--ubuntu, I am getting bit tired of windows, so I want to install ubuntu, specially lucid is coming soon. I want to have the possibility to install windows in case I will need it in the future, like working with Visual Studio, ubuntu always detect if windows is installed, if windows is installed first, does windows also detect if ubuntu is installed ?
View 8 Replies View Related
